English dropdown-ico

Manual Craftsman 917.27623

60 pages 3.79 mb
Download

Go to site of 60

Summary
  • Craftsman 917.27623 - page 1

    Owner's Manual CRIIFTSMIIH ° GARDEN TRACTOR 25.0 HP, 54" Mower Electric Start 6 Speed Transaxle Model No. 917.276230 This product has a low emission engine which operates I_ differently from previously built engines. Before start the you engine, read and understand this Owner's Manual, IMPORTANT: Read and follow all Safety Rules and ...

  • Craftsman 917.27623 - page 2

    Warranty ................................................ 2 Safety Rules .......................................... 3 Product Specifications ........................... 5 Assembly/Pre-Operation ....................... 7 Operation ............................................. 12 Maintenance Schedule ........................ 18 Maintenance .......... ...

  • Craftsman 917.27623 - page 3

    IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death. _IWARNING: In order to prevent ac- cidental starting when setting up, trans- porting, adjusting or making repairs, always disconnect spark plug wire and place w ...

  • Craftsman 917.27623 - page 4

    II. SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents,which can result in severe injury or death. Opera- tion on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. • Mow up and down slopes, not across. • Watch for holes, ruts, bumps, rocks, or ...

  • Craftsman 917.27623 - page 5

    • Remove gas-powered equipmentfrom the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipmentwith a portable container, rather than from a gasoline dispenser nozzle. • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.Do not use a nozzl ...

  • Craftsman 917.27623 - page 6

    PRODUCT SPECIFICATIONS Gasoline Capacity 5 Gallons and Type: Unleaded Regular Oil Type SAE 10W30 (above 32°F (API-SG-SL): SAE 5W30 (below 32°F) Oil Capacity: W/Filter: 4.0 Pints W/O Filter: 3.5 Pints Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Lo: Hi: 0.7 1.7 1.4 3.3 2.3 5.4 Reverse: 0.9 2.1 Tire Pressure: Front: 14 PSI Rear ...

  • Craftsman 917.27623 - page 7

    Steering Wheel Steering Wheel Insert Steering Steering Wheel Sleeve Adapter Gauge Wheels //q (4) Adjusting _1 , Bar JJ_J (double loop) (4) Washers 3/8 x 3/4 x 14 Ga. (4) Locknut 3/8-16 4, Whees( 'O (4) Clevis Pins (4) Shoulder Bolt (1) Washer @ 17/32 x 1-3/16 x 12 Gauge (1) Knob Mower (2) Retainer Springs (double loop) (2)Flanged Pins (1) Oil ...

  • Craftsman 917.27623 - page 8

    Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY A socket wrench se ...

  • Craftsman 917.27623 - page 9

    INSTALL SEAT Adjust seat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. 2. Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard. 3. Place seat on seat pan so head of shoulder bolt is positioned ...

  • Craftsman 917.27623 - page 10

    ASSEMBLE GAUGE WHEELS TO MOWER DECK The gauge wheels are designed to keep the mower deck in proper position when operating mower. 1. Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center Iocknuts and tighten securely ...

  • Craftsman 917.27623 - page 11

    Belt Tension Rod Disengaged Position Gauge Wheel g Bracket Electric Clutch Pulley Front Plate Assembly Double Loop Retainer Springs ..P Front Mower Bracket Flanged Pin- Position Notch Vertically Rear Mower Pins CHECKTIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Cor- rect tire pressure is important f ...

  • Craftsman 917.27623 - page 12

    These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H I'.,I REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW IGNITION SWITCH ENGINE OFF REVERSE ENGINE ON ENGINE START PARKING BRAKE PARKING BRAKE PARKING BRAKE OPERATION LOCKED UNLOCKED SYSTEM (ROS) oi OVER TEMP LIGHT t FUEL OIL PR ...

  • Craftsman 917.27623 - page 13

    KN OW YOU R TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Ammeter Throttle Control Ignition Switch "ON" Position Attachment Clutch Switch L ...

  • Craftsman 917.27623 - page 14

    The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR TO SE ...

  • Craftsman 917.27623 - page 15

    1. Lower mower and adjust mower to de- sired cutting height(See "TO ADJUST MOWER CUTTING HEIGHT" in this section of manual). 2. Remove retainer spring and clevis pin which secure each gauge wheel bar. 3. Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge whe ...

  • Craftsman 917.27623 - page 16

    USING THE REVERSE OPERATION SYSTEM - 1. Depress clutch/brake pedal all the way down and hold. 2. With engine running, turn ignition key counterclockwise to ROS "ON" posi- tion. 3. Look down and behind before backing. 4. Move gear shift lever to reverse (R) po- sition and slowly release clutch/brake pedal to start movement. 5. When use of ...

  • Craftsman 917.27623 - page 17

    TO START ENGINE When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. 1. Sit on seat in operating position, depress clutch/brake pedal and set parking brake. 2. Place gear shift lever in neutral (N) position. 3. Move attachment clutch to disengage ...

  • Craftsman 917.27623 - page 18

    MAINTENANCE SC.EOU'E FILL IN BATES AS ¥O0 COMPLETE REGULAR SEBV,CE / 74 TSERV'OE OATES Check Brake Operation _4 Check Tire Pressure Check Operator Presence and T ROS Systems _' R Check for Loose Fasteners I_ Ks A Sharpen/Replace Mower Blades 1_3 C Lubrication Chart _ 0 Check Battery Level R Clean Battery and Terminals Check Transaxl ...

  • Craftsman 917.27623 - page 19

    TRACTOR AIways observe safety ruleswhen per- forming any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual). TIRES ...

  • Craftsman 917.27623 - page 20

    • Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced. Center Holej / or Pin _ade BATTERY Your tractor has a battery charging ...

  • Craftsman 917.27623 - page 21

    5. Remove the drain tube and store in a safe place. 6. Refill engine with oil throughoil fill dip- stick tube. Pour slowly. Do not overfill. For approximate capacity see "PROD- UCT SPECIFICATIONS" section of this manual. 7. Use gauge on oil fill cap/dipstick for checking level. Insert dipstick into the tube and rest the oil fill cap on th ...

  • Craftsman 917.27623 - page 22

    CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and transmis- sion are covered to keep water out ...

  • Craftsman 917.27623 - page 23

    TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PRODUCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower. SIDE-TO-SIDE ADJUSTMENT • Raise mower to its highest position. • Measure ...

  • Craftsman 917.27623 - page 24

    TO REPLACE MOWER DRIVE BELT MOWER DRIVE BELT REMOVAL 1. Park tractor on a level surface. Engage parking brake. 2. Lower attachment lift lever to its lowest position. 3. Disengage belt tension rod from lock _bracket. CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and re- lease slowly. 4. Remove screws from R.H. and L.H. mandrel ...

  • Craftsman 917.27623 - page 25

    TO ADJUST ATTACHMENT CLUTCH The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required. Adjustments should be made by a Sears or other qualified service center. 1. Mak ...

  • Craftsman 917.27623 - page 26

    Clutching Flat Clutchin( Above Mids Engine Belt Keep.er Pulley V-Idler Transaxle Pulley Twists Belt Keeper Bottom TO ADJUST STEERING WHEEL ALIGN- MENT If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely. FRONT W ...

  • Craftsman 917.27623 - page 27

    4. Install new battery with terminals in same position as old battery. 5. Reinstall terminal guard. 6. First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown.Tighten securely. 7. Connect BLACK grounding cable to negative (-) battery terminal with re- maining hex bolt and keps nut.Tighten securely 8. Clo ...

  • Craftsman 917.27623 - page 28

    TO ADJUST CHOKE CONTROL The choke control has been preset at the factory and adjustment should not be nec- essary, check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows: 1. With engine not running, move choke control (located on dash panel) to full choke position. 2. Remove air cleaner cover, f ...

  • Craftsman 917.27623 - page 29

    Immediately prepare your tractor for stor- age at the end of the season or if the trac- _91_,wAWill not be used for 30 days or more. RNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. TRACTOR Remove mower from tractor for ...

  • Craftsman 917.27623 - page 30

    TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Will not start CAUSE Hard to start Engine will not turn over Engine clicks but will not start 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter. 6. Dirty fuel filter. 7 Water in ...

  • Craftsman 917.27623 - page 31

    TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Loss of power 1. Cutting too much grass/too 1. Raise cutting height/reduce fast. speed. 2. Throttle in "CHOKE" position. 2. Adjust throttle control. 3. Build-up of grass, leaves 3. Clean underside of mower and trash un ...

  • Craftsman 917.27623 - page 32

    TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION 1. Remove obstruction. Mower blades will not rotate Poor grass discharge Headlight(s) not working (if so equipped) Battery will not charge Engine "backfires" when turning engine "OFF" 1. Obstruction in clutch ...

  • Craftsman 917.27623 - page 33

    SCHEMATIC 02842 -193394 TRACTOR - - MODEL NUMBER 917.276230 EHP RCS LT W_TH BYPASS SWITCH / ELECTRIC CLUTCH SOLENOID AMMETER FUSE (OPTIONAL) WH{TE PTO .............................. i(DISENGAGED ) i ....... b N L O b_/ SPARK PLUGS IGNITION GAP 0 2 PLUGS UNIT J O_N TWI_ CYL. ENGINES) FUELSHUT-OFF q METER p 0 SOLENOID I I (OPTIONAL) FUEL I __1 LINE i ...

  • Craftsman 917.27623 - page 34

    ELECTRICAL TRACTOR - - MODEL NUMBER 917.276230 40 96 34 J 52 I / / / j/ i 193394B_ 34 ...

  • Craftsman 917.27623 - page 35

    ELECTRICAL TRACTOR - - MODEL NUMBER 917.276230 KEY PART NO. NO. DESCRIPTION 1 144927 Battery 2 74760412 Bolt Hex Head 1/4-20 x 3/4 8 7603J Tray, Battery 10 145211 Bolt 1/4-20 x 7.5 Zinc 11 150109 Hold down Battery Dash Mount 12 145769 Nut Push Nylon 1/4" 16 176138 Switch interlock Push-in 21 175688 Harness Socket Light W/4152J 22 4152J Bulb Li ...

  • Craftsman 917.27623 - page 36

    TRACTOR - - MODEL NUMBER 917,276230 CHASSIS AND ENCLOSURES 14 130 28 21 2 _20 19 chassis-stealth II 3-vgt 31 17 16 148 _156 130 139 6 17 122 150 122 156 172 146 143 14__130 17 50 44 17 17 / 17 85 86 7O 17 169 t_ 84 17 17 63 60__ 24 17 _66 36 ...

  • Craftsman 917.27623 - page 37

    TRACTOR - - MODEL NUMBER 917,276230 CHASSIS AND ENCLOSURES KEY PART KEY NO. NO. DESCRIPTION NO. 1 180375 Rail, Frame RH 68 2 175282 Drawbar, Gt 70 4 73680700 Nut, Crownlock Hex 7/16-14 unc 84 5 193636X428 Dash 85 6 157882 Dash, Lower Vgt One Piece 86 7 17720408 Screw, Thd Cut 1/4-20 x 1/2 88 8 184668 Support, Battery 91 14 175260X428 Hood Asm 106 1 ...

  • Craftsman 917.27623 - page 38

    TRACTOR - - MODEL NUMBER 917,276230 GROUND DRIVE 39_ 42 40 41 [ 38 36 :,, _ 37 6 / 29 " _ 68 64" J 35_ 117_ 37 38 34 24 69 52 65 48 57 157 155 54 66 15 23 67 drive 9-vgt 62 38 ...

  • Craftsman 917.27623 - page 39

    TRACTOR - - MODEL NUMBER 917.276230 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 3 7563R Washer, Thrust, Axle 39 74321016 Screw, Fin. #10-24 x 1 4 17490508 Screw Thdrol 5/16-18 x 3/4 40 178575 Actuator, Interlock Switch 5 STD541437 Nut, Crownlock 3/8-16 41 73931000 Nut, Centerlock #10-24 6 STD561210 Pin, Cotter 42 8883R Co ...

  • Craftsman 917.27623 - page 40

    TRACTOR - - MODEL NUMBER 917.276230 STEERING ASSEMBLY 23 34 33 32 6 29 28 36 15 1313 / i I _, 1 I I i I I I I Ill k I 8 < J 18"X__// steering 20-vgt 52 J J 4O ...

  • Craftsman 917.27623 - page 41

    TRACTOR - - MODEL NUMBER 917.276230 STEERING ASSEMBLY KEY PART NO. NO. 1 186093X428 2 178557 3 183226 4 161849 5 161848 6 6266H 7 121748X 8 12000029 9 184946X505 10 74781044 11 136518 12 73901000 13 121749X 14 STD551137 15 73540600 16 186814 18 187799 19 156011 20 163887X428 21 186737 22 155105 23 152927 26 186095X428 27 3366R 28 17000612 29 104239 ...

  • Craftsman 917.27623 - page 42

    ENGINE TRACTOR - - MODEL NUMBER 917,276230 I 18 15 2O 37 84 85 84 12 11 82 69 _62 i I i 26 engine-kohler22 17-vgt 27 28 39 9 8 40 29 SPARK ARRESTER KIT KEY PART NO. NO. 1 2 149723 8 121361X 9 177748 10 175287 11 179335 12 143996 15 179115 18 179124X428 20 177328X428 21 191611 22 187768X428 26 3645J 27 139277 28 188669 29 137180 37 123487X 39 174906 ...

  • Craftsman 917.27623 - page 43

    TRACTOR - - MODEL NUMBER 917.276230 SEAT ASSEMBLY 14_ 10 _J i 5 4 18 u ° 19 12 I I I seat 1-vgt KEY NO. 1 2 3 4 5 6 7 8 10 12 13 PART NO. 188714 140551 140675 127018X 145006 STD541437 124181X 171877 182493 174648 121248X DESCRIPTION Seat Bracket, Pivot Seat Strap, Asm Fender Bolt Shoulder 5/16-18 x .62 Clip, Push In, Hinged Nut, Crownlock 3/8-16 u ...

  • Craftsman 917.27623 - page 44

    DECALS TRACTOR - - MODEL NUMBER 917,276230 18 19 17 lO 16 12 23 KEY PART NO. NO. 1 177665 2 178455 3 194023 4 194024 5 194026 6 133644 7 193609 8 185980 9 194027 10 156439 11 181249 12 146047 13 178482 14 188298 13 14 KEY PART DESCRIPTION NO. NO. Decal, Dash Panel, Lower 15 191202 Decal, Deck Caution 16 177914 Decal, Hood, RH 17 149516 Decal, Hood, ...

  • Craftsman 917.27623 - page 45

    LIFT ASSEMBLY 40 39 42 TRACTOR - - MODEL NUMBER 917,276230 43 35 73 38 34 29 72 31 32 30 10 3 1 6 85 ¸ 7O KEY NO. 1 2 3 4 5 6 7 8 10 11 12 23 24 26 29 3O 31 32 33 34 PART NO. 121006X 180045 159189 12000022 19292016 71110624 175830 175831X505 183894 175375 163552 STD624008 73350800 73800800 150233 110807X 19131016 137150 76020308 137167 12 ¢ ...

  • Craftsman 917.27623 - page 46

    MOW_ R DECK _p.AC_OP"" "_v,.,v-- 46 5 57 56 33 6O 25 Z7 rno,_er_deok'54-_ 46 ...

  • Craftsman 917.27623 - page 47

    TRACTOR - - MODEL NUMBER 917.276230 MOWER DECK KEY PART NO. NO. DESCRIPTION 1 187295 Deck Weldment Mower 5 STD624008 Retainer Spring 6 187297 Cover Mandrel LH 7 188187 Cover Mandrel RH 8 174365 Bolt 7/16 Asm. Blade 11 187254 Blade, Standard (For mulching mowers only) 13 187291 Shaft Asm. w/Lower Bearing 14 187281 Housing, Mandrel 15 110485X Bearing ...

  • Craftsman 917.27623 - page 48

    TRANSAXLE TRACTOR - - MODEL NUMBER 917,276230 8O 14 + 74 7O 84 99 ___66 85 _Q 87 _ 88 _l 90 -_ 91_@ 94 "_o 73 25 24 48 ...

  • Craftsman 917.27623 - page 49

    TRANSAXLE TRACTOR - - MODEL NUMBER 917,276230 KEY PART NO. NO. 1 4197R 2 12000034 3 4199R 4 4216R 5 4215R 6 4217R 7 174728 8 74020652 9 7392M 10 137261 11 4985R 12 6266H 13 4212R 14 137125 15 6276H 16 633A63 17 8118M 18 8740H1 19 122238X 20 4218R 21 6252H1 22 7810H 23 6262H 24 7393R 25 992R1 26 139111 27 4986R 28 122254X 29 6269H 30 5855H 31 174731 ...

  • Craftsman 917.27623 - page 50

    TRACTOR - - MODEL NUMBER 917,276230 KOHLER ENGINE-MODEL NUMBER CV730-0029 .'YLINDER HEAD, VALVE AND BREATHER I j6 3 3O 5 4 28 27_'_ CRANKCASEJ 2,4® 022 20 @/18 15/° 10 23,_@_ /25 / _,_ /2_ 24 26 6- X_-7 _J 7 4 14 15 _ 117 /1 J i _ _: /3 14 I Q 11 _--4 12 j_ 5O ...

  • Craftsman 917.27623 - page 51

    TRACTOR - - MODEL NUMBER 917.276230 KOHLER ENGINE-MODEL NUMBER CV730-0029 HEAD/VALVE/BREATHER CRANKCASE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1. 24-033-03-S 2. 24-041-50-S 3. 24-096-87-S 4. M-645020-S 5. 25 139 60-S 6. 25-351-01-S 7. 24-755-66-S 8. 24-411-05-S 9. 24-841-03-S 10, 24-318-72-S 11, 25-186-01 -S 12. 24-599-01-S 13. 1 ...

  • Craftsman 917.27623 - page 52

    TRACTOR - - MODEL NUMBER 917,276230 KOHLER ENGINE-MODEL NUMBER CV730-0029 IGNITION/ELECTRICAL I / 20_ 19--'_ 7 , 16_ 17- t AIR INTAKE ] BLOWER HOUSING AND BAFFLESJ 7 6 3 52 ...

  • Craftsman 917.27623 - page 53

    TRACTOR - - MODEL NUMBER 917.276230 KOHLER ENGINE-MODEL NUMBER CV730-0029 IGNITION/ELECTRICAL BLOWER HOUSING & BAFFLES KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1. 54-755-15-S Kit, grass screen (Includes 2-4, & 24-113-18-S) 2. M-403025-S Screw, hex. cap M4x0.7x25 (4) 3. X-25-92-S Washer, plain 5/16" (4) 4. 24-112-04-S Spacer, grass ...

  • Craftsman 917.27623 - page 54

    TRACTOR - - MODEL NUMBER 917,276230 KOHLER ENGINE-MODEL NUMBER CV730-0029 STARTING SYSTEM I _--6 @ 7 ENGINE CONTROLS J / 25 26 OIL PAN / LUBRICATION J Ot _8 18/_ 11 J_ 187_ 17 o_ _ 0 16 54 ...

  • Craftsman 917.27623 - page 55

    TRACTOR - - MODEL NUMBER 917.276230 KOHLER ENGINE-MODEL NUMBER CV730-0029 STARTING SYSTEM OIL PAN/LUBRICATION KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1. M-839080-S Screw, hex. flange 1. M8x1.25x80 (2) 2. 25-098-09-S Starter, solenoid shift (In 2. cludes 3-7) 3. 25 086 113-S Screw, external torx hd. (3) 3. 4. 25-435-05-S Kit, solenoid (Include ...

  • Craftsman 917.27623 - page 56

    TRACTOR - - MODEL NUMBER 917,276230 KOHLER ENGINE-MODEL NUMBER CV730-0029 CRANKSHAFT I ml EXHAUST J FUEL SYSTEMJ / 1 4 7 / 7 ;10 o d 1 7 8 14 (_F 7 7 _/_ 7 11 12 13 56 ...

  • Craftsman 917.27623 - page 57

    TRACTOR - - MODEL NUMBER 917.276230 KOHLER ENGINE-MODEL NUMBER CV730-0029 CRANKSHAFT KEY PART NO. NO. DESCRIPTION 1. 24-014-72-S Crankshaft (includes 2) 2. 52-139-09-S Plug, cup EXHAUST KEY PART NO. NO. DESCRIPTION 1. 24-041-49-S Gasket, exhaust (2) 2. 25-072-04-S Stud, MSx1.25x33 (4) - - 24-522-332 Short Block - - 24-782-23 Miniblock -- 24-755-113 ...

  • Craftsman 917.27623 - page 58

    SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION GO .-=.,.. *=.,.. ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. _b ARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Ex ...

  • Craftsman 917.27623 - page 59

    59 ...

  • Craftsman 917.27623 - page 60

    Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage do ...

Manufacturer Craftsman Category Lawn Mower

Documents that we receive from a manufacturer of a Craftsman 917.27623 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 917.27623 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 917.27623
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 917.27623.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 917.27623, service manual, brief instructions and user manuals Craftsman 917.27623. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 917.27623.

Similar manuals

A complete manual for the device Craftsman 917.27623, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 917.27623 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 917.27623.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 917.27623 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 917.27623, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 917.27623, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 917.27623 - which should help us in our first steps of using Craftsman 917.27623
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 917.27623
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 917.27623 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 917.27623?

Use the form below

If you did not solve your problem by using a manual Craftsman 917.27623, ask a question using the form below. If a user had a similar problem with Craftsman 917.27623 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)