Manual Skil 5400

36 pages 0.77 mb
Download

Go to site of 36

Summary
  • Skil 5400 - page 1

    IMPORTANT: IMPORTANT : IMPORTANTE: Read Before Using Lire avant usage Leer antes de usar Operating/Safety Instructions Consignes de fonctionnement/sécurité Instrucciones de funcionamiento y seguridad 5400 5450 5500 5600 5650 5700 For English Parlez-vous français? ¿Habla español? See page 2 Voir page 13 Ver página 24 1-877-SKIL999 (1-877-754-5 ...

  • Skil 5400 - page 2

    Read and understand all instructions . Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS -2 - Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in t ...

  • Skil 5400 - page 3

    -3- Safety Rules for Circular Saws Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use tool if switch does not turn it “ON” or “OFF”. Any tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect th ...

  • Skil 5400 - page 4

    Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released. NEVER hold piece being cut in your hands or across your leg. It is im ...

  • Skil 5400 - page 5

    or KICKBACK from the workpiece as the saw is restarted. Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel. See “Cutting Large Sheets” in this manual. Do not use dull ...

  • Skil 5400 - page 6

    -6- IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Name Designation/Explanation V Volts Voltage (potential) A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power kg Kilogra ...

  • Skil 5400 - page 7

    -7- Functional Description and Specifications Disconnect the plug from the power source before making any assembly, adjustments or changing accessories . Such preventive safety measures reduce the risk of starting the tool accidentally. ! WARNING FIG. 1 LOWER GUARD FOOT LOWER GUARD LIFT LEVER AUXILIARY HANDLE ADJUSTABLE LINE GUIDE (Models 5450 5500 ...

  • Skil 5400 - page 8

    -8- Assembly ATTACHING THE BLADE Disconnect the plug from the power source before making any assembly, adjustments or changing accessories . Such preventive safety measures reduce the risk of starting the tool accidentally. 1. Turn BLADE STUD with wrench provided counter-clockwise and remove BLADE STUD and OUTER WASHER (Fig. 2). If the shaft moves ...

  • Skil 5400 - page 9

    -9- Disconnect plug from power source. Loosen the depth adjustment lever located between the guard and handle of saw. Hold the foot down with one hand and raise or lower saw by the handle. Tighten lever at the depth setting desired. Check desired depth (Fig. 3). Not more than one tooth length of the blade should extend below the material to be cut, ...

  • Skil 5400 - page 10

    -10- ADJUSTABLE LINE GUIDE (Models 5450 5500, 5600, 5650, & 5700 only) For a straight 90° cut you can use the left or right side of notch in the foot. For 45° bevel cuts, use the right side (Fig 9). The guide can be adjusted to allow for variation in blade thicknesses for whichever side of the blade the user would prefer to cut the line on. T ...

  • Skil 5400 - page 11

    -11- POCKET CUTS Disconnect the plug from the power source before making adjustments. Set depth adjust- ment according to material to be cut. Tilt saw forward with cutting guide notch lined up with the line you’ve drawn. Raise the lower guard, using lift lever and hold the saw by the front and rear handles (Fig. 10). With the blade just clearing ...

  • Skil 5400 - page 12

    -12- Accessories Service Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service, inc lud in g replacement of the line of cut indicator bulb, be performed by a Skil Factory Service Center or Authorized Skil Service Stati ...

  • Skil 5400 - page 13

    -13- Vous devez lire et comprendre toutes les instructions. Le non-respect, même partiel, des instructions ci-après entraîne un risque de choc életrique, d'incendie et/ou de blessures graves. CONSERVEZ CES INSTRUCTIONS AVERTISSEMENT ! Aire de travail Veillez à ce que l'aire de travail soit propre et bien éclairée. Le désordre et l ...

  • Skil 5400 - page 14

    -14- N'utilisez pas un outil si son interrupteur est bloqué. Un outil que vous ne pouvez pas commander par son interrupteur est dangereux et doit être réparé. Débranchez la fiche de l'outil avant d'effectuer un réglage, de changer d'accessoire oude ranger l'outil. De telles mesures préventives de sécurité réduisen ...

  • Skil 5400 - page 15

    Assurez-vous toujours que le garde inférieur couvre la lame avant de déposer la scie sur l'établi ou le plancher. Une lame non protégée, qui continue à marcher par inertie, fera reculer la scie, coupant ainsi tout ce qui est sur son chemin. Sachez le temps qu'il faut pour que la lame s'arrête après relâchement de l'inte ...

  • Skil 5400 - page 16

    peut remonter ou REBONDIR depuis l'ouvrage lorsque la scie est remise en marche. Supportez les gros panneaux pour minimiser le risque de pincement de lame et de REBOND. Les gros panneaux ont tendance à s'affaisser sous leur propre poids. Des supports doivent être placés sous le panneau des deux côtés, près de la ligne de coupe et pr ...

  • Skil 5400 - page 17

    -17- Symboles IMPORTANT : Certains des symboles suivants peuvent être utilisés sur votre outil. Veuillez les étudier et apprendre leur signification. Une interprétation appropriée de ces symboles vous permettra d'utiliser l'outil de façon plus efficace et plus sûre. Symbole Nom Désignation/Explication V Volts Tension (potentielle) ...

  • Skil 5400 - page 18

    -18- Description fonctionnelle et spécifications Débranchez la fiche de la prise de courant avant d'effectuer quelque assemblage ou réglage que ce soit ou de changer les accessoires. Ces mesures de sécurité préventive réduisent le risque d'une mise en marche accidentelle de l'outil. AVERTISSEMENT ! Capacités maximales Lame 18 ...

  • Skil 5400 - page 19

    MONTAGE DE LA LAME Débranchez la fiche de la prise de courant avant d'effectuer quelque assemblage ou réglage que ce soit ou de changer les accessoires. Ces mesures de sécurité préventive réduisent le risque d'une mise en marche accidentelle de l'outil. 1 . Tournez le GOUJON DE LAME à l'aide de la clé fournie en sens ant ...

  • Skil 5400 - page 20

    -20- Consignes de fonctionnement Débranchez la fiche de la prise de courant. Desserrez le levier de réglage de la profondeur qui se trouve entre le capot et la poignée de la scie. Maintenez la semelle en place d’une main et levez ou baissez la scie par la poignée de l’autre main. Serrez le levier à la profondeur de coupe désirée. Vérifi ...

  • Skil 5400 - page 21

    INTERRUPTEUR À la mise en marche, tenez l’outil à deux mains. Le couple du moteur risque de le renverser. Appuyez sur la gâchette pour mettre l’outil en marche ; relâchez-la pour l’arrêter. La gâchette retourne automatiquement à la position d’arrêt. La scie devrait tourner à plein régime AVANT de commencer à scier et elle ne devr ...

  • Skil 5400 - page 22

    -22- COUPES EN GUICHET Débranchez la fiche de la prise de courant avant de procéder aux réglages. Réglez la lame à la profondeur correspondant à l’épaisseur du matériau à tailler. Inclinez la scie vers l’avant en alignant l’encoche-guide sur la ligne de coupe. Relevez le garde inférieur de la lame, au moyen du levier de levage, et t ...

  • Skil 5400 - page 23

    -23- Accessoires Service L’entretien préventif effectué par des employés non autorisés peut entraîner un positionnement erroné des composants et des fils internes, et ainsi causer des dangers sévères. Nous vous conseillons de faire réparer tous vos outils (y compris le changement de l’ampoule d’éclairage du trait de scie) par un cen ...

  • Skil 5400 - page 24

    -24- Lea y entienda todas las instrucciones. El incumplimiento de todas las instrucciones indicadas a continuación puede dar lugar a sacudidas eléctricas, incendios y/o lesiones personales graves. CONSERVE ESTAS INSTRUCCIONES Area de trabajo Mantenga el área de trabajo limpia y bien iluminada. Las mesas desordenadas y las áreas oscuras invitan ...

  • Skil 5400 - page 25

    -25- La sujeción de la pieza de trabajo con la mano o contra el cuerpo resulta inestable y puede ocasionar pérdida de control. No fuerce la herramienta. Use la herramienta correcta para la aplicación que desea. La herramienta correcta hará el trabajo mejor y con más seguridad a la capacidad nominal para la que está diseñada. No utilice la he ...

  • Skil 5400 - page 26

    -26- inferior usando la palanca de elevación del protector inferior. En cuanto la hoja entre en el material, se debe soltar el protector inferior. Para todas las demás operaciones de aserrado, el protector inferior debe funcionar automáticamente. Asegúrese siempre de que el protector inferior esté cubriendo la hoja antes de dejar la sierra en ...

  • Skil 5400 - page 27

    Al volver a arrancar una sierra en una pieza de trabajo, centre la hoja de sierra en la separación de corte y compruebe que los dientes de la sierra no estén encajados en el material. Si la hoja de sierra se atasca, es posible que se desplace hacia arriba o que se produzca RETROCESO respecto a la pieza de trabajo al volver a arrancar la sierra. S ...

  • Skil 5400 - page 28

    -28- Símbolos IMPORTANTE: Es posible que algunos de los símbolos siguientes se usen en su herramienta. Por favor, estúdielos y aprenda su significado. La interpretación adecuada de estos símbolos le permitirá utilizar la herramienta mejor y con más seguridad. Símbolo Nombre Designación/explicación V Volt Tensión (potencial) A Ampere Corr ...

  • Skil 5400 - page 29

    Desconecte el enchufe de la fuente de energía antes de realizar cualquier ensamblaje o ajuste, o cambiar accesorios. Estas medidas de seguridad preventivas reducen el riesgo de arrancar la herramienta accidentalmente. -29- Descripción funcional y especificaciones ADVERTENCIA ! Capacidades máximas Hoja 184 mm Agujero de eje portaherramienta de la ...

  • Skil 5400 - page 30

    -30- Ensamblaje COLOCACION DE LA HOJA Desconecte el enchufe de la fuente de energía antes de realizar cualquier ensamblaje o ajuste, o cambiar accesorios. Estas medidas de seguridad preventivas reducen el riesgo de arrancar la herramienta accidentalmente. 1. Gire el PERNO DE LA HOJA en sentido contrario al de las agujas del reloj con la llave de t ...

  • Skil 5400 - page 31

    -31- Instrucciones de funcionamiento Desconecte el enchufe de la fuente de energía. Afloje la palanca de ajuste de profundidad situada entre el protector y el mango de la sierra. Sujete la base con una mano y suba o baje la sierra con el mango. Fije la palanca en la posición de ajuste de profundidad deseada. Verifique la profundidad deseada (Fig. ...

  • Skil 5400 - page 32

    -32- GUIA DE LINEA AJUSTABLE (Modelos 5450, 5500, 5600, 5650, y 5700 solamente) Para un corte recto de 90°, puede usar el lado izquierdo o el lado derecho de la muesca de la base. Para cortes inclinados de 45°, use el lado derecho (Fig. 9). La guía se puede ajustar para permitir una variación de grosores de hoja para el lado de la hoja que el u ...

  • Skil 5400 - page 33

    -33- CORTES DE BOLSILLOS Desconecte el enchufe de la fuente de energía antes de realizar ajustes. Coloque el ajuste de profundidad de acuerdo con el material que va a cortar. Incline la sierra hacia adelante con la muesca de la guía de corte alineada con la línea que usted ha trazado. Levante el protector inferior utilizando la palanca de elevac ...

  • Skil 5400 - page 34

    -34- Servicio El mantenimiento preventivo realizado por personal no autorizado pude dar lugar a la colocación incorrecta de cables y componentes internos que podría constituir un peligro serio. Recomendamos que todo el servicio de las herramientas, incluyendo el reemplazo de la bombilla del indicador de la línea de corte, sea realizado por un Ce ...

  • Skil 5400 - page 35

    -35- Notes: Remarques : Notas: SM 2610925541 10-04 11/1/04 12:23 PM Page 35 ...

  • Skil 5400 - page 36

    2610925541 10/04 Printed in Mexico LIMITED WARRANTY OF SKIL CONSUMER PORTABLE POWER TOOLS FOR HOME USE Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all SKIL consumer portable power tools will be free from defects in material or workmanship for a period of two years from date of purchase. SELLER’S SOLE ...

Manufacturer Skil Category Saw

Documents that we receive from a manufacturer of a Skil 5400 can be divided into several groups. They are, among others:
- Skil technical drawings
- 5400 manuals
- Skil product data sheets
- information booklets
- or energy labels Skil 5400
All of them are important, but the most important information from the point of view of use of the device are in the user manual Skil 5400.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Skil 5400, service manual, brief instructions and user manuals Skil 5400. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Skil 5400.

Similar manuals

A complete manual for the device Skil 5400, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Skil 5400 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Skil 5400.

A complete Skil manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Skil 5400 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Skil 5400, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Skil 5400, that we can find in the current document
3. Tips how to use the basic functions of the device Skil 5400 - which should help us in our first steps of using Skil 5400
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Skil 5400
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Skil 5400 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Skil 5400?

Use the form below

If you did not solve your problem by using a manual Skil 5400, ask a question using the form below. If a user had a similar problem with Skil 5400 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)