English dropdown-ico

Manual Poulan 183284

48 pages 1.99 mb
Download

Go to site of 48

Summary
  • Poulan 183284 - page 1

    OWNER'S MANUAL MODEL: PR20PH42STC LAWN TRACTOR Always Wear Eye Protection During Operation WARNING: Read this Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. IMPOR T ANT MANU AL Do Not Throw A wa y 183284 Rev. 1 09.20.02 RD/MH Printed in U.S.A. ...

  • Poulan 183284 - page 2

    2 Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. SAFETY RULES I . GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machin ...

  • Poulan 183284 - page 3

    3 Safe Operation Practices for Ride-On Mowers SAFETY RULES • Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. • Never carry ...

  • Poulan 183284 - page 4

    4 PRODUCT SPECIFICA TIONS GASOLINE CAPACITY 3.5 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) OIL CAPACITY: W/ FILTER: 4.0 PINTS W/O FILTER: 3.75 PINTS SPARK PLUG: CHAMPION RC12YC (GAP: .040") GROUND SPEED (MPH): FORWARD: 0 – 5.5 REVERSE: 0 – 2.4 TIRE PRESSURE: FRONT: 14 P SI REAR: 10 ...

  • Poulan 183284 - page 5

    5 UNASSEMBLED P AR TS Steering Wheel (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat Steering Wheel Inser t Steering Wheel Adapter Steering Sleeve Steering Sleeve Extension (2) Keys Slope Sheet Keys (2) Mulch Blades ...

  • Poulan 183284 - page 6

    6 Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. T OOLS REQUIRED FOR ASSEMBL Y A socket wrench se ...

  • Poulan 183284 - page 7

    7 ASSEMBL Y FIG. 3 SEAT PAN SHOULDER BOLT ADJUSTMENT KNOB FLAT WASHER SEAT NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid. INSTALL SEAT (See Fig. 3) Adjust seat before tightening adjustment knob. • Remove adjustment knob and flat washer securing seat to cardb ...

  • Poulan 183284 - page 8

    8 FIG. 5 ASSEMBL Y DEFLECTOR SHIELD LATCH HOOKS MULCHER PLATE IMPORTANT: FOR SHIPPING PURPOSES, THE MULCHER PLATE WAS PREATTACHED TO YOUR MOWER. THE MULCHER PLATE MUST ONLY BE USED WITH THE MULCHING BLADES THAT CAME PACKED SEPARATELY IN THE CARTON. YOUR MOWER CAME FACTORY EQUIPPED WITH HIGH PERFORMANCE BLADES, WHICH ARE THE BEST BLADES FOR BAGGING ...

  • Poulan 183284 - page 9

    9 CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in “PRODUCT SPECIFICATIONS” section of this manual. CHECK MOWER LEVELNESS For best cutting results, mower should be properly leveled. See ? ...

  • Poulan 183284 - page 10

    10 These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) OVER TEMP LIGHT KEEP AREA CLEAR SLOPE HAZARDS 15 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF OIL PRESSURE LIGHTS O ...

  • Poulan 183284 - page 11

    11 AMPS 60 0 60 OPERA TION KNO W Y OUR TRA CT OR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. FIG. 6 Our tractors conform to the safety standards of the Am ...

  • Poulan 183284 - page 12

    12 OPERA TION CAUTION: Always stop tractor com- pletely, as described above, before leav- ing the operator's position; to empty grass catcher, etc. TO USE THROTTLE CONTROL (See Fig. 7) Always operate engine at full throttle. • Operating engine at less than full throttle reduces the battery charging rate. • Full throttle offers the best bag ...

  • Poulan 183284 - page 13

    13 OPERA TION LOW POSITION TO OPERATE MOWER (See Fig. 9) Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. • Select desired height of cut. • Lower mower with attachment lift control. • Start mower ...

  • Poulan 183284 - page 14

    14 OPERA TION TO START ENGINE (See Fig. 6) When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Be sure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress brake pedal and set parking brak ...

  • Poulan 183284 - page 15

    15 OPERA TION FIG. 11 PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is running. To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have devel- ...

  • Poulan 183284 - page 16

    16 B E F O R E E A C H U S E T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Battery Level Check Tire Pressure Clean Battery and Terminals FILL IN DATES AS YOU COMPLETE REGULAR SERVICE MAINTENANCE SCH ...

  • Poulan 183284 - page 17

    17 CUST OMER RESPONSIBILITIES TRA CT OR Always observe safety rules when performing any mainte- nance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjust- ments section of this manual). TIRES • Maintain proper ...

  • Poulan 183284 - page 18

    18 CUST OMER RESPONSIBILITIES FIG. 15 CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt ...

  • Poulan 183284 - page 19

    19 CUST OMER RESPONSIBILITIES MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPEC ...

  • Poulan 183284 - page 20

    20 SER VICE AND ADJUSTMENTS TRA CT OR FIG. 18 RETAINER SPRINGS (BOTH SIDES) RETAINER SPRINGS (BOTH SIDES) ELECTRIC CLUTCH PULLEY FRONT LINK SUSPENSION ARMS RETAINER SPRING ANTI-SWAY BAR TO REMOVE MOWER (See Fig. 18) Mower will be easier to remove from the right side of tractor. • Place attachment clutch switch in “DISENGAGED” position. • Mo ...

  • Poulan 183284 - page 21

    21 SER VICE AND ADJUSTMENTS FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22) IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE. To obtain the best cutting results, the mower housing should be adjusted so that the front i ...

  • Poulan 183284 - page 22

    22 FIG. 25 SER VICE AND ADJUSTMENTS FIG. 24 TO ADJUST BRAKE (See Fig. 24) Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle. If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted. • Depres ...

  • Poulan 183284 - page 23

    23 TO REMOVE WHEEL FOR REPAIRS (See Fig. 26) • Block up axle securely. • Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle. Insert square key. • Replace washers and snap retaini ...

  • Poulan 183284 - page 24

    24 FIG. 30 SWIVEL CLAMP SCREW STOP ENGINE TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30) The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows: • With engine not running, move throttle control lever to f ...

  • Poulan 183284 - page 25

    25 SER VICE AND ADJUSTMENTS TO ADJUST CARBURETOR Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment. High speed stop is factory adjusted. Do not adjust - damage may result. IMPORTANT: NEVER TAMPER WITH THE EN ...

  • Poulan 183284 - page 26

    26 ST ORA GE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. TRA CT OR Remove mower from tr ...

  • Poulan 183284 - page 27

    27 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air filter. 5. Clean/replace air filter. 6. Dirty fuel filter. ...

  • Poulan 183284 - page 28

    28 TR OUBLESHOO TING POINTS Engine continues to run 1 . Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves corrected, contact an authorized service center/ seat with attachment department. clutch engaged Poor cut - uneven 1. Worn, bent or loose blade. 1 . Replace blade. Tighten bla ...

  • Poulan 183284 - page 29

    29 BATTERY FUSE RED RED RED RED BLACK BLACK BLACK BLACK BLACK BLACK BLACK IGNITION UNIT SPARK PLUGS GAP (2 PLUGS ON TWIN CYL. ENGINES) NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS BLACK ORANGE BROWN M SOLENOID WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOU ...

  • Poulan 183284 - page 30

    30 REP AIR P ARTS TRA CT OR - MODEL NUMBER PR20PH42STC, PRODUCT NO . 954 56 78-33 ELECTRICAL 28 29 26 24 42 43 25 41 27 27 40 33 30 50 22 21 81 D.C. AMPERES 45 12 12 11 10 8 2 1 27 55 52 16 ...

  • Poulan 183284 - page 31

    31 KEY P ART N O . NO . DESCRIPTION 1 144927 Battery 2 74760412 Bolt Hex Hd 1/4-20 UNC X 3/4 8 7603J Tray, Battery 1 0 145211 Bolt, BTR FRT 1/4-20 x 7.5 1 1 150109 Hold Down Battery, Front 1 2 145769 Nut, Push, Nylon 1 6 176138 Switch Interlock Push-In 2 1 175688 Harness Asm Light W/4152j 2 2 4152J Bu l b Li g h t 24 8860R Cable Battery 2 5 146148 ...

  • Poulan 183284 - page 32

    32 REP AIR P ARTS TRA CT OR - MODEL NUMBER PR20PH42STC, PRODUCT NO . 954 56 78-33 CHASSIS AND ENCLOSURES 64 209 158 74 30 159 209 13 3 31 1 9 157 156 10 26 144 26 10 3 3 3 142 3 3 3 142 143 60 17 29 145 161 166 37 37 209 11 209 209 20 59 28 166 166 154 209 166 155 166 209 54 58 54 14 14 38 38 213 214 3 2 206 ...

  • Poulan 183284 - page 33

    33 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 174619 Chassis 2 176554 Drawbar 3 17060612 Screw 3/8-16x3/4 9 163976X428 Dash 1 0 72140608 B olt 3/8-16 x 1 1 1 167203 Panel Dash Lh 1 3 178298 Panel Dash Rh 1 4 17490608 Screw Thdrol 3/8-16 x 1/2 1 7 175260X428 Hood 2 0 162026 Plate Battery 2 5 19131312 Washer 13/32 X 13/16 ...

  • Poulan 183284 - page 34

    34 REP AIR P ARTS TRA CT OR - MODEL NUMBER PR20PH42STC, PRODUCT NO . 954 56 78-33 DRIVE 29 28 30 52 32 37 53 35 55 36 62 35 36 22 34 16 1 77 77 241 32 30 52 57 25 19 24 26 26 76 78 75 74 27 26 59 19 219 221 221 220 222 221 19 51 51 250 19 19 6 231 239 33 239 238 52 237 233 240 232 241 235 242 221 215 224 225 223 223 223 223 226 226 234 236 227 218 ...

  • Poulan 183284 - page 35

    35 KEY P AR T N O . NO . DESCRIPTION KEY P AR T N O . NO . DESCRIPTION NOTE: All component dimensions give in U.S. inches. 1 inch = 25.4 mm REP AIR P ARTS TRA CT OR - MODEL NUMBER PR20PH42STC, PRODUCT NO . 954 56 78-33 DRIVE 1 - - - - - - Transaxle (Order parts from transaxle manufacturer) Hydro gear Model 323-0510 6 17060512 Screw 5/16-18 x 3/4 9 ...

  • Poulan 183284 - page 36

    36 REP AIR P AR TS TRA CT OR - MODEL NUMBER PR20PH42STC, PRODUCT NO . 954 56 78-33 STEERING ASSEMBLY 5 5 4 3 43 6 43 8 10 40 32 11 8 6 87 46 46 8 6 87 29 88 71 17 43 91 2 33 35 34 68 67 67 67 13 65 68 15 15 15 29 29 82 38 12 72 1 41 42 37 36 37 ...

  • Poulan 183284 - page 37

    37 KEY P AR T N O . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm. REP AIR P ARTS TRA CT OR - MODEL NUMBER PR20PH42STC, PRODUCT NO . 954 56 78-33 STEERING ASSEMBLY 1 180656 W heel Steering 2 172393 Axle Cast Lt Machined 3 169840 S pindle Asm LH 4 169839 Spindle Asm RH 5 6266H Bearing Race Thrust Harden 6 121 ...

  • Poulan 183284 - page 38

    38 REP AIR P ARTS TRA CT OR - MODEL NUMBER PR20PH42STC, PRODUCT NO . 954 56 78-33 ENGINE 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 10 62 6 5 72 13 26 25 4 8 32 31 34 33 37 33 39 17 16 17 3 81 23 45 14 38 15 KEY P ART N O . NO . DESCRIPTION 1 175437X428 C ontrol Throttle 2 164863 Screw Hwhd Hi-Lo #13-16 x 3/4 3 - - - - - - - - Engine, Briggs Model 40 ...

  • Poulan 183284 - page 39

    39 KEY P AR T N O . NO . DESCRIPTION KEY P AR T N O . NO . DESCRIPTION 1 171684 Seat 2 140551 Bracket Pivot Seat 8 720 3 71110616 Bolt Fin Hex 3/8-16 Unc x 1 4 19131610 W asher Flat 13/32 x 1 x 10 Ga. 5 145006 C lip Push-In 6 73800600 N u t H e x w /Ins. 3/8-16 Unc 7 124181X Spring Seat Cprsn 2 250 Blk Zi 8 17000616 S crew 3/8-16 x 1 9 19131614 W a ...

  • Poulan 183284 - page 40

    40 10 3 16 9 KE Y PART NO. N O. DESCRIPTION KEY P AR T N O . NO . DESCRIPTION 1 59192 C a p Valve Tire 2 65139 S t e m V a l v e 3 170455 T i r e F T 1 5 X 6 0 - 6 S e r v i c e 4 59904 Tube Front (Service Item Only) 5 106732X421 R i m A s m 6"front Service 6 278H F i t t i n g Grease (Front Wheel Only) 7 9040H Bearing Flange (Front Wheel Only ...

  • Poulan 183284 - page 41

    41 REP AIR P ARTS TRA CT OR - MODEL NUMBER PR20PH42STC, PRODUCT NO . 954 56 78-33 MO WER LIFT 36 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 8 23 24 25 27 28 29 30 50 26 37 41 40 38 12 11 31 32 31 32 19 19 13 13 13 13 49 1 159461 Wire Asm Inner/Sprg W/plunger 2 159476 Shaft Asm Lift RH w/Inf 3 138284 P i n G roove 4 12000002 E R i n g #5133-62 5 ...

  • Poulan 183284 - page 42

    42 REP AIR P ARTS TRA CT OR - MODEL NUMBER PR20PH42STC, PRODUCT NO . 954 56 78-33 MO WER DECK 15 14 13 11 10 9 8 16 68 37 30 31 32 33 146 148 145 150 45 144 54 55 56 34 1 46 44 21 24 25 26 27 2 28 29 23 21 21 21 18 18 20 2 59 19 4 5 6 21 40 143 36 40 37 40 159 61 149 118 136 21 139 137 119 117 116 5 21 134 21 5 134 135 136 116 113 117 119 118 137 1 ...

  • Poulan 183284 - page 43

    43 KEY P AR T N O . NO . DESCRIPTION KEY P AR T N O . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 182032X421 M ower Deck Assembly, 42" 2 72140506 B o l t 3 138017 Bracket Asm Fr. Sway Bar 3/42 4 165460 B r acket Asm Deck 42" Sway Bar 5 4939M R e t a in e r S pr i n g 6 178024 Bar Sway Deck 8 850 ...

  • Poulan 183284 - page 44

    44 SER VICE NO TES ...

  • Poulan 183284 - page 45

    45 SER VICE NO TES ...

  • Poulan 183284 - page 46

    46 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacin ...

  • Poulan 183284 - page 47

    47 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven ...

  • Poulan 183284 - page 48

    Your POULAN PRO product has been expertly engineered and carefully manufactured to rigid quality standards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SER VICE OR REPLA CEMENT P AR TS: 1. Consult your dealer/place of purchase. 2. Consult the yellow pages of your phone dir ...

Manufacturer Poulan Category Lawn Mower

Documents that we receive from a manufacturer of a Poulan 183284 can be divided into several groups. They are, among others:
- Poulan technical drawings
- 183284 manuals
- Poulan product data sheets
- information booklets
- or energy labels Poulan 183284
All of them are important, but the most important information from the point of view of use of the device are in the user manual Poulan 183284.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Poulan 183284, service manual, brief instructions and user manuals Poulan 183284. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Poulan 183284.

Similar manuals

A complete manual for the device Poulan 183284, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Poulan 183284 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Poulan 183284.

A complete Poulan manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Poulan 183284 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Poulan 183284, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Poulan 183284, that we can find in the current document
3. Tips how to use the basic functions of the device Poulan 183284 - which should help us in our first steps of using Poulan 183284
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Poulan 183284
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Poulan 183284 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Poulan 183284?

Use the form below

If you did not solve your problem by using a manual Poulan 183284, ask a question using the form below. If a user had a similar problem with Poulan 183284 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)