English dropdown-ico

Manual Vermont Casting 20DVT

32 pages 3.67 mb
Download

Go to site of 32

Summary
  • Vermont Casting 20DVT - page 1

    DO NOT ST ORE OR USE GASOLINE OR OTHER FLAMMABLE V APORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. WHA T TO DO IF YOU SMELL GAS: • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from your neighbor ’s phone. Follow the gas su ...

  • Vermont Casting 20DVT - page 2

    Br ookh av e n Dir ect V ent Gas F ireplace 2 10009459 PLEASE READ THE INST ALLA TION & OPERA TING INSTRUCTIONS BEFORE USING APPLIANCE. Thank you and congratulations on your purchase of a CFM Corporation fireplace. IMPORT ANT : Read all instructions and warnings carefully before starting installation. Failure to follow these instructions fully ...

  • Vermont Casting 20DVT - page 3

    10009459 3 Br ookh av e n Dir ect V ent Gas F ireplace This gas appliance should be installed by a qualified installer in accordance with local building codes and with current CSA-B149.1 Installation codes for Gas Burning Appliances and Equipment. For USA Installations follow local codes and/or the current National Fuel Gas Code. ANSI Z223.1/NFP A ...

  • Vermont Casting 20DVT - page 4

    Br ookh av e n Dir ect V ent Gas F ireplace 4 10009459 Ref. 20DVT A 20” (508 mm) B 29 ¹⁄₂ ” (749 mm) C 13 ¹⁄₂ ” (343 mm) D 19 ³⁄₄ ” (502 mm) E 14 ³⁄₄ ” (375 mm) F 15” (381 mm) G 1 ¹⁄₂ ” (38 mm) H 4 ¹⁄₄ ” (108 mm) I 6 ³⁄₄ ” (171 mm) J 32 ¹⁄₂ ” (826 mm) K 8” (203 mm) Framing Dimensions L 3 ...

  • Vermont Casting 20DVT - page 5

    10009459 5 Br ookh av e n Dir ect V ent Gas F ireplace T op of Unit to Ceiling ................................ 32” (813 mm) Front of Unit to Combustibles ................... 36” (914 mm) Appliance T op of Standoff ......................................... 0” (0 mm) Bottom ...................................................... 0” (0 mm) Sid ...

  • Vermont Casting 20DVT - page 6

    Br ookh av e n Dir ect V ent Gas F ireplace 6 10009459 Framing and Finishing Check fireplace to make sure it is levelled and properly positioned. T o mount the appliance: 1. Choose the location. 2. This unit comes with four (4) flanges pre-mounted on both sides of the fireplace to allow two different drywall thicknesses to be used. Flange “A? ...

  • Vermont Casting 20DVT - page 7

    10009459 7 Br ookh av e n Dir ect V ent Gas F ireplace FP297A INST A VENT FREE UVHB26 GAS SUPPL Y 7/1/98 FP297A 1/2” Gas Supply 1/2” NPT x 1/2” Flare Shut- off V alve 3/8” Flex Line (From V alve) Fig. 5 T ypical gas supply installation. The fireplace valve must not be subjected to any test pressures exceeding 1/2 psi. Isolate or disconnect ...

  • Vermont Casting 20DVT - page 8

    Br ookh av e n Dir ect V ent Gas F ireplace 8 10009459 V V V V V V V X X X D E B B B C B M B A J K F L VENT TERMINA TION AIR SUPPL Y INLET AREA WHERE TERMINAL IS NOT PERMITTED H I   Operable Operable Fixed Closed V B CFM145a DV T ermin Location 5/01/01 Rev . 12/05/01 sta INSIDE CORNER DET AIL V A G N N CFM145a Gener ...

  • Vermont Casting 20DVT - page 9

    10009459 9 Br ookh av e n Dir ect V ent Gas F ireplace Fig. 7a T ermination clearances. General Information Assembling V ent Pipes Canadian Installations: V enting system must be installed in accordance with the current CSA-B149.1 installation code. USA Installations: The venting system must conform with local codes and/ or the current National Fue ...

  • Vermont Casting 20DVT - page 10

    Br ookh av e n Dir ect V ent Gas F ireplace 10 10009459 The vent chart should be read in conjunction with the following vent installation instructions to determine the relationship of the vertical and horizontal dimensions of the vent system. 1. Determine the height of the center of the horizontal vent pipe exiting through the outer wall. Using thi ...

  • Vermont Casting 20DVT - page 11

    10009459 1 1 Br ookh av e n Dir ect V ent Gas F ireplace Horizontal plane means no vertical rise exists on this portion of the vent assembly . • The maximum number of 90° elbows per side wall installation is three (3). (Fig. 1 1) • If a 90° elbow is fitted directly on top of the fireplace flange, the maximum horizontal vent run before the ...

  • Vermont Casting 20DVT - page 12

    Br ookh av e n Dir ect V ent Gas F ireplace 12 10009459 VO584-100 V ent Opening 2/99 djt V ent Opening for Combustible W all 9 ³⁄₈ ” (240 mm) 9 ³⁄₈ ” (240 mm) Fireplace Hearth Framing Detail Opening for Noncombustible W all 7 ¹⁄₂ ” (190 mm) VO584-100 Fig. 15 Locate vent opening on wall. ZCS101 Zero Clearance Sleeve 3/1 1/99 djt ...

  • Vermont Casting 20DVT - page 13

    10009459 13 Br ookh av e n Dir ect V ent Gas F ireplace STEP 7 Apply high temperature sealant to 4” (102 mm) and 7” (178 mm) collars or the termination one inch away from the end. Guide the vent termination’s 4” and 7” collars into their respective vent pipes. Double check that the vent pipes overlap the collars by 2” (51 mm). Secure th ...

  • Vermont Casting 20DVT - page 14

    Br ookh av e n Dir ect V ent Gas F ireplace 14 10009459 3. Install vent system. See Page 12, Steps 2 through 5. 4. Ensure a watertight seal is made around the vent pipe coming through the wall. 5. Apply high temperature sealant caulking (supplied) around the 4” and 7” snorkel collars. 6. Slide the snorkel into the vent pipe and secure to the wa ...

  • Vermont Casting 20DVT - page 15

    10009459 15 Br ookh av e n Dir ect V ent Gas F ireplace 1 2 3 4 1 2 3 4 1 + 2 + 3 + 4 = 270° FP1 179 Fig. 24 Maximum elbow usage. FP 10 29 at ti c in su la tio n sh ie ld fi re st op s pa cer s 1/ 28 /0 0 dj t Joist Attic Insulation Shield Ceiling Installation Upper Floor 1 1” (279mm) Firestop Spacer Nails (4) Fig. 26 Place firestop spacer(s) a ...

  • Vermont Casting 20DVT - page 16

    Br ookh av e n Dir ect V ent Gas F ireplace 16 10009459 Starter Kit - Model 7TDVSK - Sidewall V enting (T wist Lock Pipe) Model 7FDVSK - Sidewall V enting (Flex V ent Pipe) Models 7TDVTK/TV - Hot T ouch T ermination Kits Model 7TDVTVTK/TV - Cool T ouch T ermination Kit Starter Kit - Model 7TDVSKV - V ertical V enting for 7TDVSKV -A order 1/12 to 6/ ...

  • Vermont Casting 20DVT - page 17

    10009459 17 Br ookh av e n Dir ect V ent Gas F ireplace Glass Information Only glass approved by CFM Corporation should be used on this fireplace. • The use of any non-approved replacement glass will void all product warranties. • Care must be taken to avoid breakage of the glass. • Do not operate appliance with glass front removed, cracked ...

  • Vermont Casting 20DVT - page 18

    Br ookh av e n Dir ect V ent Gas F ireplace 18 10009459 6. Place the log front (J12). Place the two underside holes of the log over the two pin studs of the bracket on the left and right sides of the front burner hous- ing. (Fig. 32) 7. Place ember material on top of burner . Scatter the ember material over the tiles on the front area of the burner ...

  • Vermont Casting 20DVT - page 19

    10009459 19 Br ookh av e n Dir ect V ent Gas F ireplace Large Lava Rock The large bag of lava rock provided with this fireplace must be placed on the firebox base around the sides of the burner assembly and on the tray beneath the grate. Under no circumstances should this large lava rock be placed on any part of the burner assembly . Fig. 34 Flam ...

  • Vermont Casting 20DVT - page 20

    Br ookh av e n Dir ect V ent Gas F ireplace 20 10009459 3. Open louvre assembly bottom. 4. Push in gas control knob slightly and turn clock- wise to “OFF”. Do not force. 5. Close control access panel. 1. STOP! Read the safety information above. 2. T urn off all electrical power to the fireplace. 3. For MN/MP/TN/TP appliances ONL Y , go on to S ...

  • Vermont Casting 20DVT - page 21

    10009459 21 Br ookh av e n Dir ect V ent Gas F ireplace NOTE: Before troubleshooting the gas control system, be sure external gas shut off is in the “On” position. SIT NOV A 820 MILLIVOL T V AL VE T roubleshooting the Gas Control System W ARNING: REMOVE GLASS FRONT BEFORE DOING ANY GAS CONTROL SERVICE WORK. SYMPTOM POSSIBLE CAUSES CORRECTIVE AC ...

  • Vermont Casting 20DVT - page 22

    Br ookh av e n Dir ect V ent Gas F ireplace 22 10009459 Fuel Conversion Instructions T o convert the 20DVT unit for use with a dif ferent gas follow these instructions. Before proceeding, turn control knob on valve to “ OFF ” and turn gas supply OFF . T urn OFF any electricity that may be going to the appliance. CAUTION: Logs may be HOT! Allow ...

  • Vermont Casting 20DVT - page 23

    10009459 23 Br ookh av e n Dir ect V ent Gas F ireplace CO106a DV360/580 Gas Conversion Pilot2 1/28/00 djt Fig. 42 Remove pilot orifice. CO106a Snap Ring Index T ab Allen Wrench CO105a DV360/580 Gas Conversion Pilot 1/28/00 djt Fig. 41 Remove pilot hood. CO105a Pilot Hood Pilot Bracket Pilot Orifice Conversion 1. Remove pilot hood by lifting up. ...

  • Vermont Casting 20DVT - page 24

    Br ookh av e n Dir ect V ent Gas F ireplace 24 10009459 Burner and Burner Compartment It is important to keep the burner and the burner compartment clean. At least once per year the logs and lava rock/ember material should be removed and the burner compartment vacuumed and wiped out. Remove and replace the logs as per the instructions in this manua ...

  • Vermont Casting 20DVT - page 25

    10009459 25 Br ookh av e n Dir ect V ent Gas F ireplace CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. 20DVT 1 1a 1b 2 3 4 5 7a,b 8a,b 12 13 9 14 10 16 17 18 20 21 22 24 9459 20DVT parts 5/06 19 15 Ref. Description 20DVT 1. Log Set (Co ...

  • Vermont Casting 20DVT - page 26

    Br ookh av e n Dir ect V ent Gas F ireplace 26 10009459 20DVT (continued) 7a. Orifice Pilot - Natural 10002268 7b. Orifice Pilot - Propane 10002269 8a. Pilot Assy . SIT - RN 10002264 8b. Pilot Assy . SIT - RP 10002265 9. Pilot T ubing w/Fittings SIT 10001296 10. Remote Switch Wire Assy . 20010345 1 1. Manifold T ubing w/Fittings (not shown) 57318 ...

  • Vermont Casting 20DVT - page 27

    10009459 27 Br ookh av e n Dir ect V ent Gas F ireplace Remote Controls Optional remote control units are available to control different functions of the appliance. Model Functions Controlled RC1 ON/OFF RC2 ON/OFF and T emperature IMTFK W all mounted thermostat control Ceramic Refractory Panels NOTE: The ceramic refractories are shipped separate fr ...

  • Vermont Casting 20DVT - page 28

    Br ookh av e n Dir ect V ent Gas F ireplace 28 10009459 ...

  • Vermont Casting 20DVT - page 29

    10009459 29 Br ookh av e n Dir ect V ent Gas F ireplace ...

  • Vermont Casting 20DVT - page 30

    Br ookh av e n Dir ect V ent Gas F ireplace 30 10009459 ...

  • Vermont Casting 20DVT - page 31

    10009459 31 Br ookh av e n Dir ect V ent Gas F ireplace BASIC W ARRANTY CFM Corporation (hereinafter referred to collectively as the Company) warrants that your new V ermont Castings or Majestic Gas Fireplace/ Stove is free from manufacturing and material defects for a period of one year from the date of purchase, subject to the following condition ...

  • Vermont Casting 20DVT - page 32

    Efficiency Ratings EnerGuide Ratings D.O.E. Model Fireplace Efficiency (%) Steady State (%) (AFUE%) 20DVTRN 60.1 80 64 20DVTRP 60.1 81 64 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 800-668-5323 • www .cfmcorp.com CFM Corporation ...

Manufacturer Vermont Casting Category Indoor Fireplace

Documents that we receive from a manufacturer of a Vermont Casting 20DVT can be divided into several groups. They are, among others:
- Vermont Casting technical drawings
- 20DVT manuals
- Vermont Casting product data sheets
- information booklets
- or energy labels Vermont Casting 20DVT
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vermont Casting 20DVT.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vermont Casting 20DVT, service manual, brief instructions and user manuals Vermont Casting 20DVT. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vermont Casting 20DVT.

Similar manuals

A complete manual for the device Vermont Casting 20DVT, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vermont Casting 20DVT by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vermont Casting 20DVT.

A complete Vermont Casting manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vermont Casting 20DVT - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vermont Casting 20DVT, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vermont Casting 20DVT, that we can find in the current document
3. Tips how to use the basic functions of the device Vermont Casting 20DVT - which should help us in our first steps of using Vermont Casting 20DVT
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vermont Casting 20DVT
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vermont Casting 20DVT in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vermont Casting 20DVT?

Use the form below

If you did not solve your problem by using a manual Vermont Casting 20DVT, ask a question using the form below. If a user had a similar problem with Vermont Casting 20DVT it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)