Manual Thermador PH54

38 pages 0.59 mb
Download

Go to site of 38

Summary
  • Thermador PH54 - page 1

    Models PH30 PH36 PH42 PH48 PH54 INST ALLA TION INSTRUCTIONS PH SERIES Professional ® W all Hoods INSTRUCTIONS D'INST ALLA TION Hottes murales de gamme PH Professional ® INSTRUCCIONES DE INST ALACIÓN Campanas de Pared de la Serie PH Professional ® ...

  • Thermador PH54 - page 2

    IMPORT ANT SAFETY INSTRUCTIONS APPROVED FOR ALL RESIDENTIAL APPLIANCES FOR RESIDENTIAL USE ONL Y PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING . IMPORT ANT : Save these Instructions for the Local Electrical Inspector’s use. INST ALLER: Please leave these Instructions with this unit for the owner . OWNER: Please retain these instructions for f ...

  • Thermador PH54 - page 3

    IMPORT ANT SAFETY INSTRUCTIONS Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Do not use an extension cord. If the power cord is too short, have a qualified electrician install ...

  • Thermador PH54 - page 4

    Parts Not Included with your Hood 1. For the most efficient air flow exhaust, use a straight run or as few elbows as possible. 2. Do not use flex ducting. 3. COLD WEA THER installations should have an additional backdraft damper installed to minimize backward cold air flow and a nonmetallic thermal break to minimize conduction of outside temperatur ...

  • Thermador PH54 - page 5

    Appliance Installation The hood can be mounted on a wall or suspended from a cabinet. Both vertical and horizontal discharge are possible with either mounting method. Discharge Direction: The hood is shipped ready for vertical discharge. T o change to horizontal discharge move the discharge cover shown in Figure 1a to the top of the hood. The plate ...

  • Thermador PH54 - page 6

    The hood installation height is the user’s prefer- ence. Figure 2 shows a typical installation of the hood with a duct cover . Accessory 6” and/or 12” duct covers are used to fill the space between the hood and ceiling. The installation height shown in Figure 2 is 36". One 6" duct cover has been used in this installation. Add or sub ...

  • Thermador PH54 - page 7

    Figure 5 Note: Dashed line indicates cutout needed for clearance of the transition. Figure 6 Figure 4 Drywall Cooktop Centerline Screws (2 ea. #14 x 3") A measurement Figure 7 shows the hood configured for vertical discharge. Installations using this type of method require a cutout in the ceiling to accomodate 10" duct and the 1 / 2 " ...

  • Thermador PH54 - page 8

    12 . Before hanging hood, install transition per Figure 6. Fasten transition with two (2) screws (#8 x 3/8 sheet metal, supplied) and tape per all applicable codes. Note: Screws must not hinder damper operation. 1 3. Rest the hood on the screws in the wood bracket. Use the keyholes labeled "I" in Figure 8. Make sure the wood bracket fits ...

  • Thermador PH54 - page 9

    1. In the base of the cabinet drill 1/8" tap holes (See Dimension A in Figure 10 and in T able). Screw in four #10 x 1" screws (provided with hood) leaving 1/4" exposed). 2. If the hood is installed for vertical discharge, use Figure 1 1 to create clearance holes for passage of the transition and conduit (See Dimension B in Figure 1 ...

  • Thermador PH54 - page 10

    Installing an Integral Blower VTN1030C 1. The blower is attached to the hood using weld studs provided on the mounting plate. 2. Figure 12c shows the weld studs in location B for horizont al (rear) discharge. Attach four #10- 24 nuts to the weld studs. For vertical discharge, attach nuts to studs at the top of the mounting plate. 3. Guide the motor ...

  • Thermador PH54 - page 11

    Wire Routing Instruction V ertical Discharge Install wire cover per Figure 12F . The 30"-wide model does not need a wire cover . Horizontal Discharge Install wire cover per Figure 12H. The 30"-wide model does not need a wire cover . Route wires here Figure 12g Route wires here Figure 12e Figure 12f Figure 12h Wire cover Wire cover 10 ...

  • Thermador PH54 - page 12

    The PH hood models are designed to work with VTR630D, VTR1030D, VTR1330E, or VTR1530D remote blowers. For installation instructions see the instructions supplied with the blower unit. 1. Remove the j-box cover . 2. Connect the VTN1030C molex plug connector to the connector present inside the hood as shown in Figure 13. 3. Install 1/2” conduit con ...

  • Thermador PH54 - page 13

    INSTRUCTIONS DE SÉCURITÉ IMPORT ANTES APPROUVÉ POUR T OUT APP AREIL RÉSIDENTIEL POUR UTILISA TION RÉSIDENTILLE SEULEMENT LIRE T OUTES LES INSTRUCTIONS A V ANT DE PROCÉDER L'appareil est lourd et requiert au moins deux personnes ou un équipement approprié pour le déplacer . Les surfaces dissimulées peuvent avoir des bords tranchants. ...

  • Thermador PH54 - page 14

    INSTRUCTIONS DE SÉCURITÉ IMPORT ANTES 2 A TTENTION À des fins de ventilation générale seulement. NE P AS utiliser pour ventiler des vapeurs ou matériaux hasardeux ou explosifs. A TTENTION V entiler l'appareil vers l'extérieur de l'édifice seulement A VERTISSEMENT Une mise à terre inadéquate peut causer un risque de choc él ...

  • Thermador PH54 - page 15

    Pièces non comprises 1. Pour un échappement du débit d'air efficace, utiliser un chemin droit ou ayant le moins de coudes possible. 2. Ne pas utiliser de conduit flexible. 3. Les installation où il F AIT FROID doivent avoir un registre de tirage additionnel installé afin de minimiser un débit d'air froid arrière et une résistance ...

  • Thermador PH54 - page 16

    Installation de l'appareil La hotte peut être installée au mur ou suspendue d'une armoire. Une décharge verticale ou horizontale est possible avec une ou l'autre des méthodes. Direction de la décharge: La hotte est expédiée prête pour une décharge verticale. Pour passer en position horizontale, simplement déplacer le couver ...

  • Thermador PH54 - page 17

    Installation murale La hauteur de l'installation de la hotte est selon les préférences de l'utilisateur . La figure 2 illustre une installation typique avec un couvercle de conduit. Les couvercles de conduit 6 po et/ou 12 po (accessoires) sont utilisés pour remplir l'espace entre la hotte et le plafond. La hauteur de l'instal ...

  • Thermador PH54 - page 18

    Remarque : La ligne pointillée indique la découpe nécessaire pour le dégagement de la transition. Figure 6 La figure 7 montre la hotte configurée pour une décharge verticale. Les installations utilisant ce type de méthode requièrent une découpe dans le plafond pour accomoder un conduit de 10 po et un conduit de 1/2 po pour l'alimentat ...

  • Thermador PH54 - page 19

    1 2 . Avant de suspendre la hotte, installer la transition selon la f igure 6. Fixer la transition avec 2 vis (n° 8 x 3/8 po, à métal, fournies) et apposer du ruban adhésif selon les codes applicables. Remarque : les vis ne doivent pas nuire au fonctionnement du registre 1 3 . Déposer la hotte sur les vis dans la fixation en bois. Utiliser les ...

  • Thermador PH54 - page 20

    La hotte peut être installée sous l'armoire en supportant la hotte par le haut. Remarque : La structure de l'armoire doit être jointe aux montants du mur afin de supporter le poids de la hotte. La figure 10 montre les quatre trous de vis (K) utilisés pour installer la hotte au bas de l’armoire. S’assurer que les deux pastilles enl ...

  • Thermador PH54 - page 21

    Installation de la soufflerie intégrée VTN1030C 1. La soufflerie est fixée à la hotte à l'aide des montants soudés fournis avec la plaque de fixation. 2. La figure 12c montre les montants soudés à l'endroit B pour la décharge (arrière) horizontale. Mettre 4 écrous n° 10 x 24 sur les montants soudés. Pour la décharge vertical ...

  • Thermador PH54 - page 22

    Instructions de câblage 10 Décharge verticale Acheminer fil ici Figure 12f Installer le couvercle comme la figure 12F . Le modèle 30 po de large n'a pas besoin de couvercle de fil. Décharge horizontale Acheminer fil ici Couvercle de fil Figure 12h Installer le couvercle comme à la figure 12H. Le modèle 30 po de large n'a pas besoin ...

  • Thermador PH54 - page 23

    1. Enlever le couvercle de la boîte de jonction. 2. Installer un connecteur de conduit 1/2 po. 3. Acheminer les fils noir , blanc et vert (n° 12 AWG) dans le conduit 1/2 po depuis l'alimentation de la boîte de jonction. 4. Brancher les fils d'alimentation sur les fils de la hotte comme suit : noir avec noir , blanc avec blanc et vert s ...

  • Thermador PH54 - page 24

    1 INSTRUCCIONES IMPORT ANTES DE SEGURIDAD APROBADO P ARA T ODAS LAS UNIDADES RESIDENCIALES ÚNICAMENTE P ARA USO RESIDENCIAL POR F A VOR LEA COMPLEA TMENTE LAS INSTRUCCIONES ANTES DE PROCEDER. IMPORT ANTE: Guarde estas instrucciones para el uso del Inspector Local de Electricidad. INST ALADOR: Por favor deje estas instrucciones con est a unidad par ...

  • Thermador PH54 - page 25

    INSTRUCCIONES IMPORT ANTES DE SEGURIDAD CUIDADO Sólo para uso de ventilación general. NO LO utilice para exhaustar materiales peligrosos o explosivos o vapor . 2 La conexión inapropiada a tierra puede resultar en riesgo de choque eléctrico. Consulte a un electricista calificado si las instrucciones de conexión a tierra no son completamente ent ...

  • Thermador PH54 - page 26

    Partes Incluidas con su Campana Partes No Incluidas con su Campana CONSIDERACIONES ANTES DE INST ALAR LA CAMP ANA 1. Para tener el escape de aire más eficiente, utilice un conducto recto o la menor cantidad de codos posibles. 2. No utilice conductos flexibles. 3. Las instalaciones en CLIMA FRÍO debe contar con un amortiguador extra para la contra ...

  • Thermador PH54 - page 27

    Se puede montar la campana en una pared o en forma suspendida de un gabinete. Con cualquiera de estos dos métodos se puede instalar la descarga vertical u horizontal. Dirección de la Descarga: La campana viene preparada para la descarga vertical. Para cambiar a la descarga horizontal, simplemente cambie la cubierta de descarga que se muestra en l ...

  • Thermador PH54 - page 28

    Instalación con Montaje en Pared Figura 2 - Instalación típica de campana S tandard 8 ft Ceiling (96") 6" Duct Cov er Hood Height (36") Standard 36" high Range 18" 24" Cubierta de conducto de 6" Altura de la campana (36"") Altura al techo estándar de 8 pies (96") (244 cm) Rango estándar 36" ...

  • Thermador PH54 - page 29

    Nota: La línea punteada indica el recorte que se necesita para el espacio libre de la transición. 1 1. Dirección de Descarga: La descarga horizontal requiere un recorte de la pared como se indica en la Figura 5, para proporcionar un espacio libre para la transición. El lugar del recorte se determina por la altura de instalación de la campana. ...

  • Thermador PH54 - page 30

    1 2. Antes de colgar la campana, instale la transición según la Fig. 6. Fije la transición con 2 tornillos (tornillo autorroscante o de plancha #8 x 3/8, incluidos) y encíntela de acuerdo a todos los códigos aplicables. Nota: los tornillos no deben interferir con la operación del regulador de tiro. 1 3. Coloque la campana sobre los tornillos ...

  • Thermador PH54 - page 31

    Instalación con Gabinete Se puede instalar la campana abajo de un gabinete que soporte la campana desde arriba. Nota: EL gabinete debe estar unido estructuralmente a los resaltos de pared para soportar el peso de la campana. La Figura 10 muestra los cuatro agujeros (K) de tornillo que se usan para fijar la campana a la parte inferior del gabinete. ...

  • Thermador PH54 - page 32

    Instalar un Soplador Integral VTN1030C Se puede instalar la campana con un soplador VTN1030C. 1. Quite los soportes de transporte a la izquierda y derecha y deséchelos. 2. Corte la unión de cable como se indica en la Figura 12a. Ubique el arnés de cables con el conector Molex de 6 pines. Coloque el arnés de cables para que salga por la parte tr ...

  • Thermador PH54 - page 33

    Instrucción para encaminar los cables Descarga V ertical Descarga Horizontal Encamine los cables aquí Encamine los cables aquí Figura 12e Figura 12g Figura 12f Figura 12h Cubierta de cable Cubierta de cable Instale la cubierta de cable como se indica en la Figura 12f. El modelo con ancho de 30" no necesita una cubierta para cables. Instale ...

  • Thermador PH54 - page 34

    Conectar la campana con un Soplador Remoto 1. Quite la cubierta de la caja de conexiones. 2. Instale el conector del conducto de 1/2" en la caja de conexiones. 3. Encamine los cables negro, blanco y verde (#12AWG) en el conducto de 1/2" desde la fuente de alimentación a la caja de conexiones. 4. Conecte los cables de la fuente de aliment ...

  • Thermador PH54 - page 35

    Notes ...

  • Thermador PH54 - page 36

    Notes ...

  • Thermador PH54 - page 37

    Notes ...

  • Thermador PH54 - page 38

    5551 McFadden Avenue, Huntington Beach, CA 92649 USA • 800-735-4328 • www .thermador.com 9000165613 • ECO 5U01BP • Rev . C • 03/07 • ©BSH Home Appliances Corporation, 2007 • All rights reserved • Litho in USA We reserve the right to change specifications or design without notice. Some models are certified for use in Canada. Thermad ...

Manufacturer Thermador Category Ventilation Hood

Documents that we receive from a manufacturer of a Thermador PH54 can be divided into several groups. They are, among others:
- Thermador technical drawings
- PH54 manuals
- Thermador product data sheets
- information booklets
- or energy labels Thermador PH54
All of them are important, but the most important information from the point of view of use of the device are in the user manual Thermador PH54.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Thermador PH54, service manual, brief instructions and user manuals Thermador PH54. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Thermador PH54.

A complete manual for the device Thermador PH54, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Thermador PH54 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Thermador PH54.

A complete Thermador manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Thermador PH54 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Thermador PH54, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Thermador PH54, that we can find in the current document
3. Tips how to use the basic functions of the device Thermador PH54 - which should help us in our first steps of using Thermador PH54
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Thermador PH54
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Thermador PH54 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Thermador PH54?

Use the form below

If you did not solve your problem by using a manual Thermador PH54, ask a question using the form below. If a user had a similar problem with Thermador PH54 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)