Manual Toshiba TECRA A50-A/W50-A

166 pages 2.86 mb
Download

Go to site of 166

Summary
  • Toshiba TECRA A50-A/W50-A - page 1

    User's Manual TECRA A50-A/W50-A Satellite Pro A50-A series ...

  • Toshiba TECRA A50-A/W50-A - page 2

    Table of Contents Chapter 1 TOSHIBA Legal, Regulatory and Safety Copyright, Disclaimer and Trademarks .............................................. 1-1 Regulatory Information ......................................................................... 1-2 Video Standard Notice .......................................................................... ...

  • Toshiba TECRA A50-A/W50-A - page 3

    LAN ....................................................................................................... 4-32 Additional memory module ................................................................ 4-33 Memory media ..................................................................................... 4-44 ExpressCard .......................... ...

  • Toshiba TECRA A50-A/W50-A - page 4

    Chapter 1 TOSHIBA Legal, Regulatory and Safety This chapter states the Legal, regulatory and safety information applicable to TOSHIBA computers. Copyright, Disclaimer and Trademarks Copyright © 2013 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permissi ...

  • Toshiba TECRA A50-A/W50-A - page 5

    The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Toshiba Corporation and its affiliates is under license. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other ...

  • Toshiba TECRA A50-A/W50-A - page 6

    Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitt ...

  • Toshiba TECRA A50-A/W50-A - page 7

    EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA EUROPE GMBH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet. CE com ...

  • Toshiba TECRA A50-A/W50-A - page 8

    Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA. The consequences of the use of this product in non-approved working environments may be: Interference with other devices or machines in the near surrounding area. Malfunction of, or data loss from, this produc ...

  • Toshiba TECRA A50-A/W50-A - page 9

    Following information is only valid for EU-member States: Disposal of products The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres. The black bar in ...

  • Toshiba TECRA A50-A/W50-A - page 10

    These symbols may not stick depending on the country and region where you purchased. REACH - Compliance Statement The new European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007. TOSHIBA will meet all REACH requirements and is committed to provide our c ...

  • Toshiba TECRA A50-A/W50-A - page 11

    Video Standard Notice THIS PRODUCT IS LICENSED UNDER THE AVC, THE VC-1 AND MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (I) ENCODING VIDEO IN COMPLIANCE WITH THE ABOVE STANDARDS ("VIDEO") AND/OR (II) DECODING AVC, VC-1 AND MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ...

  • Toshiba TECRA A50-A/W50-A - page 12

    5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project. 6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in t ...

  • Toshiba TECRA A50-A/W50-A - page 13

    This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the copyright notice, this lis ...

  • Toshiba TECRA A50-A/W50-A - page 14

    Copyright 1996-2002, 2006 by David Turner, Robert Wilhelm, and Werner Lemberg Introduction ============ The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools and contributions which rely on, or relate to, the FreeType Project. This license applies to all fil ...

  • Toshiba TECRA A50-A/W50-A - page 15

    authors (David Turner, Robert Wilhelm, and Werner Lemberg) as the `FreeType Project', be they named as alpha, beta or final release. `You' refers to the licensee, or person using the project, where `using' is a generic term including compiling the project's source code as well as linking it to form a `program' or `executabl ...

  • Toshiba TECRA A50-A/W50-A - page 16

    -------------- Neither the FreeType authors and contributors nor you shall use the name of the other for commercial, advertising, or promotional purposes without specific prior written permission. We suggest, but do not require, that you use one or more of the following phrases to refer to this software in your documentation or advertising material ...

  • Toshiba TECRA A50-A/W50-A - page 17

    ENERGY STAR ® Program Your Computer model may be ENERGY STAR ® compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy effici ...

  • Toshiba TECRA A50-A/W50-A - page 18

    Optical disc drive safety instructions Be sure to check the precautions at the end of this section. The drive model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of cont ...

  • Toshiba TECRA A50-A/W50-A - page 19

    General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the ...

  • Toshiba TECRA A50-A/W50-A - page 20

    Stress injury Carefully read the Instruction Manual for Safety and Comfort . It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. It also includes information on work space design, posture and lighting that can help reduce physical stress. Heat injury Avoid prolonged phy ...

  • Toshiba TECRA A50-A/W50-A - page 21

    Moving the computer While the computer is designed for flexible day-to-day usage you should exercise a few simple precautions when moving it in order to help ensure trouble-free operation. Make sure all disk/disc activity has ended before moving the computer. Turn off (shut down) the computer. Disconnect the AC adaptor and all peripherals before mo ...

  • Toshiba TECRA A50-A/W50-A - page 22

    Safety Icons Safety icons are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions. A caution informs you that improper use of equipment or failure to follo ...

  • Toshiba TECRA A50-A/W50-A - page 23

    Chapter 2 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and ...

  • Toshiba TECRA A50-A/W50-A - page 24

    Right-click Click the right Touch Pad control button once. Right click the mouse once. Press and hold on the touch screen (only for touch screen models). Double-click Tap the Touch Pad or click the left Touch Pad control button twice. Left click the mouse twice. Tap the touch screen twice (only for touch screen models). HDD or Hard disk drive Some ...

  • Toshiba TECRA A50-A/W50-A - page 25

    Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a ...

  • Toshiba TECRA A50-A/W50-A - page 26

    1. Connect the power cord to the AC adaptor. Figure 2-1 Connecting the power cord to the AC adaptor Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. 2. Connect the AC adaptor’s DC output plug to the DC IN 19V jack on your computer. Figure 2-4 Connecting the DC output plug to the computer 1 2 1 2 1. D ...

  • Toshiba TECRA A50-A/W50-A - page 27

    Opening the display The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity. Figure 2-5 Opening the displa ...

  • Toshiba TECRA A50-A/W50-A - page 28

    Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Power Condition Descriptions section for more information. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Volume cannot be adjusted during Windo ...

  • Toshiba TECRA A50-A/W50-A - page 29

    Shut Down Mode When you turn off the power in Shut Down Mode, no data will be saved and the computer will boot to the operating system's main screen the next time it is turned on. 1. If you have entered data, either save it to the HDD/SSD or to other storage media. 2. Make sure all disk/disc activity has stopped before removing the disk/ disc. ...

  • Toshiba TECRA A50-A/W50-A - page 30

    shut down the computer. This includes turning off any wireless communication functionalities, and cancelling settings that reactivate the computer automatically, such as a timer recording function. Failure to completely shut down the computer in this way could allow the operating system to reactivate and run pre-programmed tasks or preserve unsaved ...

  • Toshiba TECRA A50-A/W50-A - page 31

    Executing Sleep Mode You can enter Sleep Mode in one of three ways: Click Start . Point to the arrow ( ) beside the Shut down button and then select Sleep from the menu. Close the display panel. Please note that this feature must be enabled within the Power Options. Press the power button. Please note that this feature must be enabled within the Po ...

  • Toshiba TECRA A50-A/W50-A - page 32

    Saves data to the HDD/SSD when the computer automatically shuts down because of a low battery condition. You can return to your previous working environment immediately when you turn on the computer. Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature ...

  • Toshiba TECRA A50-A/W50-A - page 33

    Chapter 3 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section. Please handle your computer carefully ...

  • Toshiba TECRA A50-A/W50-A - page 34

    Memory media slot This slot lets you insert an SD™/SDHC™/ SDXC™ memory card, miniSD™/microSD™ Card and MultiMediaCard™. Refer to the Memory media section for more information. Keep foreign metal objects, such as screws, staples and paper clips, out of the Memory media slot. Foreign metal objects can create a short circuit, which can cau ...

  • Toshiba TECRA A50-A/W50-A - page 35

    Fingerprint Sensor This sensor enables you to enroll and recognize a fingerprint. Some models are equipped with a Fingerprint Sensor. Left side The following figures show the left side of the computer. Figure 3-2 The left side of the computer 5 1 6 5 4 3 2 8 5 1 6 5 4 3 7 1. Cooling vents 5. Universal Serial Bus (USB 3.0) ports 2. DisplayPort* 6. H ...

  • Toshiba TECRA A50-A/W50-A - page 36

    Universal Serial Bus (USB 3.0) port Two Universal Serial Bus ports, which comply to the USB 3.0 standard, are provided on the left side of the computer. The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices. USB 3.0 port(s) may work as USB 2.0 port(s) when operating in USB Legacy Emulation mode. Please not ...

  • Toshiba TECRA A50-A/W50-A - page 37

    Figure 3-3 The right side of the computer 6 1 7 5 4 3 2 8 1 7 5 3 3 2 1. ExpressCard slot or PC Card slot* 5. LAN jack 2. Optical disc drive* 6. DC IN 19V jack 3. Universal Serial Bus (USB 2.0) port* 7. Security lock slot 4. Serial Connector* 8. DC IN 19V jack * Provided with some models. Product appearance depends on the model you purchased. Expre ...

  • Toshiba TECRA A50-A/W50-A - page 38

    LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Refer to Operating Basics , for details. Do not connect any cable other than a LAN cable to the LA ...

  • Toshiba TECRA A50-A/W50-A - page 39

    Battery pack The rechargeable lithium-ion battery pack provides power to the computer when the AC adaptor is not connected. For more detailed information on the use and operation of the battery pack please refer to the Battery section. Underside The following figures show the underside of the computer. You should ensure that the display is closed b ...

  • Toshiba TECRA A50-A/W50-A - page 40

    Only the TOSHIBA Hi-Speed Port Replicator III 180W is applicable with this Docking port for TECRA W50-A series. Only the TOSHIBA Hi-Speed Port Replicator III 180W or 120W is applicable with this Docking port for TECRA A50-A/Satellite PRO A50- A series. Do not attempt to use any other Port Replicator. Keep foreign objects out of the docking port. A ...

  • Toshiba TECRA A50-A/W50-A - page 41

    Figure 3-6 The front of the computer with the display panel open 1 6 13 13 15 11 7 8 9 9 7 8 2 3 4 2 6 A B 10 5 12 14 9 9 16 1. Wireless communication antennas (not shown)* 9. Touch Pad control buttons 2. Microphone* 10. Power button 3. Web Camera LED* 11. Keyboard 4. Web Camera* 12. Touch Pad 5. Display screen 13. AccuPoint control button* 6. Disp ...

  • Toshiba TECRA A50-A/W50-A - page 42

    Microphone The built-in microphone allows you to import and record sounds for your application - please refer to the Sound System and Video mode section for more information. Web Camera LED The Web Camera LED glows when the Web Camera is operating. Web Camera Web Camera is a device that allows you to record video or take photographs with your compu ...

  • Toshiba TECRA A50-A/W50-A - page 43

    eco indicator Double tap this indicator to launch the TOSHIBA eco Utility. Touch Pad control buttons The two buttons below the Touch Pad are used like the buttons on a standard mouse - press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right button to display a menu or other functi ...

  • Toshiba TECRA A50-A/W50-A - page 44

    NFC (Near Field Communication) detection area NFC (Near Field Communication) initiates interactions immediately between people and objects close the computer. NFC enables quick ad-hoc connections from PC to PC, or PC to device, through simple physical touch, without the pre-requisite of formal pairing. The interactions are intended to be quick, sim ...

  • Toshiba TECRA A50-A/W50-A - page 45

    Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the SSD may be vulnerable to data retention errors. Legal Footnote (HDD/SSD Capacity) For more information regarding HDD/SSD Capacity, please refer to the Legal Footnotes section. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and ca ...

  • Toshiba TECRA A50-A/W50-A - page 46

    sustained battery life. Switching is automatic and does not require the user to reboot the computer. In the Manage 3D Settings menu of NVIDIA Control Panel, you can change the global 3D settings and create overrides for specific programs. The overrides will be used automatically each time the specified programs are launched. Please use the default ...

  • Toshiba TECRA A50-A/W50-A - page 47

    The Display Power Saving Technology feature can be disabled in the Intel ® HD Graphics Control Panel/Intel ® Graphics and Media Control Panel. You can access this control panel in the following way: Right-click on the desktop and click Graphics Properties... In Intel ® HD Graphics Control Panel: 1. Click Power and select On battery . 2. Click Of ...

  • Toshiba TECRA A50-A/W50-A - page 48

    When Intel ® Rapid Start Technology is enabled, Wake-up on LAN, Wake-up on USB or Wake-up from Sleep Mode automatically functions are not available when the computer has been switched from Sleep Mode to Hibernation Mode. The Windows cannot be restored normally if the battery is exhausted when the computer is moving from Sleep Mode to Hibernation M ...

  • Toshiba TECRA A50-A/W50-A - page 49

    Power on Power off (no operation) AC adaptor not connected Remaining battery capacity is above low battery trigger point • Operates • LED: off Remaining battery capacity is below low battery trigger point • Operates • LED: flashes orange Remaining battery capacity is exhausted Computer shuts down DC IN/Battery indicator Check the DC IN/Batt ...

  • Toshiba TECRA A50-A/W50-A - page 50

    Power indicator Check the Power indicator to determine the power status of the computer - the following indicator conditions should be noted: Green Indicates power is being supplied to the computer and the computer is turned on. Flashing Orange Indicates that the computer is in Sleep Mode and that there is sufficient power available (AC adaptor or ...

  • Toshiba TECRA A50-A/W50-A - page 51

    Chapter 4 Operating Basics This chapter describes the basic operations of your computer, and highlights the precautions that should be taken when using it. Using the Touch Pad The Touch Pad located in the palm rest may support the following gestures: Tap Simply tap your finger on the Touch Pad to act on items on the screen. (Similar to left-click) ...

  • Toshiba TECRA A50-A/W50-A - page 52

    Keyboard indicator The following figure shows the position of the CAPS LOCK indicator and NUM LOCK indicator which show the following conditions: When the CAPS LOCK indicator glows, the keyboard will produce capitals when any letter is typed. When the NUM LOCK indicator glows, the ten key allows you to enter numbers. Figure 4-1 Keypad indicator 1 2 ...

  • Toshiba TECRA A50-A/W50-A - page 53

    Output Pressing FN + F5 changes the active display device. To use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device. Brightness Down Pressing FN + F6 decreases the computer's display panel brightness in individual steps. Brightness Up Pressing FN + F7 increases ...

  • Toshiba TECRA A50-A/W50-A - page 54

    3. Press the function key repeatedly to cycle through the available options and release the FN key when the desired option is selected. You can also click the desired option. Special function mode 1. Press the function key repeatedly to cycle through the available options and release it when the desired option is selected. For more information, ple ...

  • Toshiba TECRA A50-A/W50-A - page 55

    Strong stress is applied to the AccuPoint. If an error message appears, reboot the computer. If an error message does not appear, wait a moment for the pointer to stop, then continue operation. Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use. The spare AccuPoint cap is supplied with some models. ...

  • Toshiba TECRA A50-A/W50-A - page 56

    How to Swipe your Finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you until the sensor surface becomes visible. In performing t ...

  • Toshiba TECRA A50-A/W50-A - page 57

    Do not paste stickers or write on the sensor. Do not touch the sensor with a finger or any other object which may have a build-up of static electricity on it. Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition. Wash and dry your hands thoroughly. Remove static electricity ...

  • Toshiba TECRA A50-A/W50-A - page 58

    You can back up the fingerprint data or the information registered to Automatic password input in IE. Please use Import/Export in TOSHIBA Fingerprint Utility main menu. Please also refer to the fingerprint utility Help file for more information by clicking ? in TOSHIBA Fingerprint Utility main menu. Fingerprint utility limitations TOSHIBA does not ...

  • Toshiba TECRA A50-A/W50-A - page 59

    6. Swipe four times with the same finger. If scanning of fingerprint succeeds, "Enrollment succeeded! Do you want to save this fingerprint?" message box will appear. Click OK . 7. The following message will be displayed: "It’s strongly recommended you enroll one more fingerprint.". Click OK and repeat Step 3, 4, 5 and 6 with a ...

  • Toshiba TECRA A50-A/W50-A - page 60

    Windows Logon via Fingerprint Authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows. This is useful especially when many users are using the PCs, as user selection can be skipped. Fingerprint Authentication Procedure 1. Start up the computer. 2. The Logon Authorization screen ...

  • Toshiba TECRA A50-A/W50-A - page 61

    Overview about Fingerprint Single Sign-On feature This is a feature that allows the user to complete the authentication for both the User/BIOS Password (and, if applicable, the HDD/SSD Password) and logging onto Windows using only one fingerprint authentication when booting up. It is necessary to register the User/BIOS Password and Windows Logon Pa ...

  • Toshiba TECRA A50-A/W50-A - page 62

    Formats The drives support the following formats. DVD Super Multi drive The drive supports the following formats: CD-ROM, DVD-ROM, DVD- Video, CD-DA, CD-Text, Photo CD™ (single/multi-session), CD-ROM Mode 1/Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD- EXTRA), Addressing Method 2, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD-R DL (Forma ...

  • Toshiba TECRA A50-A/W50-A - page 63

    3. Lay the disc, label side up, in the disc tray. Figure 4-5 Inserting a disc 1 1. Laser lens When the disc tray is fully opened, the edge of the computer will cover the disc tray slightly. Therefore, you will need to turn the disc at an angle when you place it in the disc tray. After seating the disc, however, make sure it lies flat. Do not touch ...

  • Toshiba TECRA A50-A/W50-A - page 64

    When the disc tray pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open. 2. The disc extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the disc. 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove di ...

  • Toshiba TECRA A50-A/W50-A - page 65

    Blu-ray™ discs BD-R, BD-R DL discs can be written only once. The recorded data cannot be erased or changed. BD-RE, BD-RE DL discs can be recorded more than once. Writing discs You can use the DVD Super Multi drive to write data to either CD-R, CD- RW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW or DVD-RAM discs. You can use the Blu-ray™ Wr ...

  • Toshiba TECRA A50-A/W50-A - page 66

    Before writing or rewriting Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of disc media, however, it must be noted that disc quality can affect write or rewrite success rates. Please also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc. CD-R: TAIYO YU ...

  • Toshiba TECRA A50-A/W50-A - page 67

    BD-RE: Panasonic Corporation BD-RE DL: Panasonic Corporation BD-R TL: TDK. SHARP BD-RE TL: Panasonic Corporation Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable. Disc created in DVD-R DL format4 (Layer Jump Recording) cannot be read. When writing or rewriting Please observe the following points while you write or rewrite dat ...

  • Toshiba TECRA A50-A/W50-A - page 68

    Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains or cars. In addition, do not use the computer on an unstable surface such as a stand. Keep mobile phones and other wireless communication devices away from the computer. TOSHIBA Disc Creator Please be aware of the following limitations when you use t ...

  • Toshiba TECRA A50-A/W50-A - page 69

    When you back up a DVD disc, be sure that the source drive supports recording to DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL or DVD+RW media - if this is not the case then the source disc might not be backed up correctly. When you back up a DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL or DVD+RW disc, be sure to use the same type of disc. You cannot partia ...

  • Toshiba TECRA A50-A/W50-A - page 70

    Use DVD-Video discs with a region code which is either "the same as the factory default setting" (if applicable) or "ALL". Do not playback video while watching or recording television programs using other applications. Doing so may cause video playback or television program recording errors. In addition, if prescheduled recordin ...

  • Toshiba TECRA A50-A/W50-A - page 71

    Display Devices & Audio If the video image is not displayed on an external display or television, stop the TOSHIBA VIDEO PLAYER, and change the screen resolution. To change the screen resolution, click Start -> Control Panel -> Appearance and Personalization -> Display -> Adjust resolution . However, video cannot be output to some e ...

  • Toshiba TECRA A50-A/W50-A - page 72

    Notes on Use This software can only be used on Windows operating system. Playback of high bit rate content may cause frame dropping, audio skipping or decrease in computer performance. Close all other applications before playing back video. Do not open any other applications or carry out any other operations during video playback. Do not switch to ...

  • Toshiba TECRA A50-A/W50-A - page 73

    The Blu-ray Disc™ movie can be played only on internal LCD displays or external devices connected via an HDMI output. In Clone mode (Dual View), TOSHIBA Blu-ray Disc Player may not function properly. This product does not play HD DVD discs. Blu-ray™ discs with high definition content are required for HD viewing. This software can only playback ...

  • Toshiba TECRA A50-A/W50-A - page 74

    Battery pack When the AC adaptor is not connected, the computer's main power source is a removable lithium ion battery pack, also referred to in this manual as the main battery. You can purchase additional battery packs for extended use of the computer away from an AC power source although you should not change the battery pack while the AC ad ...

  • Toshiba TECRA A50-A/W50-A - page 75

    Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened. Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor. Never remove the b ...

  • Toshiba TECRA A50-A/W50-A - page 76

    Battery type Power off Power on RTC Battery (Normal) Doesn’t charge about 10 hours RTC Battery (High Capacity) Doesn’t charge about 20 hours (TECRA A50-A/ Satellite PRO A50-A) about 18 hours (TECRA W50-A) Please be aware that the charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how yo ...

  • Toshiba TECRA A50-A/W50-A - page 77

    You should wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. This is because the computer needs this time to check the battery's remaining capacity and then calculate the remaining operating time, based on this together with the current power consumption. Please be aware that the actu ...

  • Toshiba TECRA A50-A/W50-A - page 78

    Battery type Sleep Mode Shut Down Mode Battery pack (24Wh, 3 cell) about 2 days about 50 days Battery pack (48Wh, 6 cell) about 5 days about 100 days Battery pack (67Wh, 6 cell) about 6 days about 135 days (TECRA A50-A/ Satellite PRO A50-A) about 80 days (TECRA W50-A) RTC Battery (Normal) about 30 days about 30 days RTC Battery (High Capacity) abou ...

  • Toshiba TECRA A50-A/W50-A - page 79

    The operating life of the battery pack will gradually reduce through repeated charging and discharging, and will need to be replaced when it reaches the end of its operating life. In addition to this, you might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source for an extend ...

  • Toshiba TECRA A50-A/W50-A - page 80

    Figure 4-7 Releasing the battery pack 1 2 3 3 1 2 1. Battery lock 3. Battery pack 2. Battery release latch Installing the battery pack To install a battery pack, follow the steps as detailed below: Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery rel ...

  • Toshiba TECRA A50-A/W50-A - page 81

    4. Turn the computer upside down and remove the battery pack (refer to Replacing the battery pack section, if required). 5. Locate the SIM card slot. 6. Slide your SIM card into the SIM card slot with the metal connectors facing up. Figure 4-8 Installing the SIM Card 2 1 1. SIM Card 2. SIM Card Slot Product appearance depends on the model you purch ...

  • Toshiba TECRA A50-A/W50-A - page 82

    6. Press the SIM Card gently and release it. It pops out of the slot. Figure 4-9 Removing the SIM Card 1 1. SIM Card Product appearance depends on the model you purchased. 7. Grasp the SIM Card and remove it. 8. Install the battery pack and turn your computer over. LAN The computer may have built-in support for Ethernet LAN (10 megabits per second, ...

  • Toshiba TECRA A50-A/W50-A - page 83

    If you are using Fast Ethernet LAN (100 megabits per second, 100BASE- TX), be sure to connect with a CAT5 cable or higher. You cannot use a CAT3 cable. If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher cable. Connecting the LAN cable To connect the LAN cable, follow the steps as detailed below: ...

  • Toshiba TECRA A50-A/W50-A - page 84

    You should place a mat beneath the computer in order to prevent the computer's lid from becoming scratched or damaged when you are installing/replacing the memory module. In this instance you should avoid mats that are made of materials that hold or generate static electricity. When installing or removing a memory module, you must ensure that ...

  • Toshiba TECRA A50-A/W50-A - page 85

    6. Slide your fingernail or a thin object under the cover and lift it off. Figure 4-11 Removing the memory module cover 1 1 2 1. Screw 2. Memory module cover Product appearance depends on the model you purchased. 7. Follow this procedure to install or remove a memory module: Install procedure: Align the notch of the memory module with that of the m ...

  • Toshiba TECRA A50-A/W50-A - page 86

    Figure 4-12 Seating the memory module 3 2 1 2 3 1 3 2 1 1. Notch 3. Slot A 2. Slot B Product appearance depends on the model you purchased. Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serio ...

  • Toshiba TECRA A50-A/W50-A - page 87

    Please also ensure that you hold the memory module along its left and right hand edges - the edges with the grooves in. Remove procedure: Push the latches away from the module in order to release it - a spring will force one end of the module up at an angle. And then grasp the module by its edges and remove it from the computer. Never allow metal o ...

  • Toshiba TECRA A50-A/W50-A - page 88

    Figure 4-13 Removing the memory module 2 1 1 1 1 2 1 1 1. Latches Product appearance depends on the model you purchased. 8. Seat the memory module cover in place and secure it with the screw. Take care to ensure that the memory module cover is firmly closed. Figure 4-14 Seating the memory module cover 2 2 1 1. Memory module cover 2. Screw Product a ...

  • Toshiba TECRA A50-A/W50-A - page 89

    9. Install the battery pack - refer to Replacing the battery pack section, if required. 10. Turn your computer over. 11. Turn the computer on and make sure the available memory is recognized - to confirmed it, click Start -> Control Panel -> System and Security -> System . Installing/Removing a memory module (Slot C/D) To install/remove a ...

  • Toshiba TECRA A50-A/W50-A - page 90

    7. Slip your fingernail or a thin object under the notch at the end of the keyboard brace and lift it up to release latches and remove the keyboard brace. Figure 4-16 Removing the Keyboard brace 1 1. keyboard brace Product appearance depends on the model you purchased. 8. Lift the top edge of the keyboard while releasing the latches, rotate it and ...

  • Toshiba TECRA A50-A/W50-A - page 91

    9. Loosen the screw securing the memory module cover in place - please note that the screw is attached to the cover in order to prevent it from being lost. Figure 4-17 Removing the memory module cover (1) 1 2 1. screw 2. Memory module cover Product appearance depends on the model you purchased. 10. Removing the memory module slot C/D cover. Figure ...

  • Toshiba TECRA A50-A/W50-A - page 92

    Figure 4-19 Installing the memory module 3 2 1 1 1. Notch 3. Slot D 2. Slot C Product appearance depends on the model you purchased. Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious inju ...

  • Toshiba TECRA A50-A/W50-A - page 93

    Figure 4-20 Removing the memory module 1 1 1 1 1. Latches Product appearance depends on the model you purchased. Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. Do not touch the ...

  • Toshiba TECRA A50-A/W50-A - page 94

    15. Close the display panel and turn the computer upside down. 16. Secure the KB screw on the underside of the computer. 17. Install the battery pack - refer to Replacing the battery pack section, if required. 18. Turn your computer over. 19. Turn the computer on and make sure the available memory is recognized - to confirmed it, click Start -> ...

  • Toshiba TECRA A50-A/W50-A - page 95

    protected material on another computer or other device, and you may not reproduce any copyrighted material except for your personal enjoyment. Below is a simple explanation for distinguishing SD memory cards from SDHC memory cards and SDXC memory cards. SD, SDHC and SDXC memory cards appear the same externally. However, the logo on memory cards is ...

  • Toshiba TECRA A50-A/W50-A - page 96

    Set the write-protect switch to the lock position, if you do not want to record data. Memory cards have a limited lifespan, so it is important to backup important data. Do not write to a card if the battery power is low. Low power could affect writing accuracy. Do not remove a card while read/write is in progress. For more details on using memory c ...

  • Toshiba TECRA A50-A/W50-A - page 97

    3. Press the memory media gently to ensure a firm connection is made. Figure 4-22 Inserting memory media 2 1 1. Memory media slot 2. Memory media Make sure the memory media is oriented properly before you insert it. If you insert the media in wrong direction, you may not be able to remove it. When inserting the memory media, do not touch the metal ...

  • Toshiba TECRA A50-A/W50-A - page 98

    connection and utilizes the PCI Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5Gbps. Inserting an ExpressCard The Windows hot-install feature allows you to insert ExpressCards while the computer is turned on. Do not insert an ExpressCard while the computer is in Sleep Mode or Hibernation Mode as ...

  • Toshiba TECRA A50-A/W50-A - page 99

    Smart Card A Smart Card is a credit card sized plastic card. An extremely thin integrated circuit (IC chip) is embedded into the card on which information can be recorded. These cards can be used for a wide variety of applications including telephone related and electronic monetary payments. This section contains information on the proper use of th ...

  • Toshiba TECRA A50-A/W50-A - page 100

    Before removing the Smart Card, confirm that the Smart Card is not working with any program or system. Be careful not to bend the Smart Card while removing it from the computer. 2. Point to Smart Card and click the left Touch Pad control button. 3. Grasp the Smart Card and remove it. External Display Your computer video capabilities can be enhanced ...

  • Toshiba TECRA A50-A/W50-A - page 101

    When displaying desktop on an external analog monitor, desktop is sometimes displayed on the center of the monitor with black bars around desktop (with small size). At that time, please read the manual of the monitor and set the display mode which is supporting at the monitor. Then it will be displayed with suitable size with correct aspect ratio. ...

  • Toshiba TECRA A50-A/W50-A - page 102

    The system is starting up. The system is shutting down. When you connect a television or external monitor to the HDMI port, the display output device is set to HDMI. When you unplug the HDMI cable and re-plug it, please wait at least 5 seconds before you re-plug the HDMI cable again. Settings for display video on HDMI To view video on the HDMI disp ...

  • Toshiba TECRA A50-A/W50-A - page 103

    To learn more details on how to complete the connection, please refer to the application help. Some copy protected media contents may not play on the external displays via Intel WiDi. Changing the external playback settings After one or more external displays are connected, the operating system can automatically detect, identify and setup the displ ...

  • Toshiba TECRA A50-A/W50-A - page 104

    When you use external display ports on the Port Replicator, some software may show different type of ports which you connected. When connecting an AC Adaptor to the Port Replicator, use only the AC Adaptor included with Port Replicator. Do not use the computer’s AC Adaptor. Refer to the Port Replicator’s User's Manual for more details. To ...

  • Toshiba TECRA A50-A/W50-A - page 105

    Press the Eject button on the port replicator. Click Start , select Undock from the Shut down options . Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar and select Eject Docking Station . To access the utility, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> TOSHIBA Docking Station Utility . ...

  • Toshiba TECRA A50-A/W50-A - page 106

    2. Remove the cap of the Serial port conversion cable. 3. Connect the Serial port conversion cable to your computer. Figure 4-27 Connecting the Serial Connector 2 1 1. Serial Connector 2. Serial port conversion cable Security lock A security lock enables you to anchor your computer to a desk or other heavy object in order to help prevent unauthoriz ...

  • Toshiba TECRA A50-A/W50-A - page 107

    Memory Kit DDR3 memory modules can easily be installed in the computer. The available option memory depends on TOSHIBA authorization. Universal AC Adaptor If you frequently use your computer at more than one site, it may be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to always carry the adapto ...

  • Toshiba TECRA A50-A/W50-A - page 108

    Audio Enhancements In order to apply the sound effects for your current speaker, follow the steps below. 1. Right click on the Speakers icon on the Taskbar, and then select Playback devices from the sub menu. 2. Select Speakers , and click Properties . 3. On the Enhancements tab select the sound effects you would like, and click Apply . DTS Studio ...

  • Toshiba TECRA A50-A/W50-A - page 109

    Information Click the Information button to view hardware information, software information, and language setting. Power Management The audio controller in your computer can be turned off when the audio function is not used. To adjust the configuration of audio power management, click the Power Management button . When audio power management is ena ...

  • Toshiba TECRA A50-A/W50-A - page 110

    Chapter 5 Utilities and Advanced Usage This chapter describes the utilities and special features of this computer, and the advanced usage of some utilities. Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, you may refe ...

  • Toshiba TECRA A50-A/W50-A - page 111

    The efficient performance might not be expected with multiple user accounts registered. Only startup from built-in HDD/SSD supports Hi-Speed Start Mode. When system needs to be restarted because of Windows update, drivers update or applications installation, please Shut down or Restart accordingly. If not, those changes will not be reflected to the ...

  • Toshiba TECRA A50-A/W50-A - page 112

    Bluetooth Stack for Windows by Toshiba This software enables communication between the computer and external Bluetooth devices such as printers and mobile phones. Bluetooth functions cannot be used in models that do not have a Bluetooth module installed. TOSHIBA eco Utility This computer is equipped with "eco mode". This mode slightly low ...

  • Toshiba TECRA A50-A/W50-A - page 113

    TOSHIBA Sleep Utility This utility is able to either enable or disable the following function: Sleep and Charge: By connecting to the USB port, devices such as digital audio players are able to charge, even when the computer is in Standby/Sleep Mode, Hibernation Mode or shutdown state. To access this utility, click Start -> All Programs -> TO ...

  • Toshiba TECRA A50-A/W50-A - page 114

    Trusted Platform Module (TPM) The TPM (Trusted Platform Module) is a security encryption device for the HDD/SSD. You can install TPM by clicking Infineon TPM Software Professional Package from Applications and Drivers list. You can launch TOSHIBA Setup Utility to change the TPM settings in the Security tab. Please refer to TOSHIBA Setup Utility sec ...

  • Toshiba TECRA A50-A/W50-A - page 115

    Intelligent power supply *1 A microprocessor in the computer's intelligent power supply detects the battery's charge, automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor. This can be specified in the Power Options. Battery save m ...

  • Toshiba TECRA A50-A/W50-A - page 116

    Heat dispersal *1 To protect against overheating, the processor is equipped with an internal temperature sensor which activates a cooling fan or lowers the processing speed if the computer's internal temperature rises to a certain level. You are able to select whether to control this temperature by either turning on the fan first, then if nece ...

  • Toshiba TECRA A50-A/W50-A - page 117

    When Sleep and Charge function is enabled, USB bus power (DC5V) will be supplied to compatible ports even when the power of the computer is turned OFF. USB bus power (DC5V) is similarly supplied to the external devices which are connected to the compatible ports. However, some external devices cannot be charged solely by supplying USB bus power (DC ...

  • Toshiba TECRA A50-A/W50-A - page 118

    Always use the USB cable that was included with your USB device. Enable under Battery Mode This option can be used to enable/disable sleep and charge under battery mode. It also displays the remaining battery capacity. Move the slider to enable or disable this function. Enabled Enables Sleep and Charge function under battery mode. Disabled Enables ...

  • Toshiba TECRA A50-A/W50-A - page 119

    case, use a USB port without "USB Sleep and Charge function" or disable both “System ON CDP Charge Mode” and “USB Sleep and Charge function”. TOSHIBA Password utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set by the TOSHIBA Password Utility function are different from ...

  • Toshiba TECRA A50-A/W50-A - page 120

    Owner String (text box) You can use this box to associate text with the password. After you enter text, click Apply or OK . When the computer is started, this text will be displayed together with the prompt asking you to enter a password. You can launch the BIOS setup utility to set, change or delete the HDD Password or HDD Master Password. If you ...

  • Toshiba TECRA A50-A/W50-A - page 121

    1. Turn on the power as described in the Getting Started section. The following message will appear in the screen: Password= At this point, the function keys do not work. They will function after you enter the password. 2. Enter the Password. 3. Press ENTER . If you enter the password incorrectly three times in a row, or if you don’t enter the pa ...

  • Toshiba TECRA A50-A/W50-A - page 122

    LAN—Allows you to set conditions for LAN Advanced—Allows you to set conditions for a specific device or function The settings or options explained here may vary depending on the model you purchased. After you changed the settings, a dialog box may appear to prompt you that the changes will take effect after the computer is restarted. Make sure ...

  • Toshiba TECRA A50-A/W50-A - page 123

    Starting the TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor can be started using the following methods: Click Start -> All Programs -> TOSHIBA -> Support & Recovery -> PC Health Monitor . Click the icon ( ) in the notification area, then click the " Enable PC Health Monitor... " message the first time you run the ...

  • Toshiba TECRA A50-A/W50-A - page 124

    Taskbar icon Normal TOSHIBA HDD Protection is enabled. Protection TOSHIBA HDD Protection is active. The hard disk drive head is in a safe position. OFF TOSHIBA HDD Protection is disabled. TOSHIBA HDD Protection Properties You can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, cl ...

  • Toshiba TECRA A50-A/W50-A - page 125

    3D Viewer This feature displays a 3D object on the screen which moves in according to tilting or vibration of the computer. When the TOSHIBA HDD Protection detects computer vibration the Hard Disk Drive head is parked and the 3D object disk rotation will stop. When the head is un-parked the disk will begin to rotate again. The 3D Viewer can be star ...

  • Toshiba TECRA A50-A/W50-A - page 126

    You can also create recovery media and restore the system. The following items will be described in this section: System Recovery Options Creating Recovery Media Restoring the pre-installed software from your created Recovery Media Restoring the pre-installed software from the Recovery Hard Disk Drive System Recovery Options The System Recovery Opt ...

  • Toshiba TECRA A50-A/W50-A - page 127

    Do not use utilities, including those intended to enhance Hard Disk Drive access speed. They may cause unstable operation and damage data. Do not shut down/log off or Sleep/Hibernate while writing or rewriting the media. Set the computer on a level surface and avoid places subjected to vibrations such as airplanes, trains, or cars. Do not use on an ...

  • Toshiba TECRA A50-A/W50-A - page 128

    3. While holding down F12 key on the keyboard, turn on your computer - when the TOSHIBA Leading Innovation >>> logo screen appears, release the F12 key. 4. Use the up and down cursor key to select the appropriate option from the menu according to your actual recovery media. 5. A menu will be displayed from which you should follow the on-sc ...

  • Toshiba TECRA A50-A/W50-A - page 129

    Chapter 6 Troubleshooting TOSHIBA has designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place. Problem so ...

  • Toshiba TECRA A50-A/W50-A - page 130

    Check all cables to ensure they are correctly and firmly attached to the computer - loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins. Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them in a permanent error log - this ...

  • Toshiba TECRA A50-A/W50-A - page 131

    Hardware If you cannot find a software problem, you should then check the setup and configuration of your hardware. First run through the items in the preliminary checklist as described previously then, if you still cannot correct the problem, try to identify the source - the next section provides checklists for individual components and peripheral ...

  • Toshiba TECRA A50-A/W50-A - page 132

    If you are using the AC adaptor, check that the wall outlet is working by plugging in another device, such as a lamp. Verify that the computer is on by looking at the Power indicator. If the indicator is glowing, the computer is on. Also, try turning the computer off and then on. If you are using an AC adaptor, verify that the computer is receiving ...

  • Toshiba TECRA A50-A/W50-A - page 133

    AC power If you have trouble turning on the computer with the AC adaptor connected you should check the status of the DC IN/Battery indicator. Please refer to the Power Condition Descriptions section for further information. Problem Procedure AC adaptor doesn’t power the computer Check the connections to make sure that the power cord/adaptor is f ...

  • Toshiba TECRA A50-A/W50-A - page 134

    Problem Procedure Battery doesn’t charge when the AC adaptor is attached. If the battery is completely discharged, it will not begin charging immediately, in these instances you should wait a few minutes before trying again. If the battery still does not charge, you should check that the power outlet the AC adaptor is connected to its supplying p ...

  • Toshiba TECRA A50-A/W50-A - page 135

    Real Time Clock Problem Procedure The BIOS setting and system date/ time are lost. The charge in the Real Time Clock (RTC) battery has run out - you will need to set the date and time in the TOSHIBA Setup Utility by using the following steps: 1. Press and hold the F2 key, and then turn on the computer - the TOSHIBA Setup Utility will load. 2. Set t ...

  • Toshiba TECRA A50-A/W50-A - page 136

    HDD/SSD Problem Procedure Computer does not boot from HDD/SSD Check to see whether there is a disc in the optical disc drive - if so remove it and try to start the computer again. If this has no effect, check the Boot Setting within the TOSHIBA HWSetup. Slow performance The files on the HDD/SSD may be fragmented - in this instance you should run th ...

  • Toshiba TECRA A50-A/W50-A - page 137

    Problem Procedure Memory media card error occurs Remove the memory media card from the computer and then reinsert it in order to ensure it is firmly connected. If the problem persists, then you should refer to the documentation supplied with your memory media card for further information. You cannot write to a memory media card Remove the memory me ...

  • Toshiba TECRA A50-A/W50-A - page 138

    Problem Procedure The on-screen pointer moves too fast or too slow In this instance, you should initially try changing the speed setting within the Mouse Control utility. 1. To access this utility, click Start -> Control Panel -> Hardware and Sound -> Mouse . 2. Within the Mouse Properties window, click the Pointer Options tab. 3. Set the ...

  • Toshiba TECRA A50-A/W50-A - page 139

    Problem Procedure The on-screen pointer moves erratically The elements of the mouse responsible for detecting movement might be dirty - please refer to the documentation supplied with the mouse for instructions on how to clean it. If you are still unable to resolve the problem, contact TOSHIBA Support. USB device In addition to the information in t ...

  • Toshiba TECRA A50-A/W50-A - page 140

    Problem Procedure I cannot use the Sleep and Charge function. Sleep and Charge function may be disabled. Enable the Sleep and Charge function in the TOSHIBA System Settings. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons. When this happens, disc ...

  • Toshiba TECRA A50-A/W50-A - page 141

    Problem Procedure The "USB Wakeup function" does not work. When "System ON CDP Charge Mode" or "USB Sleep and Charge function" is enabled, the "USB WakeUp" function does not work for ports that support the Sleep and Charge function. In that case, use an USB port that does not have the USB Sleep and Charge fun ...

  • Toshiba TECRA A50-A/W50-A - page 142

    Problem Procedure Monitor does not turn on After confirming that the monitor's power switch is on, you should check the connections to make sure that the power cord/adaptor is firmly connected to the monitor and to a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press the function ...

  • Toshiba TECRA A50-A/W50-A - page 143

    Problem Procedure Wake-up on LAN does not work Make sure the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off. If problems persist, consult your LAN administrator. Wireless LAN Problem Procedure Cannot access Wireless LAN Make sure the computer's Wireless communication function is on. If problems ...

  • Toshiba TECRA A50-A/W50-A - page 144

    If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions and consider calling the software company's technical support department for assistance. Consult the reseller or dealer from where you purchased your computer and/or software - they are your best resource for curre ...

  • Toshiba TECRA A50-A/W50-A - page 145

    Chapter 7 Appendix Specifications This section summarizes the computer’s technical specifications. Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body. The physical dimensions may vary depending on the model you purchased. Size Approximately 380.9 (w) x 253.9 (d) x 27.8/34.9 (h) millimeters (n ...

  • Toshiba TECRA A50-A/W50-A - page 146

    External RGB monitor port pin assignment 6 10 1 5 15 1 1 Pin Signal Name Description I/O 1 CRV Red Video Signal O 2 CGV Green Video Signal O 3 CBV Blue Video Signal O 4 Reserved Reserved 5 GND Ground 6 GND Ground 7 GND Ground 8 GND Ground 9 +5V Power Supply 10 GND Ground 11 Reserved Reserved 12 SDA Data Signal I/O 13 HSYNC Horizontal Sync Signal O ...

  • Toshiba TECRA A50-A/W50-A - page 147

    Certification agencies China: CQC U.S. and Canada: UL listed and CSA certified No. 18 AWG, Type SVT or SPT-2 Australia: AS Japan: DENANHO Europe: Austria: OVE Italy: IMQ Belgium: CEBEC The Netherlands: KEMA Denmark: DEMKO Norway: NEMKO Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: SEV Germany: VDE United Kingdom: BSI In Europe, two conduct ...

  • Toshiba TECRA A50-A/W50-A - page 148

    Australia AS approved Europe Approved by the appropriate agency Canada CSA approved China CCC approved Information for Wireless Devices Wireless Technology Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is complian ...

  • Toshiba TECRA A50-A/W50-A - page 149

    Please visit http://www.pc.support.global.toshiba.com, if you have any questions about using Wireless LAN or Bluetooth Module. In Europe visit http://www.toshiba-europe.com/computers/tnt/bluetooth.htm Wireless Devices and your health Wireless products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitte ...

  • Toshiba TECRA A50-A/W50-A - page 150

    Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury. It may not be possible to make a network connection to a specified network name using the ad hoc network functi ...

  • Toshiba TECRA A50-A/W50-A - page 151

    The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances. The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials. Range is also impacted due to "obstacles" ...

  • Toshiba TECRA A50-A/W50-A - page 152

    This Bluetooth Stack is based on the Bluetooth specification, depending on the model you purchased. However, TOSHIBA cannot confirm the compatibility between any computing products and/or other electronic devices that use Bluetooth, other than TOSHIBA notebook computers. Release Notes related to the Bluetooth Stack for Windows by TOSHIBA 1. Fax app ...

  • Toshiba TECRA A50-A/W50-A - page 153

    Norway: Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Alesund. Russian Federation: - Only for indoor applications. Restrictions for Use of 5150-5350MHz Frequencies in Europe Italy: - For private use, a general authorization is required if WAS/ RLAN’s are used outside own premis ...

  • Toshiba TECRA A50-A/W50-A - page 154

    Russian Federation: Limited e.i.r.p 100mW. Permitted to use only for indoor applications, closed industrial and warehouse areas, and on board aircraft. 1. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight. 2. Permitted to use for public wireless access lo ...

  • Toshiba TECRA A50-A/W50-A - page 155

    The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met. USA-Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide rea ...

  • Toshiba TECRA A50-A/W50-A - page 156

    Article 14 The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act. The low power radio-fre ...

  • Toshiba TECRA A50-A/W50-A - page 157

    1. 2.4 : This equipment uses a frequency of 2.4GHz. 2. DS : This equipment uses DS-SS modulation. 3. OF : This equipment uses OFDM modulation. 4. 4 : The interference range of this equipment is less than 40m. 5. : This equipment uses a frequency bandwidth from 2,400MHz to 2,483.5MHz. It is possible to avoid the band of mobile object identification ...

  • Toshiba TECRA A50-A/W50-A - page 158

    Intel ® Centrino ® Wireless-N 2230 Wireless LAN and Bluetooth The Name of the radio equipment: 2230BNHMW DSP Research, Inc. Approval Number: D111287003 Intel ® Centrino ® Advanced-N 6235 a/b/g/n (a/b/g) Wireless LAN and Bluetooth The Name of the radio equipment: 6235ANHMW DSP Research, Inc. Approval Number: D111083003 The following restrictions ...

  • Toshiba TECRA A50-A/W50-A - page 159

    your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis. CPU Central Processing Unit (CPU) Performance Legal Footnotes. CPU performance in your computer product may vary from specifications under the following conditions: use of certain external peripheral prod ...

  • Toshiba TECRA A50-A/W50-A - page 160

    Certain 32-bit device drivers and/or applications may not be compatible with a 64-bit CPU/operating system and therefore may not function properly. Memory (Main System) Part of the main system memory may be used by the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activi ...

  • Toshiba TECRA A50-A/W50-A - page 161

    be less if the product includes one or more pre-installed operating systems, such as Microsoft Operating System and/or pre-installed software applications, or media content. Actual formatted capacity may vary. LCD Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrins ...

  • Toshiba TECRA A50-A/W50-A - page 162

    ASCII: American Standard Code for Information Interchange BIOS: Basic Input/output System BD-ROM: Blu-ray Disc Read-only Memory bps: bits per second CD: Compact Disc CD-ROM: Compact Disc Read-only Memory CD-RW: Compact Disc-rewritable CMOS: Complementary Metal-oxide Semiconductor CPU: Central Processing Unit DC: Direct Current DDR: Double Data Rate ...

  • Toshiba TECRA A50-A/W50-A - page 163

    ISP: Internet Service Provider KB: kilobyte LAN: Local Area Network LCD: Liquid Crystal Display LED: Light Emitting Diode MB: megabyte MBps: megabytes per second MMC: Multi Media Card OCR: Optical Character Recognition (Reader) PC: Personal Computer PCI: Peripheral Component Interconnect PCMCIA: Personal Computer Memory Card International Associati ...

  • Toshiba TECRA A50-A/W50-A - page 164

    Index A AC adaptor additional 4-57 connecting 2-3 DC IN 19V jack 3-6 B Battery extending life 4-28 monitoring capacity 4-26 real time clock 3-13, 4-24 save mode 5-6 types 4-23 Battery indicator Battery pack replacing 4-28 Bluetooth Bluetooth Stack for Windows by Toshiba 5-3 C Cleaning the computer 1-17 Cooling vents 3-3, 3-8 D DC IN/Battery indicat ...

  • Toshiba TECRA A50-A/W50-A - page 165

    FN + F3 (Sleep) 4-2 FN + F4 (Hibernate) 4-2 FN + F5 (Output) 4-3 FN + F6 (Brightness Down) 4-3 FN + F7 (Brightness Up) 4-3 FN + F8 (Wireless) 4-3 FN + F9 (Touch Pad) 4-3 FN + space (Zoom) 4-3 FN + TAB (ODD) H Hard disk drive automatic power off 5-5 HDD Protection 5-14 HWSetup accessing 5-12 window 5-12 K Keyboard Function keys F1...F12 4-2 problems ...

  • Toshiba TECRA A50-A/W50-A - page 166

    Problems AC power 6-5 Analyzing the problem 6-2 Battery 6-5 Dual Pointing device 6-9 External monitor 6-13 Hardware and system checklist 6-4 HDD 6-8 Internal display panel 6-7 Keyboard 6-7 Memory Media Card 6-8 Overheating power down 6-4 Power 6-4 Real Time Clock 6-7 Sound system 6-13 TOSHIBA support 6-15 Touch Pad 6-9 USB device 6-11 USB mouse 6-1 ...

Manufacturer Toshiba Category GPS Receiver

Documents that we receive from a manufacturer of a Toshiba TECRA A50-A/W50-A can be divided into several groups. They are, among others:
- Toshiba technical drawings
- TECRA A50-A/W50-A manuals
- Toshiba product data sheets
- information booklets
- or energy labels Toshiba TECRA A50-A/W50-A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Toshiba TECRA A50-A/W50-A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Toshiba TECRA A50-A/W50-A, service manual, brief instructions and user manuals Toshiba TECRA A50-A/W50-A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Toshiba TECRA A50-A/W50-A.

Similar manuals

A complete manual for the device Toshiba TECRA A50-A/W50-A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Toshiba TECRA A50-A/W50-A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Toshiba TECRA A50-A/W50-A.

A complete Toshiba manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Toshiba TECRA A50-A/W50-A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Toshiba TECRA A50-A/W50-A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Toshiba TECRA A50-A/W50-A, that we can find in the current document
3. Tips how to use the basic functions of the device Toshiba TECRA A50-A/W50-A - which should help us in our first steps of using Toshiba TECRA A50-A/W50-A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Toshiba TECRA A50-A/W50-A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Toshiba TECRA A50-A/W50-A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Toshiba TECRA A50-A/W50-A?

Use the form below

If you did not solve your problem by using a manual Toshiba TECRA A50-A/W50-A, ask a question using the form below. If a user had a similar problem with Toshiba TECRA A50-A/W50-A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)