Manual Cisco Systems 2500 Series

12 pages 0.14 mb
Download

Go to site of 12

Summary
  • Cisco Systems 2500 Series - page 1

    1 Doc. No . Cisco Systems, Inc. All rights reser ved. 170 West Tasman Drive San Jose, CA 95134-1706 USA Cisco Systems, Inc. Corporate Headquarters Copyright © 1997 Installing Cisco A C and DC P o wer Supplies in Cisco 2500 Ser ies Routers Product Number s: PWR-2500-AC=, PWR-2500-DC= This document describes how to replace the A C or DC po wer suppl ...

  • Cisco Systems 2500 Series - page 2

    2 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Series Routers Required T ools and Equipment W arning Read the installation instructions before you connect the system to its power source. (T o see translated versions of this warning, refer to the Re gulatory Compliance and Safety Information document that accompanied the router .) Requi ...

  • Cisco Systems 2500 Series - page 3

    Installing Cisco AC and DC Power Supplies in Cisco 2500 Series Routers 3 Removing AC and DC Power Supplies W arning Do not touch the power supply when the power cord is connected. F or systems with a power switch, line v oltages are present within the po wer supply ev en when the power switch is OFF and the po wer cord is connected. For systems wit ...

  • Cisco Systems 2500 Series - page 4

    4 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Ser ies Routers Removing A C and DC P ower Supplies Figure 2 Removing the Scre w Step 2 Disconnect the po wer connector from the system board. (See Figure 3.) Grasp the sides of the power connector and pull upw ard while rocking the connector side to side. Caution Do not pull on the connec ...

  • Cisco Systems 2500 Series - page 5

    Installing Cisco AC and DC Power Supplies in Cisco 2500 Series Routers 5 Installing AC and DC Power Supplies Figure 4 Removing the P ower Supply Step 4 Place the remov ed screw and po wer supply in an antistatic bag. Installing A C and DC P ower Supplies This section describes how to install A C and DC po wer supplies. Although an A C power supply ...

  • Cisco Systems 2500 Series - page 6

    6 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Ser ies Routers Replacing the Cover Figure 6 Installing the Screw Step 3 Connect the po wer connector from the system board. Grasp the sides of the power connector and gently push downw ard while rocking the connector side to side. (See Figure 7.) Figure 7 Connecting the P ower Connector R ...

  • Cisco Systems 2500 Series - page 7

    Installing Cisco AC and DC Power Supplies in Cisco 2500 Series Routers 7 Replacing the Cover Caution T o fit the two sections together , it may be necessary to work them together at one end and then the other , w orking back and forth; ho wever , use care to pre v ent bending the chassis edges. (T o see translated versions of this warning, refer t ...

  • Cisco Systems 2500 Series - page 8

    8 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Ser ies Routers Connecting the DC P ower Supply Connecting the DC P o wer Supply This section describes the DC power supply specifications and wiring. W arning This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by ...

  • Cisco Systems 2500 Series - page 9

    Installing Cisco AC and DC Power Supplies in Cisco 2500 Series Routers 9 Connecting the DC Power Supply Figure 9 DC P ower Supply Connections W arning When stranded wiring is required, use approved wiring terminations, such as closed-loop or spade-type with upturned lugs. These terminations should be the appropriate size for the wires and should cl ...

  • Cisco Systems 2500 Series - page 10

    10 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Ser ies Routers Connecting the DC P ower Supply W arning This product relies on the building’ s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 V A C, 15A U.S. (240 V A C, 10A international) is used on the phase conductor ...

  • Cisco Systems 2500 Series - page 11

    Installing Cisco AC and DC Power Supplies in Cisco 2500 Series Routers 11 Obtaining Service and Support Figure 11 Rear Panel Label Locations Note The System Identifier label shown in Figure 11 shows the Cisco 2520 DC system label for demonstration purposes. Place the appropriate label for your specific model of Cisco 2500 series router in place o ...

  • Cisco Systems 2500 Series - page 12

    12 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Ser ies Routers Cisco Connection Online A v ailable 24 hours a day , 7 days a week, CCO provides a wealth of standard and value-added services to Cisco’ s customers and business partners. CCO services include product information, product documentation, software updates, release notes, t ...

Manufacturer Cisco Systems Category Network Router

Documents that we receive from a manufacturer of a Cisco Systems 2500 Series can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- 2500 Series manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems 2500 Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems 2500 Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems 2500 Series, service manual, brief instructions and user manuals Cisco Systems 2500 Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems 2500 Series.

A complete manual for the device Cisco Systems 2500 Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems 2500 Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems 2500 Series.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems 2500 Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems 2500 Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems 2500 Series, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems 2500 Series - which should help us in our first steps of using Cisco Systems 2500 Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems 2500 Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems 2500 Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems 2500 Series?

Use the form below

If you did not solve your problem by using a manual Cisco Systems 2500 Series, ask a question using the form below. If a user had a similar problem with Cisco Systems 2500 Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)