Manual Knoll Systems PRM200

6 pages 0.15 mb
Download

Go to site of 6

Summary
  • Knoll Systems PRM200 - page 1

    PRM150, PRM200 Advanced Power Conditioners Installation Instructions v1.1 Warning : To be installed and/or used in accordance with appropriate electrical codes and regulations Introduction: Thank you for your purchase of a Knöll PRM150 or PRM200 Advanced Power Conditioner and congratulations on your choice. This specially made conditioner is desig ...

  • Knoll Systems PRM200 - page 2

    Coaxial surge suppression is often over looked. A convenient “F” connector is provided both for cable TV and the satellite dish. This allows full surge protection through a low loss pass through connection. Telephone line surge protection is provided to bring an added measure of safety to your home. An RJ connector is provided for both in and o ...

  • Knoll Systems PRM200 - page 3

    Installation: The PRM200 power source connection must be adequate for use at 20 amps. We recommend a properly grounded 30-amp circuit, wired with 10-gauge wiring, if continuous operation near 20 amps is anticipated. A dedicated (nothing else connected) 20-amp circuit is the minimum acceptable to comply with NEC requirements. Consult a qualifi ed el ...

  • Knoll Systems PRM200 - page 4

    Delayed Turn On’s . When the power conditioner is turned on, th e two outlets labelled “Delay Min” turn on immediately (along with the unswitch ed outlets already turned on). About two seconds later the next tw o outlets labelled “Delay Med” turn on. About two seconds later (four seconds from wh en the power conditioner was first turned o ...

  • Knoll Systems PRM200 - page 5

    Fuses There is a single slow blow 15-amp fuse in the PRM150 and there is a single 20 amp slow blow fuse in the PRM200. As per safety regulations, only authorized and experienced service people, including Knoll factory personnel are authorized to change these fuses. DO NOT CHANGE these fuses for safety reasons. Cable TV and Satellite Dish For best p ...

  • Knoll Systems PRM200 - page 6

    PRM150 and PRM200 SPECIFICATIONS Current rating: PRM150 15 amps (1800 watts at 60/120 VAC, 60 HZ) fuse protected. PRM200 20 amps (2400 watts at 60/120 VAC, 60 HZ) fuse protected. Voltage Ranges: 90-135 VAC 60 Hz Remote trigger voltage: 3-24 VDC (input impedance 1k ohm) Clamping Voltage 250v peak (175 volts RMS) Response time: 1 nanosecond Max Surge ...

Manufacturer Knoll Systems Category Power Supply

Documents that we receive from a manufacturer of a Knoll Systems PRM200 can be divided into several groups. They are, among others:
- Knoll Systems technical drawings
- PRM200 manuals
- Knoll Systems product data sheets
- information booklets
- or energy labels Knoll Systems PRM200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Knoll Systems PRM200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Knoll Systems PRM200, service manual, brief instructions and user manuals Knoll Systems PRM200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Knoll Systems PRM200.

A complete manual for the device Knoll Systems PRM200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Knoll Systems PRM200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Knoll Systems PRM200.

A complete Knoll Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Knoll Systems PRM200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Knoll Systems PRM200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Knoll Systems PRM200, that we can find in the current document
3. Tips how to use the basic functions of the device Knoll Systems PRM200 - which should help us in our first steps of using Knoll Systems PRM200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Knoll Systems PRM200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Knoll Systems PRM200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Knoll Systems PRM200?

Use the form below

If you did not solve your problem by using a manual Knoll Systems PRM200, ask a question using the form below. If a user had a similar problem with Knoll Systems PRM200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)