Manual NetComm NP2008

12 pages 1.28 mb
Download

Go to site of 12

Summary
  • NetComm NP2008 - page 1

    NetComm Limited 2~6 Orion Road, Lane Cove, NSW, 2066 Tel: (02) 9424 - 2070, Fax: (02) 9424 - 2010 Web: www.netcomm.com.au User Installation Guide NP2008 8 - Port Net work SmartS witch ...

  • NetComm NP2008 - page 2

    Table of Contents Table of contents Page 2 Introduction Page 3 Key features Page 3 Package contents Page 4 Front panel Page 4 LED’s Page 4 Rear panel Page 5 RJ - 45 Network ports Page 5 Twisted pair cables Page 5 Straight and crossover cable configuration Page 6 Application examples Page 6 Preparation before connecting your switch Page 7 Attachin ...

  • NetComm NP2008 - page 3

    Introduction Your NetComm™ NP2008 8 port 10/100 Ethernet Switch provides you with a cost effective, high - performance network sw itching solution for the home or small office. It is designed to automatically support network users operating at any combinatio n of 10 megabits per second (Mbps) or 100 Mbps. W ith features such as auto - negotiation ...

  • NetComm NP2008 - page 4

    Package contents Your package will contain the following: • NP2008 switch • User installation guide • Power Supply • Self adhesive rub ber feet • Wall mounting plugs and screws Front panel The front panel of the NP2008 switch contains LED’s corresponding to each network port located on the back of the hub: • 100 Mbps (10 Mbps). • Li ...

  • NetComm NP2008 - page 5

    R ear panel The rear panel of the NP2008 switch has eight auto - sensing 10/100 Mbps Ethernet ports and a power jack for connection of the supplied plug - pack. RJ - 45 Network ports All of the ports on the NP2008 are 10/100 Mbps capable auto - sensing Ethernet ports. Each port supports only unshielded twisted pair (UTP) cable using an 8 - pin RJ - ...

  • NetComm NP2008 - page 6

    S traight and crossover cable configuration For two devices to communicate, the transmitter of each device must be co n- nected to the receiver of the other device. The crossover function is usually implemented internally as part of the circuitry in the device. Most ports on switches and repeaters have media - dependent interfaces with crossover po ...

  • NetComm NP2008 - page 7

    Basic Desktop Network Switch The NP2008 switch is used as a desktop switch to build a small network that enables its users to have 100 Mbps access to other PC’s on the ne t- work and share files and resources. Preparation before connecting your switch Before you install your switch, prepare for the installation. Make sure you will be operating th ...

  • NetComm NP2008 - page 8

    A ttaching computers to the switch 1. Install a 10/100Mbps (10/100Base - TX) network adapter card into every computer you want to attach to the network. Make sure you install the Network adaptor drivers in accordance with the manufa c- turers directions. 2. Prepare the twisted - pair cables with RJ - 45 plugs on each end. Use Category 5/5e cable fo ...

  • NetComm NP2008 - page 9

    C ascading the switch When attaching the NP2008 switch to an additional switch, router or other devices, be sure to verify the port type implemented before co n- nec t ing any cable. A) Connecting the NP2008 to another NP2008: Your NP2008 switch supports a switch selectable UP - Link port, port 8 located on the rear of the switch. To connect one sw ...

  • NetComm NP2008 - page 10

    1. Locate the UP - Link slide switch located on the right hand side of the switch case. 2. Slide the selection switch to the UP - Link pos ition. 3. Connect one end of a straight through cable to the number 8 port on the first NP2008 switch. 4. Connect the other end of the straight through cable to any port of the second NP2008 switch, see previous ...

  • NetComm NP2008 - page 11

    Specifications of the switch Standard IEEE802.3 10Base - T Ethernet IEEE 802.3u & 802.3x 100 Base - TX Fast Ethernet Network Interface Eight 100BASE - TX / 10BASE - T N - Wa y ports Data Transfer Rate Ethernet: 10Mbps (half duplex) 20Mbps (full duplex) Fast Ethernet: 100Mbps (half duplex) 200Mbps (full duplex) Network Cable 10 BASE - T: Cat.3, ...

  • NetComm NP2008 - page 12

    C - Tick Mark declaration of conformance This is to certify that this product complies with the Australian C - Tick sta n dard where applicable. Warning Do not plug a phone jack connector into any of th e RJ - 45 port. This may damage the switch. Sta tement of conditions In the interest of improving internal design, operational function, and/or rel ...

Manufacturer NetComm Category Switch

Documents that we receive from a manufacturer of a NetComm NP2008 can be divided into several groups. They are, among others:
- NetComm technical drawings
- NP2008 manuals
- NetComm product data sheets
- information booklets
- or energy labels NetComm NP2008
All of them are important, but the most important information from the point of view of use of the device are in the user manual NetComm NP2008.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals NetComm NP2008, service manual, brief instructions and user manuals NetComm NP2008. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product NetComm NP2008.

Similar manuals

A complete manual for the device NetComm NP2008, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use NetComm NP2008 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of NetComm NP2008.

A complete NetComm manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual NetComm NP2008 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the NetComm NP2008, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the NetComm NP2008, that we can find in the current document
3. Tips how to use the basic functions of the device NetComm NP2008 - which should help us in our first steps of using NetComm NP2008
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with NetComm NP2008
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of NetComm NP2008 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning NetComm NP2008?

Use the form below

If you did not solve your problem by using a manual NetComm NP2008, ask a question using the form below. If a user had a similar problem with NetComm NP2008 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)