English dropdown-ico

Manual Craftsman 137.24884

30 pages 5.61 mb
Download

Go to site of 30

Summary
  • Craftsman 137.24884 - page 1

    Operator's Manual ® 10 in. TABLE SAW Model No. 137.248840 CAUTION: Before using this Table Saw, read this manual and follow all its Safety Rules and Operating Instructions ® Safety Instructions ® Installation ® Operation ® Maintenance ® Parts List Customer Help Line 1 o800o843ol 682 Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA V ...

  • Craftsman 137.24884 - page 2

    SECTION PAGE Warranty ............................................................. 2 Product Specifications ........................................ 2 Power Tool Safety .............................................. 3 Table Saw Safety ................................................ 4 Electrical Requirements and Safety .................... 5 Acces ...

  • Craftsman 137.24884 - page 3

    la, WARNING n Before using your tabJe saw, it is critical that you read and understand these safety rules. Failure to follow these rules couJd result in serious injury or damage to the table saw. Good safety practices are a combination of common 16. REMOVE ADJUSTING KEYS AND WRENCHES. sense, staying alert and understanding how to use your power too ...

  • Craftsman 137.24884 - page 4

    1. ALWAYS USE SAW BLADE GUARD, splitter and anti-kickback pawls forevery operation for which they can be used, including through-sawing. Through-sawing operations are those in which the blade cuts completely through the workpiece when ripping or cross-cutting. 2. ALWAYS HOLD WORK FIRMLY against the miter gauge or rip fence. functioning. Do not rele ...

  • Craftsman 137.24884 - page 5

    GROUND(NG (NSTRUCT(ONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric currents and reduces the risk of electric shock. This tool is equipped with an electrical cord that has an equipmentogrounding conductor and a grounding p(ug. The p(ug must be plugged into a matching receptac(e that is prope ...

  • Craftsman 137.24884 - page 6

    RECOMMENDED ACCESSORIES IA WARNING I Visit your Scars Hardware Department or see the Scars Power and Hand TooJ Catalog to purchase recommended accessories for this power tool IA WARNING n To avoid the risk of personal injury, do not modify this power tool or use accessories not recommended by Sears. To avoid the risk of personal injury: o Do not us ...

  • Craftsman 137.24884 - page 7

    UNPACKING YOUR TABLE SAW A B G H C D ®® M O P Q o 0 0 U R S V W X ...

  • Craftsman 137.24884 - page 8

    Blade Guard # Extension Wing Locking Overload Reset Switch Blade Tilt Pointer & Scale ON/OFF Switch with Saftey Key Blade Elevation Handwheel Table insert Rip Fence Side Table Extension Wing Bevel Tilting Handwheel Blade Bevel Lock Knob Miter Gauge Table Rear Outfeed Table Extension Mounting Holes Stand Dust Bag ...

  • Craftsman 137.24884 - page 9

    ANTFKICKBACK PAWLS = Prevents the work piece from being kicked upward or back toward the front of the table saw by the spinning blade. ON/OFF SWITCH = Contains a built-in safety switch key. To lock the switch in the OFF position, remove the switch key from the switch. ARBOR = The shaft onwhich the blade or dado is mounted. BEVEL CUT = An angle cut ...

  • Craftsman 137.24884 - page 10

    ASSEMBLE STAND (FIG. A) 1 Unpack all parts and group by type andsize Refer to the parts !istfor correct quantities 2 Attach onelong upper support (S)to top of leg(V) using onebolt (1) andnut (2) NOTE: Do not tighten bolts until stand is properly aligned (see step #9 before tightening) 3 Attach other end of Io% upper support to top of another legusi ...

  • Craftsman 137.24884 - page 11

    MOUNT SAW ONWORK SURFACE (FIG. C) 1. If the legsetwill not beused, the sawmust be properly secured to a sturdy workbench using the four mounting holes at the base of the saw. 2. The surface ofthe table where the saw is to be mounted must have a hole large enough to facilitate sawdust %Fthrough andremoval & Square the saw on the mounting surface ...

  • Craftsman 137.24884 - page 12

    RIP FENCE (Fig, G) 1. Lift upward on the ripfence handle (1) so the rear holding clamp (2) is fully extended. 2. Place the rip fence on the saw table, lowering the front of the fence onto the table first. 3. Push down on the fence handle (1) to lock. Fig. G 4. Remove the arbor nut (5) and outer flange (6) (Fig. I). 5. install the saw blade onto the ...

  • Craftsman 137.24884 - page 13

    BLADE GUARD ASSEMBLY (FIG. K, L, M) 1. Setthe blade to maximum height and the tilt to zero degrees on the bevel scale with the hand wheels. Lock the blade bevel lock knob. 2. Place the spring washer (2), flatwasher (3), external tooth lock washer (4) ontotheblade guard mounting bolt (1) (Fig. K). 3. Insert bolt and washer assembly through splitter ...

  • Craftsman 137.24884 - page 14

    iNSTALLiNG THE TABLE SIDE EXTENS!ONS- cont'd (FIG. O} 6. Snap one short location seat (1) over the end of the rear table extension tube (2). Make sure the locating pin (3) in the location seat fits into the matching hole in the extension tube (Fig. O). 7. install the left hand table extension the same manner. NOTE: For i!tustration purposes, t ...

  • Craftsman 137.24884 - page 15

    RiP FENCE iNDiCATOR ADJUSTMENT (FIG. Q) 1_ The rip fence indicator (6) points to themeasurement scale. The scale shows the distance from theside of the fence to nearest side of the blade. 2_ Measure the actual distance with a rule. if there is a difference between the measurement andthe indicator, adjust the indicator (6)_ 3_ Loosen the screw (7) a ...

  • Craftsman 137.24884 - page 16

    BLADE PARALLEL TOTHE MITER GAUGE GROOVE (FIG. U, V) I_WARNiNG This adjustment was made at the factory, but it should be rechecked and adjusted if necessary. IA waRninG n To prevent personal injury: o Always disconnect plug from the power source when making any adjustments. o This adjustment must be correct or kickback could result in a serious inju ...

  • Craftsman 137.24884 - page 17

    8ASmC SAW OPERATmONS RAISE THE BLADE (FIG. W) To raise or lower the blade, turn the blade elevation handwheel (1) to the desired blade height, and then tighten lock handle (2) to maintain the desired blade angle. Fig. W 2 TILTING THE BLADE (FIG. W) 1. To tilt the saw blade for bevel cutting, loosen the bevel lock knob (2) and turn the tilting handw ...

  • Craftsman 137.24884 - page 18

    CUTTING OPERATIONS There are two basic types of cuts: ripping and crosscutting. Ripping is cutting along the length andthe grain of the workpiece. Crosscutting is cutting either across the width or across the grain of the workpiece. Neither ripping nor crosscutting may be done safely freehand. Ripping requires the use of the ripfence, and crosscutt ...

  • Craftsman 137.24884 - page 19

    REVEL RiPPiNG This cutis the same as ripping except the blade bevel angle is set to an angle other than "0". la, WARNING n Cut only with the workpiece and the fence on the right aide of the blade. RiPPiNG SMALL PIECES IA wAR.I.G n Avoid injury from the blade contact. Never make through saw cuts narrower than 1/2 in. wide. 1. it is unsafe ...

  • Craftsman 137.24884 - page 20

    COMPOUND MITER CROSSCUTTING (FIG. FF) 0°~45 ° BLADE BEVEL & 00~45 ° MITER ANGLE This sawing operation is combining a miter angle with o bevel angle. IA WARNING n Always work to the right side of the blade during this type of cut. The miter gauge must be in the right side groove because the beveJ angle may cause the blade guard to interfere w ...

  • Craftsman 137.24884 - page 21

    Attach auxiliary fence to ripfence withtwo "C"clamps. (Fig. dd) Fig. JJ DADO CUTS (FIG. KK) IA WARNING n a. Only Stackable dado blades can be used on this SaW. b. DO NOT use Adjustable or Wobble type dadoes. c. Maximum dado cut width is 1/2 in. 1. A dado table insert must be purchased separately for this saw to accept a dado blade. Remove ...

  • Craftsman 137.24884 - page 22

    GENERAL MAINTENANCE IA WARNING n For your own safety, turn the switch OFF and remove the switch kay. Remove the plug from the power source outlet before maintaining or lubricating your saw. 1. Clean out al! sawdust that has accumulated inside the saw cabinet and the motor. 2. Polish the saw table with an automotive wax to keep it clean and to make ...

  • Craftsman 137.24884 - page 23

    IA WARNmNG n To avoidinjury from an accidental start, turn theswitch "OFF" and always remove the plug from the power source before making any adjustments_ ® Consult your !ocal Sears Service Center if for any reason the motor wil! not run. SYMPTOM Saw will not starL iDoes not make accurate 45 ° _nd 90 ° rip cuts. iMateria! pinched blade ...

  • Craftsman 137.24884 - page 24

    t0 in. TABLE SAW MODEL NO. t37.248840 [A WAR.I.G [ When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at y ...

  • Craftsman 137.24884 - page 25

    10 in. TABLE SAW MODEL NO. 137.248840 SCHEMATIC FOR SAW [ [ [ OKAP OBCW 2 2179 09JK OB3R 0J76 0JAA _" IOGP / V 20KA 2CWN 0J76 OBPA OBAE_ 0B99 OKMR ...

  • Craftsman 137.24884 - page 26

    10 in. TABLE SAW MODEL NO. 137.248840 PARTS LIST AND SCHEMATIC FOR STAND I.D. NO DescripJJon Size 09D6 FOOT PAD 0A4T FENCE STORAGE CLiP 0EAA BRACKET #AW 0EAN UPPER SUPPORT #AW 0EAP UPPER SUPPORT #AW 0EAY UPPER SUPPORT #AW 0EBB BOTTOM SUPPORT BRACKET #AW 0EBG BOTTOM SUPPORT BRACKET #AW 0J4F FLAT WASHER (pSX16=2_5 0J4J FLAT WASHER cp 10X20-2 0JPP HEX ...

  • Craftsman 137.24884 - page 27

    10 in. TABLE SAW MODEL NO. 137.248840 PARTS LIST AND SCHEMATIC FOR MOTOR i.D. NO Descdp_ion 0HV8 BALL BEARING 0HVU BALL BEARING 0HXg NEEDLE BEARING 0JAL EXT.TOOTH LOCK WASHER 0JX3 HEX. SOC. SET SCREW 0K3A CR,RE. PAN HD. SCREW & WASHER 0KSV CR,-RE. COUND.HDSCREW 0KCP CRRE. PAN HEAD TAPPING & WASHER SCREW 0KTH STRAIN RELIEF 0QEg MOTOR NAMEPLA ...

  • Craftsman 137.24884 - page 28

    PUSH STICK CONSTRUCTION ® This is a full°size drawing (actual size) ® Use good quality plywood or sotid wood ® Use %" or ¾" material e Push stick MUST be thinner than the width of materiat being cut / / / / ! J i I Cut Here To P_h ½" Wood Cut Here To Push ¾" Wood Jotch To Prevent Hand From Slipping ...

  • Craftsman 137.24884 - page 29

    ...

  • Craftsman 137.24884 - page 30

    Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who soJd it! For the replacement parts, accessories and Operator's Manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage ...

Manufacturer Craftsman Category Saw

Documents that we receive from a manufacturer of a Craftsman 137.24884 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 137.24884 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 137.24884
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 137.24884.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 137.24884, service manual, brief instructions and user manuals Craftsman 137.24884. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 137.24884.

Similar manuals

A complete manual for the device Craftsman 137.24884, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 137.24884 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 137.24884.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 137.24884 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 137.24884, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 137.24884, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 137.24884 - which should help us in our first steps of using Craftsman 137.24884
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 137.24884
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 137.24884 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 137.24884?

Use the form below

If you did not solve your problem by using a manual Craftsman 137.24884, ask a question using the form below. If a user had a similar problem with Craftsman 137.24884 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)