Manual Delta 22-451

24 pages 2.5 mb
Download

Go to site of 24

Summary
  • Delta 22-451 - page 1

    INSTRUCTION MANUAL DC-580 20" Planer (Model 22-450, Thr ee Phase) (Model 22-451, Single Phase) P ART NO. 1349960 - 06-02-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-80 ...

  • Delta 22-451 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • Delta 22-451 - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta 22-451 - page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL WARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...

  • Delta 22-451 - page 5

    ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury . 2. OBT AIN ADVICE from your supervisor , instructor , or another qual ...

  • Delta 22-451 - page 6

    6 6 FOREWORD FUNCTIONAL DESCRIPTION NOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRA TES THE CURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRA TIONS CONT AINED IN THE MANUAL ARE REPRESENT A TIVE ONL Y AND MA Y NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND ARE INTENDED TO ILLUSTRA TE TECHNIQUE ONL Y . The Delta Indusrial Model 22-450 (DC-580) 20 ...

  • Delta 22-451 - page 7

    7 7 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfac ...

  • Delta 22-451 - page 8

    8 Fig. 4 Fig. 5 Fig. 6 UNP ACKING AND CLEANING Remove the bolts that fasten the machine to the shipping skid. T wo lifting lugs are built into the machine, one of which is shown at (E) Fig. 3. These lugs can be used to mechanically lift the machine using a forklift and lifting straps. NOTE: The other lifting lug is located at the rear and the oppos ...

  • Delta 22-451 - page 9

    9 ASSEMBLING CUTTERHEAD GUARD Position cutterhead guard (A) Fig. 7, on top cover of machine. Align holes in cutterhead guard (A) Fig. 7, with holes in top cover and fasten with six M6x12mm button head screws (B), five of which ar e shown. Fig. 7 ASSEMBLING DUST HOOD A dust hood with a 5" opening is supplied with your machine and is to be used ...

  • Delta 22-451 - page 10

    10 T o br ing power to this machine: Loosen screw (A) Fig. 10, and remove co ver (B) from terminal box located at the rear of the machine. Bring the power line up through the hole (C) Fig. 11, in ter minal bo x. NO TE: Strain relief and pow er cord clamp are not supplied with the machine. Remov e plastic shield (D) Fig. 11, from ter minal strip (E) ...

  • Delta 22-451 - page 11

    11 Fig. 13 Fig. 14 RAISING AND LOWERING T ABLE Adjust the table height by loosening lock knob (A) Fig. 15, and rotating table adjusting handwheel (B). T o raise the table, turn handwheel (B) clockwise; to lower the table, turn handwheel (B) counterclockwise. Tighten lock knob (A) Fig. 15, after table height adjustment is made. The English/Metric ta ...

  • Delta 22-451 - page 12

    12 Fig. 17 Fig. 16 Fig. 19 Fig. 20 Fig. 18 FEED ROLLER SPEEDS Y our planer is equipped with feed roller speeds of 20 and 30 feet per minute depending on belt placement on the pulleys. As a rule, a faster feed rate is used for general planing operations, while a slower feed rate (because it provides mor e cuts per inch of stock) gives a finer and sm ...

  • Delta 22-451 - page 13

    13 T ABLE ROLLERS Y our planer is supplied with two table rollers (A) Fig. 21, which aid in feeding the stock by reducing friction be- tween the stock and the table and rotate as the stock is fed through the planer . 1. T o raise the table rollers, loosen locking lever (B) Fig. 21, and pull control lever (C) upward to the desir ed height setting. 2 ...

  • Delta 22-451 - page 14

    14 Fig. 25 6. T o check the height of the outfeed table roller , proceed as follows: with a feeler gage (B) Fig. 25, measure the gap between the table surface and the straight edge (A) near the outfeed roller (F). Fig. 26 7. If an adjustment to the outfeed table r oller is necessary , loosen locknut (G) Fig. 26, which is located under the table and ...

  • Delta 22-451 - page 15

    15 CHECKING AND ADJUSTING DRIVE BEL T TENSION Proper belt tension is when ther e is approximately 1/4" deflection, using light finger pr essure on the drive belts (A) Fig. 28, midway between pulleys. If an adjustment is necessary , proceed as follows: Fig. 28 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Disengage feed roller lever (B) Fig. 28. ...

  • Delta 22-451 - page 16

    16 Fig. 30 CHECKING AND ADJUSTING FEED ROLLER BEL T TENSION Proper tension on the feed r oller belt is obtained when there is appr oximately 1/2" deflection, using light finger pressur e on feed roller belt (A) Fig. 30. midway between pulleys (B) and (C), with feed roller lever (D) engaged. If an adjustment is necessary , proceed as follows: 1 ...

  • Delta 22-451 - page 17

    Fig. 33 Fig. 34 Fig. 35 CHECKING, RESETTING AND REPLACING KNIVES When checking, resetting and r eplacing knives, proceed as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove locking screw (E) Fig. 4, and raise top cover (A) Fig. 33, to expose cutterhead (B). 3. Carefully place knife setting gage (C) Figs. 34 and 35, so the gage is positio ...

  • Delta 22-451 - page 18

    18 Fig. 36 Fig. 37 Fig. 38 Fig. 39 CONSTRUCTING GAGE BLOCK In order to check and adjust the height of the chipbr eaker , pressur e bar , infeed and outfeed rollers and adjust the cutter -head parallel to the table, you will need a gage block made of hard wood. The gage block can be constructed by following the dimensions shown in Fig. 36. ADJUSTING ...

  • Delta 22-451 - page 19

    19 Fig. 40 Fig. 41 Fig. 42 Fig. 43 ADJUSTING PRESSURE BAR The pressur e bar is located directly behind the cutterhead and rides on the planed surface of the stock, pressing the stock downward on the table. The pr essure bar must be parallel to the knives and tangent to the table and set .010" below the cutting circle. T o check and adjust the ...

  • Delta 22-451 - page 20

    20 4. Place gage block (A) Fig. 44, under outfeed roller (D). The bottom of roller (D) should just touch gage block (A). 5. If an adjustment is necessary , loosen locknut (E) Fig. 45, and turn adjustment screw (F) until the outfeed roller just touches the top of gage block (A) Fig. 44. 6. Repeat the adjustment on the opposite end of the outfeed rol ...

  • Delta 22-451 - page 21

    21 Fig. 49 Fig. 50 Fig. 51 Fig. 53 Fig. 52 LEVELING THE T ABLE The table is set parallel to the cutterhead at the factory and no further adjustment should be necessary . T o check if the table is level with the cutterhead, proceed as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE . 2. Check to see if the cutterhead knives are set correctly as exp ...

  • Delta 22-451 - page 22

    22 ADJUSTING T ABLE GIBS In the unlikely event of the table developing unwanted movement during planing operations, the table can be checked and adjusted as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. With the table in the locked position, and with a feeler gage, measure the gap between table gib (A) Fig. 54 and table bracket (B). When set ...

  • Delta 22-451 - page 23

    23 Fig. 55 B A LUBRICA TING WORK SURF ACES Apply household floor paste wax to the machine table and extension table or other work surface weekly . LUBRICA TING THE FEED ROLLERS The machine’ s feed rollers must be lubricated about every 50 to 100 hours of use or as needed. T o lubricate the machine’ s feed rollers, add a few drops of 10W Machine ...

  • Delta 22-451 - page 24

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Manufacturer Delta Category Planer

Documents that we receive from a manufacturer of a Delta 22-451 can be divided into several groups. They are, among others:
- Delta technical drawings
- 22-451 manuals
- Delta product data sheets
- information booklets
- or energy labels Delta 22-451
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta 22-451.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta 22-451, service manual, brief instructions and user manuals Delta 22-451. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta 22-451.

Similar manuals

A complete manual for the device Delta 22-451, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta 22-451 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta 22-451.

A complete Delta manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta 22-451 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta 22-451, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta 22-451, that we can find in the current document
3. Tips how to use the basic functions of the device Delta 22-451 - which should help us in our first steps of using Delta 22-451
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta 22-451
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta 22-451 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta 22-451?

Use the form below

If you did not solve your problem by using a manual Delta 22-451, ask a question using the form below. If a user had a similar problem with Delta 22-451 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)