English dropdown-ico

Manual Nilfisk-ALTO EZ-8

12 pages 0.33 mb
Download

Go to site of 12

Summary
  • Nilfisk-ALTO EZ-8 - page 1

    Form No. 78425B 10/01 AMERICAN SANDERS TECHNOLOGY Printed in the U.S.A. READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your American Sanders Technology machine could result in injury to you or to oth ...

  • Nilfisk-ALTO EZ-8 - page 2

    Page 2 AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual Operator Safety Instructions ......................................................... 3 Introduction and Machine Specifications ....................................... 5 How to Transport the Machine ...................................................... 6 Machine Set-Up ...... ...

  • Nilfisk-ALTO EZ-8 - page 3

    AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual Page 3 DANGER means: Severe bodily injury or death can occur to you or other personnel if the DANGER statements found on this machine or in this Owner's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this Owner's Manual and on your ...

  • Nilfisk-ALTO EZ-8 - page 4

    Page 4 AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual DANGER: Electrocution or injury could occur if the power cord encounters the sanding drum. Keep the cord clear of the sanding drum. Always lift the power cord over the machine. DANGER: Electrocution or severe injury could occur if machine is connected to an electrical system th ...

  • Nilfisk-ALTO EZ-8 - page 5

    AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual Page 5 Introduction & Machine Specifications Model 07057A 07058A 07059A 07060A Abrasive Size 8 in x 19 3 / 16 in 8 in x 19 in 8 in x 19 3 / 16 in 8 in x 19 in sheet sleeve sheet sleeve Abrasive Rate 2680 ft/min 2830 ft/min 2230 ft/min 2360 ft/min Drum Rate 1800 RPM 1800 RPM 1500 R ...

  • Nilfisk-ALTO EZ-8 - page 6

    Page 6 AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual How to T ransport the Machine Transporting the Machine With Limited Cargo Area: To transport the machine, follow this procedure: 1. Lower sanding drum with control lever. See figure #1. 2. Slide collar beyond overlap of control link; remove pin from notch. See figure #2. 3. Twi ...

  • Nilfisk-ALTO EZ-8 - page 7

    AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual Page 7 Machine Set-up To set up the machine follow this procedure: 1. Familiarize yourself with the machine. Read all danger, warning, and caution statements as well as the Operator's Manual. If operator is unable to read English, have the manual explained before operating. 2. In ...

  • Nilfisk-ALTO EZ-8 - page 8

    Page 8 AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual How to Operate the Machine (cont.) CAUTION: T o prevent damage to the surface, make sure the machine is always moving when the sanding drum is in contact with the floor. 2. Work right to left. For each forward pass, move the machine 4" over the pass you have just finished. ...

  • Nilfisk-ALTO EZ-8 - page 9

    AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual Page 9 945390/25 945391/25 945392/25 945930/10 945416/10 945395/25 945933/10 945418/10 945397/25 945398/25 945935/10 945420/10 945399/25 945936/10 945421/10 945400/25 945937/10 945422/10 Sanding Cuts and Sandpaper 12 grit For removing gross imperfections and restore 16 grit evenness t ...

  • Nilfisk-ALTO EZ-8 - page 10

    Page 10 AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual Sander Adjustment Procedures DANGER: Electrocution could occur if main- tenance and repairs are performed on a unit that is not properly dis- connected from the power source. Disconnect the power supply be- fore attempting any maintenance or service. DANGER : Moving parts of t ...

  • Nilfisk-ALTO EZ-8 - page 11

    AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual Page 11 Routine Maintenance The following items need to be periodically inspected and maintained to keep your sander in good working condition. Sanding Chamber Periodically blow out the sanding chamber to prevent large accumulations of debris which could interfere with the performance ...

  • Nilfisk-ALTO EZ-8 - page 12

    Page 12 AMERICAN SANDERS TECHNOLOGY EZ - 8 Sander Operator's Manual T roubleshooting Problem Cause Action Drive belts jump teeth or squeak. Damaged belt. Replace belt. Insufficient tension. Tension drive belt. Poor belt tracking. Align Pulley. Squealing, growling or grinding Damage and/or worn bearing. Remove drive belts, rotate arbor noise co ...

Manufacturer Nilfisk-ALTO Category Sander

Documents that we receive from a manufacturer of a Nilfisk-ALTO EZ-8 can be divided into several groups. They are, among others:
- Nilfisk-ALTO technical drawings
- EZ-8 manuals
- Nilfisk-ALTO product data sheets
- information booklets
- or energy labels Nilfisk-ALTO EZ-8
All of them are important, but the most important information from the point of view of use of the device are in the user manual Nilfisk-ALTO EZ-8.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Nilfisk-ALTO EZ-8, service manual, brief instructions and user manuals Nilfisk-ALTO EZ-8. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Nilfisk-ALTO EZ-8.

Similar manuals

A complete manual for the device Nilfisk-ALTO EZ-8, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Nilfisk-ALTO EZ-8 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Nilfisk-ALTO EZ-8.

A complete Nilfisk-ALTO manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Nilfisk-ALTO EZ-8 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Nilfisk-ALTO EZ-8, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Nilfisk-ALTO EZ-8, that we can find in the current document
3. Tips how to use the basic functions of the device Nilfisk-ALTO EZ-8 - which should help us in our first steps of using Nilfisk-ALTO EZ-8
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Nilfisk-ALTO EZ-8
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Nilfisk-ALTO EZ-8 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Nilfisk-ALTO EZ-8?

Use the form below

If you did not solve your problem by using a manual Nilfisk-ALTO EZ-8, ask a question using the form below. If a user had a similar problem with Nilfisk-ALTO EZ-8 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)