Manual Canon DR DR-X10C

157 pages Not applicable
Download

Go to site of 157

Summary
  • Canon DR DR-X10C - page 1

    Please read this man ual before using the scanner. After you finish reading this ma nual, keep it in a safe place for future reference. User Manual ...

  • Canon DR DR-X10C - page 2

    i FCC REGULATIONS (F or 120 V model) Document Scanner, Model M11063 This device complies with Part 15 of the FCC Rules. Operation is subject to the fo llowing two conditions: (1) This device may not cause harmful inte rference, and (2 ) this device must accept any interference re ceived , including interference that may cause undesired operation. N ...

  • Canon DR DR-X10C - page 3

    ii European Union (and EEA) only. This symbol indicates tha t this product is not to be disposed of with your ho usehold waste, according to the WEEE Directive (2002/96/EC) and your national law. This produc t should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an ...

  • Canon DR DR-X10C - page 4

    iii Introduction Thank you for purchasing the Canon imageFORMULA DR-X10C Document Scanner. Please read this and the following manuals thoroughly before using the scan ner to become acquainted with its capabil ities and make the most of its many functions. After reading the manual s, store them in a safe place fo r future reference. Manuals for the ...

  • Canon DR DR-X10C - page 5

    iv • Electroni c versions of all manuals ar e available for viewing from the Setu p CD. Symbols Used in This Manual The following symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions that should be observed for safety. WARNING Indicates a warning concerning operations that may lead to death o ...

  • Canon DR DR-X10C - page 6

    v How This Manual is Organized This manual consists of the f ollowing chapters. ■ Hardware Chapter 1 Befo re You Start Using the Scan ner Provides an overview of the DR-X10C Chapter 2 Setu p Describes the DR-X10C op er ating environment and how to connect to a PC Chapter 3 Basic Operation Describes the basic uses of the DR-X10C Chapter 4 Ot her F ...

  • Canon DR DR-X10C - page 7

    User Manual Hardware Please read this man ual before using the scanner. After you finish reading this ma nual, keep it in a safe place for future reference. ...

  • Canon DR DR-X10C - page 8

    ii Hardware Table of Contents Introduction......................... .............. .............. .........iii Manuals fo r the Scanner ..................... ............. ....... iii Symbols Used in This Manual ............. ............. ....... iv How This Manua l is Organized ............ ............. ........ v Chapter 1 Before You Start Usin ...

  • Canon DR DR-X10C - page 9

    iii Hardware 3. Imprinter Ink Cartridge Replacement and Cleaning ................. .............. ...................... .... 5-14 About the Imprinter ............ ............. ............. ....... 5-14 Replacing I nk Cartridges ........................ ............ 5-15 Cleaning t he Print H eads... ............. .......... .......... 5-19 Impri ...

  • Canon DR DR-X10C - page 10

    Chapter 1 Before You Start Using the Scanner 1. Important Safety Instruct ions ................... ........ 1-2 Installat ion Locat ion ..................... ............. ............ 1-2 Power ............ ............. .......... ............. ............. ....... 1 -2 Moving the Scanner ........................ .......... ............ 1-3 Hand ...

  • Canon DR DR-X10C - page 11

    1-2 Chapter 1 Before You Start Using the Scanner 1. Important Safety Instructions To ensure the safe operation of this sc anner, be sure to read the safety wa rnings and precautio ns described below. Installation Location The performance of this sc anner is affected by the environment in which it is installed. Make sure that the location where the ...

  • Canon DR DR-X10C - page 12

    1-3 Chapter 1 Before You Start Using the Scanner ● Do not pull directly on the power cord. W hen disconnectin g the power cord, gra sp the plug and remove it from the outlet. ● Keep the area around the powe r plug clear of objects so that the power cord can be disconnected easily in an emergency. ● If you have any questions regarding th e pow ...

  • Canon DR DR-X10C - page 13

    1-4 Chapter 1 Before You Start Using the Scanner ■ Some parts can only be cleaned when the power is turned ON. In these ca ses, be careful to avoid electric shoc k. ■ Clean the scanner usin g a slightly dampened cloth which has been well wrung out. Neve r use alcohol, benzene, paint thinner, or any other flamma ble substances. ■ If the scanne ...

  • Canon DR DR-X10C - page 14

    1-5 Chapter 1 Before You Start Using the Scanner ■ Do not wear loose clothing or jewelry th at may get caught in the scanner whil e you are usi ng it. This may result in personal injury. Be extra careful of neckties and long h air. If anything becomes caught in the scanner, immediat ely disconn ect the power cord to stop the scanner. ■ Be caref ...

  • Canon DR DR-X10C - page 15

    1-6 Chapter 1 Before You Start Using the Scanner 2. Features The main features of the DR-X10C are described below. Scanner Feature s ● Fast Document Feeding The scanner can scan up to 100 document sheets per minute of LTR/A4-size pape r in black and white, grayscale, a nd co lor scanning modes. * Scanning co nditions: LTR/A4 portrait , duplex, 20 ...

  • Canon DR DR-X10C - page 16

    1-7 Chapter 1 Before You Start Using the Scanner Detection Func tions ● Auto Image Type Detection The scanner auto matically detects whether documents are in black and white or color. ● Auto Paper Si ze Detection The document page size is detected before scanning. ● Skew Detecti on Functi on The scanner stops feeding when a skewed document is ...

  • Canon DR DR-X10C - page 17

    1-8 Chapter 1 Before You Start Using the Scanner ● Dropout and Color Enhancement Functions The scanner is equippe d with drop-out and enhancement functions that enable you to specify one color (red, blue, or green) to be omitted (dropped out) or enhanced when scanning, respectively. ● Remove Binder Hol es Erases the shadows that appe ar on scan ...

  • Canon DR DR-X10C - page 18

    1-9 Chapter 1 Before You Start Using the Scanner Other Functions ● Rapid Recovery System When this function is activ at ed and a sensor detects a misfeed due to a paper jam or double feed, which causes feeding to stop, scanning pa uses to allow you to correct the cause of the misfeed, af ter which scanning continues from the document page on wh i ...

  • Canon DR DR-X10C - page 19

    1-10 Chapter 1 Before You Start Using the Scanner 3. Names and Functions of Parts The names and functions of the DR-X10C parts are shown below. Front View, Feeder Inlet, and Eject Outle t a Document Ejec t Tray Scanned documents are output here. (See p. 3-11.) b Document Feed Tray Load documents to be scanned. (See p. 3-7.) c Power Switch Turns the ...

  • Canon DR DR-X10C - page 20

    1-11 Chapter 1 Before You Start Using the Scanner Rear View a USB Connector (Type B) Connect the supplied USB cable here. (See p. 2-6.) b SCSI Connector (50-pin half-pitch D-sub receptacle) Connect the SCSI cable here. (See p. 2-7.) c DIP Switch (SCSI ID) Selects the sc anner’s SCSI ID. (See p. 2-8.) d Power Connector Connect the supplied power c ...

  • Canon DR DR-X10C - page 21

    Chapter 2 Setup 1. Setup Procedures . ............ .............. .............. ... 2-2 2. Installation Requirement s ............ .............. ...... 2-3 3. Software Installation ... ......... .............. ........... ... 2-4 About the S etup Me nu ...................... ........... ......... 2-4 4. Connecting the Scanner to the Computer .... ...

  • Canon DR DR-X10C - page 22

    2-2 Chapter 2 Setup 1. Setup Procedures Perform the following setup procedures to prepare the scanner for use. Step 1: Confirm the in stallation requirements. (See p. 2-3) Step 2: I nstall the Software. (See p. 2-4) Step 3: Connect the scanner to the computer. (See p. 2-6) Step 4: Turn the power ON (Scanner recognition ). (See p. 2-9) IMPORTANT • ...

  • Canon DR DR-X10C - page 23

    2-3 Chapter 2 Setup 2. Installation Requirements To use the DR-X10C, your computer must satisfy the following system requirements. ■ Operating System: • Microsoft Windows 2000 Professional SP4 or later • Micros oft Wind ows XP Pr ofessional SP2 or later • Microsoft Windows XP Home Edition SP2 or later • Microsoft Windows XP Professional x ...

  • Canon DR DR-X10C - page 24

    2-4 Chapter 2 Setup 3. Software Installation This section describes how to install the software. About the Setup Menu When you insert the inclu ded Setup disc into the computer’ s CD drive, the menu shown below sh ould appear. If the menu does not appear, use Explorer to access the CD drive and execute the file “S ETUP.EXE”. IMPORTANT • As ...

  • Canon DR DR-X10C - page 25

    2-5 Chapter 2 Setup ■ The Custom Installation Screen This screen appears when you click “Custom Installation” on the Menu screen. Select the check boxes next to the software that you want to install. Click [Install] to install the selected software. ■ The Read Manual Screen From this screen you can select one of the supplied electronic manu ...

  • Canon DR DR-X10C - page 26

    2-6 Chapter 2 Setup 4. Connecting the Scanner to the Computer There are two methods for conn ecting the DR-X10C scanner to a co mputer: a USB connection to a st andard USB port built in to the computer, or SCSI co nnection to a SCSI card installed in an expansion slot of the computer. Se lect the method that is best suited to your computer environm ...

  • Canon DR DR-X10C - page 27

    2-7 Chapter 2 Setup 3. Use the supplied USB cable to connect the scanner to the computer. Connect the square plug (Type B) of the USB cable to the scanner. ■ Using a SCSI Connection IMPORTANT Make sure that the computer i s turned OFF be fore connect ing the SCSI cabl e. If the ca ble is conne cted while the computer is on, the sc anner may n ot ...

  • Canon DR DR-X10C - page 28

    2-8 Chapter 2 Setup IMPORTANT Observe the fo llowing when connecting t he scanner wit h other devices in a “d aisy chain” . • The SCSI ID of the scanner is set to “S CSI ID = 2” by de fault. When using a dais y-chain confi guration with other SCSI devices, set the DIP switche s so that SCSI ID numb ers are not duplicated in the syst em. ? ...

  • Canon DR DR-X10C - page 29

    2-9 Chapter 2 Setup 5. Turning the Power ON (Scanner Recognition) When you turn ON the computer and the scanner, the Windows Pl ug and Play function recognizes the scanner and automatically installs the required device driver. About the Power Switch When the power switch (located at the low er left side of the front of the scanner) is turned ON, th ...

  • Canon DR DR-X10C - page 30

    2-10 Chapter 2 Setup Hint • With Window s Vista, insta llation proce eds automat ically regardles s of the disp layed “Check here for stat us” balloon help. You can click “Che ck here f or statu s” to di splay the installat ion progress. • With Windows XP and Vista, a message appe ars when installation is finish ed. •W i n d o w s X P ...

  • Canon DR DR-X10C - page 31

    Chapter 3 Basic Operation 1. Turning the Power ON and OFF ........... ........... 3-2 About the P ower Switch ..... ............. ............. ......... 3-2 2. Documents................ .............. ........... .............. 3-4 Acceptable Docum ents ...... ............. ............. ......... 3-4 3. Document Feed and Ejec t Trays . ......... ...

  • Canon DR DR-X10C - page 32

    3-2 Chapter 3 Basic Operation 1. Turning the Power ON and OFF Use the power switch to turn the DR-X10C scanner ON and OFF, or if you are using a USB connect ion, you can set the USB-linked power switch. CAUTION • After turn ing the sca nner OFF, wait a t least ten se conds before turning it ba ck ON. • If the s canner is connected v ia SCSI cab ...

  • Canon DR DR-X10C - page 33

    3-3 Chapter 3 Basic Operation 4. Press [Enter]. The current setting is indicated by blinking square brackets [ ]. 5. Press the [ ] or [ ] key to select [ON] or [OFF], and press [Enter] to accept the selection. 6. Press the Stop key to exit the User Mode. Enter Key ...

  • Canon DR DR-X10C - page 34

    3-4 Chapter 3 Basic Operation 2. Documents The DR-X10C scanner can scan documents ranging in size from busin ess cards and checks to 11" × 17"/A3 size. The size and type of paper that can be fed de pends on the feeding method. Acceptable Documents The scanner can feed the following document sizes. Size Width: 2" to 12.01" (50.8 ...

  • Canon DR DR-X10C - page 35

    3-5 Chapter 3 Basic Operation • To scan bound multi-pag e documents such as invo ice booklets, place the boun d edge agains t the feeder inlet and scan by ma nual feedi ng. • To use the Long Document Mode, f eed document pa ges manually, one afte r another. ■ Long Document Mode Setting Using the Long Document mode, pages up to 118.1" (3 ...

  • Canon DR DR-X10C - page 36

    3-6 Chapter 3 Basic Operation • Some scanning mode and resolu tion setting s may produce incomplet e page images . In this case , try decreas ing the resolution or, if scannin g in color mod e, switch to b lack and white. • If a sheet is loaded at a skew ed angle when scanning lon g documents, i t may be damage d by contac ting both s ides of t ...

  • Canon DR DR-X10C - page 37

    3-7 Chapter 3 Basic Operation 3. Document Feed and Eject Trays Before scanning, prepare the Docum ent Feed and Ej ect Trays for th e desired paper size. Preparing the Document Feed Tray ■ Opening the Document Feed Tray When the scanner is turned ON, the Docume nt Feed Tray opens automatically and move s to the spe cified home position height. Hin ...

  • Canon DR DR-X10C - page 38

    3-8 Chapter 3 Basic Operation The current setting is indicated by blinking square brackets [ ]. 5. Press the [ ] or [ ] key to select [1], [2 ] or [3]. The Document Feed Tray moves to the sel ected heig ht. 6. Press [Enter] to accept the selection. 7. Press the Stop key to exit the User Mode. ■ Closing the Document Feed Tray To close the Docume n ...

  • Canon DR DR-X10C - page 39

    3-9 Chapter 3 Basic Operation ■ Document Feed Tray Extension Pull out the tray extension as needed for the length of your document. Adjusting the Document Guides The document guides normally ex tend at equal distances from the left and right of the center of feeding so that your documents are centered in the fe ed inlet. However, each document gu ...

  • Canon DR DR-X10C - page 40

    3-10 Chapter 3 Basic Operation 4. Lock the right document guide ( a ), and unlock the left document guide ( b ). 5. Slide the left document guide to the left edge of your documen ts. ■ Resetting the Document Guides To reset the guides so that they are equidistant from the center, perform the following procedure to spread the guides to the left an ...

  • Canon DR DR-X10C - page 41

    3-11 Chapter 3 Basic Operation Preparing the Document Eject Tray The Eject Tray in cludes two Document Eject Gu ides, the Eject Tray Extension and Eject Paper Stopper, to be adjusted to match the length of your documents. ■ Document Guides Slide the docu ment eject guides to mat ch the width of your documents. Hint • The positi on of the do cum ...

  • Canon DR DR-X10C - page 42

    3-12 Chapter 3 Basic Operation 4. Document Feeding Methods Two document feeding methods are available: Continuous Feeding, which feeds document s automatically from the document tray by the pickup roller; and Manual Feeding, wh ich requires one document at a time to be positioned manually for transport by the feed roller, while the pi ckup roller i ...

  • Canon DR DR-X10C - page 43

    3-13 Chapter 3 Basic Operation Continuous Manual Feeding Mode Enable the Continuous Manu al Feeding Mode from the User Mode when document pag es do not separate well using Continuous Feeding. IMPORTANT When the Contin uous Manual Feed ing Mode is set t o ON from the User Mode, ma ke sure to disa ble it (set to OFF ) when finished sc anning. Othe rw ...

  • Canon DR DR-X10C - page 44

    3-14 Chapter 3 Basic Operation 5. Scanning Scanning operations can be controlled by a scanning application program such as the CapturePerfect 3.0 software included with t he scanner, or directly from the control pa nel of the DR-X10C, using the Job Function. This section describes the Job Function and provides an overview of CapturePerfect 3.0. Abo ...

  • Canon DR DR-X10C - page 45

    3-15 Chapter 3 Basic Operation CapturePerfect 3.0 CapturePerfect 3.0 is an ISIS-compatibl e applic ation developed for Canon do cument scanners. CapturePerfect 3.0 includes the following modes. Select the desired scan mode from the Sc an menu to perform scanning. For more information on Captur ePerfect 3.0, refer to the CapturePerfect 3. 0 Operatio ...

  • Canon DR DR-X10C - page 46

    3-16 Chapter 3 Basic Operation Scan To Presentation This mode is convenient when a compact scanner is used in an environment such as a conference hall, where it is connected to a large displa y or projector. By setting CapturePerfect for full-scree n display before scanning, scanned images are displa yed at full size on the screen. Hint This is not ...

  • Canon DR DR-X10C - page 47

    3-17 Chapter 3 Basic Operation 4. Set the [Default Page Size]. IMPORTANT If you select [Default] in the ISIS driver pro perties dia log box, that sett ing is a pplied here. 5. Click [OK] to finish scanner selection. 6. From the [Scan] menu, select [Scanner Setting]. The Properties dialog box for the ISIS driver opens. 7. Set the scan settings. Hint ...

  • Canon DR DR-X10C - page 48

    3-18 Chapter 3 Basic Operation 10. Place your document and click [Save] to start scanning. IMPORTANT You must load your do cuments as descri bed below, depe nding on the specif ied Feed Optio n setting. • If the [Standard Feeding ] Feed Option is enabled, load your documents be fore scann ing. When all of the documents have been scanned , the Con ...

  • Canon DR DR-X10C - page 49

    3-19 Chapter 3 Basic Operation 6. Using Patchcode Sheets (Option) When the optional patchcode dec oder is installed, the DR-X10C supports Automati c File Separation by dete cting patchcode sheets inserted within a document, and performs batch separation. About Patchcode Sheets Patchcode patterns are printed on the patchcode sheets used to automatic ...

  • Canon DR DR-X10C - page 50

    3-20 Chapter 3 Basic Operation How to Use Patchcode Sheets This section describes how to use patchcode sheets with CapturePerfect 3.0. 1. Print the patchcode sheets on a printer. IMPORTANT • Print (at original size) PATCH T (A4) and PATCH II (A 4) sheets on A4 paper, or PATCH T (LTR) a nd PATCH I I (LTR) on LTR pa per. • The scanne r may not re ...

  • Canon DR DR-X10C - page 51

    3-21 Chapter 3 Basic Operation 7. Clearing a Paper Jam or Double Feed Error If a paper jam or double feed occurs during scanning, a paper jam message appears on th e PC and on the scan ner’s display panel. Use the following procedure to clear the paper jam. CAUTION • When removi ng jammed paper, take care not to cut your hands on the edges of t ...

  • Canon DR DR-X10C - page 52

    3-22 Chapter 3 Basic Operation IMPORTANT The Rapid Recov ery System setting in the ISIS/TWAIN dr iver causes the fo llowing pr ocess to occur after a pap er jam. (See “[Rapid Recov ery System] Check Box” on p. 8-17.) • When the Rapid Recover y System is disabl ed, images scanned bef ore the pape r jam occurs are saved as file s, scanning fi n ...

  • Canon DR DR-X10C - page 53

    3-23 Chapter 3 Basic Operation • When the Rapid Recover y System is enable d, scannin g pauses when a double feed is det ected, and t he followi ng error messa ge is displaye d. ■ When the Rapid Recovery System is Disabled Return the document pages ejec ted as a result of double- feed detection to the top of the document stack yet to be scanned ...

  • Canon DR DR-X10C - page 54

    Chapter 4 Other Functions 1. Other Functions and Settings .......................... 4-2 2. Function Description ................. ............... ........ 4- 4 3. User Mode ............. .............. .............. .............. 4-9 User Mode Operating Procedure ..........................4-9 4. User Mode Functions................... ........... ...

  • Canon DR DR-X10C - page 55

    4-2 Chapter 4 Other Functions 1. Other Functions and Settings The following DR-X10C functions are grouped together as Ot her Functions. For details, re fer to the indicated pages. Operati on/Setting Me thod Applicab le P age P anel Operat ion User Mode ISIS/TW AIN SCSI Speed – ✔ – p. 4-12 USB Short Pack et – ✔ – p. 4-12 Auto USB Power S ...

  • Canon DR DR-X10C - page 56

    4-3 Chapter 4 Other Functions Hint • The Operation/Setting Method s are as fo llows: Panel Operat ion: The operat ion or setting is performed u sing the cont rol panel keys. User Mode: The s canner funct ion setting is made as a User Mode se lection. ISIS/TWAIN: The function is an ISIS/TWAIN driver scanning set ting. CapturePer fect: The fun ctio ...

  • Canon DR DR-X10C - page 57

    4-4 Chapter 4 Other Functions 2. Function Description The Other Functions ar e described below. See “User Mode” on p. 4-9 , for descriptio ns of the func tions set from the User Mode. ■ Count-Only Mode Counts the number of loaded document sheets by simply feeding them through the scanner. Hint The Count-Onl y mode is ex ecuted by t he Count O ...

  • Canon DR DR-X10C - page 58

    4-5 Chapter 4 Other Functions 3. Press the Start Key to start scanning. “Verifying…” is displayed. Hint If the speci fied count is ex ceeded while sc anning, o r if the scanned count does not reach the specified c ount when scanning is f inished, an error is disp layed. The specified cou nt is exceeded whi le scanning Scanning finishes withou ...

  • Canon DR DR-X10C - page 59

    4-6 Chapter 4 Other Functions IMPORTANT • Ultrasonic double-fee d detection works only whe n the document pa ges overlap by at least two inches (50 mm). • If documents stick toge ther due to s tatic electric ity, Ultrasonic Double-F eed Detectio n may not functio n correctly . • If the pres ence of adhesi ve notes or lab els on pages is detec ...

  • Canon DR DR-X10C - page 60

    4-7 Chapter 4 Other Functions ■ Selectable Background You can specify whether the background behind th e scanned image is black or white. The background is changed by rotating the platen rollers to expose either the black or wh ite part of the rollers, according to t he selection specified in t he ISIS/TWAIN driver. IMPORTANT Image proce ssing pe ...

  • Canon DR DR-X10C - page 61

    4-8 Chapter 4 Other Functions ■ Locking the Keys (Invalidate Key Function) Press and hold the [Enter] key for approximately 5 seconds to display the Invalidate Key setting. Press the [ ] key to select [OK], and press [Enter] to disable the keys. IMPORTANT • To unlock the keys, pres s and hold th e [Enter] key again for approximat ely 5 seconds, ...

  • Canon DR DR-X10C - page 62

    4-9 Chapter 4 Other Functions 3. User Mode The User Mode provides the user with the ca pability to change cert ain scanner functions. User Mode Operating Procedure User Mode operations are controlled by the following procedure. Hint Operating pr ocedures dif fer according to User Mode fu nction. For details, r efer to th e indicated p ages. 1. Pres ...

  • Canon DR DR-X10C - page 63

    4-10 Chapter 4 Other Functions 3. Press [Enter]. The current setting is indicated by blinking square brackets [ ]. 4. Press the [ ] or [ ] key to select [ON] or [OFF], and press [Enter] to accept the selection. Enter Key ...

  • Canon DR DR-X10C - page 64

    4-11 Chapter 4 Other Functions 4. User Mode Functions The following functions are available in the User Mode. ■ Buzzer (Beeper) Control Setting The beeper (“buzzer”) sounds when you press the control panel keys and when a scanning erro r occurs. ON2: The beeper sounds when a scanner error occurs. ON1: The beeper sounds when a scanner error oc ...

  • Canon DR DR-X10C - page 65

    4-12 Chapter 4 Other Functions Hint Feeding a d ocument lo nger the ma ximum detectab le page si ze for Auto De tection ca uses a pa per jam ind ication, and transport stops. ■ Continuous Manual Feeding Mode Setting This mode disables automatic feeding by the pick up roller, so that the loa ded document st ack must be fed by hand one sheet at a t ...

  • Canon DR DR-X10C - page 66

    4-13 Chapter 4 Other Functions ■ Fram e Detection Err or Mode Setting If set to ON, an error message is displayed when the correct paper size of the image cannot be detected. If detection fails, the se nsor may have failed. IMPORTANT • When the error message is dis played, clea n both the sens or glass and the re ading glas s. (See “Cleaning ...

  • Canon DR DR-X10C - page 67

    4-14 Chapter 4 Other Functions ■ Imprinter Test When the optional imprinter is installed, t his function executes a test print i ng of the imprinter. (See “Performing an Imprinter Test” on p. 5-20.) ■ Cleaning Mode This function executes rolle r cleaning using a cleaning sheet. (See “Cleaning Roll ers w ith a Cleaning Sheet” on p. 5-4.) ...

  • Canon DR DR-X10C - page 68

    Chapter 5 Maintenance 1. Regular Maintenance................... .............. ...... 5- 2 Cleaning the Scanner..... ............. ........... ............ ... 5-2 Cleaning the Glass and Ro llers................... ..........5-3 Opening and Closing the Upper Unit .. ............. ..... 5-3 Cleaning Rollers with a Clean ing Sheet .............. .. 5 ...

  • Canon DR DR-X10C - page 69

    5-2 Chapter 5 Maintenance 1. Regular Maintenance To maintain scanning quality, routinely clean the scanner as described below. CAUTION • Do not use spra y cleaners to clean the sc anner. Preci sion mechanisms ma y get wet and mal function. • Never use pa int thinne r, alcohol, or other orga nic solven ts to clean th e scanner. Such solvents may ...

  • Canon DR DR-X10C - page 70

    5-3 Chapter 5 Maintenance Cleaning the Glass and Rollers If scanned images contain spot s or documents become dirty after scanning, the scanning gla ss or transport rollers inside the scanner may be dirty. The locations of the main gla s s and rollers are as follows. For instructions on cleaning the gl ass and rollers, refer to the following pages. ...

  • Canon DR DR-X10C - page 71

    5-4 Chapter 5 Maintenance Hint An error messa ge appears on the display panel if the up per unit is open (r aised). Cleaning Rollers with a Cleaning Sheet Rollers in the tran sport path are cleaned using the Cleaning Mode of the User Mode , using a cleaning sheet. Hint • Each clean ing shee t is used several ti mes to cl ean one si de of the roll ...

  • Canon DR DR-X10C - page 72

    5-5 Chapter 5 Maintenance 6. Insert the cleaning sheet adhesive-side up into the feed inlet. The cleaning sheet feeds through the scanner, and the Cleaning Mode exits. 7. Inspect the cleaning sheet for dust. 8. Repeat steps 3 to 6 several times using the same cleaning sheet to clean the same side of the rollers. 9. Prepare a new cl eaning shee t, a ...

  • Canon DR DR-X10C - page 73

    5-6 Chapter 5 Maintenance 3. Wipe any dust off the scanning glass with a clean, dry cloth. 4. Press the Stop key to turn off the lamp. 5. Carefully lower the upper unit ( a ). Press down on both sides of the upper unit to ensure that it is securely closed. ( b ) Cleaning the Platen Rollers The platen rollers are located near the upper and lower sid ...

  • Canon DR DR-X10C - page 74

    5-7 Chapter 5 Maintenance 3. Clean the black and white surfa ces of the rollers by wiping horizontally wi th a moistened, wrung-out cloth. IMPORTANT When cleaning , be careful not to bend th e sheet over t he roller. The locatio n of the sheet fo r the lower plat en roller is in fro nt of the roller. 4. Use a soft object such as a cotton swab to re ...

  • Canon DR DR-X10C - page 75

    5-8 Chapter 5 Maintenance 3. Lift the pickup roller mounting lever, and remove the roller. 4. Pull the feed roller lock lever down ( a ) and move it to the right ( b ) to unlock the feed roller. 5. Remove the feed roller. 6. Use a moistened, well wrung-o ut cloth to wipe off any dust from the rollers. ■ Reinstalling Pickup and Feed Rollers 1. Set ...

  • Canon DR DR-X10C - page 76

    5-9 Chapter 5 Maintenance 3. Push the feed roller lock lever up ( a ) and move i t to the left ( b ) to lock the feed roller in place. 4. Push the roller cover up un til it clicks into place. IMPORTANT When opening an d closing t he roller cov er, be carefu l not to touch the gl ass (stapl e detectio n window). If t he glass get s dirty, staple det ...

  • Canon DR DR-X10C - page 77

    5-10 Chapter 5 Maintenance 3. Push the roller lock lever up ( a ) and move it to the left ( b ) to unlock the roller. 4. Remove the retard roller. 5. Use a moistened, well wrung-o ut cloth to wipe off any dirt from the roller. ■ Reinstalling the Retard Roller 1. Set the retard roller in to place in the scanner. 2. Align the notches in the roller ...

  • Canon DR DR-X10C - page 78

    5-11 Chapter 5 Maintenance 4. Replace the roller cover. 5. Push the front of th e roller cover in until it clicks into place. 6. Carefully lower the upper unit ( a ). Press down on both sides of the upper unit to ensure that it is securely closed.( b ) ...

  • Canon DR DR-X10C - page 79

    5-12 Chapter 5 Maintenance 2. Replacing the Transport Rollers As the rollers st art to wear out, f eeding quality declines, and document feed errors, such as paper jams, becom e more likely. If document feed errors continue to occur after c leaning the rollers, pu rchase the Roller R eplacement Kit and repl ace the trans port rollers (pickup, feed, ...

  • Canon DR DR-X10C - page 80

    5-13 Chapter 5 Maintenance Checking and Resetting the Page Count er The roller usage counter can be checked and reset using the Roller Counter User Mode setting. IMPORTANT • This counte r shows the nu mber of pages tr ansporte d by the currentl y installed feed roller s. Make sure to rese t the counter when you replac e the rollers. • The Total ...

  • Canon DR DR-X10C - page 81

    5-14 Chapter 5 Maintenance 3. Imprinter Ink Cartridge Replacement and Cleaning When the optio nal imprinter is used, pri nting will beco me faint or nonexistent when the ink is de pleted. It is recommended to k ee p a spare ink cartridge on hand. About the Imprinter There are two typ es of imprinter : the Pre-imprinter, which prints on documents be ...

  • Canon DR DR-X10C - page 82

    5-15 Chapter 5 Maintenance Replacing Ink Cartridges Replace the ink cartridge us ing the following procedure. IMPORTANT After repl acing an in k cartridge, run a test p rint to conf irm proper printing. ( See “Imprint er Testing ” on p. 5-20 .) ■ Replacing the Ink Cartridge (Pre-Imprinter) IMPORTANT When the upper un it is raise d, the pre-im ...

  • Canon DR DR-X10C - page 83

    5-16 Chapter 5 Maintenance CAUTION Peel off the s eal covering the nozzle s of a cartridge only if you are going to us e it immediately. Also, avoid t ouching the meta l contacts or nozzl es of the ink cart ridge. 5. Open the carriage and insert a new in k cartridge. 6. Turn the lock lever upwa rds to secure the ink cartridge. IMPORTANT • If the ...

  • Canon DR DR-X10C - page 84

    5-17 Chapter 5 Maintenance ■ Replacing the Ink Cartridge (Post-Imprinter) Replace the Post-imprinter ink cartridge using the following procedure. 1. Adjust the document feed guide s outward to allow access to the im printer cover. 2. Press the imprinter cover tab (indi cated by the arrow in the illustration) to unlock it. 3. Open the imprinter co ...

  • Canon DR DR-X10C - page 85

    5-18 Chapter 5 Maintenance CAUTION Peel off the s eal covering the nozzle s of a cartridge only if you are going to us e it immediately. Also, avoid t ouching the meta l contacts or nozzl es of the ink cart ridge. 7. Install the new cartridge with the nozzles facing to the right. 8. Push the ink cartrid ge as indica ted by the arrow un til it click ...

  • Canon DR DR-X10C - page 86

    5-19 Chapter 5 Maintenance Cleaning the Print Heads If the imprinter print head nozzles are dirty, printing may become streaked or spotty. To prevent this, periodically remove the ink cartri dge and clean the print head with a soft, dry cloth or cotton swab. CAUTION Do not touch th e metal contac ts on the ink cart ridge. Doing so may cause poor co ...

  • Canon DR DR-X10C - page 87

    5-20 Chapter 5 Maintenance Imprinter Testing After repl acing an ink cartridge or cleani ng the print head, perfo rm a test print to co nfirm proper pri nting. Test prin ting is perfor med by the “Imprin ter Test” User M ode selection. IMPORTANT Before perfo rming an Imprin ter Test, loa d a sheet of paper into the Document Fe ed Tray. ■ Perf ...

  • Canon DR DR-X10C - page 88

    Chapter 6 Practical Examples 1. Messages ........... ............................ ........... ...... 6 -2 Status Display .................... ............. ............. ......... 6-2 Error Messages ............ ........... ............. ............. .... 6-3 2. Troubleshooting ................... .............. .............. 6-5 Trouble Categori ...

  • Canon DR DR-X10C - page 89

    6-2 Chapter 6 Practical Examples 1. Messages There are two types of display panel messag e s: “status indicator mess ages” and “error messages” that appear when the scanner encounters a problem . Status Display The following messages appe ar on the display panel to indicate the scanne r’s operating state: ■ Coun ting... Status: Operatin ...

  • Canon DR DR-X10C - page 90

    6-3 Chapter 6 Practical Examples Error Messages When one of the foll owing messages appe ars o n the display panel, an error has occurred in the scanner. Foll ow the indicated procedure to resolve the error. ■ Check Imprinter Error Code: H001 Problem: No ink cartridge is instal led in th e post- imprinter. Solution: Install an ink cartridge. Erro ...

  • Canon DR DR-X10C - page 91

    6-4 Chapter 6 Practical Examples ■ Skew Detected Error Code: J018 Problem: A skewed document page contacted the wall of the transport path. Solution: Remove and repositi on the d ocument page. ■ Double Feed Error Code: D002 Problem: A double feed was detected by the document length. Solution: Remove the double fed document page(s) from the ejec ...

  • Canon DR DR-X10C - page 92

    6-5 Chapter 6 Practical Examples 2. Troubleshooting This section describes the problems that may occur during use of th e scanner and how to solve them. Trouble Categories The following trouble categories are addressed: • The Scanner Does Not Turn ON (See p. 6-5) • The Scanner Is Not Recognized (Connecting via USB) (See p. 6-5) • The Scanner ...

  • Canon DR DR-X10C - page 93

    6-6 Chapter 6 Practical Examples ■ The Scanner Is Not Recognized (Connecting via SCSI) If the scanner’s SCSI connecti on is not recognized, first confirm the following: ✔ Are the scanner and PC connected correctly using the proper cable? ✔ Is the scanner’s power switch turned ON? ✔ Is the SCSI card in the PC opera ting properly? ✔ Was ...

  • Canon DR DR-X10C - page 94

    6-7 Chapter 6 Practical Examples If this does not solve the pr obl em, consider the followi ng possible causes: Cause Other applications are running in the background on your PC. Solution Quit all other appl ications that are running. Cause Resident applicati ons, such as anti -virus software, are draining memory resources. Solution Quit all resi d ...

  • Canon DR DR-X10C - page 95

    6-8 Chapter 6 Practical Examples Problem The scanned imag e is too dark (or faint). Cause The [Brightness] setting is not set to an appropriate value. Solution If the image is too dark, set a higher brightn ess setting, or if the image is too faint, set a lower brightness setting. Problem Text or images from the back side of you r document appear i ...

  • Canon DR DR-X10C - page 96

    6-9 Chapter 6 Practical Examples 3. Uninstalling the Software Some scanner malfunctions can be resolved by reinstalling the software. Before reinstalling the software, make su re to co mplete ly uninstall any previous installation first. Uninstalling the ISIS/TWAIN Driver The following procedure uses the ISIS/TWAIN driver as an example. Follow the ...

  • Canon DR DR-X10C - page 97

    6-10 Chapter 6 Practical Examples 4. Click [Yes] to p roceed with uninstal lation. 5. When uninstallation is finished, click [Fini sh]. ...

  • Canon DR DR-X10C - page 98

    Chapter 7 Appendix 1. Specifications.............. .............. ............... ........ 7-2 Unit Specific ations ........... ............. ........... ............. . 7-2 Options ............ ............. ............. ........... ............. .... 7-4 Consummabl es .... .............. ............. ............. ......... 7-4 External Dimen s ...

  • Canon DR DR-X10C - page 99

    7-2 Chapter 7 Appendix 1. Specifications Unit Specifications Type Desktop sheet-fed scanner Scannable Document Requi rements Width: 2" to 12.01" (50.8 mm to 305 mm) Length: 2.76" to 17.01" (70 to mm 432 mm) Weight: Page Separation Feeding: 14 lb to 32 lb bond (52 g/m 2 to 128 g/m 2 ) (0.06 mm to 0.15 mm) Bypass Feeding: 11 lb to ...

  • Canon DR DR-X10C - page 100

    7-3 Chapter 7 Appendix Scanning Speed (LTR/A4 landscape) Black and Whi te 200 dpi Simplex 130 pages/min. Duplex 260 images/min. 300 dpi Simplex 130 pages/min. Duplex 256 images/min. 400 dpi Simplex 82 pages/min. Duplex 82 images/min. 600 dpi (speed priority) Simplex 80 pages/min. Duplex 80 images/min. 600 dpi (image quality priority) Simplex 32 pag ...

  • Canon DR DR-X10C - page 101

    7-4 Chapter 7 Appendix Options Pre-Imprinter Unit (Product Code: 2 418B003) This imprinter u nit prints a text string o n document pages before scanning them. (See “Imprinter (Optional)” on p. 4-8.) Post-Imprinter Unit (Product Code: 2418B00 4) This imprinter u nit prints a text string o n document pages after scanning them. (See “Imprinter ( ...

  • Canon DR DR-X10C - page 102

    7-5 Chapter 7 Appendix External Dimensions 33.90" ( 861 mm) 21.10" (5 36 mm) 22.17" (563 mm) 14.77" ( 375 mm) 17.01" (432 mm) 20.79" (5 28 mm) 5.51" (140 mm) ...

  • Canon DR DR-X10C - page 103

    7-6 Chapter 7 Appendix 2. Option Specifications This section contains the specifications for the sepa rately sold Barcode Module (p. 7-4) and imprinters. Refer to “Using Patchcode Sheets (Option)” (p. 3-19) for the specifications of the patchcodes th at can be detected by the patch code decoder. Barcode Specifications The following barcodes can ...

  • Canon DR DR-X10C - page 104

    7-7 Chapter 7 Appendix Imprinter Specifications Printing Timing Pre-Imprinter: Before scanning Post-Imprinter: After scanning Printing Side Front Position Set in the ISIS/TWAIN driver (See p. 8-26) Pre-Imprinter: One of 6 positions Post-Imprinter: One of 17 positions Printing Content Set in the ISIS/TWAIN driver Imprinter Font Sizes (Dots) 12 × 12 ...

  • Canon DR DR-X10C - page 105

    7-8 Chapter 7 Appendix 3. Index B Background Selection ....... ...................... ......... ............. 4-7 C CapturePerfect 3. 0 ............ ........... ........... ........... ......... 3-15 Cleaning feed roller ... ........... ........... ......... ........... ........... ....... 5-7 glass ........ ........... ........... ......... ...... ...

  • Canon DR DR-X10C - page 106

    7-9 Chapter 7 Appendix Post-Imprinter ... ........... ........... ........... ............ ........ ....... 4-8 Power ............ ......... ........... ........... ........... ......... ........... .. 1-2 turning ON/OFF .................. ........... ........... ........... .. 3-2 Power Switch ......... ........... ........... ........... ........ ...

  • Canon DR DR-X10C - page 107

    User Manual Software Please read this man ual before using the scanner. After you finish reading this ma nual, keep it in a safe place for future reference. ...

  • Canon DR DR-X10C - page 108

    ii Software Table of Contents Chapter 8 ISIS/TWAIN Driver Settings 1. Before You Start Using the Scanner ................ 8-2 2. ISIS/TWAIN Driver Settings Dialog Box ........... 8-4 Basic Tab Sh eet .......... ............. .............. .......... .... 8-5 [Brightness] Tab Sheet ....................... ............... . 8-12 [Image proc essing] ...

  • Canon DR DR-X10C - page 109

    Chapter 8 ISIS/TWAIN Driver Settings 1. Before You Start Using the Scanner.......... ...... 8- 2 2. ISIS/TWAIN Driver Settings Dialog Box .......... 8- 4 Basic Tab Sh eet ... .............. ............. ............. ......... 8-5 [Brightness] Tab Sheet ............ .......... ............. ..... 8-1 2 [Image processing] Tab Sheet ............ ... ...

  • Canon DR DR-X10C - page 110

    8-2 Chapter 8 ISIS/TWAIN Driver Settings 1. Before You Start Using the Scanner To use the DR-X10C with an ISIS/TWAIN-com pliant application program, the DR-X10C must fi rst be selecte d as the sc anner to be used. This section describes how to se lect the scanner using Captur ePerfect 3.0 (an ISIS-compati ble application program). As the scanner se ...

  • Canon DR DR-X10C - page 111

    8-3 Chapter 8 ISIS/TWAIN Driver Settings 4. Select the default page size. IMPORTANT • Clicking the [Default] in the ISIS Dr iver Propertie s dialog box , the setting is applied he re. • For the TWAIN dr iver, the defa ult paper siz e is LTR/A4 and cannot be changed . 5. Click [OK] to finish scanner selection. 6. From the [Scan] menu, select [Sc ...

  • Canon DR DR-X10C - page 112

    8-4 Chapter 8 ISIS/TWAIN Driver Settings 2. ISIS/TWAIN Driver Settings Dialog Box The ISIS/TWAIN Driver Sett ings dialog box consists of the st andard tab sheets [Basic], [Bri ghtness], [Image processing], [Other s], and [Post Imprinter], and the optional ta b sheet [Pre Imprinter]. See the description of each tab sheet for details. ISIS Driver Set ...

  • Canon DR DR-X10C - page 113

    8-5 Chapter 8 ISIS/TWAIN Driver Settings Basic Tab Sheet You can set basi c scan condit ions on the [Ba sic] tab shee t. The items that ca n be set vary dep ending on th e application program you are using . Specify the se ttings as nece ssary for the sc reen that is displaye d. ■ [Basic] Tab Sheet Types The following types of Basic ta b sheets c ...

  • Canon DR DR-X10C - page 114

    8-6 Chapter 8 ISIS/TWAIN Driver Settings ■ [Basic] Tab Sheet Settings You can configure the followi ng setti ngs on the [Basic] tab sheet. User Preference Click [Save] to open the [Sa ve User Preference] dialog box. The [Save User P reference] dialog bo x saves the cur rent settings under an assigned name. You can select the name of a saved set o ...

  • Canon DR DR-X10C - page 115

    8-7 Chapter 8 ISIS/TWAIN Driver Settings [Auto Color Detection] The document is detect ed as black-and-white or color before the scanned image is saved. Selecting this mode enable s the [Setting] button for opening the [Auto Image Type Detection Settings] dialog box, where you can make settings for auto image type detection. (See “[Auto Image T y ...

  • Canon DR DR-X10C - page 116

    8-8 Chapter 8 ISIS/TWAIN Driver Settings Hint • When the [Scan Option s] on the [Ba sic] tab sheet is set to [Scan Singl e Page] for the TWAIN dri ver, the scan ning side is set to [Simp lex] and c annot be chang ed. (See “[ Scan Options ] (TWAIN driver only)” on p. 8 -9.) • Selecting [Skip Blank Pa ge] enable s the [Setting ] button, which ...

  • Canon DR DR-X10C - page 117

    8-9 Chapter 8 ISIS/TWAIN Driver Settings IMPORTANT • Selecting [High-Quali ty Moire Reducti on] produce s high- quality i mages, but the scanning sp eed is slower. • If [High-Quality Moire Reduction] is s elected, [Auto- detection] is selecte d for the document size, the colo r mode is set to [24- bit Color], an d the scann ing side is [Dup lex ...

  • Canon DR DR-X10C - page 118

    8-10 Chapter 8 ISIS/TWAIN Driver Settings ■ Mode-Dependent Function Limitati ons The following tab sheet functi ons are partially disabled according to the se lected mode. For details on the [Brightness] tab sheet settings, see “[Brightness] Tab Sheet” on p. 8-12 . ✔ : av ailable for se tting, – : not ava ilable for setting, or auto ■ [ ...

  • Canon DR DR-X10C - page 119

    8-11 Chapter 8 ISIS/TWAIN Driver Settings ■ [Scan Area] Dialog Box In this dialog box you can define the area of the document page to scan on a selected page size, and register non- standard documen t page sizes. The Scan Area dialog box is different for ISIS and TWAIN drivers: for the TWAIN driver, one of two dialog box types is displayed, depen ...

  • Canon DR DR-X10C - page 120

    8-12 Chapter 8 ISIS/TWAIN Driver Settings Area Window The size indicated for the Ar ea panel corresponds to the page size setting, and the ar ea within the panel indicates the current sca nning area. Hint • The scanning area can be ad justed by dra gging the ha ndles ( ■ ) bordering the Area panel with your mouse. • With Capture Perfect, t he ...

  • Canon DR DR-X10C - page 121

    8-13 Chapter 8 ISIS/TWAIN Driver Settings Hint If all of th e settings on the [Brigh tness] tab sh eet are dis abled, the gamma setting is set to Cus tom. (See “[Gamma Settings] Dialog Box” on p. 8-14.) The availability of brightness and contrast se ttings are as follows, according to the m ode setting on the [Basic] tab sheet. ✔ : av ailable ...

  • Canon DR DR-X10C - page 122

    8-14 Chapter 8 ISIS/TWAIN Driver Settings ■ [Gamma Settings] Dialog Box Use the [Gamma Settings] dialog box to adjust the gamma correction value. [Custom] Check Box Select this check box to se t custom gamma correction. Select Select the side and color for custom setting. Hint The color bar a nd color of the sample image are changed to show the s ...

  • Canon DR DR-X10C - page 123

    8-15 Chapter 8 ISIS/TWAIN Driver Settings [Export] button Clicking this button exports the custom gamma curve settings as a ga mma table file (*.pxg). [Image processing] Tab Sheet The [Image processing] tab shee t provides settings affecting the processing of scanned im ages. Some settings may be disabled, depending on the mode settings on the [Bas ...

  • Canon DR DR-X10C - page 124

    8-16 Chapter 8 ISIS/TWAIN Driver Settings Document Orientati on Specify a rotation angle to correct the orientation of images. Hint Scanned ima ges are rotat ed as follow s, accordin g to the orientation of loade d documen ts and th e selected angle. [Reverse Image] Check Box (TWAIN driver only) Select this check box to out put images scanned in bl ...

  • Canon DR DR-X10C - page 125

    8-17 Chapter 8 ISIS/TWAIN Driver Settings Color drop-out These selecti ons are enable d for scanning modes other than 24-bit Color, so that you can select a primary color (red, green, blue) or gray to be ignored ( dropped out) or enhanced. The [Setting] buttons are enabled when [Drop-out color Custom] or [Custom Color Enha nce] is selected, so that ...

  • Canon DR DR-X10C - page 126

    8-18 Chapter 8 ISIS/TWAIN Driver Settings [JPEG Transfer] Check Box When this check box is sele cted, scanned image data is always compressed to JPEG fo rmat within the scanner for output to the computer. Hint • Scanned im age data is out put from the sc anner as an uncompresse d or JPEG tran sfer, depend ing on instruct ions from the ISI S/TWAIN ...

  • Canon DR DR-X10C - page 127

    8-19 Chapter 8 ISIS/TWAIN Driver Settings [Setting] Button This button is ena bled when [Detect by Ultrasonic] is selected, and displays the [D etect Double Feed Setting] dialog box. In the [Detect Double Feed Setting] dialog box, you can select the sensor position for detection and set a non- detection area s o that the area where a st amp or labe ...

  • Canon DR DR-X10C - page 128

    8-20 Chapter 8 ISIS/TWAIN Driver Settings [Setting] Button This button is enabled when [Au tomatic Feeding] is selected, and allows you to set the delay time from when a loaded document is detect ed until scanning starts. Batch Separation Items availabl e for selection depend on the Feeding Option setting: select batc h separation timi ng (for when ...

  • Canon DR DR-X10C - page 129

    8-21 Chapter 8 ISIS/TWAIN Driver Settings Patchcode Orientation (ISIS driver only) This function is enabled wh en the optional patchcode decoder is installed and ba tch separation is set to [Patchcode]. Set the orie ntation to match that of the patchcode of the patchcode sheet. Hint Settings for various patchc ode types and or ientation s on docume ...

  • Canon DR DR-X10C - page 130

    8-22 Chapter 8 ISIS/TWAIN Driver Settings [Enable Barcode Detection] Check Box Select this check box to de tect barcodes in scanned documents. Hint • Barcode de tection only a pplies to barcodes with in the scanning ar ea. • To detect onl y certain ba rcodes when sca nning document s with multiple bar codes, you c an set the de tection area wit ...

  • Canon DR DR-X10C - page 131

    8-23 Chapter 8 ISIS/TWAIN Driver Settings Code 39 Detect Code 39 barcodes. [Enable] Detect and read Code 39 barcodes. [Full Ascii] Read barcodes in Full ASCII Code. [Checksum] Read the checksum included in barcodes. [Output Checksum] This check box is enabled when [Checksum] is selected, and outputs the read checksum. [Output ST/SP] Select this che ...

  • Canon DR DR-X10C - page 132

    8-24 Chapter 8 ISIS/TWAIN Driver Settings UPC Detect UPC-A/UPC-E barcodes. [Enable] C heck Box Detect and read UP C-A/UPC-E barcodes. [Addon] Set how to handle addon codes included in barcodes. Off: Ignore addon codes. On: Read addon codes. Auto: Detect a nd read addon code s automatically . [Checksum] This check box is enabled when [Checksum] is s ...

  • Canon DR DR-X10C - page 133

    8-25 Chapter 8 ISIS/TWAIN Driver Settings The [Post Imprinter] tab sheet allows you to imprint/add any character string or count er on scanned documents. The [Imprinter] check box is enabled only if the optional pre- imprinter unit is installed. ■ [Pre Imprinter] and [Post Im printer] Tab Sheet Settings You can configure the follo wing settings o ...

  • Canon DR DR-X10C - page 134

    8-26 Chapter 8 ISIS/TWAIN Driver Settings [Double counter with number of characters] abbreviation: <CxCx> A dialog box appears in which to specify the number of characters of the double counter . A counter of the specified number of characters will be imprinted or added on scanned images. [Current time] abbreviation: <TIME> Imprint/add ...

  • Canon DR DR-X10C - page 135

    8-27 Chapter 8 ISIS/TWAIN Driver Settings Orientation Specify the orientation of characters to be impr inted or added. Hint Text orienta tion relative to the feed ing direction is as follows . Imprinte r Font Specify the font size of char acters to be imprinted or added. [Expand character spacing] Select this check box to expand the spacing between ...

  • Canon DR DR-X10C - page 136

    8-28 Chapter 8 ISIS/TWAIN Driver Settings ■ [First Counter] and [Second Counter] Dialog Boxes Make settings for add-on counters. [Start Value] Enter the star t value for th e counter. [Increment] Enter the increment value for the counter . The counter increases by the value entered here. [Increment Trigger] Specifies the type of event that trigge ...

  • Canon DR DR-X10C - page 137

    Chapter 9 Job Registration Tool Settings 1. Before Use ................ .............. .............. ........... 9-2 Job Funct ion.. ............. ............. .......... ............. ....... 9 -2 Starting the Job Registrat ion Tool ........... ............. . 9-2 2. Job Registration Tool ................ ............... ........ 9-3 3. Settings ...

  • Canon DR DR-X10C - page 138

    9-2 Chapter 9 Job Registration Tool Settings 1. Before Use The Job Registration Tool is an application for registeri ng jobs that can be executed from the [Job] key on the control panel. This chapter describes the sett ings for the Jo b Registration Tool. Fo r details o n the Job Function, see “About the Job Function” (see p. 3-14) . Job Functi ...

  • Canon DR DR-X10C - page 139

    9-3 Chapter 9 Job Registration Tool Settings 2. Job Registration Tool The Job Registration Tool consists of the main window below and the [New/Editi ng] and [Admin] dialog boxe s. For details on the dialog boxes, see the description of each dialog box. Menu Bar [Edit] Menu Select a job from the job list, a nd register a new job or edit, copy, or de ...

  • Canon DR DR-X10C - page 140

    9-4 Chapter 9 Job Registration Tool Settings Job List Displays the job numbers (01 to 99) and job titles. Job Information Displays the information for the job selected in the job list. [Close] Button Ends the Job Re gistration Tool. ...

  • Canon DR DR-X10C - page 141

    9-5 Chapter 9 Job Registration Tool Settings 3. Settings Dialog Boxes The settings dialog boxes of the Job Regist ration Tool include the [New/Editing] di alog box and [Admin] di alog box. For details , see the description of each dialog box. [New/Editing] Dialog Box In the [New/Editing] dialog box, you can regist er new jobs and edit registered jo ...

  • Canon DR DR-X10C - page 142

    9-6 Chapter 9 Job Registration Tool Settings Scanner Settin gs Press the [Setting] bu tton to configure scanner settings. [Save to My Pictures folder] Check Box Select this check box to save im age files to the My Pictures folder of the user logged in to Windows. Hint • The name displayed for My Pictures differs depending on th e name of the fo l ...

  • Canon DR DR-X10C - page 143

    9-7 Chapter 9 Job Registration Tool Settings [Access setting] Button This button is enabled when the [Save to My Picture s folder] check box is not selected , and allows you to enter the user name and passwor d required to access the shared network folder specifie d for [Save in folder]. IMPORTANT Access to shar ed network fol ders may be rest rict ...

  • Canon DR DR-X10C - page 144

    9-8 Chapter 9 Job Registration Tool Settings [Compression] Check Box Select this check box to comp ress images save d to files. Black and white (binary) images are compressed in CCITT Group 4 format, and grayscal e and color images in JPEG format. When this check box is not selected, the sav ed files are much larger . Hint • CCITT Gro up 4 is a c ...

  • Canon DR DR-X10C - page 145

    9-9 Chapter 9 Job Registration Tool Settings [Warning Size] Enter the maximum tot al size for all files saved to the specified folder. IMPORTANT • When saving to removable sto rage media such as CD- R, specify the maximum capacit y of the med ia. • When folder monitoring ([Di splay Warning Di alog]) is enable d, a warning me ssage app ears when ...

  • Canon DR DR-X10C - page 146

    Chapter 10 Practical Examples 1. About Basic Condition Settings .................... . 10-2 Confirming the Basic Condit ions for Scanning .... 10-2 2. Practical Examples ................... ............... ...... 10- 4 Scanning Documents of Unregistered Page Sizes ...... ........... ............. ............. .......... ..... 10- 4 Specifying th e ...

  • Canon DR DR-X10C - page 147

    10-2 Chapter 10 Practical Examples 1. About Basic C ondition Settings This chapter prov ides an overview of the basic setting items that ar e the minimum requirements when confi guring the scanne r settings. For detail s on settings, see Chapter 8 “ISIS/TWAIN Driv er Settings Dialog Box” . Confirming the Basic Conditions for Scanning When you s ...

  • Canon DR DR-X10C - page 148

    10-3 Chapter 10 Practical Examples Dots per inch Select the scannin g resolution. Hint Higher resol utions prov ide clearer i mages, but produce large r files. Scanning Side Select which page side(s) to scan. Hint • If the scan ning side is set to [Skip Blank Page], the images o f blank pages ar e deleted when the images are save d. • [Folio] r ...

  • Canon DR DR-X10C - page 149

    10-4 Chapter 10 Practical Examples 2. Practical Examples This section provides an overvie w of which it ems to set accord ing to the purpose when configur ing the scanning settings. For de tails on settings, see Chapter 8 “ISIS/TWAIN Driver Settings Dialog Box” . Scanning Documents of Unregistered Page Sizes Configuring the following sett ings ...

  • Canon DR DR-X10C - page 150

    10-5 Chapter 10 Practical Examples ■ Scanning documents wider than the feeder inlet (Folio Scan) When you want to scan a docum ent that is wider than the feeder inlet, you can scan the docu ment if you fold the document into two, l oad it into the feed tray, and set t he scanning side setti ng to [Folio]. (See p. 4-7.) Hint Folio Scan sup ports u ...

  • Canon DR DR-X10C - page 151

    10-6 Chapter 10 Practical Examples Hint • With the TWAIN driver, lo ad the documen t you want to sp ecify the area of an d press the [Pr eview] butt on to scan th e document an d display t he preview ima ge in the A rea panel. You can then sp ecify the are a from the disp layed prev iew image. • With Capture Perfect 3.0 , the last scann ed imag ...

  • Canon DR DR-X10C - page 152

    10-7 Chapter 10 Practical Examples ■ When you want to skip or enhance intermediate colors Select an in termediate co lor in [Color drop-out] on the [Image processing] tab sheet. The Color Settings dialog box is displayed, and you can specify the color range of th e intermediate colors to ignore (drop out) or enhance. ■ When you want to prevent ...

  • Canon DR DR-X10C - page 153

    10-8 Chapter 10 Practical Examples ■ When you want to chan ge the brightness on the front and back sides to scan a document with front and back sides of different densities. Set the brightness of the back side on the [Brightness] tab sheet. (See p. 8-13.) Hint The brightne ss of the back si de cannot be ch anged when yo u are using adva nced enha ...

  • Canon DR DR-X10C - page 154

    10-9 Chapter 10 Practical Examples ■ When you want to save black and white images and color images separately when scanning a mixture of black and white documents and color documents When documents are scanned while the mode is set to [Auto Color Detection] on th e [Basic] tab shee t, the document colors are det ected and black and white images a ...

  • Canon DR DR-X10C - page 155

    10-10 Chapter 10 Practical Examples ■ When you want to remo ve the black spots from scanned images when scanning documents with punch holes ( when the background is set to black) When the background color is set to black on the [Others] tab sheet, select [Punch Hole Removal] on the [Image processing] tab sheet. The bl ack spots from punch holes i ...

  • Canon DR DR-X10C - page 156

    10-11 Chapter 10 Practical Examples ■ When you want to delete the images of the blank pages in two-sided documents If you set the scanning side sett ing to [Skip Blank Page] on the [Basic] tab sheet, the im ages of blank pages in th e document are deleted. (See p. 8-7.) Hint If [Skip Bla nk Page] is s elected, th e [Setting] button is ena bled, a ...

  • Canon DR DR-X10C - page 157

    CANON ELECTRONICS INC. 1248, SHIMOKAGEMORI, CHI CHIBU-SHI, SAITAMA 369-1892 , JAPAN CANON U.S.A. INC. ONE CANON PLAZA, LAKE SUCCESS, N.Y. 110 42, U.S.A. CANON CANADA INC. 6390 DIXIE ROAD, MISSISSA UGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS CANON LATIN AMERICA, INC. 703 WATE ...

Manufacturer Canon Category Scanner

Documents that we receive from a manufacturer of a Canon DR DR-X10C can be divided into several groups. They are, among others:
- Canon technical drawings
- DR DR-X10C manuals
- Canon product data sheets
- information booklets
- or energy labels Canon DR DR-X10C
All of them are important, but the most important information from the point of view of use of the device are in the user manual Canon DR DR-X10C.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Canon DR DR-X10C, service manual, brief instructions and user manuals Canon DR DR-X10C. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Canon DR DR-X10C.

Similar manuals

A complete manual for the device Canon DR DR-X10C, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Canon DR DR-X10C by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Canon DR DR-X10C.

A complete Canon manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Canon DR DR-X10C - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Canon DR DR-X10C, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Canon DR DR-X10C, that we can find in the current document
3. Tips how to use the basic functions of the device Canon DR DR-X10C - which should help us in our first steps of using Canon DR DR-X10C
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Canon DR DR-X10C
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Canon DR DR-X10C in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Canon DR DR-X10C?

Use the form below

If you did not solve your problem by using a manual Canon DR DR-X10C, ask a question using the form below. If a user had a similar problem with Canon DR DR-X10C it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)