Manual Sony B2521E

65 pages 2.61 mb
Download

Go to site of 65

Summary
  • Sony B2521E - page 1

    OPERATION MANUAL Sony Desktop Robot GA CAST-AU4/B2521E ...

  • Sony B2521E - page 2

    CAST-AU4/B2521E This Operation Manual is intended as a guide for users of the Sony Desktop Robot ROBOKIDS. Before operating this system, you should first throughly read this manual. You may not understand all of the explanations the first time through, but be on the lookout for any special directions. It should be used in conjuction with the RK car ...

  • Sony B2521E - page 3

    CAST-AU4/B2521E First Time Users Read this manual form chapter 1 through chapter 4 before starting any operation. The manual describes the procedures required in setting up ROBOKIDS for users who have little experience with FA (Factory Automation) equipment. Routine Assembly Follow the respective application manuals for routine assembly task operat ...

  • Sony B2521E - page 4

    CAST-AU4/B2521E Manual Configuration This operation manual describes the procedures required to operate the desktop robot ROBOKIDS Various types of applications such as dispensing and soldering may be accomplished by exchanging the memory cards (RK card) which stores the programs required to run an application. The semi-programmable specification a ...

  • Sony B2521E - page 5

    CAST-AU4/B2521E Contents Safety Instruction ............................................................................................................. .. S-1 Unpacking ...................................................................................................................... ..... U-1 1. Outline 1-1 Nomenclature ...................... ...

  • Sony B2521E - page 6

    S-1 Safety Instruction CAST-AU4/B2521E Safety Instruction Sony Corporation designs and manufactures all its equipment with strict attention to safety. However, if the machine is operated or maintained without regard to the safety guidelines, damage or injury to the machine or operator may occur. To prevent accidents, those in charge of operation an ...

  • Sony B2521E - page 7

    S-2 CAST-AU4/B2521E Definition of warning symbols Pay particular attention to the following symbols and conventions shown on the machine and on the Operation Manual. Fully understand the contents of symbols and conventions before reading the Operation Manual. 《 Machine Symbols 》 Indicates a protective terminal of mechanical parts to which an ex ...

  • Sony B2521E - page 8

    S-3 Safety Instruction CAST-AU4/B2521E Caution ■ Important Safeguards ◆ The tool driving mechanism are subject to unexpected movement. Pay attention to safety measures. ◆ Turn off the main power prior to performing maintenance or inspections. Failure to observe this may result in severe injury through electric shocks or unexpected movement of ...

  • Sony B2521E - page 9

    S-4 CAST-AU4/B2521E Precautions on Usage Operate on the specified voltage Operate the ROBOKIDS only on AC power voltage as specified on the label of the machine. The power cord must be directly connected to the electrical output, and grounded. The ROBOKIDS conforms with the safety requirements of the target country to which it is shipped. When a ma ...

  • Sony B2521E - page 10

    S-5 Safety Instruction CAST-AU4/B2521E Precaution on memory cards Before inserting or removing a memory card, always turn the power off. The data stored in the memory card may be damaged if a memory card is inserted or removed while the power is on. Precaution on the teaching pendant ROBOKIDS uses a teaching pendant for the CAST-PRO or SRX. The CAS ...

  • Sony B2521E - page 11

    S-6 CAST-AU4/B2521E On handling batteries The following battery is used in the base machine controller. Lithium battery (primary battery) of type : CR17335SE-CN21 Manufactured by Sanyo Electric Co. Incorrect handling of the battery may result in dangerous situation. Do not perform the actions as listed below for safety. Sony Corporation is not resp ...

  • Sony B2521E - page 12

    U-1 Unpacking CAST-AU4/B2521E Unpacking Transport it to the installation position while taking care not to drop or fall. Pay extra attention not to give any vibration or shock because the controller contains precision electronic parts. Be sure to use the packaging material specified by Sony Corporation when transporting the machine. Caution NOTE Ac ...

  • Sony B2521E - page 13

    U-2 CAST-AU4/B2521E When the machine is unpacked, make sure the following items are in the package. Base machine Power cable Operation box USER I/O connector (For AC 200V to 240 V) PCR-E68FS (connector) PCS-E68LA (connector cover) (Honda Communications Company) Operation Manual External supply power connector for USER I/O MC 1.5/2-ST-3.81 (Phoenix ...

  • Sony B2521E - page 14

    1-1 1. Outline CAST-AU4/B2521E 1. Outline ROBOKIDS is a desktop assembly tool designed to automate cell production systems saving a significant amount of power consumed by assembly lines. It may be used in a variety of applications by simply exchanging the work unit and memory card. The basic operation procedures are common throughout the applicati ...

  • Sony B2521E - page 15

    1-2 CAST-AU4/B2521E 1-1 Nomenclature Front View * Debug station • • • Option Either the “ SRX teaching pendant ” or the program transfer cable can be directly connected to the debug station connector. * EJECT button • • • When inserting or removing the CAST-PRO teaching pendant, insert it or remove it while pressing the EJECT button ...

  • Sony B2521E - page 16

    1-3 1. Outline CAST-AU4/B2521E Rear View CAST-PRO Teaching Pendant SRX Teaching pendant CAST-P06 (option) SRX-P005/S (option) 8 8 8 POWER switch Internal/external selecting switch for I/O (Upper : OUTSIDE, Lower : INSIDE) INLET (power) USER INPUT/OUTPUT connector (External I/O connector) RS232C connector (Used only when the full open programmable s ...

  • Sony B2521E - page 17

    1-4 CAST-AU4/B2521E 1-2 Outline Drawings ■ ROBOKIDS Standard Type (CAST-AU4/B2521E) 320 (35) (69) 250 (Stroke) 105 40 105 (250) 203 (300) 18 A 2 48 (60) (6) 26 (40) 4 φ 4 4-M4 + 0.03 0 + 0.03 0 (7) A (52) 210 (Stroke) (4.5) 210 (360) 10 1 10 150 90 (6) (78) Detailed view of "A" ...

  • Sony B2521E - page 18

    1-5 1. Outline CAST-AU4/B2521E Height Adjustable Type (CAST-AU4/BT2521E) 320 (35) (69) 250 (Stroke) 105 40 105 (250) 203 (300) 18 A A (52) 210 (Stroke) (4.5) 210 10 11 0 90 (6) (78) (440) 230 ...

  • Sony B2521E - page 19

    1-6 CAST-AU4/B2521E ■ 3-Axes Model Z-unit ■ 4-Axes Model ZR-unit φ 12h7 5 280 50 T ool attachment position 63 162 97 45 144.5 5 30 57  45 58 11 5 76 26 97 162 68 10 (13) 179 (202) 70 48 14 26 4-M4 ...

  • Sony B2521E - page 20

    1-7 1. Outline CAST-AU4/B2521E Service Tapped-Hole Position 50 50 128 10 50 50 128 10 (120) 6-M3 10 10 (250) Side A 10 20 6-M3 (Side A only) (1.6) 4-φ 22 ...

  • Sony B2521E - page 21

    1-8 CAST-AU4/B2521E 4-φ 22 Service Tapped-Hole Position (Tall Model) ...

  • Sony B2521E - page 22

    1-9 1. Outline CAST-AU4/B2521E 1-3 Specifications 1-3-1 Machine Specifications Item X-axis Work envelope Y-axis Z-axis R-axis X-axis Maximum speeds Y-axis (*4) Z-axis R-axis X-axis Pose-repeatability Y-axis (positioning accuracy) Z-axis R-axis X-axis Maximum payload Y-axis Z-axis R-axis X-axis Resolution (*5) Y-axis Z-axis R-axis Robot mass (includ ...

  • Sony B2521E - page 23

    1-10 CAST-AU4/B2521E 1-3-2 Control Specifications Drive method Movement method Control axis count Interpolation function CP control speed Teaching method Program capacity Point data storage capacity Programming method General-purpose I/O Serial I/F Power supply voltage Power consumption Ground Pulse motor drive (open loop control) PTP, CP Up to fou ...

  • Sony B2521E - page 24

    2-1 2. Preparation CAST-AU4/B2521E 2. Preparation 2-1 Attaching the Units 2-1-1 Attaching the Z-unit 1. Fix the supplied mounting plate to the work table. (Two positions) Hexagon socket head cap screws M4 × 10, 2 pieces Tightening torque 15 kgfcm 2. Remove the Z-unit front cover. (The cover to which Sony logo mark is attached.) (Four positions) 3 ...

  • Sony B2521E - page 25

    2-2 CAST-AU4/B2521E 4. Attach the removed front cover. (Four positions) Tightening torque 8 kgfcm 5 . Connect the connectors to the Z-/ZR- unit connectors. Be sure to fix the connector by tightening the screws. 6. Attach the cable holder supplied, to the post. Hexagon socket head cap screws M3 × 6, 2 pieces Spring washer SW3, 2 pieces Flat washer ...

  • Sony B2521E - page 26

    2-3 2. Preparation CAST-AU4/B2521E 7. Fix the cable clamp of the cable to the cable holder. ...

  • Sony B2521E - page 27

    2-4 CAST-AU4/B2521E 2-1-2 Attaching the ZR-unit 1. Remove the front cover. (The cover to which Sony logo mark is attached.) (Six positions) 2. Fix the ZR-unit to the mounting plate. (Four positions) Determine the fixing position using the positioning pin that is supplied with the equipment. Hexagon socket head cap screw M4 × 6, 4 pieces Spring was ...

  • Sony B2521E - page 28

    2-5 2. Preparation CAST-AU4/B2521E 4 . Connect the connectors to the Z-/ZR- unit connectors. Be sure to fix the connector by tightening the screws. 5. Attach the cable holder supplied, to the post. Hexagon socket head cap screws M3 × 6, 2 pieces Spring washer SW3, 2 pieces Flat washer W3, 2 pieces Tightening torque 10 kgfcm Cable holder (supplied) ...

  • Sony B2521E - page 29

    2-6 CAST-AU4/B2521E 5. Fix the clamp of the cable on the cable holder. ...

  • Sony B2521E - page 30

    2-7 2. Preparation CAST-AU4/B2521E 2-2 Connecting the External Signal The base machine is equipped with the following connectors for external signal communication. • SAFETY (for external switch) connector (rear) • External S top (same function as the STOP button of the main unit) • Door, barrier • External return (same operation as the RETU ...

  • Sony B2521E - page 31

    2-8 CAST-AU4/B2521E Wiring diagram of connector for external switch (SAFETY) Applicable plug Type : DA-15PF-N (pin connector) Applicable shell Type : DA-C4-J10 ◆ An external stop button can be inserted between pins-14 and –15, or between pins-14 and –7. ◆ Be sure to use a shielded cable. The maximum length of a shielded cable is 1.5 m. The ...

  • Sony B2521E - page 32

    2-9 2. Preparation CAST-AU4/B2521E 2. Connect the external signals to the USERl I/O connector by soldering. Connect the wires to the corresponding pins of the USER I/O connector. For the signal names and pin numbers of the respective pins, refer to the I/O connector input/output specifications, Operation Manual (or Operation Manual of Full Open Pro ...

  • Sony B2521E - page 33

    2-10 CAST-AU4/B2521E ■ Input Circuit 24V 0V 0V IN 24V IN 680pF 470 Ω Maximum 7mA SI1 operates when SW1 is ON. Pin No. 1 35 2 36 3 37 4 51 18 52 19 53 SW1 SW30 Direction of current S1 I 1 I 2 I 3 I 4 I 5 I 21 I 22 COM1 0V SI1 (SYSRUN) SI3 SI2 SI8 ( Reservation ) input ( Reservation ) input ( Reservation ) input 3.3k Ω TLP280 3.3k Ω 3.3k Ω ...

  • Sony B2521E - page 34

    2-11 2. Preparation CAST-AU4/B2521E ■ Output Circuit ◆ Add the diodes as shown when relay coils are connected as the load. ◆ Be careful that the thermistor operates to shut down the +24 V power supply when 24 V output is used and the current of 1 A or more flows. Modify the external circuit to reduce the current capacity to 1 A or less. Therm ...

  • Sony B2521E - page 35

    2-12 CAST-AU4/B2521E 2-3 Connecting to an Electrical Outlet Prepare the power cable for AC 200 V to 240 V referring to the following connection diagram. The user must provide and wire an AC power plug to connect to the AC outlet. Brown Blue Green/Yellow L N Earth Plug end Power cable end Connection diagram of the AC power cable for 200 V to 240 V T ...

  • Sony B2521E - page 36

    2-13 2. Preparation CAST-AU4/B2521E 2-4 Starting Up the Base Machine Make sure that the main power is turned off. Connect the operation box. 2-4-1 Full-open Programmable Specification Turn on the power switch on the rear panel. Subsequent operating procedure changes depending on the application created by user. 2-4-2 When Using Memory Card “RK ca ...

  • Sony B2521E - page 37

    2-14 CAST-AU4/B2521E 3. Turn the base machine on. About five seconds later, the white indicator of START button starts flashing in green. 4. Press the START button. The machine starts returning home. The green indicator of the START button turns on and changes to slow flashing after completing home return. (About 30 seconds later) 5. Press the STAR ...

  • Sony B2521E - page 38

    3-1 3. Maintenance CAST-AU4/B2521E 3. Maintenance 3-1 Maintaining the Machine Clean the surfaces of the machine with a soft dry cloth. If the stain is difficult to remove, use cloth moistened with a mild detergent solution, followed by using a dry cloth. Do not use volatile solvents such as alcohol, benzene or thinner, as they may mar the finish. C ...

  • Sony B2521E - page 39

    3-2 CAST-AU4/B2521E 3. Move the work table and the work unit to the ends by hand, remove the X-axis and Y-axis covers by pulling them, then remove the fallen materials such as screws. Remove the front cover of the Z-unit and ZR- unit also. If the work table and the work unit are not moved to the ends as indicated, they may cause damage to the cover ...

  • Sony B2521E - page 40

    3-3 3. Maintenance CAST-AU4/B2521E 6. Apply grease to the Z unit and the ZR unit as shown in the same manner. 7. Attach the covers of the X-axis, Y-axis, Z unit and ZR unit to their original positions. ◆ Be careful not to damage the covers when they are reinstalled. ◆ After the covers are attached, move the respective axes using the teaching pe ...

  • Sony B2521E - page 41

    3-4 CAST-AU4/B2521E 3-3 Cleaning and Replacing the Air Filter Air is circulated in the controller of the base machine to cool the controller. The cooling air is introduced through the air filter on the rear of the machine. Dust may be accumulated choking the air filter which decreases the cooling power causing serious damage such as thermal breakdo ...

  • Sony B2521E - page 42

    3-5 3. Maintenance CAST-AU4/B2521E 3. Replace the media (filter). 4. Reinstall the front cover as before. Replacement media Sony Order No. ......... 4-761-607-01 ...

  • Sony B2521E - page 43

    3-6 CAST-AU4/B2521E NOTE 3-4 Replacing the Battery 1. Turn off the POWER switch and unplug the AC power cord from the AC outlet. The battery is located in the recess at the bottom on the rear of the Z-axis. 2 . Exchange the battery with the new lithium battery. Battery replacement must be completed within eight hours after the main power is turned ...

  • Sony B2521E - page 44

    4-1 4. Troubleshooting CAST-AU4/B2521E 4. Troubleshooting 4-1 Common Items 4-1-1 Stepping Out (Note 1) The machine performs open loop servo control using a pulse motor (stepping motor) without positional feedback. The machine thus continues to operate with positional error even if it steps out due to overloading of the retaining torque of the motor ...

  • Sony B2521E - page 45

    4-2 CAST-AU4/B2521E (4) Synthesis of movements in the same direction In some programs, the machine is operated by synthesizing two movements (the FOS and PFOS with the AWAKE instruction of LUNA). When the teaching points to be synthesized are aligned on the same line, the machine can step out. When such a movement is experienced, the application pr ...

  • Sony B2521E - page 46

    4-3 4. Troubleshooting CAST-AU4/B2521E 4-1-2 External Noise External electrical noise is a difficult problem because it is invisible. Take the following remedial measures. If the symptom disappears, electrical noise was probably the cause of the trouble. (1) Earthing the power supply Always connect the earth of the AC output to ground (Class 3 grou ...

  • Sony B2521E - page 47

    4-4 CAST-AU4/B2521E 4-2 Full-open Programmable Specifications Connect the SRX teaching pendant via a debug station and check the error codes and error history using the following procedure. 1 Connect a debug station. 2 Connect the SRX teaching pendant. 3 Press the MANAGEMENT key and select “Error History” with the F4 key by scrolling the cursor ...

  • Sony B2521E - page 48

    4-5 4. Troubleshooting CAST-AU4/B2521E 5 Check the error code number E*** on display and find out causes and countermeasures referring to the following table. When the machine does not operate normally, check the error contents referring to the following table. For the contents that are unique to the respective applications, refer to the Operation ...

  • Sony B2521E - page 49

    4-6 CAST-AU4/B2521E Error No. E301 E302 E303 E304 E314 E315 E316 E317 Causes X-axis limit sensor error Y-axis limit sensor error Z-axis limit sensor error R-axis limit sensor error X-axis command position error Y-axis command position error Z-axis command position error R-axis command position error Solutions Correct the speed so as not to exceed t ...

  • Sony B2521E - page 50

    4-7 4. Troubleshooting CAST-AU4/B2521E 4-3 When Memory Card (RK Card) is Used The operational flow starting from turning on the main power of the machine until the programmed operation or teaching is started, is shown as follows. Causes and countermeasures when trouble occurs in the respective state from 1) to 9) are shown on the next page. Use the ...

  • Sony B2521E - page 51

    4-8 CAST-AU4/B2521E Solutions Start operation from the very beginning Confirm the sensor cable connection Correct the controller data from TP of the SRX Symptoms “ E07 ” appears on display Machine movement does not stop (It moves in the reverse direction.) Causes Returning home failed Sensor cable is defective Controller data is abnormal Fault- ...

  • Sony B2521E - page 52

    4-9 4. Troubleshooting CAST-AU4/B2521E Fault-Finding Chart of 5) Fault-Finding Chart of 6) or 7) or 8) Solutions Turn on the main power of the machine system and start operation from the very beginning Turn on the main power of the machine system and start operation from the very beginning Symptoms “ E08 ” appears on display “ E09 ” appears ...

  • Sony B2521E - page 53

    4-10 CAST-AU4/B2521E If a trouble occurs, check the following items before contacting your Sony dealer or the nearest Sony FA offices. 1) Name of dealer from which you purchased the ROBOKIDS Company name : Person in charge : Tel: 2) What is the serial number of your ROBOKIDS? (It is marked on the sticker of the rear cover.) M No. R No. 3) What type ...

  • Sony B2521E - page 54

    5-1 5. Repair Parts Lists CAST-AU4/B2521E 5. Repair Parts Lists 5-1 ROBOKIDS Body 5-2 Z-axis Unit Descriptions TASK board BASE board Battery DC switching power supply ZWS30-5/J DC switching power supply ZWS150PF-24/J Circuit protector Fan harness Self-illuminating stop switch Self-illuminating stop switch Digital switch X-axis motor Y-axis motor X- ...

  • Sony B2521E - page 55

    5-2 CAST-AU4/B2521E 5-3 Z/R-axis Unit Descriptions Z-axis motor R-axis motor Z-axis home position sensor harness R-axis home position sensor harness Spline ball screw Z-axis timing belt R-axis timing belt Z/R-axis relay cable harness Bearing Mechanism block assembly Part No. 1-763-187-11 1-763-187-11 1-959-101-11 1-959-097-12 4-760-605-01 4-760-645 ...

  • Sony B2521E - page 56

    6-1 6. Appendix CAST-AU4/B2521E 6. Appendix ■ User Input/Output Specifications of USER I/O Connector Input Connector pin No. 3 37 4 38 5 39 6 40 7 41 8 42 9 43 10 44 11 45 12 46 13 47 14 48 15 49 16 50 17 51 I/O names in terms of software SI1 SI2 SI3 SI4 SI5 SI6 SI7 SI8 I1 I2 I3 I4 I5 I6 I7 I8 I9 I10 I11 I12 I13 I14 I15 I16 117 I18 I19 I20 I21 I2 ...

  • Sony B2521E - page 57

    6-2 CAST-AU4/B2521E Output Connector pin No. 20 54 21 55 22 56 23 57 24 58 25 59 26 60 27 61 28 62 29 63 30 64 31 65 32 66 33 67 34 68 I/O names in terms of software SO1 SO2 SO3 SO4 SO5 SO6 SO7 SO8 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13 L14 L15 L16 L17 L18 L19 L20 L21 L22 Contents RK card specification (including semi-programmable specification ...

  • Sony B2521E - page 58

    6-3 6. Appendix CAST-AU4/B2521E ■ Specifications of the Connected I/O (Used only in the semi-programmable specifications and the full open programmable specifications) Input Output ■ User external power supply connector Contents START button (White button of operation box) RETURN button (To be connected from the rear SAFETY connector by user) W ...

  • Sony B2521E - page 59

    6-4 CAST-AU4/B2521E ■ Connector for Debug Station Type : DBLC-J25SAF-10L9 Manufacturer : JAE Applicable plug : DBSP-JB25PF Manufacturer : JAE Applicable shell : DB-C8-J10-F4-1 Manufacturer : JAE Signal FG TP-RXD TP-TXD TP-CTS TP-RTS TP-DTR C GND SIO-DSR SIO-RXD C GND NC C GND SIO-CTS NC SIO-RTS EXS5 EXS2 /TP CN1 NC TP-DSR SIO-TXD PC05V SIO-DTR C ...

  • Sony B2521E - page 60

    6-5 6. Appendix CAST-AU4/B2521E ■ Connector for Operation Box Type : 17HE-13150-73 Manufacturer : DDK Applicable plug : 17HE-23150-CD8A Manufacturer : DDK Applicable shell : 17H-7PCR-102 Manufacturer : DDK Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Contents Work program No. 1 (First digit of the PROGRAM switch (1)) START LED S top LED 0 V Applic ...

  • Sony B2521E - page 61

    6-6 CAST-AU4/B2521E ■ SAFETY Connector Type : DA-J15PF1L9 Manufacturer : JAE Applicable plug : DA-15PF-N Manufacturer : JAE Applicable shell : DA-C4-J10 Manufacturer : JAE Signal 24V SA START OUT SA STOP OUT STOP RELAY OUT (C) STOP RELAY OUT (NO) STOP RELAY OUT (NC) 0V FG SA RETURN IN SA Stop IN (C) SA Stop IN (NC) BAR (C) BAR (NC) Stop BAR RELEA ...

  • Sony B2521E - page 62

    6-7 6. Appendix CAST-AU4/B2521E ■ Connector for ZR-axis Cable Model : DBLC-J25SAF-10L9 Manufacturer : JAE Applicable plug : DB-25PF-IN Manufacturer : JAE Applicable shell : DB-C4-J11 Manufacturer : JAE Signal FG ZR_COM Z_DET ZR_DET Z_24V Z_LIM Z_GND Z_A Z_B_C Z_/B R_A R_B_C R_/B BRK+ BRK– R24V R_LIM R_GND FG Z_A_C Z_/A Z_B R_A_C R_/A R_B Pin No ...

  • Sony B2521E - page 63

    Supply Period of Repair Parts The functional repair parts (parts needed to maintain product performance) of this machine will be supplied for up to seven years in principle after production is discontinued. Because it may be possible to repair the machines depending upon the location of the problem even after this period, consult the service or sal ...

  • Sony B2521E - page 64

    1st Edition November, 1998 3rd Edition October, 2001 ...

  • Sony B2521E - page 65

    Printed in Japan © 2001.10 3-864-81 1-13 Sony Manufacturing Systems Corporation ...

Manufacturer Sony Category Robotics

Documents that we receive from a manufacturer of a Sony B2521E can be divided into several groups. They are, among others:
- Sony technical drawings
- B2521E manuals
- Sony product data sheets
- information booklets
- or energy labels Sony B2521E
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sony B2521E.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sony B2521E, service manual, brief instructions and user manuals Sony B2521E. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sony B2521E.

Similar manuals

A complete manual for the device Sony B2521E, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sony B2521E by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sony B2521E.

A complete Sony manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sony B2521E - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sony B2521E, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sony B2521E, that we can find in the current document
3. Tips how to use the basic functions of the device Sony B2521E - which should help us in our first steps of using Sony B2521E
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sony B2521E
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sony B2521E in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sony B2521E?

Use the form below

If you did not solve your problem by using a manual Sony B2521E, ask a question using the form below. If a user had a similar problem with Sony B2521E it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)