Manual Chamberlain 3255M 1/2 HP

36 pages 2.25 mb
Download

Go to site of 36

Summary
  • Chamberlain 3255M 1/2 HP - page 1

    The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.liftmaster.com GARAGE DOOR OPENER Models 3245M 1/3 HP 3255M 1/2 HP 3255-2M 1/2 HP For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The doo ...

  • Chamberlain 3255M 1/2 HP - page 2

    2 Introduction 2-5 Safety symbol and signal word review . . . . . . . . . . . . . . 2 Preparing your garage door . . . . . . . . . . . . . . . . . . . . . . . 3 Tools needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Carton inventory . ...

  • Chamberlain 3255M 1/2 HP - page 3

    3 To prevent damage to garage door and opener: • ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage. To prevent possible SERIOUS INJURY or DEATH: • ALWAYS call a trained door systems technician if garage door binds, sticks or is out of balance. An u ...

  • Chamberlain 3255M 1/2 HP - page 4

    4 Planning Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener. Safety Reversing Senso ...

  • Chamberlain 3255M 1/2 HP - page 5

    5 Your garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below. Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for installation is also listed below. Carton Inventory Straight Door Arm Section Cu ...

  • Chamberlain 3255M 1/2 HP - page 6

    6 ASSEMBLY STEP 1 Attach the Rail to the Motor Unit To avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the two washered bolts mounted in top of motor unit. • Position rail at a 45 ˚ angle to opener so one hole in rail and motor unit line up. • Thread one of the washered bolts part way in ...

  • Chamberlain 3255M 1/2 HP - page 7

    7 Lock Washer Inner Nut Trolley Chain Base of Rail 1/2" (13 mm) Outer Nut Mid Length of Rail To Tighten Outer Nut To Tighten Inner Nut INSTALLATION ASSEMBLY STEP 3 Tighten the Chain • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley. • To tighten the chain, turn outer nut in the direction shown (Fig ...

  • Chamberlain 3255M 1/2 HP - page 8

    8 INSTALLATION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door. 1. Close the door and mark the inside vertical centerline of the garage door. 2. Extend the line onto the header wall above the door. You can fasten the header bracket within 4 fe ...

  • Chamberlain 3255M 1/2 HP - page 9

    9 INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. DO NOT install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). WALL HEADER BR ...

  • Chamberlain 3255M 1/2 HP - page 10

    10 Clevis Pin 5/16"x2-3/4" Ring Fastener INSTALLATION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to allow ...

  • Chamberlain 3255M 1/2 HP - page 11

    11 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail. ? ...

  • Chamberlain 3255M 1/2 HP - page 12

    12 INSTALLATION STEP 5 Hang the Opener Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener. This bracket and fastening hardware are n ...

  • Chamberlain 3255M 1/2 HP - page 13

    13 LOCK LIGHT KG 1 3 9 7 5 KG 1 3 9 7 5 To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is NOT connected BEFORE installing door control. • Connect ONLY to 24 VOLT low voltage wires. To prevent possible SERIOUS INJURY or DEATH from a closing garage door: • Install door control within sight of garage door, out of ...

  • Chamberlain 3255M 1/2 HP - page 14

    14 INSTALLATION STEP 7 Install the Light • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install a 100 watt maximum light bulb in each socket. Light bulb size should be A19, standard neck only. The lights will turn ON and remain li ...

  • Chamberlain 3255M 1/2 HP - page 15

    15 INSTALLATION STEP 9 Electrical Requirements To avoid installation difficulties, do not run the opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn’t fit into the outlet you have, contact a ...

  • Chamberlain 3255M 1/2 HP - page 16

    16 Invisible Light Beam Protection Area Safety Reversing Sensor 6" (15 cm) max. above floor Safety Reversing Sensor 6" (15 cm) max. above floor Facing the door from inside the garage INSTALLATION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will m ...

  • Chamberlain 3255M 1/2 HP - page 17

    17 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Door Track FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) Indicator Light Lens Extension Bracket (See Accessories) Inside Garage Wall (Provided with Extension Bracket) (Provided with Extension Bracket) WALL MOUNT (RIGHT SIDE) Attach with Concrete Anchors (not provided) Inside Garage Wall L ...

  • Chamberlain 3255M 1/2 HP - page 18

    18 Invisible Light Beam Protection Area Safety Reversing Sensor Safety Reversing Sensor Connect Wire to Opener Quick-Connect Terminals Bell Wire Bell Wire Finished Ceiling 1. Strip wire 7/16" (11 mm) 2. Twist like colored wires together 7/16" (11 mm) Quick-Connect Terminals 3. To release or insert wire, push in tab with screwdriver tip Re ...

  • Chamberlain 3255M 1/2 HP - page 19

    19 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. INSTALLATION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace ...

  • Chamberlain 3255M 1/2 HP - page 20

    20 Header Wall Vertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing, or for the optional installation, use lag screws 5/16"x1-1/2" (Not Provided) to fasten door bracket. METAL DOOR Top of Door (Inside Garage) Door Bracket Optional ...

  • Chamberlain 3255M 1/2 HP - page 21

    21 INSTALLATION STEP 12 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONLY Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) ...

  • Chamberlain 3255M 1/2 HP - page 22

    22 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 5: IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm (Figure 5). • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to th ...

  • Chamberlain 3255M 1/2 HP - page 23

    23 ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. To operate the opener, press the Door Control push bar. Run the opener through a complete travel cycle. • Does the door open and close completely? • Does the door stay closed and not reverse ...

  • Chamberlain 3255M 1/2 HP - page 24

    24 ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door. If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weathe ...

  • Chamberlain 3255M 1/2 HP - page 25

    25 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Safety reversal system MUST be tested every month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, t ...

  • Chamberlain 3255M 1/2 HP - page 26

    26 OPERATION IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: Using Your Garage Door Opener Your Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Your opener will operate with up to eight Security ✚ ® ...

  • Chamberlain 3255M 1/2 HP - page 27

    27 To Open the Door Manually The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually. To reconnect the door to the opener, press the door control push bar. The lockout feature prevents the trolley from reconnecting automatically. Pull the emergency release handle down and back (toward the op ...

  • Chamberlain 3255M 1/2 HP - page 28

    28 CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re-adjustments, particularly during the first year of operation. Pages 23 and 24 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully. Repeat the safety reverse t ...

  • Chamberlain 3255M 1/2 HP - page 29

    29 HAVING A PROBLEM? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • Verify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Insta ...

  • Chamberlain 3255M 1/2 HP - page 30

    30 Bell Wire Safety Reversing Sensor Diagnostics Located On Motor Unit LED or Diagnostic LED "Learn" Button Installed Safety Reversing Sensor Your garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issue. Cons ...

  • Chamberlain 3255M 1/2 HP - page 31

    31 *3-Button Remotes If provided with your garage door opener, the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or compact remote can be programmed to operate other Security ✚ ® garage door openers. To Erase All Codes From Motor Unit Memory To deactivate any unwanted remote, first er ...

  • Chamberlain 3255M 1/2 HP - page 32

    32 1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the door control. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the door control (all three buttons are held). 4. Release butto ...

  • Chamberlain 3255M 1/2 HP - page 33

    33 1 3 4 5 6 2 REPAIR PARTS Rail Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A4813 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 1707LM One-piece rail 1708LM 8 ft. (2.4 m) complete rail 1710LM 10 ft. (3 m) complete rail 5 41D3484 Full chain assembly 6 83A11-2 Rail grease 7 UP CEILING M O UN T O N L Y 9 10 ...

  • Chamberlain 3255M 1/2 HP - page 34

    34 Motor Unit Assembly Parts 2 10 8 13 14 15 19 4 5 3 9 16 12 18 11 17 1 6 7 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear KEY PART NO. NO. DESCRIPTION 1 31D380 Sprocket cover 2 41C4220A Gear and sprocket assembly Complete with: Spring washer, thrust washer, retaining ring, bea ...

  • Chamberlain 3255M 1/2 HP - page 35

    35 ACCESSORIES CLOSED OPEN 374LM 370LM 395LM 41A5281 1702LM Outside Quick Release: Required for a garage with NO access door. Enables homeowner to open garage door manually from outside by disengaging trolley. Remote Light Control: Enables homeowner to turn on a lamp, television or other appliance from their car with their garage door opener remote ...

  • Chamberlain 3255M 1/2 HP - page 36

    © 2010, The Chamberlain Group, Inc. 114A3588B All Rights Reserved LIFTMASTER ® ONE-YEAR LIMITED WARRANTY FOUR YEAR MOTOR LIMITED WARRANTY The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally installed, that it is free from defect in materials and/o ...

Manufacturer Chamberlain Category Garage Door Opener

Documents that we receive from a manufacturer of a Chamberlain 3255M 1/2 HP can be divided into several groups. They are, among others:
- Chamberlain technical drawings
- 3255M 1/2 HP manuals
- Chamberlain product data sheets
- information booklets
- or energy labels Chamberlain 3255M 1/2 HP
All of them are important, but the most important information from the point of view of use of the device are in the user manual Chamberlain 3255M 1/2 HP.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Chamberlain 3255M 1/2 HP, service manual, brief instructions and user manuals Chamberlain 3255M 1/2 HP. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Chamberlain 3255M 1/2 HP.

Similar manuals

A complete manual for the device Chamberlain 3255M 1/2 HP, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Chamberlain 3255M 1/2 HP by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Chamberlain 3255M 1/2 HP.

A complete Chamberlain manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Chamberlain 3255M 1/2 HP - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Chamberlain 3255M 1/2 HP, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Chamberlain 3255M 1/2 HP, that we can find in the current document
3. Tips how to use the basic functions of the device Chamberlain 3255M 1/2 HP - which should help us in our first steps of using Chamberlain 3255M 1/2 HP
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Chamberlain 3255M 1/2 HP
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Chamberlain 3255M 1/2 HP in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Chamberlain 3255M 1/2 HP?

Use the form below

If you did not solve your problem by using a manual Chamberlain 3255M 1/2 HP, ask a question using the form below. If a user had a similar problem with Chamberlain 3255M 1/2 HP it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)