Manual Oki BISM2

34 pages 1.01 mb
Download

Go to site of 34

Summary
  • Oki BISM2 - page 1

    www.ezurio.com BISM2 Bluetooth™ V ersion 2.0 Serial Module 1. General Descr iption Ezurio’s BIS M2 Bluetooth Serial Module is a fully integrated and qualified Class 1 Bluetooth solution designed for lowest cost of integration and ownership for designers wishing to incorporate Blueto oth functionality into their products. The module is qualified ...

  • Oki BISM2 - page 2

    www.ezurio.com 2. Features Feature Implementation Bluetooth Transmission Class 1 Fully Bluetooth pre-qualified Bluetooth 2.0 Range 250 metres typical (free space) Frequency 2.400 – 2.485 GHz Max Transmit Power +6dBm Min Transmit Power -27dBm Receive Sensitivity Better than -86dB Data Transfer rate Up to 300Kbp s Serial Interface RS-232 bi-direct ...

  • Oki BISM2 - page 3

    www.ezurio.com 3. Functional Block Diagram 3.1 Connection Diagram The Module is equipped with a 40-pin 0.5mm pitch board-to -board connector that connects to the applicati on platform. ...

  • Oki BISM2 - page 4

    www.ezurio.com 3.2 Pin Descrip tions The Hirose DF12C board-to-bo ard connector on the module is a 40-pin double-row recept acle. The table below defines the pin functions. Note that this pin-out is as viewed from the underside of the Module. Pin No. Signal Description Pin No. Signal Description 1 Analogue 0 1.8v Max 2 GPIO1 I/O for Host. 3 Analogu ...

  • Oki BISM2 - page 5

    www.ezurio.com Pin 8 (UART_DCD) is active low. It is n ormally 3.3v. When a conn ection is live this pin is low. This means that when this pin is converted to RS232 voltag e levels it will have the correct volt age level for assertion. Pin 10 (UART_DSR) is an input, with active low logic. It should be connected to the DTR output of the host. When t ...

  • Oki BISM2 - page 6

    www.ezurio.com UART_RTS 23 O V OL max=0.2V V OH min=2.8V UART_DSR 10 I V IL max=0.8V V IH min=2.1V V IH max=3.7V UART_DTR 12 O V OL max=0 .2V V OH min=2.8V Shared with GPIO3 UART_RI 6 I or O O/P : V OL max=0.2V V OH min=2.8V I/P : V IL max=0.8V V IH min =2.1V V IH max=3.7V Directio n may be programmed. UART_DCD 8 I or O O/P : V OL max=0 .2V V OH mi ...

  • Oki BISM2 - page 7

    www.ezurio.com 3.3.2.4 PCM Interface Signal Name Pin No I/O Signal level Com ments PCM_CLK 20 I or O O/P : V OL max=0.2 V V OH min=2.8V I/P : V IL max=0.8V V IH min =2.1V V IH max=3.7V If un used keep pins open PCM_IN 22 I V IL max=0.8V V IH min=2.1V V IH max=3.7V PCM_SYNC 24 I or O O/P : V OL max=0.2V V OH min=2.8V I/P : V IL max=0.8V V IH min =2. ...

  • Oki BISM2 - page 8

    www.ezurio.com 4. I/O Characteristics 4.1 Power Consumption The current drain from the Vc c power input line is dependent on various factors. The three most significant factors are the voltage level at Vcc, UA RT Baudrate and the operating mode. The hardware specification for the Module allows for a voltage range of 3.6 to 7.0 at Vcc. Tests have sh ...

  • Oki BISM2 - page 9

    www.ezurio.com 5. DC Characteristics 5.1 RF Performance 5.1.1 Transmit Power Conduc ted Transmit Pow er min: 1.0mW (0dBm) max: 4mW (6dBm) Antenna Gain +2dBi typ. Effective Transmit Power min:0dBm Max: +6dBm Output power can be reduced by program control 5.1.2 Receive Sensitivity Receive Sensitivity -86dBm (at 25°C) Antenna Gain +2dBi typ Effective ...

  • Oki BISM2 - page 10

    www.ezurio.com Data Transfer Ra te / Distance 0 100 200 300 400 500 600 700 800 10m 50m 100m 150m 200m 250m 300m Distance (meters) Data Transfer Rate (kbps) RF data rate Serial port data rate 5.3 Temperature Pe rformance Data Transmit Rate with Temperature and Attenuation 0 100 200 300 400 500 600 700 800 -60dBm -65dBm -70dBm -75dBm -80dBm -85dBm - ...

  • Oki BISM2 - page 11

    www.ezurio.com Serial Module UART Interface UART_TX UART_RX UART_CTS UART_RTS UART_DSR UART_DTR UART_RI UART_DCD /RXD /TXD /RTS /CTS /DTR /DSR /RING /DCD RS232 Interface 6. Functional Description The BISM 2 Bluetooth module is a self-contai ned Bluetooth product and requires only power to implement full Bluetoo th communication. The integrated, hig ...

  • Oki BISM2 - page 12

    www.ezurio.com 6.1.2 SPI bus The Module is a slave device that uses terminals SPI_MOSI , SPI_MI SO, SPI _CLK and SPI_CS B. This interface is used for program firmware updates at the factory. Ezurio supply a PC based utility to all ow firmware upgrade over the UART port. It is h ighly recommended that customers should use this method for updating fi ...

  • Oki BISM2 - page 13

    www.ezurio.com 7. Integrated Firmware 7.1 General The BISM 2 has been designed to provide t he fastest route to market for designers who wish to use Bluetooth to wirel essly enable their products. To achieve this Ezurio has implemented a wide ranging set of AT commands that control all of the standard Bluetooth tasks. These remove the complexity of ...

  • Oki BISM2 - page 14

    www.ezurio.com ATD00809844EA 13 to the UART of the BISM 2 module. The module will attempt to make a connection and return conn ect 0080984 4ea13,1101 ) or (NO CARRI ER), depending on wh ether the connection was successful. The scope of the AT command set developed by Ezurio is such that most Bluetooth functionality can be covered, greatly reducing ...

  • Oki BISM2 - page 15

    www.ezurio.com 7.3.1.5 Bluetooth • Set the module to be a master or slave • Make a Bluetooth connection to a specified device • Perform a full inquiry f or other Bluetoot h devices • Query a remote device to check if a service is offered • Fetch the friendly name of a remote device • Increase or decrease the delay before the master aban ...

  • Oki BISM2 - page 16

    www.ezurio.com 8. Low Power Modes The current drain from the Vc c power input line is dependent on various factors. The three most significant factors are the voltage level at Vcc, UA RT baud rate and the operating mode. The hardware specification for the blu2i module allows for a voltage range of 3.6 to 7.0v at Vcc. Tests have shown that there is ...

  • Oki BISM2 - page 17

    www.ezurio.com A slave on the other hand does NOT h ave prior knowledge of when a pack et will be recei ved and has to assume that a packet will be received from a master on every receive slot. This means that it has to leave its recei ving circuitry on for most of the receive slot duration. The result of this is high power consumption as illustrat ...

  • Oki BISM2 - page 18

    www.ezurio.com 9. Application E xamples 9.1 RS232 Modem Signals Just as a telephony modem has control and status lines, the blu2i Module also provides for 6 control and status lines as per the table below. The direction column is as seen from the module’s viewpoint. Direction Function IN or OUT * CI also known as RI (Ring Indicate) IN or OUT * DC ...

  • Oki BISM2 - page 19

    www.ezurio.com 3. PIO3 (DCD) w ill be de-assert ed when the device is in the un connected state. Asserted when a connection is active. See S Registers 552 and 553 for more detai ls. 4. PIO5 is either used as GPI O or driven as UART_DTR . When the u nit is configured in pure host mode, this pin is forced into UART_DTR and is asserted when there is a ...

  • Oki BISM2 - page 20

    www.ezurio.com commands. This further mean s that in stand alone mode, the DSR input line MUST be asserted e.g. 0V in TTL signal mode. The slave is configured by: AT&F* ATS512=4 ATS0=-1 AT&W AT+BTR<bdaddr_m> Where <bdaddr_m> is optional. If it is not specified, then the slave unit will accept connections from any device. If spec ...

  • Oki BISM2 - page 21

    www.ezurio.com AT&W AT+BTR<bdaddr_m> 9.5 Modem Control and Status Signals A serial port has DTR, DSR, RT S, CTS, DCD and RI c ontrol lines. RTS and CTS are locally controll ed to prevent local buffer overflow. The status of DTR, DRS , DCD and RI can be exchan ged with the remote peer device . If f or example, the DTR/DSR lines are to be e ...

  • Oki BISM2 - page 22

    www.ezurio.com 10. Application Information 10.1 Antenna Position The antenna u sed on the BISM2 B luetoot h module is designed to be largel y immune from the effects of proximity detuning. Normally, antennas operating at 2.4GHz are affected by their surroun dings, so that great care is needed in their placeme nt and orientation. The BISM 2 can be u ...

  • Oki BISM2 - page 23

    www.ezurio.com 10.2 Power Supp ly Considerations The power supply for the Module has to be a single voltage source of Vcc within the ran ge of 3.6 V to 7.0 V. It must be able to provide sufficient current in a tran smit burst. This can rise to 65mA. The Module includes regulators to provid e local 3.3V. This rail is accessible on connector J2 for m ...

  • Oki BISM2 - page 24

    www.ezurio.com 10.5.1 Fixing Pillars Ezurio in conjunction with Rich co has designed a mounting pillar for use with the Bluetooth Serial Module. This allows the module to be securely held to a primary pcb using snap fit details. A variety of different heights are available to accommo date different variants of Hirose stacked connectors. Pillars sup ...

  • Oki BISM2 - page 25

    www.ezurio.com 11. Board to Board Connector This chapter provides specificatio ns for the 40-pin board-to-board connecto r which serves as physical interface to the host applicat ion. The receptacle assembled on the Module is Hirose type DF12C. Details are availabl e at: http://www.hirose.co.jp/cataloge_hp/e5 3700036 .pdf 11.1 Stacking Height Matin ...

  • Oki BISM2 - page 26

    www.ezurio.com Insulator Material PA , beige natural Stacking height 3.0 mm ; 3.5 mm ; 4.0 mm ; 5.0 mm Insertion force 21 .8N Withdrawal force 1st 10N Withdrawal force 50th 10N Maximum connection cycles 50 12. Qualification 12.1 Bluetooth Qualification Process The following safety precautions must be observed during all phases of the operation, usa ...

  • Oki BISM2 - page 27

    www.ezurio.com 12.4 Safety and Regulatory Statements 12.4.1 Europe – EU De claration of Conformity DECLARATION OF CONFORMITY In accordance with Annex I V of the EU direc tive 1999/5/EC Ezurio declare under our r esponsibility that th e BISM2 Module complies with the appropriate essential requirements of the Article 3 of the R&TTE and the othe ...

  • Oki BISM2 - page 28

    www.ezurio.com 12.4.2 FCC and Industry Canada Statements This device complies with part 15 of the FCC Rules. Operation is subject to the follo wing two conditions: (1) This device may not cause harmful in terference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modi ...

  • Oki BISM2 - page 29

    www.ezurio.com 14. Physical Dimensions 14.1 Mechanical Dimensions 14.1.1 Standard Module Location of Connector (Bottom View) All dimensions in mm ...

  • Oki BISM2 - page 30

    www.ezurio.com 14.2 BISM2 Module without antenna (spec ial order) The dimensions for this module are identical to the standard BISM 2 illustrated above, but the antenna is replaced with a U-FL connector. TOP VIEW The external antenna used mu st not result in an increased output power. I. e. the total gain of mating connector, cable and antenna must ...

  • Oki BISM2 - page 31

    www.ezurio.com Reel – Rienheimer Elektronic ( www.reel-gmbh.de ) manufacture a w ide range of antennae, including their planTEc roof antennae that are ideal for vehicle mounting. Part Number M70CXR 0300 00 XX XX (Contact Reel for availabili ty of a U.FL connection and exact part number) Pacific Wireless ( www.pacwireless.com ) supply a wide range ...

  • Oki BISM2 - page 32

    www.ezurio.com SIDE VIEW All dimensions in mm. 14.4 Labelling The label contains the Part number and the un ique Bluetooth address of the module. 14.5 Ordering Information The BISM 2 is available with different variants of engineering or production firmware. Ordering information is provided below: Part Number Description Firmware Version TRBLU23-00 ...

  • Oki BISM2 - page 33

    www.ezurio.com 15. Related Documents • blu2i AT Command Set Version 2.11.0 Reference Manua l • blu2i Firmware Release Notes Versio n 2.11.0 • blu2i Multipoint Firmware Reference Manual • BISM Bluetooth Serial Module - Quick S tart Guide • BISM Bluetooth Serial Module - FAQ • Blu2i Application Scenarios • Wireless Develope r’s Kit Us ...

  • Oki BISM2 - page 34

    www.ezurio.com b) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Ezurio does not assume responsibilit y for use of an y of the circuitry described, no circuit patent licen ...

Manufacturer Oki Category Switch

Documents that we receive from a manufacturer of a Oki BISM2 can be divided into several groups. They are, among others:
- Oki technical drawings
- BISM2 manuals
- Oki product data sheets
- information booklets
- or energy labels Oki BISM2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Oki BISM2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Oki BISM2, service manual, brief instructions and user manuals Oki BISM2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Oki BISM2.

Similar manuals

A complete manual for the device Oki BISM2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Oki BISM2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Oki BISM2.

A complete Oki manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Oki BISM2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Oki BISM2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Oki BISM2, that we can find in the current document
3. Tips how to use the basic functions of the device Oki BISM2 - which should help us in our first steps of using Oki BISM2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Oki BISM2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Oki BISM2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Oki BISM2?

Use the form below

If you did not solve your problem by using a manual Oki BISM2, ask a question using the form below. If a user had a similar problem with Oki BISM2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)