Manual Hearth and Home Technologies CD4236MR

76 pages 8.38 mb
Download

Go to site of 76

Summary
  • Hearth and Home Technologies CD4236MR - page 1

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 1 Model(s): CD4236MR CD4842MR CD4236MLR CD4842MLR CD4236MIR CD4842MIR CD4236MILR CD4842MILR Direct V ent Gas Appliance Owner ’ s Manual Installation and Operation Installation and service of this appliance should be performed by quali fi ed personnel. Hearth & Home ...

  • Hearth and Home Technologies CD4236MR - page 2

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fi replace: _____________________ Dealership purchased from: __ ...

  • Hearth and Home Technologies CD4236MR - page 3

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous ...

  • Hearth and Home Technologies CD4236MR - page 4

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 4 Î = Contains updated information. 14 Appliance Setup A. Remove Clean Face Components 54 B. Remove Glass Assembly 54 C. Remove the Shipping Materials 54 D. Clean the Appliance 54 E. Accessories 54 F . Install the Refractory 54 G. Place the Lava Rock 54 H. Place the V er ...

  • Hearth and Home Technologies CD4236MR - page 5

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 5 B. Limited Lifetime W arranty Gas Appliance (Fir eplace) Limited Lifetime W arranty HEARTH & HOME TECHNOLOGIES INC. (“HHT”) extends the following warranty for HEA TILA TOR ® gas appliances installed in the United States of America or Canada (the "Appliance ...

  • Hearth and Home Technologies CD4236MR - page 6

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 6 B. T empered Glass Speci fi cations Hearth & Home T echnologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as de fi ned by the Consumer Product Safety Commission (CPSC). The tempered glass has bee ...

  • Hearth and Home Technologies CD4236MR - page 7

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 7 G. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth a ...

  • Hearth and Home Technologies CD4236MR - page 8

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 8 Decorative Doors (not shown) Section 2.E. Fixed Glass Assembly (not shown) Section 2.F . Grate (not shown) Section 3.B. Mantel Hearth (not required) Clear Space Section 2.D. Fan Kits Section 2.C Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT oper ...

  • Hearth and Home Technologies CD4236MR - page 9

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 9 Clear space 3 ft (914 mm) in front of appliance D. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel ...

  • Hearth and Home Technologies CD4236MR - page 10

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 10 I. Lighting Instructions (IPI) • For normal use, activate/deactivate your fi replace with the wall switch or remote control. • The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer . T o prolong battery life, remove ...

  • Hearth and Home Technologies CD4236MR - page 11

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 1 1 J. Lighting Instructions (Standing Pilot) • For normal use, activate/deactivate your fi replace with the wall switch or remote control. • If your fi replace must be deactivated for service or an extended period of time, follow the instructions below . A. This ap ...

  • Hearth and Home Technologies CD4236MR - page 12

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 12 Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the fi replace off and allow it to completely cool. • Remove fi xed glass assembly . See Section 14.K. • Clean fi xed glass assembly . See Section 3.A. ...

  • Hearth and Home Technologies CD4236MR - page 13

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 13 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care. Glass is breakable. • Avoid striking, scratching or slamming glass • Avoid ...

  • Hearth and Home Technologies CD4236MR - page 14

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 14 Burner Ignition and Operation Frequency: Annually By: Quali fi ed Service T echnician T ools needed : Protective gloves, vacuum cleaner , whisk broom, fl ashlight, voltmeter , indexed drill bit set, and a manometer . • V erify burner is properly secured and aligned ...

  • Hearth and Home Technologies CD4236MR - page 15

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 15 Noncombustible roof flashing maintains minimum clearance around pipe (SECTION 10) Ceiling Firestop on floor of attic (SECTION 8) V ent Pipe (SECTIONS 7, 8, 10) Framing/Header (SECTION 5) Gas Line (SECTION 1 1) Framing Headed off in Ceiling Joists (SECTION 8) Mantel &am ...

  • Hearth and Home Technologies CD4236MR - page 16

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 16 B. Design and Installation Considerations Heatilator direct vent gas appliances are designed to op- erate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. Installa ...

  • Hearth and Home Technologies CD4236MR - page 17

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 17 5 5 F raming and Clearances A. Select Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). W ARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for s ...

  • Hearth and Home Technologies CD4236MR - page 18

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 18 Combustible flooring may be installed next to the front of the appliance. C B A 1/2 in. (13 mm) 1/2 in. (13 mm) Drywall 0 in. 30 in. (762 mm) to ceiling D 0 in. to floor 0 in. to level of standoffs Combustible Object 36 in. (914 mm) B. Construct the Appliance Chase A c ...

  • Hearth and Home Technologies CD4236MR - page 19

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 19 Measured from top of hood (in inches) 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 5 5-1/2 6-1/4 7 7-3/4 8-1/2 9-1/4 10 10-3/4 11 - 1 / 2 12-1/4 13 13-3/4 14-1/2 15-1/4 16 30 in. minimum to ceiling D. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all min ...

  • Hearth and Home Technologies CD4236MR - page 20

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 20 Horizontal overhang 12 X 20 in. (508 mm) Lowest Discharge Opening T ermination Cap Roof Pitch is X / 12 V ertical wall H (min.) - Minimum height from roof to lowest discharge opening. 24 in. min. (610 mm) Roof Pitch H (Min.) Ft. Roof Pitch H (Min.) Ft. Flat to 6/12 1.0 ...

  • Hearth and Home Technologies CD4236MR - page 21

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 21 Dimension Descriptions A Clearance above the ground, a veranda, porch, deck or balcony - 12 in. (30 cm) minimum. * B Clearance to window or door that may be opened – 10,000 BTUs or less, 6 in. (15 cm) minimum; 10,000-50,000 BTUs, 9 in. (23 cm) minimum; over 50,000 BT ...

  • Hearth and Home Technologies CD4236MR - page 22

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 22 Horizontal V ertical 8-1/2 in. 8-1/2 in. 12 in. On 45° runs, 1 ft (.3 m) of diagonal is equal to 8-1/2 in. (216 mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A. Approved Pipe This appliance is approved for use with Hearth & Home T echnologies DVP and/or ...

  • Hearth and Home Technologies CD4236MR - page 23

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 23 H 1 V 1 T o replace the fi rst starter elbow with two 45° elbows, refer to Figure 7.4. All other 90° elbows can be replaced with two 45° elbows. General Rules: • SUBTRACT 3 ft. from the total H measurement for each 90° elbow installed horizontally . • SUBTRACT ...

  • Hearth and Home Technologies CD4236MR - page 24

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 24 4 ft min. (1.22 m) 25 ft max. (7.62 m) H 1 V 1 H 2 H 3 Installed Horizontally Installed V ertically H 2 Figure 7.5 T wo Elbows 1. T op V ent - Horizontal T ermination - (continued) Figure 7.4 T wo 45° Elbows replacing One 90° Elbow V 1 min. V 1 max. H 1 +H 2 max. H 1 ...

  • Hearth and Home Technologies CD4236MR - page 25

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 25 Figure 7.6 1. T op V ent - Horizontal T ermination - (continued) Three Elbows H 1 V 1 V 2 H 2 Installed V ertically V 1 min. V 1 + V 2 max. H 1 +H 2 max. ft m ft m ft m DVP 1 0.30 24 7.32 19 5.79 SLP 1 0.30 22 6.71 19 5.79 ...

  • Hearth and Home Technologies CD4236MR - page 26

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 26 2. T op V ent - V ertical T ermination No Elbow Figure 7.7 Figure 7.8 T wo Elbows Note: If installing a vertical vent/ termination off the top of the appli- ance, the vertical termination baf fl e should be used. 12 ft (3.66 m) min. 60 ft (18.29 m) max. 12 ft (3.66 m) ...

  • Hearth and Home Technologies CD4236MR - page 27

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 27 Figure 7.9 2. T op V ent - V ertical T ermination - (continued) Three Elbows 12 ft (3.66 m) min. 60 ft (18.29 m) max. Maximum horizontal run is 100% of vertical, but cannot exceed 26 ft (7.92 m) Note: If installing a vertical vent/ termination off the top of the appli- ...

  • Hearth and Home Technologies CD4236MR - page 28

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 28 3. Rear V ent - Horizontal T ermination Figure 7.10 Figure 7.1 1 No Elbow One 45° Elbow 18 in. (457 mm) max. 18 in. (457 mm) max. ...

  • Hearth and Home Technologies CD4236MR - page 29

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 29 3. Rear V ent - Horizontal T ermination - (continued) T wo Elbows Figure 7.12 Figure 7.13 Three Elbows H 2 V 1 H 1 H 2 V 1 H 3 H 1 Installed Horizontally H 1 max. V 1 min. H 1 +H 2 max. ft m ft m ft m 2 0.61 1 0.30 3 0.91 4 1.22 2 0.61 6 1.83 6 1.83 3 0.91 9 2.74 8 2.4 ...

  • Hearth and Home Technologies CD4236MR - page 30

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 30 4. Rear V ent - V ertical T ermination One Elbow Figure 7.14 T wo Elbows Figure 7.15 12 ft (3.66 m) min. 60 ft (18.29 m) max. 0 min. 6 ft (1.83 m) max. 12 ft (3.66 m) min. 60 ft (18.29 m) max. 0 min. 6 ft (1.83 m) max. Maximum horizontal run is 100% of vertical, but ca ...

  • Hearth and Home Technologies CD4236MR - page 31

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 31 4. Rear V ent - V ertical T ermination - (continued) Three Elbows Figure 7.16 12 ft (3.66 m) min. 60 ft (18.29 m) max. 0 min. 6 ft (1.83 m) max. Maximum horizontal run is 100% of vertical, but can- not exceed 26 ft (7.92 m). ...

  • Hearth and Home Technologies CD4236MR - page 32

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 32 F . Install V ertical T ermination Baf fl e • Remove the glass (refer to Section 14.K.) to access the fi rebox and 5 in. inner fl ue. • Fold the baf fl e (Figure 7.17) to an approximate 90° angle (see Figure 7.18). • Squeeze the open end of the bent baf fl ...

  • Hearth and Home Technologies CD4236MR - page 33

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 33 * When using SLP pipe, minimum clearances from the vent pipe to combustible materi- als at inside wall firestops are: T op: 2-1/2 in. (64 mm) Bottom: 1/2 in. (13 mm) Sides: 1 in. (25 mm) Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). • DVP heat sh ...

  • Hearth and Home Technologies CD4236MR - page 34

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 34 3 fasteners per side Ceiling firestop installed below ceiling. Ceiling firestop installed above ceiling. Install attic insula- tion shields before or after installation of vent system. A TTIC ABOVE A PIPE DVP SLP A 10 in. (254 mm) 9 in. (229 mm) A C. Install the Ceilin ...

  • Hearth and Home Technologies CD4236MR - page 35

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 35 Bend all tabs inward 90° to maintain clearance and prevent insulation from falling inside Insert 3 screws Bend 4 tabs inward 90° to maintain clearance Laser-etched cut lines D. Install Attic Insulation Shield W ARNING! Fire Risk. DO NOT allow loose materials or insul ...

  • Hearth and Home Technologies CD4236MR - page 36

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 36 CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installa- tion. Sheet metal edges are sharp. NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time. A. Convert from T op V ent t ...

  • Hearth and Home Technologies CD4236MR - page 37

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 37 • Remove four screws holding outer collar to appliance top. See Figure 9.5. Remove outer collar . Figure 9.5 Outer Collar , Remove Four Screws • Remove four screws holding inner collar to appliance top. See Figure 9.6. Remove inner collar . Figure 9.6 Remove Four I ...

  • Hearth and Home Technologies CD4236MR - page 38

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 38 Figure 9.1 1 Place Outer Collar on Rear of Appliance • Place outer collar on rear of appliance and replace four screws to hold collar in place. See Figure 9.1 1. Make sure insulation is attached to the collar base! Figure 9.12 Cover Plate Placed on Rear of Appliance ...

  • Hearth and Home Technologies CD4236MR - page 39

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 39 Figure 9.16 Cover Plate-Replace Figure 9.17 Place Cover Plate on T op of Appliance • Locate heat shield cover plate removed in the fi rst step. Place the heat shield cover plate on top of heat shield. Replace four screws to hold this plate in place. See Figure 9.16. ...

  • Hearth and Home Technologies CD4236MR - page 40

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 40 Nailing Flanges (both sides) B. Secure and Level the Appliance W ARNING! Risk of Fire! Prevent contact with: • Sagging or loose insulation • Insulation backing or plastic • Framing and other combustible materials Block openings into the chase to prevent entry of ...

  • Hearth and Home Technologies CD4236MR - page 41

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 41 Lances 1 0 10 Install V ent P ipe A. Assemble Pipe Sections (DVP Only) Attach Pipe to the Firebox Assembly Note: The end of the pipe sec tions with the lanc ed tabs will face towards the applianc e. Attach the fi rst pipe section to the starting collar: • Lanced pip ...

  • Hearth and Home Technologies CD4236MR - page 42

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 42 B. Assemble V ent Sections (SLP Only) T o attach the fi rst vent component to the starting collars of the appliance • Attach an SLP-DVP24 adapter to the starting collar of the appliance. • Lock the vent components into place by sliding the pipe section onto the co ...

  • Hearth and Home Technologies CD4236MR - page 43

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 43 Figure 10.8 Securing V ertical Pipe Sections Figure 10.9 Securing Horizontal Pipe Sections D. Secure the V ent Sections • V ertical runs of DVP pipe must be supported every 8 ft. (2.44 m) after the 25 ft. (7.62 m) maximum unsupported rise. • V ertical runs of SLP p ...

  • Hearth and Home Technologies CD4236MR - page 44

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 44 Cut hole 1/8 in. (3 mm) greater in size than pattern of support box as it is projected onto roofline. 2 in. (51 mm) minimum below finished ceiling Cathedral ceiling support box Level F . Install Decorative Ceiling Components (SLP only) A decorative ceiling thimble can ...

  • Hearth and Home Technologies CD4236MR - page 45

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 45 G. Install Metal Roof Flashing Note: Skip to Section 10 .I. if using the RF4 - 8. • See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof. • Slide the roof fl ashing over the pipe sections exte ...

  • Hearth and Home Technologies CD4236MR - page 46

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 46 I. Install RF4-8 The RF4-8 may be used in place of the roof fl ashing and storm collar (Sections 10.G. and 10.H.) Pipe must be supported within 12 in. (305 mm) of the roo fl ine using plumbers strapping or an SLP-FS when us- ing the RF4-8 Flashing. Refer to Sect. 8.C ...

  • Hearth and Home Technologies CD4236MR - page 47

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 47 J. Install V ertical T ermination Cap • Attach the vertical termination cap by sliding the inner collar of the cap into the inner fl ue of the pipe section while placing the outer collar of the cap over the outer fl ue of the pipe section. • Secure the cap by dri ...

  • Hearth and Home Technologies CD4236MR - page 48

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 48 INTERIOR Heat Shield or Extended Heat Shield W all Shield Firestop Heat Shield 1-1/2 in. (38 mm) min. overlap SHEA THING V ent depth from back of appliance to outside surface of exterior wall (see chart below) Slip Section can be extended Inner V ent Outer V ent EXTERI ...

  • Hearth and Home Technologies CD4236MR - page 49

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 49 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home T echnologies speci fi ed and approved parts. B. Gas Pressure • Optimum appliance performanc ...

  • Hearth and Home Technologies CD4236MR - page 50

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 50 Ignitor Button Figure 12.1 Ignitor Button B. Standing Pilot Ignition System Wiring • The standing pilot ignition system wiring does not require a 1 10 V AC supply to operate. • A 1 10 V AC junction box MUST be installed for use with a fan or remote control. See Fig ...

  • Hearth and Home Technologies CD4236MR - page 51

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 51 E. Electrical Service and Repair W ARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. V erify proper operation after servicing. Ignitor Flame Sensor Pilot Assembly GRN ORG BLK ...

  • Hearth and Home Technologies CD4236MR - page 52

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 52 G. W all Switch Installation for Fan (Optional) If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.5): • The power supply for the appliance must be brought into a switch box. • The power can then be supplied from the switch box to ...

  • Hearth and Home Technologies CD4236MR - page 53

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 53 1 in. (25 mm) min. to perpendicular wall A 3-1/2 in. (89 mm) min. from fireplace opening to perpendicular wall B Mantel Leg or Perpendicular W all T op of Appliance Drywall A B Measured from top of hood (in inches) 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 5 5-1/2 6-1/4 ...

  • Hearth and Home Technologies CD4236MR - page 54

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 54 I. Place the Rockwool W ARNING! Risk of Explosion! Follow rockwool placement instructions. DO NOT place rockwool directly over burner ports. Replace rockwool material annually . Improperly placed rockwool interferes with proper burner operation. • Rockwool is shipped ...

  • Hearth and Home Technologies CD4236MR - page 55

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 55 Latches (both bottom and top) Glass Assembly J. Install the Log Assembly • Base logs have been permanently mounted on the grate assembly and should not be moved. See Figure 14.2. Figure 14.2 Base Logs Figure 14.4 Placing Right T op Log Figure 14.3 Placing Left T op L ...

  • Hearth and Home Technologies CD4236MR - page 56

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 56 L. Install T rim • Install optional trim/surround kits using the instructions included with the accessory . • Use non-combustible materials to cover the gap between the sheet rock and the appliance (if desired). • Do not obstruct or modify the air inlet/outlet la ...

  • Hearth and Home Technologies CD4236MR - page 57

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 57 Closed N. Air Shutter Setting Air shutter settings should be adjusted by a quali fi ed installer at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shut- ter for longer vertical runs. See Figure 14.13. • 16 f ...

  • Hearth and Home Technologies CD4236MR - page 58

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 58 A. Standing Pilot Ignition System 1 5 15 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service t ...

  • Hearth and Home Technologies CD4236MR - page 59

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 59 Symptom Possible Cause Corrective Action 3. (Continued) C. Failed valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter a the thermopile terminals. The millivolt meter should read greater than 125mV . If t ...

  • Hearth and Home Technologies CD4236MR - page 60

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 60 B. Intelli fi re Ignition System Symptom Possible Cause Corrective Action 1. Pilot won’t light. The ignitor/module makes noise, but no spark. A. Incorrect wiring. V erify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected to correct ...

  • Hearth and Home Technologies CD4236MR - page 61

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 61 B. Intelli fi re Ignition System (continued) Symptom Possible Cause Corrective Action 4. Pilot lights but continues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot fl ame has been lit, fl ame recti fi cation has not occur ...

  • Hearth and Home Technologies CD4236MR - page 62

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 62 1 6 16 Reference Materials B 38-1/2 in. (978 mm) 33-1/2 in. (851 mm) 1-1/2 in. (38 mm) 27-1/4 in. (692 mm) 3 in. (76 mm) 6-1/2 in. (165 mm) 2-3/8 in. (60 mm) 14-1/8 in. (365 mm) 5-7/8 in. (149 mm) 2 in. (51 mm) C A 23 in. (584 mm) 15-1/4 in. (387 mm) Gas Line Access Al ...

  • Hearth and Home Technologies CD4236MR - page 63

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 63 B. V ent Components Diagrams Figure 16.2 DVP V ent Components Effective Height/Length DVP Pipe (see chart) Pi p e inches mm DVP4 4 102 DVP6 6 152 DVP12 12 3 05 DVP24 24 6 10 DVP36 36 9 14 DVP48 48 1219 DVP6A 3 - 6 76 - 152 DVP12A 3 - 12 76 - 305 Effective Height/Length ...

  • Hearth and Home Technologies CD4236MR - page 64

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 64 B. V ent Components Diagrams ( continued ) Figure 16.3 DVP V ent Components 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (698 mm) RF6M Roof Flashing Multi-pak 31 in. (787 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF12M Roof Flashing Multi-pak BEK T rap Cap Bric ...

  • Hearth and Home Technologies CD4236MR - page 65

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 65 B. V ent Components Diagrams ( continued ) Figure 16.4 DVP V ent Components DVP-TB1 Basement V ent Cap 12 in. (305 mm) 1-1/2 in. (38 mm) 7-3/8 in. (187 mm) 14 in. (356 mm) 17-3/4 in. (451 mm) 10-1/2 in. (267 mm) 3-7/8 in. (98 mm) DVP-TV V ertical T ermination Cap PVK-8 ...

  • Hearth and Home Technologies CD4236MR - page 66

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 66 B. V ent Components Diagrams ( continued ) Figure 16.5 DVP V ent Components DVP-TRAP1 DVP-TRAP2 DVP-HPC1 DVP-HPC2 DVP-TRAPK1 DVP-TRAPK2 DVP-TRAP Horizontal T ermination Cap 15-1/8 in. (384 mm) 12 in. (305 mm) 8 in. (203 mm) Max Effective Length Note: Heat shields MUST ...

  • Hearth and Home Technologies CD4236MR - page 67

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 67 B. V ent Components Diagrams (continued) Figure 16.6 DVP V ent Components 13 in. (330 mm) 15 in. (381 mm) 8-1/8 in. (206 mm) DVP-HRC-SS 10-7/8 in. 276 mm 10-1/2 in. 267 mm 3° 87° Effective Length 5-3/4 to 8-3/8 in. 146 to 213 mm 5-1/2 in. 140 mm 8-3/8 in. 213 mm DVP- ...

  • Hearth and Home Technologies CD4236MR - page 68

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 68 B. V ent Components Diagrams (continued) Figure 16.7 SLP Series V ent Components 8-3/4 in. 222 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 6 in. 152 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 9-7/8 in. 251 mm 6-1/2 in. 165 mm 9-1/4 in. 235 mm SLP-45 - 45° Elbow SLP-90ST - 90° Elb ...

  • Hearth and Home Technologies CD4236MR - page 69

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 69 B. V ent Components Diagrams (continued) Figure 16.8 SLP Series V ent Components SL-2DVP Adapter SLK-SNKD Snorkel T ermination Cap SLP-TVHW V ertical T ermination Cap PVK-80 Power V ent DVP-FBHT Firebrick T ermination Cap (This termination cap requires an SL-2DVP adapt ...

  • Hearth and Home Technologies CD4236MR - page 70

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 70 C. Service Parts CD4236M Series Service Parts # Description of Part COMMENTS CD4236MR CD4236MLR CD4236MIR CD4236MILR Qty . 1 Flue Adapter Plate 25882 25882 25882 25882 1 2 Flue Cover 34916 34916 34916 34916 1 3 Flue Adapter Plate w/Hole 4000-226 4000-226 4000-226 4000- ...

  • Hearth and Home Technologies CD4236MR - page 71

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 71 CD4842M Series Service Parts C. Service Parts (continued) # Description of Part COMMENTS CD4842MR CD4842MLR CD4842MIR CD4842MILR Qty . 1 Flue Adapter Plate 25882 25882 25882 25882 1 2 Flue Cover 34916 34916 34916 34916 1 3 Flue Adapter Plate w/Hole 4000-226 4000-226 40 ...

  • Hearth and Home Technologies CD4236MR - page 72

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 72 CD4236M Series Service Parts C. Service Parts (continued) # Description of Part Comments CD4236MR CD4236MLR CD4236MIR CD4236MILR Qty . V alve Assembly 4040-061 4040-062 4040-063 4040-064 1 1 Flex Ball V alve Assembly 302-320A 302-320A 302-320A 302-320A 1 2 V alve 230-0 ...

  • Hearth and Home Technologies CD4236MR - page 73

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 73 CD4842M Series Service Parts C. Service Parts (continued) 5 13 11 10 14 15 7 9 8 12 6 4 2 3 1 5 10 11 8 15 7 16 6 4 2 3 1 9 Standing Pilot V alve Assembly IPI V alve Assembly # Description of Part Comments CD4842MR CD4842MLR CD4842MIR CD4842MILR Qty . V alve Assembly 4 ...

  • Hearth and Home Technologies CD4236MR - page 74

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 74 D. Optional Components Arts & Crafts Faux Front FFCAC Modernist Faux Front FFCM Jamestown Faux Front FFCJ WTBC36D 36 in. Weathered Brick Refractory Liner Kit WTBC42D 42 in. Weathered Brick Refractory Liner Kit ...

  • Hearth and Home Technologies CD4236MR - page 75

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 75 D. Optional Components (continued) CD4842M 47 in. Caliber T op-Rear Direct V ent Cir- culating Gas Appliance CD4236M 41 in. Caliber T op/Rear Direct V ent Cir- culating Gas Appliance Model # Description FFCM36 Modernist-style black decorative faux front FFCM36PT Modern ...

  • Hearth and Home Technologies CD4236MR - page 76

    Heatilator • Caliber Mesh CD Series-SIT V alve • 4040-849 Rev J • 06/08 76 E. Contact Information Please contact your Heatilator dealer with any questions or concerns. For the location of your nearest Heatilator dealer , please visit www .heatilator .com. - NOTES - ______________________________________________________________________________ ...

Manufacturer Hearth and Home Technologies Category Indoor Fireplace

Documents that we receive from a manufacturer of a Hearth and Home Technologies CD4236MR can be divided into several groups. They are, among others:
- Hearth and Home Technologies technical drawings
- CD4236MR manuals
- Hearth and Home Technologies product data sheets
- information booklets
- or energy labels Hearth and Home Technologies CD4236MR
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hearth and Home Technologies CD4236MR.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hearth and Home Technologies CD4236MR, service manual, brief instructions and user manuals Hearth and Home Technologies CD4236MR. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hearth and Home Technologies CD4236MR.

A complete manual for the device Hearth and Home Technologies CD4236MR, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hearth and Home Technologies CD4236MR by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hearth and Home Technologies CD4236MR.

A complete Hearth and Home Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hearth and Home Technologies CD4236MR - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hearth and Home Technologies CD4236MR, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hearth and Home Technologies CD4236MR, that we can find in the current document
3. Tips how to use the basic functions of the device Hearth and Home Technologies CD4236MR - which should help us in our first steps of using Hearth and Home Technologies CD4236MR
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hearth and Home Technologies CD4236MR
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hearth and Home Technologies CD4236MR in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hearth and Home Technologies CD4236MR?

Use the form below

If you did not solve your problem by using a manual Hearth and Home Technologies CD4236MR, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies CD4236MR it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)