-
Directed Electronics Tube Driver System TD275/2150 - page 1
CONGRA TULA TIONS ENDP ANEL LA Y OUT FEA TURES / SPECIFICA TIONS ENDP ANEL LA Y OUT (cont.) INST ALLA TION TR OUBLESHOO TING WIRING TROUBLESHOO TING (cont.) PO WER / GROUND TROUBLESHOO TING (cont.) CONNECTIONS TROUBLESHOO TING (cont.) CONNECTIONS (cont.) SYSTEM DIA GRAM 1 / 2 INPUTS / CONNECTIONS BLOCK DIA GRAM INPUTS W ARRANTY CONTENTS (c lick on ...
-
Directed Electronics Tube Driver System TD275/2150 - page 2
The extended use of a high powered audio system may result in hearing loss or damage. While TUBE DRIVER systems are capable of "Concer t Le v el" volumes with incredible accuracy , they are also designed for you to enjoy at more reasonable levels all of the sonic subtleties created by musicians. Please observe all local sound ordinances. ...
-
Directed Electronics Tube Driver System TD275/2150 - page 3
1 TD275 75 WRMS x 2 @ 4 Ohms per channel 150 WRMS x 2 @ 2 Ohms per channel 300 WRMS x 1 @ 4 Ohms bridged TD 2150 150 WRMS x 2 @ 4 Ohms per channel 300 WRMS x 2 @ 2 Ohms per channel 600 WRMS x 1 @ 4 Ohms bridged Dimensions Length = 15.5 Length = 16.75” Height = 3.2” Height = 3.2” Width = 9.25” Width = 9.25” Continuous Output P o wer TD275 ...
-
Directed Electronics Tube Driver System TD275/2150 - page 4
2 Fuse Requirements Recommended Fuse Rating f o r TD275 i s 6 0 Amps Recommended Fuse Rating f o r TD2150 i s 10 0 Amps Y ou will need to install an in-line fuse or circuit breaker in the po wer wire within 18” of the battery . This fuse or circuit breaker pr otects y our vehic le fr om fire in case the power wire shorts to the vehic le body . If ...
-
Directed Electronics Tube Driver System TD275/2150 - page 5
3 W arning! Amplifiers Generate Heat! Y ou can mount the TU B E D RIVER in any position, even upside-down. However , y ou must maintain pr oper airflow . Do not install your TU B E D RIVER under carpets or enclose it behind airtight panels. In trunk-mounted applications, be sure to provide venting for air circulation. Let the amplifier breathe . Wi ...
-
Directed Electronics Tube Driver System TD275/2150 - page 6
4 W arning! T o prevent a short to ground, disconnect the negative (-) terminal of the system’s battery before you begin. If the power cable shorts to ground, current will continue to flow until the short is opened, the main fuse blows, the battery explodes, or the wire melts. Reconnect the terminal only after y ou make all connections. Gr oundin ...
-
Directed Electronics Tube Driver System TD275/2150 - page 7
5 Follow these simple instructions and refer to the dia gram belo w to make your speaker connections: • Using at least 16 gauge wire, run wire from the speakers to the amplifier(s) using the same precautions that you followed for running the power , ground, and remote wires • Cut off excess wire • Use wire strippers to strip 1/4 inch of insul ...
-
Directed Electronics Tube Driver System TD275/2150 - page 8
6 Y ou can operate each pair of channels in both stereo and mono (3 channel or tri-mode) at the same time by using highpass filters (bass blockers) on the higher frequency stereo channels, and a lowpass filter (coil) on the subwoofers. The frequencies of the chosen highpass and lowpass filters must not overlap (allow the mids and highs to play the ...
-
Directed Electronics Tube Driver System TD275/2150 - page 9
7 Input Jac ks The TU B E D RIVER includes both RCA and Mini-Din (balanced) inputs. The supplied RCA connections allow you to use TU B E D RIVER with other brands of audio gear . Our Diff erential RCA inputs provide a dr amatic improv ement in noise reduction ov er standard RCA input types. Our fully balanced Mini-DIN connection system f eatures hi ...
-
Directed Electronics Tube Driver System TD275/2150 - page 10
8 Input Gain Contr ol There is an Input Gain Control located on the end panel under the RCA input jacks. This is not a v olume contr ol! This control matches the output signal voltage of the source unit to the amplifier inputs. By turning the control clockwise (to the right), the inputs of the amplifier become more sensitive and will allow a weak s ...
-
Directed Electronics Tube Driver System TD275/2150 - page 11
9 P ower Side 1 3 2 1. PO WER A red light indicates that the amplifiier is turned on (After warm-up sequence). 2. W ARM UP A red light indicated that the tubes are warming up. (Refer to Pg. 4; Remote T urn-on) 3. PO WER / GROUND After you have securely connected your power and ground wires, plug in the connector here. B A CK T O CONTENTS ...
-
Directed Electronics Tube Driver System TD275/2150 - page 12
10 Input/Contr ol Side 7 15 4 3 2 6 1. SPEAKER OUTPUTS/REMO TE(T urn on) After connecting remote and speaker wires plug in the connector here. 2. GAIN CONTROL Use this control to match the output level of the head unit to the outputs of the amplifier 3. INPUTS Plug in the RCA outputs from your head unit here. 4. BALANCED / RCA This switch is used t ...
-
Directed Electronics Tube Driver System TD275/2150 - page 13
11 No Sound Amplifier T urning Down at Normal V olume Do you have 12V at the amplifier ’s connections? Is the W ARM UP LED illuminated? YES NO YES The warm up cycle can take up to 40 sec., Is there sound after that? NO Y ou’re done Is there signal on the RCA ’s? YES NO Does the amp remote (REM) have 12V? Check all connections. Repair as neede ...
-
Directed Electronics Tube Driver System TD275/2150 - page 14
12 No Sound in One Channel Amplifier T urning D o w n at High V olume YES Reverse the left and right inputs. Check the pre-amp (RCA/Mini-Din) cables for open connections and make corrections. Did you find open connections? NO Y ou’re done SOUND IS NO W IN... Opposite Channel Problem is in the speaker or speaker wire of the silent channel. Check s ...
-
Directed Electronics Tube Driver System TD275/2150 - page 15
Noises While the Engine is On Alternator whine: This noise changes in frequency with engine RPM. Check for: . Excessive input le vel setting on the amplifier . High resistance in cabling or corr oded and/or loose connections . P olarity of the input cables If the problem persists, check the whines and pops checklist below . Ticks/b uzz: This noise ...
-
Directed Electronics Tube Driver System TD275/2150 - page 16
14 Noises While the Engine is On or Off System hiss: Distor tion: System hiss is a white noise that occurs even when the engine is of f. It is usually due to excessively high gain settings. If the hiss is still audible when you disconnect the input cables from the amplifier , check the input level on the amplifier . If the hiss disappears when you ...
-
Directed Electronics Tube Driver System TD275/2150 - page 17
15 eject VOLUME BASS TREBLE RIGHT LEFT BALANCE TRA CK REVERSE FOWARD 1 2 3 4 8 7 6 5 PPI MAR KET ING DPT Trk 1 LD3 Studio Driver 12" 4 ohm Woofer (Bridged) HIgh Pass Low Pass Source Unit TD215 0 TD275 LDX33 Studio Driver System 2 B A CK T O CONTENTS ...
-
Directed Electronics Tube Driver System TD275/2150 - page 18
16 AMP RCA Right Input DIF. RCA Left Input INPUT ATTENUATION AMP Left Right MINI-DIN Input DIF. GAIN GAIN Left Right BALANCED/RCA Switch BALANCED/RCA Switch B A CK T O CONTENTS ...
-
Directed Electronics Tube Driver System TD275/2150 - page 19
Three-Y ear Limited U .S.A. W arranty This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. TUBE DRIVER warrants its products to be free from defects in materials and workmanship under normal use and service for a period of three (3) years from the date of original purchase when the unit i ...
Do you have a question concerning Directed Electronics Tube Driver System TD275/2150?
Use the form below
If you did not solve your problem by using a manual Directed Electronics Tube Driver System TD275/2150, ask a question using the form below. If a user had a similar problem with Directed Electronics Tube Driver System TD275/2150 it is likely that he will want to share the way to solve it.