English dropdown-ico

Manual Hearth and Home Technologies PALOMA-BL

62 pages 3.82 mb
Download

Go to site of 62

Summary
  • Hearth and Home Technologies PALOMA-BL - page 1

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 1 Model(s): P ALOMA-BL P ALOMA-BZ P ALOMA-GR P ALOMA-GY • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light any appliance. - Do not touch any electrical switch. Do not ...

  • Hearth and Home Technologies PALOMA-BL - page 2

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 2 APPROVED FOR CANADA AND USA TO: ANSI Z21.88b -2003 / CSA 2.33b -2003 Vented Gas Fireplace Heate r, and applicable sections of UL307b Gas Burn ing Heating Appliances f or Manufactured Homes and Recreational Vehicles, CAN/CG A 2.17-M91 “Gas Fired Appliances for us e at Hig h Alti tude s.” ...

  • Hearth and Home Technologies PALOMA-BL - page 3

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 3 T able of Contents 1 Listing and Code Approvals A. Appliance Certi fi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Glass Speci fi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. BTU Speci fi cations . . . . . . . . . . . . . . . . . . . . . ...

  • Hearth and Home Technologies PALOMA-BL - page 4

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 4 Manufactured Home or Mobile Home installation may occur only after the home is site located and must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable, the Standard for Manufactured Home Installations, AN ...

  • Hearth and Home Technologies PALOMA-BL - page 5

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 5 H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wal ...

  • Hearth and Home Technologies PALOMA-BL - page 6

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 6 A. Design and Installation Considerations Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. 2 2 Get ting Star ted C. Ins ...

  • Hearth and Home Technologies PALOMA-BL - page 7

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 7 B. Clearances to Combustibles Model A B C D E F G H I J K Paloma Inches 6 10-1/8 12-1/8 54 36 30-3/4 13-1/4 13-1/4 1 15-1/2 5 Millimeters 152 257 308 1372 914 781 337 337 25 394 127 3 3 F raming and Clearances Note: • Illustrations reflect typical installations and are FOR DESIGN PURPOSES ...

  • Hearth and Home Technologies PALOMA-BL - page 8

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 8 C. Optional Stone Surround Installed D C A B F G G E A Figure 3.1 Model A B C D E F G Paloma Surround Inches 3-1/4 4 30-3/4 36 1 20* 4-3/4 Millimeters 83 102 781 914 25 508 121 *Distance is measured from fl ue collar to corner Note: Flooring beneath appliance may reach 90 degrees plus room ...

  • Hearth and Home Technologies PALOMA-BL - page 9

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 9 A. V ent T ermination Minimum Clearances Fire Risk. Explosion Risk. Maintain vent clearance to combustibles as speci fi ed. • Do not pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause fi re. Figure 4.1 4 4 T er ...

  • Hearth and Home Technologies PALOMA-BL - page 10

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 10 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 4.4 Minimum Clearances for T ermination A = 12 inches................. clearances above grade, veranda, porch, deck or balcony B = 12 inches................. clearances to window or door that may be opene ...

  • Hearth and Home Technologies PALOMA-BL - page 11

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 1 1 Fire Hazard. Explosion Risk. Asphyxiation Risk. Do NOT connect this gas appliance to a chimney fl ue serving a separate solid-fuel or gas burning appliance. • V ent this appliance directly outside. • Use separate vent system for this appliance. May impair safe operation of this appli ...

  • Hearth and Home Technologies PALOMA-BL - page 12

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 12 EX. 2 EX. 1 2' 4' 6' 8' 10' 12' 14' 15' 30' 28' 26' 24' 22' 20' 18' 16' 14' 12' 10' 8' 6' 4' 2' 0' (MAX) (MIN) 32' 34' 35' 1 1-5/8” 3 ft. (914 mm) Maximu ...

  • Hearth and Home Technologies PALOMA-BL - page 13

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 13 Figure 5.3 Figure 5.4 4. For installations using a round support box/wall thimble (check pipe manufacturer's instructions), mark the wall for a 10 in. x 10 in. (254 mm x 254 mm) square hole. The center of the square hole should line up with the center line of the horizontal pipe, as s ...

  • Hearth and Home Technologies PALOMA-BL - page 14

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 14 8 in. (203 mm) 7 in. (178 mm) 7 in. (178 mm) 6 in. (152 mm) 5. Installation requires a minimum of 6 in. (152 mm) horizontal run of vent with a 1/4 in. (6 mm) rise run towards the termination. Each 1 ft. (305 mm) of horizontal venting must include a 1/4 in. (6 mm) rise. Never allow the vent ...

  • Hearth and Home Technologies PALOMA-BL - page 15

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 15 1 1 . Place the wall thimble cover over the pipe assembly and slide the appliance and vent assembly towards the wall, carefully inserting the vent pipe into the vent termination cap assembly . It is important that the vent pipe extend into the vent termination cap a sufficient distance so ...

  • Hearth and Home Technologies PALOMA-BL - page 16

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 16 40 ft. (12 m) MAXIMUM Figure 5.10 VERTICAL TERMINA TION CAP USE P ART #SLK-991DA STORM COLLAR FLASHING FIRESTOP PIPE LENGTH SUPPORT BOX On vertical terminations use only Part #SLK-991DA or like components. See page 55. Figure 5.1 1 1. Check the installation instructions for required 1 in. ...

  • Hearth and Home Technologies PALOMA-BL - page 17

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 17 4. Assemble the desired lengths of pipe and elbows necessary to reach from the appliance up through the round support box. Ensure that all pipe and elbow connections are in their fully twist-locked position. Assemble as instructed. 5. Cut a hole in the roof centered on the small drill hole ...

  • Hearth and Home Technologies PALOMA-BL - page 18

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 18 CEILING FIRESTOP NAILS MINIMUM 1 in. (25 mm) CLEARANCE MINIMUM 1 in.(25 mm) CLEARANCE MINIMUM 1 in.(25 mm) CLEARANCE MINIMUM 1 in.(25 mm) CLEARANCE Figure 5.16 9. Twist-lock the vent cap and seal. Note: For multi-story vertical installations, a ceiling firestop is required at the second fl ...

  • Hearth and Home Technologies PALOMA-BL - page 19

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 19 H. Cathedral Ceiling 1. Follow installation Steps 1 and 2 under vertical instal- lation section, page 16. 2. Remove shingles or other roof covering as necessary to cut the rectangular hole for the support box. Cut the hole 1/8 in. (3 mm) larger than the support box outline. 3. Lower the su ...

  • Hearth and Home Technologies PALOMA-BL - page 20

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 20 I. Class A Metal Chimney Figure 5.20 Figure 5.22 Figure 5.23 4. Pass the flex pipe down through the center of the chimney system, and center the top adapter on the top of the chimney pipe. Drill four 1/8 in. (3 mm) diameter holes through the top adapter , and into the chimney top. Ensure t ...

  • Hearth and Home Technologies PALOMA-BL - page 21

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 21 J. Existing Masonry Chimney TERMINA TION CAP P ART #SLK-991DA FLASHING 4 in. (102 mm) FLEX LINER TOP ADAPTER RETRO CONNECTOR 90º ELBOW DIRECT VENT PIPE SHOWING TWO 30 FT. (9 M) SECTIONS OF FLEX LINER PIPE LENGTH (OPTIONAL) CO-AXIAL TO CO-LINEAR CONNECTOR PART #923GCL CHIMNEY LINER TERMINA ...

  • Hearth and Home Technologies PALOMA-BL - page 22

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 22 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY SEALANT -ADHESIVE 10 in. x 10 in. (254 mm x 254 mm) FRAMED OPENING IN W ALL STUDW ALL MASONRY CHIMNEY RETRO CONNECTOR FOUR MASONRY BOL TS (NOT INCLUDED) W ALL THIMBLE COVER Figure 5.25 Figure 5.26 1. Before cutting any holes, assemble the desi ...

  • Hearth and Home Technologies PALOMA-BL - page 23

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 23 HIGH WIND TERMINA TION CAP #SLK-991DA TOP ADAPT OR THREE SHEET MET AL SCREWS FLASHING 9. Attach the flex to the retro connector. Use three sheet metal screws to attach the flex liner to the connector (Figure 5.29). Mount the retro connector to the masonry wall using masonry bolts. Redrill ...

  • Hearth and Home Technologies PALOMA-BL - page 24

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 24 3/4 3/4 3/4 Assembling Slim Line T rim Ring and Heat Shield Installing Slim Line T rim Ring and Heat Shield Measure from the fl oor to the center of the vent pipe. Cut out a 9-1/2 in. (241 mm) hole in the wall. Hold the trim ring/heat shield assembly in place and put a mark on the shield ...

  • Hearth and Home Technologies PALOMA-BL - page 25

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 25 FIG. A 90 DEGREE ELBOW FIG. C MINIMUM CLEARANCE HTI VENT HHW2 PART #841-0670 (RECOMMENDED FOR OPTIMUM PERFORMANCE) TRIM RING WALL THIMBLE CENTER LINE MINIMUM OF 6 IN. (152 MM) OF PIPE THROUGH THE WALL INTERIOR WALL - 2 IN. (51 MM) CLEARANCE FROM REAR OF STOVE HEAT SHIELD OVER TOP HALF OF P ...

  • Hearth and Home Technologies PALOMA-BL - page 26

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 26 Any damaged valve components should not be installed. If a valve or regulator has been dropped or appears to have been modi fi ed, the valve or regulator should not be installed. T ools required : #2 Phillips head screwdriver; Power drill (a 90° drill is helpful); T amper-resistant T orx ...

  • Hearth and Home Technologies PALOMA-BL - page 27

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 27 RUB BER GA SK ET RE GULATO R VA LV E Figure 6.2 13. Place the round LP label on the bottom base pan. Place the propane conversion plate adjacent to the existing rating plate. Figure 6.4 ORIFICE SPUD PILOT TUBE ASSEMBL Y 1 1. Using a 3/8 in. (10 mm) nut driver or wrench, remove the NG ori ? ...

  • Hearth and Home Technologies PALOMA-BL - page 28

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 28 V erify the performance of the ignition system: 1. V erify pilot sparks, pilot lights, pilot stops sparking, and the main burner turns "ON". 2. T urn the appliance "OFF". V erify that both the pilot and burner turn "OFF". 3. Repeat Step 1 above. 4. With the bu ...

  • Hearth and Home Technologies PALOMA-BL - page 29

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 29 If the pressure is not suf fi cient, ensure: • The piping used is large enough. • The supply regulator is adequately adjusted. • That the total gas load for the residence does not exceed the amount supplied. The supply regulator (the regulator that attaches directly to the residence ...

  • Hearth and Home Technologies PALOMA-BL - page 30

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 30 C. IntelliFire ® Ignition System Wiring This appliance requires a 1 10 V AC supply to the appliance junction box for operation. A wiring diagram is shown in Figure 7.2 on the next page. This appliance is equipped with an IntelliFire ® control valve which operates on a 3 volt system. This ...

  • Hearth and Home Technologies PALOMA-BL - page 31

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 31 Figure 7.2 NOTE: Appliance will not operate unless properly grounded. * TRANSFORMER 3 V AC PLUG IN VA LV E GROUND TO APPLIANCE CHASSIS PIGGYBACK ON/OFF SWITCH INTERMITTENT PILOT IGNITOR IGNITION MODULE 3 V AC I S WHT ORG RED ORG BRN GRN BRN BLACK BA TTERY P ACK GROUND REMOTE CONTROL HOT NE ...

  • Hearth and Home Technologies PALOMA-BL - page 32

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 32 Figure 7.4 Junction Box Wired to W all Switch E. W all Switch Installation for Fan (Optional) If the box is being wired to a wall mounted sw itch for use with a fan (See Figure 7.4): • The power supply for the appliance must be brought into a switch box. • The power can then be supplie ...

  • Hearth and Home Technologies PALOMA-BL - page 33

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 33 B. Unbolting Appliance from the Pallet The appliance is bolted and screwed to the pallet for ship- ping. Use a 1/2 in. socket to remove the bolt in center of bottom plate. Use a Phillips screwdriver to remove the two screws in the front of the bottom plate and the two screws holding the me ...

  • Hearth and Home Technologies PALOMA-BL - page 34

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 34 C. Leveling and Lagging Down the Appliance Figure 8.6 LAGGING CLEARANCE HOLE Using pliers, adjust the counterscrews to level the appli- ance. Lagging the appliance down is REQUIRED . After unbolting the appliance from the pallet, insert two 1/4 20 x 1/1/2 counterscrews. Using pliers, adjus ...

  • Hearth and Home Technologies PALOMA-BL - page 35

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 35 Figure 8.1 1 Figure 8.12 Figure 8.10 Figure 8.9 E. T op to Rear V ent Conversion Kit Contents: T op cover (no hole); Back panel (with hole). T ools Required: Power drill; #2 Phillips bit; 5/32 in. (4 mm) Allen wrench; 5/8 in. (16 mm) open end wrench; high-temp silicone sealant (optional). ...

  • Hearth and Home Technologies PALOMA-BL - page 36

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 36 9. Install the cover plate removed from the rear of the appliance to the top of the appliance with the screws previously removed. (Figure 8.13). 10. Install the new solid top. Figure 8.13 F . Shutter Adjustment The shutter is located on the underside of the burner , on the burner neck (see ...

  • Hearth and Home Technologies PALOMA-BL - page 37

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 37 I. Positioning the Logs Remove the ignitor shield from the pilot assembly prior to installing the logs. (Figure 8.18). Figure 8.19 H. Installing the Baf fl e The baf fl e is shipped wrapped, inside the fi rebox. Install the baf fl e with the embedded “T” side up, place it on top of ...

  • Hearth and Home Technologies PALOMA-BL - page 38

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 38 J. Mineral W ool Figure 8.21 K. Optional Blower The GFK-160A Blower has been designed to circulate room air through the appliance to enhance heat output. The GFK-160A blower system operates on 120 V AC, 60 Hz power . This is available through a receptacle in the factory installed junction ...

  • Hearth and Home Technologies PALOMA-BL - page 39

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 39 Attach enclosed wires to the temperature sensor switch/ bracket assembly . The blue wire attaches to the rear of the bracket and one of the black wires from the variable speed control attaches closest to the prepunched screw hole. See Figure 8.24. F AN OUTLET CLIP V ARIABLE SPEED CONTROL & ...

  • Hearth and Home Technologies PALOMA-BL - page 40

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 40 Recommended operating procedures Ignite the fire in the appliance with the variable speed control switch in an "ON" position. The fan will automati- cally turn on when the temperature sensor switch closes at approximately 110 degrees Fahrenheit. Heated air should be delivered at ...

  • Hearth and Home Technologies PALOMA-BL - page 41

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 41 Figure 8.30 Blower Wiring Diagram BLUE V ARIABLE SPEED SWITCH TEMPERA TURE SENSOR SWITCH JUNCTION BOX Shock hazard. • Replace damaged wire with type 105º C rated wire. • Wire must have high temperature insulation. W ARNING ...

  • Hearth and Home Technologies PALOMA-BL - page 42

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 42 Installing flame control solenoid Remove the screw and knob from the variable regulator and discard. Unscrew the nut from the regulator and discard. Remove the bag containing a washer and blue and red plungers from the side of the flame control solenoid. Place washer on flame control solen ...

  • Hearth and Home Technologies PALOMA-BL - page 43

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 43 RED JUMPER WIRE TO BROWN W H I TE ORANG E INTERMITTEN T PILOT IGNITOR IGNITION MODULE 3 VAC REMOTE RECEIVER ORANGE GREEN BLACK RED VALVE GROUND TO FIREPLACE CHASSIS TRANSFORMER 3 VAC PLUG IN ORA NGE ORANGE RED RED FLAME CONTROL SOLENOID BATTERY PACK I S RED RED ORANGE ORANGE BRN ORANGE ORA ...

  • Hearth and Home Technologies PALOMA-BL - page 44

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 44 N. Inner Glass Door Assembly Replacement Turn the appliance OFF and let it cool down before replac- ing the inner glass door assembly. With the front door assembly removed from the appliance, remove the inner glass door assembly by disengaging the spring-loaded latches at the bottom of the ...

  • Hearth and Home Technologies PALOMA-BL - page 45

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 45 B. Controls On/off Switch: When this switch is in the ON position, the pilot ignitor is engaged until temperature is established. The burner automatically turns on. V alve V ariable Control: This knob controls the flame height from low (“LO”) to high (“HI”). The indicator on the va ...

  • Hearth and Home Technologies PALOMA-BL - page 46

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 46 C. Lighting Appliance 1. T urn off all electric power to the appliance. 2. This appliance is equipped with an ignition device which automatically lights the burner . Do not try to light the burner by hand. 3. Wait fi ve (5) minutes to clear out any gas. Then smell for gas, including near ...

  • Hearth and Home Technologies PALOMA-BL - page 47

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 47 Initial Break-in Procedure When you light the appliance, you may notice that it pro- duces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to ...

  • Hearth and Home Technologies PALOMA-BL - page 48

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 48 1 0 10 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service person in the diagnosis of a problem and the corrective ...

  • Hearth and Home Technologies PALOMA-BL - page 49

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 49 Intelli fi re Ignition System - (continued) Symptom Possible Cause Corrective Action 3. (Continued) Pilot lights but continues to spark, and main burner will not ignite. (If the pilot contin- ues to spark after the pilot fl ame has been lit, fl ame recti fi cation has not oc- curred.) ...

  • Hearth and Home Technologies PALOMA-BL - page 50

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 50 1 1 11 Maintaining and Ser vicing Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a quali fi ed service technician should perform an appliance checkup at the beginning of each heating season. Annual inspection by qua ...

  • Hearth and Home Technologies PALOMA-BL - page 51

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 51 Inspect Maintenance T asks 1. Inspect for scratches, dents or other damage and repair as necessary . 2. V erify no obstructions to air fl ow through the louvers. 3. V erify maintenance of proper clearance to combustible household objects. Gasket Seal, Glass Assembly and Glass 1. Inspect g ...

  • Hearth and Home Technologies PALOMA-BL - page 52

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 52 Height includes 3/8 in (9.53 mm) hearth pad B C I G D H F E A Hearth Pad Figure 12.1 Appliance Dimensions Location Inches Millimeter Location Inches Millimeter A 18-7/8 479 F 7-1/8 181 B 40-3/4 1035 G 30 762 C 40-3/8 1025 H 28-7/8 733 D 15-7/8 403 I 33-3/4 857 E3 7 6 1 2 12 Reference Mater ...

  • Hearth and Home Technologies PALOMA-BL - page 53

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 53 Height includes 3/8 in (9.53 mm) hearth pad Height includes 3/8 in (9.53 mm) hearth pad F G C E B A Hearth Pad D Figure 12.2 Appliance Dimensions with Stone Surround Location Inches Millimeter Location Inches Millimeter A 29-5/8 753 E 16-7/8 428 B 24-3/8 620 F 34-5/8 879 C 30-1/4 768 G 44- ...

  • Hearth and Home Technologies PALOMA-BL - page 54

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 54 C. V ent Components Diagram Figure 12.3 SLP Series V ent Components 9-7/16 in. 240 mm 6-9/16 in. 167 mm 6-9/16 in. 167 mm 6-9/16 in. 167 mm 6-9/16 in. 167 mm 6 in. 152 mm 6-1/2 in. 165 mm 9-3/4 in. 248 mm 9-1/4 in. 235 mm 7-1/4 in. 184 mm 7-1/4 in. 184 mm 5-1/4 in. 133 mm 25-1/4 in. 641 mm ...

  • Hearth and Home Technologies PALOMA-BL - page 55

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 55 D. V ent Components List COMPONENTS SLP-WT -BK Ceiling Support / Wall Thimble, Black SLP-CCS-BK Cathedral Ceiling Support, Black SLP6-BK 6 inch Pipe Length, Black SLP4-BK 9 inch Pipe Length, Black SLP12-BK 12 inch Pipe Length, Black SLP34-BK 24 inch Pipe Length, Black SLP36-BK 36 inch Pipe ...

  • Hearth and Home Technologies PALOMA-BL - page 56

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 56 Beginning Manufacturing Date: July 2005 Ending Manufacturing Date: ______ E. Service Parts Service Parts Diagram P ALOMA Part number list on following page. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Log Set Assembly ...

  • Hearth and Home Technologies PALOMA-BL - page 57

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 57 E. Service Parts List P ALOMA IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTI ...

  • Hearth and Home Technologies PALOMA-BL - page 58

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 58 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION COMMENTS P ART NUMBER T emp ...

  • Hearth and Home Technologies PALOMA-BL - page 59

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 59 Beginning Manufacturing Date: July 2005 Ending Manufacturing Date: ______ E. Service Parts V alve Diagram P ALOMA IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in th ...

  • Hearth and Home Technologies PALOMA-BL - page 60

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 60 F . Limited Lifetime W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in t ...

  • Hearth and Home Technologies PALOMA-BL - page 61

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 61 F . Limited Lifetime W arranty (continued) • This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or c ...

  • Hearth and Home Technologies PALOMA-BL - page 62

    Heat & Glo • Paloma • 7031-220 Rev . P • 10/08 62 Heat & Glo, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www .heatnglo.com G. Contact Information Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer , please ...

Manufacturer Hearth and Home Technologies Category Indoor Fireplace

Documents that we receive from a manufacturer of a Hearth and Home Technologies PALOMA-BL can be divided into several groups. They are, among others:
- Hearth and Home Technologies technical drawings
- PALOMA-BL manuals
- Hearth and Home Technologies product data sheets
- information booklets
- or energy labels Hearth and Home Technologies PALOMA-BL
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hearth and Home Technologies PALOMA-BL.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hearth and Home Technologies PALOMA-BL, service manual, brief instructions and user manuals Hearth and Home Technologies PALOMA-BL. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hearth and Home Technologies PALOMA-BL.

Similar manuals

A complete manual for the device Hearth and Home Technologies PALOMA-BL, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hearth and Home Technologies PALOMA-BL by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hearth and Home Technologies PALOMA-BL.

A complete Hearth and Home Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hearth and Home Technologies PALOMA-BL - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hearth and Home Technologies PALOMA-BL, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hearth and Home Technologies PALOMA-BL, that we can find in the current document
3. Tips how to use the basic functions of the device Hearth and Home Technologies PALOMA-BL - which should help us in our first steps of using Hearth and Home Technologies PALOMA-BL
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hearth and Home Technologies PALOMA-BL
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hearth and Home Technologies PALOMA-BL in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hearth and Home Technologies PALOMA-BL?

Use the form below

If you did not solve your problem by using a manual Hearth and Home Technologies PALOMA-BL, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies PALOMA-BL it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)