English dropdown-ico

Manual Hearth and Home Technologies SL-350TRSI-AUE

38 pages 2.14 mb
Download

Go to site of 38

Summary
  • Hearth and Home Technologies SL-350TRSI-AUE - page 1

    1 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 MODEL: SL-350TRSI-AUE AUSTRALIAN GAS ASSOCIA TION APPROVED Approval Number 5666 THIS MANUAL MUST BE USED FOR INST ALLA TION AND RET AINED BY HOMEOWNER FOR OPERA TION AND MAINTENANCE. HEA T & GLO, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakevill ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 2

    2 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 IMPORT ANT : Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty . Save this Manual for future reference. MODEL SL-350TRSI-AUE IS AUSTRALIAN GAS ASSOCIA TION AP ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 3

    3 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 T ABLE OF CONTENTS 1.0 Installation Instructions ......................................................................................... 5 1. 1 Introduction ................................................................................................... 6 1.2 Flue System Approva ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 4

    4 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 1. Diagram of SL-350TRSI-AUE 22 -3/4 i n. (57 7 mm) 1 1-3 /8 in. (28 9 mm) 16 - 3 /8 i n. (414 mm) 8-3/ 4 in . (223mm) 15 - 7 /8 i n. (402 mm ) Ø 6-5/ 8 in . (16 7 mm) 24 in. (610mm) 5-5/8 in. (144 mm ) GAS L IN E ACC ESS 41-3/4 i n. (1060mm) 21 -3/8 i n. (542mm) 2- 1/8 i n. ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 5

    5 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 2. Fireplace Dimensions, Locations, and Space Requirements 1.0 INST ALLA TION INSTRUCTIONS Clearance Requirements The top and back of fireplace are defined by stand-offs. The heat shield must be attached as shown if combus- tible materials are placed directly on top standoffs ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 6

    6 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 4. Framing Dimensions Framing should be constructed of 2 X 4 lumber or heavier . The framing headers may rest on the fireplace stand-offs. AB C D * E * 34" 30-5/8" 16 1/2" 41-3/4" 21-1/4" (864mm) ( 778mm) (419mm) (1060mm) (540mm) *NOTE: The center of t ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 7

    7 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 NOTES: 1. All distances are measured vertically or horizontally along the wall to a point in line with the nearest part of the terminal. 2. Prohibited area below electricity meter or fuse box extends to ground level. 3. See clause 5.13.6.6 for restrictions on a flue terminal under a ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 8

    8 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 TABLE 1 1.2 FLUE SYSTEM APPROV ALS These models have flue starting collars on both the top and the back of the unit. Depending upon the installa- tion, decide which ONE set of starting collars will be used to attach the flue system. The starting collar sealing cap must remain on the ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 9

    9 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 NOTE: PIPES OVERLAP 32mm A T EACH JOINT . D V P 9 0 S T 319m m 286m m 184mm 32mm T YP 13mm T YP 217mm DVP 36 DVP48 1219m m 610m m 914m m 102mm 152mm DVP4 DVP6 305m m DVP 12 51mm MIN . DVP12A 310m m MAX. DVP24 251m m 45.0 O 260mm DVP 45 362mm Figure 7. DVP-Series Balanced Flue Compone ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 10

    10 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 8. SL D-Series Balanced Flue Component S pecifications (102mm inner pipe / 168mm outer pipe) NOTE: PIPES OVERLAP 35mm A T EACH JOINT . 168 mm 244mm 162m m 162m m 165 mm 244m m SL-90D 165m m 168 mm 146m m 298m m SL-06D SL-12D SL-17/24D 43 2-610mm SL-09D SL-12 /1 7D SL -2 4D SL ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 11

    11 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 VERTICAL FLUEING V FT . (M) 36' MAXIMUM (10.97M) Figure 10. USE SL D-SERIES COMPONENTS ONL Y . Figure 1 1. USE DVP-SERIES COMPONENTS ONL Y . STRAIGHT OUT HORIZONT AL FLUEING H Max. Run 24" (610mm) V ertical Flue Restrictor If the heater installation requires a vertical flu ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 12

    12 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 12. V H FT . (M ) FT . (M ) 1' MIN.(0.30M) 2' MAX.(0.61M) 2' MIN.(0.61M) 4' MAX.(1.22M) 3' MIN.(0.91M) 8' MAX.(2.44M) 4' MIN.(1.22 M) 10' MAX.(3.05M) V + H = 30' (9.14M) FLUEING WITH ONE (1) 90° ELBOW USE SL D-SERIES COMPONENTS ON ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 13

    13 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 14. V H FT . ( M) FT . (M ) 1' MIN.(0.30M) 2' MAX.(0.61M) 2' MIN.(0.61M) 4' MAX. (1.22M) 3' MIN.(0.91M) 6' MAX. (1.83M) 4' MIN.(1.22M) 8' MAX. (2.44M) 5' MIN.(1.52M) 12' MAX. (3.66M) 12' MAX.(3.66M) NOTE: V + V 1 MAX 33&a ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 14

    14 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 15. USE DVP-SERIES COMPONENTS ONL Y . FLUEING WITH TWO (2) 90° ELBOWS V H H + H 1 1´ MIN. (0.30M) 1´ MAX. (0.30M) 2´ MAX. (0.61M) 2´ MIN. (0.61M) 2´ MAX. (0.61M) 4´ MAX. (1.22M) 3´ MIN. (0.91M) 3´ MAX. (0.91M) 8´ MAX. (2.44M) 4´ MIN. (1.22M) 4´ MAX. (1.22M) 10´ M ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 15

    15 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 FLUEING WITH THREE (3) 90° ELBOWS V H H + H 1 FT . (M ) FT . (M ) FT . (M ) 2' MIN.(0.61M) 2' MAX.(0.61M) 4' MA X.(1.22M) 3' MIN.(0.91M) 3' MAX.(0.91M) 6' MAX (1.83M) 4' MIN.(1.22M) 4' MAX.( 1.2 2M) 8' MAX.(2.44M) V+V 1 = 30' MAX (9 ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 16

    16 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 17. FLUEING WITH THREE (3) 90° ELBOWS 1´ MIN. (0.30M) 1´ MAX. (0.30M) 3´ MAX. (0.91M) 2´ MIN. (0.61M) 2´ MAX. (0.61M) 5´ MAX. (1.52M) 3´ MIN. (0.91M) 4´ MAX. (1.22M) 8´ MAX. (2.44M) 4´ MIN. (1.22M) 6´ MAX. (1.83M) 10´ MAX. (3.05M) H = 6´ MAX. (1.83M) H+H 1 = 10? ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 17

    17 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 18. WARNING: F AILURE TO REMOVE INSULA TION IN THE SET OF COL- LARS YOU ARE USING COULD CAUSE A FIRE. WARNING: THE REAR FLUE COL- LAR SEAL CAP MUST REMAIN A T - T ACHED TO THE REAR FLUE COL- LARS IF THE FLUE SYSTEM IS A T - T ACHED TO THE T OP ST ARTING COLLARS. SEE FIGURE 17 ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 18

    18 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 ! W ARNING: ENSURE THA T THE HEA TER GASKET SUPPLIED WITH THE HEA TER SEALS BETWEEN THE FIRST FLUE COMPO- NENT AND THE OUTER HEA TER WRAP . Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Overlap pipe slip sections at least 38 mm. • Screws must not exceed one in ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 19

    19 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 2. Continue Adding Flue Components T o continue adding flue components in accordance with the pre-planned flue system configuration: • Ensure that each succeeding flue component is se- curely fitted and locked into the preceding compo- nent in the flue system. For elbows that are ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 20

    20 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 For V ertical Runs The flue system must be supported every eight (8) feet (2.4 M) above the heater flue outlet by wall brackets. T o install support brackets for vertical runs: • Attach wall brackets to the flue pipe and secure the wall bracket to the framing members with nails or ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 21

    21 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 ! Figure 27. Ceiling Firestop (Ceiling Side) If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole. C. Flue T ermination For Horizont a l T erminations using the DVP-TRAP T o attach and secure the termination to the last sec ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 22

    22 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 For V ertical T erminations - T o locate the flue and install the flue sections: • Locate and mark the flue centerpoint on the under- side of the roof, and drive a nail through the centerpoint. • Make the outline of the roof hole around the centerpoint nail. • The size of the ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 23

    23 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 1.4 IGNITION SYSTEM WIRING • This gas heater is equipped with an electronic igni- tion system which operates on a 6 volt system. • This appliance requires 240 V AC to be wired to the factory installed junction box. Check factory installed power cord for damage before use. Figure ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 24

    24 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 32. NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE RE- PLACED, IT MUST BE REPLACED WITH TYPE 105 • C RA TED WIRE. Figure 33. BROWN BROW N BLUE BLAC K BLUE BLACK (HO T ) BROW N (N EUTR A L) BL UE BLACK BLA CK BLUE BROW N GREEN/YELLOW BLO WER TEMPERA ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 25

    25 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 34. 1.6 FINISHING The minimum clearance to combustibles are 0 from the sides, floor , back and top (these clearances are defined by the standoffs). The minimum distance to the perpendicular side wall extending past the appliance front is 2-inches (51mm). Clearance to a mantel ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 26

    26 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 Figure 35. Figure 36. MAKE SURE THE FLAMES ARE STEADY—NOT LIFTING OR FLOA TING . Inst alling the T rim Combustible materials may be brought up to the specified clearances on the side and top front edges of the fireplace, but MUST NEVER overlap onto the front face. The joints betwe ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 27

    27 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 1 2 3 4 5 6 1.8 LOG PLACEMENT INSTRUCTIONS Log Set Assembly: LOGS-350CE-D Carefully remove the logs from the packaging. CAUTION: Logs are fragile! LOG #1 (SRV327-701): Place log #1 at the rear of the unit, with the left edge behind the tab on the pilot bracket. The right side sits b ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 28

    28 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 LOG #3 (SRV705-703): Rest log #3 against the right front grate corner and place its slot over the right burner tab. LOG #4 (SRV530-716): Place the left end of log #4 in the groove on log #2 and the right end on log #1 as shown. LOG #5 (SRV438-724): Locate the top of log #5 onto log ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 29

    29 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 LOG #6 (SRV540-704): Place log #6 against the second and third grate bars. If sooting occurs, the logs might need to be repositioned slightly to avoid excessive flame impingement. 6 6 ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 30

    30 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 ! ! OPERA TING CAUTIONS • This appliance may exhibit a slight carbon deposition. • Do not place articles on or against this appliance. • Do not use or store flammable materials near this appliance. • Do not spray aerosols in the vicinity of this appli- ance while it is in op ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 31

    31 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 2.1 SAFETY & LIGHTING INFORMA TION Follow SAFETY INFORMA TION and LIGHTING IN- STRUCTIONS to light the appliance. By design, the flame pattern will not be identical from unit to unit. Additionally , flame pattern may vary depend- ing on installation type and weather conditions. ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 32

    32 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 ! 2.2 F AN OPERA TION The accessory fan is wired in series with a speed con- trol switch and a temperature sensor switch. Set the speed control to an "ON" position and light the heater . The temperature sensor switch will automatically start the fan when the switch warms u ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 33

    33 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 PILOT B RACK ET RET AINI N G SC REWS 3.1 REMOV AL OF COVERS FOR SERVICING A . Control Compartment Door • Rotate the lower door down to access the gas controls. B . Dress Guard and Glass Door • Lift the front dress guard up and out away from the appliance side surrounds. Replace ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 34

    34 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 3.5 TROUBLESHOOTING SL-350TRSI-AUE With proper installation and maintenance, your new Gas Heater should provide years of trouble-free service. If you do experienc e a problem, refer to the T rouble Shooting Guide below . This guide will assist a qualified service person in the diagn ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 35

    35 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 (NG , LP) Exploded Parts Diagram Service Parts SL-350TRSI-AUE Beginning Manufacturing Date: 6/06 Ending Manufacturing Date: ______ 22 Log set assembly 2 13 4 10 16 15 14 12 7 8 11 21 32 31 23 25 27 24 26 28 18 4.0 REPLACEMENT P ARTS 1 5 19 6 17 33 20 9 3 30 29 34 35 Í ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 36

    36 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 SL-350TRSI-AUE Service Parts List IMPORT ANT : When ordering, supply serial and model numbers to ensure correct service parts. IT EM PAR T S PAR T N U M B E R 1 Va lve NG 2098- 134 Va lve L P 2098- 135 2 O rif i ce N G 582- 844 O rif i ce LP 582- 055 3 18 I in Fl ex T u be Asse m bl ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 37

    37 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 LIMITED 10 YEAR WARRANTY HEAT & GLO, a brand of Hearth & Home Technologies Inc. In order to presumptively establish the dates to which your HEAT & GLO Limited 10 Year Warranty runs, you must mail the completed warranty card to HEAT & GLO, a brand of Hearth & Home ...

  • Hearth and Home Technologies SL-350TRSI-AUE - page 38

    38 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev . B • 6/06 For Service or Replacement Part s Contact: Melbourne Jetmaster 444 Swan S treet Richmond 3121 (03) 9429-5573 Perth Fireplace Corner 277 Lord S treet East Perth 6000 (08) 9228-2600 Sydney Jetmaster 10 Martin Avenue Arncliff 2205 (02) 9597-7222 ...

Manufacturer Hearth and Home Technologies Category Electric Heater

Documents that we receive from a manufacturer of a Hearth and Home Technologies SL-350TRSI-AUE can be divided into several groups. They are, among others:
- Hearth and Home Technologies technical drawings
- SL-350TRSI-AUE manuals
- Hearth and Home Technologies product data sheets
- information booklets
- or energy labels Hearth and Home Technologies SL-350TRSI-AUE
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hearth and Home Technologies SL-350TRSI-AUE.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hearth and Home Technologies SL-350TRSI-AUE, service manual, brief instructions and user manuals Hearth and Home Technologies SL-350TRSI-AUE. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hearth and Home Technologies SL-350TRSI-AUE.

Similar manuals

A complete manual for the device Hearth and Home Technologies SL-350TRSI-AUE, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hearth and Home Technologies SL-350TRSI-AUE by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hearth and Home Technologies SL-350TRSI-AUE.

A complete Hearth and Home Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hearth and Home Technologies SL-350TRSI-AUE - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hearth and Home Technologies SL-350TRSI-AUE, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hearth and Home Technologies SL-350TRSI-AUE, that we can find in the current document
3. Tips how to use the basic functions of the device Hearth and Home Technologies SL-350TRSI-AUE - which should help us in our first steps of using Hearth and Home Technologies SL-350TRSI-AUE
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hearth and Home Technologies SL-350TRSI-AUE
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hearth and Home Technologies SL-350TRSI-AUE in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hearth and Home Technologies SL-350TRSI-AUE?

Use the form below

If you did not solve your problem by using a manual Hearth and Home Technologies SL-350TRSI-AUE, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies SL-350TRSI-AUE it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)