Manual Hearth and Home Technologies HST-48D

48 pages 3.73 mb
Download

Go to site of 48

Summary
  • Hearth and Home Technologies HST-48D - page 1

    1 Owner ’ s Manual Installation and Operation Models: HST -48D Wood Burning Fireplace DO NOT DISCARD THIS MANUAL NOTICE • Important operating and maintenance instructions included. • Leave this manual with party responsible for use and operation. • Read, understand and follow these instructions for safe installation and operation. DO NOT DI ...

  • Hearth and Home Technologies HST-48D - page 2

    2 Read this manual before installing or operating this fi replace. Please retain this owner ’ s manual for future reference. Homeowner Reference Information Model Name: Date purchased/installed: Serial Number: Location on fi replace: Dealership purchased from: Dealer phone: Notes: We recommend that you record the following pertinent information ...

  • Hearth and Home Technologies HST-48D - page 3

    3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury . ? ...

  • Hearth and Home Technologies HST-48D - page 4

    4 W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. W arranty starts with date of purchase b ...

  • Hearth and Home Technologies HST-48D - page 5

    5 This limited warranty does not extend to or include surface ? nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, ? rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, baf? es, ? repots, doors, or ? rebox area are no ...

  • Hearth and Home Technologies HST-48D - page 6

    6 1 1 Listing and Code Appro v als NOTICE: This fireplace is tested and approved as a decorative fi replace. It should not be factored as a primary heat source in residential heating calculations. W ARNING! Risk of Fire! Hearth & Home T echnologies disclaims any responsibility for , and the warranty and agency listing will be voided by the fol ...

  • Hearth and Home Technologies HST-48D - page 7

    7 2 2 Operat ing Instr uct ions W ARNING! DO NOT operate fi replace before reading and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury . User Guide W ARNING Hot glass will cause burns. • DO NOT touch glass until it is cooled • NEVER allow children to touch gl ...

  • Hearth and Home Technologies HST-48D - page 8

    8 • The fi rst three or four fi res should be of moderate size to allow the oils and binders to be burned from the fi replace and the refractory and paint to cure. Y ou may notice an industrial odor the fi rst few fi res. This is considered normal. • Use well-seasoned wood. • Open the fl ue damper to a fully open position. • Place cru ...

  • Hearth and Home Technologies HST-48D - page 9

    9 P ARTL Y OPEN INCORRECT FULL Y OPEN CORRECT P ARTL Y CLOSED INCORRECT FULL Y CLOSED CORRECT Figure 2.2 Operating Positions of Bi-fold Doors W ARNING! Risk of Fire and Smoke! Fireplaces equipped with doors should be operated only with doors fully open or doors fully closed. If doors are left partly open, gas and fl ame may be drawn out of the fi ...

  • Hearth and Home Technologies HST-48D - page 10

    10 M. Wood Fuel Hardwood vs Softwood Y our fi replace performance depends on the quality of the fi rewood you use. • Seasoned wood contains about 8,000 BTUs per pound . • Hard woods are more dense than soft woods. • Hard woods contain 60% more BTUs than soft woods. • Hard woods require more time to season, burn slower and are harder to ig ...

  • Hearth and Home Technologies HST-48D - page 11

    11 3 3 Maintainance and Ser vice Figure 3.1 Chimney & T ermination Cap Cleaning A. Disposal of Ashes Frequency: When they reach bottom of grate By: Homeowner W ARNING! Risk of Fire! Ashes could contain hot em- bers. • Place ashes in a metal container with a tight- fi tting lid. • The closed container should be placed on a noncombustible ? ...

  • Hearth and Home Technologies HST-48D - page 12

    12 C. Check Firebox Refractory Frequency: After each ash removal By: Homeowner D. Inspect Grate Frequency: After each ash removal By: Homeowner Inspect grate for: • W arping or sagging 1-1/2 in. (38 mm) or more • Broken welds • Burn-through of grate bars For safe operation, replace only with an approved grate from Hearth & Homes T echnolo ...

  • Hearth and Home Technologies HST-48D - page 13

    13 4 4 T roubleshooting Guide Start Fire Problems Possible Cause Solution Can’t get fi re started Excessive smoke or spillage Burns too slowly Smolders, sizzles Not enough kindling/paper or no kindling/paper Use dry kindling, more paper . Arrange kindling & wood for air movement. Damper closed/not fully open Open damper . Not enough air for ...

  • Hearth and Home Technologies HST-48D - page 14

    14 5 5 Get ting Star ted A. T ypical Fireplace System Installer Guide Heat & Glo • HST -48D US-CAN • 4012-040 • Rev F • 1 1/08 ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) Non-combustible roof flashing maintains minimum clearance around chimney Additional later ...

  • Hearth and Home Technologies HST-48D - page 15

    15 Negative pressure results from the imbalance of air avail- able for the fi replace to operate properly . It can be stron- gest in lower levels of the house. Causes include: • Exhaust fans (kitchen, bath, etc.) • Range hoods • Combustion air requirements for furnaces, water heaters and other combustion appliances • Clothes dryers • Loc ...

  • Hearth and Home Technologies HST-48D - page 16

    16 Marginal Location: • Below peak Location NOT recommended: • Not the highest point of the roof • Wind loading possible Multi-level Roofs Windward Leeward Recommended Location: • Above peak Recommended: • Insulated exterior chase in cooler climates Recommended Location: • Above peak • Inside heated space Location NOT recommended: • ...

  • Hearth and Home Technologies HST-48D - page 17

    17 Before beginning the installation be sure the following tools and building supplies are available: Reciprocating saw Framing material Pliers Non-combustible sealant Hammer Gloves Phillips screwdriver Framing square Flat blade screwdriver Electric drill and bits Plumb line Safety glasses Level T ape measure 1/2-3/4 in. length, #6 or #8 self-drill ...

  • Hearth and Home Technologies HST-48D - page 18

    18 6 6 F raming & Clearances 66 in. (1676 mm) 42 in. (1067 mm) 20 in. (508 mm) (hearth extension) 64 in. (1626 mm) 12 in. (305 mm) min. to perpendicular wall. Figure 6.1 Fireplace Locations (Framing dimensions shown) A. Select Fireplace Location Note: 1/2 in. ( 1 3 mm ) dist ance from firepla ce to com bu sti bl e m at eri al s. Note: In additi ...

  • Hearth and Home Technologies HST-48D - page 19

    19 B. Clearances W ARNING! Risk of Fire! Y ou must comply with all minimum air space clearances to combustibles as speci fi ed in Fig- ure 6.2. DO NOT pack required air spaces with insulation or other materials. Heat & Glo • HST -48D US-CAN • 4012-040 • Rev F • 1 1/08 (roof) (insulation) 0 in. to level of standoffs Attic Insulation Shi ...

  • Hearth and Home Technologies HST-48D - page 20

    20 47 in. [1 194 mm] width of fireplace 42 in. [1067 mm] fireplace opening 9 3/4 in. [248 mm] 12 in. [305 mm] 12 in. [305 mm] 1 1 3/8 in. [289 mm] FLUSH FRONT 4 in. [102 mm] BRICK FRONT 50° angle 39° angle Gridlines at 1 in. scale D. Frame the Fireplace Figure 6.4 shows typical framing using combustible materials (2x4 lumber shown). • Observe a ...

  • Hearth and Home Technologies HST-48D - page 21

    21 7 7 Installation of Fireplace CAUTION! Risk of Cuts/Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp. A. Things to Consider • Location of chimney air kit inlet (see Figure 5.1 and 7.4) • Location(s) of outside air kit • Electrical connections and/or wall switch • Gas line piping B. Pos ...

  • Hearth and Home Technologies HST-48D - page 22

    22 Outlet placed higher than 3 ft below the termination cap Attic space Garage or combustible liquids storage Outlet blocked by snow , leaves, etc. Clear area outside house or in ventilated crawl space YES NO NO NO NO Use only duct materials specified by manufacturer (preferably with short run or mainly straight duct, except small dip for cold air ...

  • Hearth and Home Technologies HST-48D - page 23

    23 Outside Air Hood Outside Air Plate Assembly 2 Wire T ies Flexible Duct (not supplied) Figure 7.5 Outside Air Installation E. Install Outside Air Kit • Keep duct runs short and straight to minimize restriction. A small dip is acceptable for a cold air trap. • The outside air kit must be installed using the outside air cover (see Dimensions, S ...

  • Hearth and Home Technologies HST-48D - page 24

    24 Chimney must extend beyond combustible roof structure Maintain minimum height of chimney above roof Additional support for tall chimneys Install roof flashing according to minimum requirements Maintain minimum clearances to combustibles as specified Offsets/returns may not exceed 30° from vertical Lock chimney sections together firmly to resist ...

  • Hearth and Home Technologies HST-48D - page 25

    25 A. Chimney Requirements Measure vertical distances from the base of the fi replace as shown in Figure 8.2. d & g Ceiling Firestop h i 58-7/8 in. (1495 mm) Effective Height a,b,c,f 1 1-10 in. (279-254 mm) adapter required in Canada. Figure 8.2 Chimney Requirements (refer to list in Sect. 5.A.) T able 8.1 ft meters a. Minimum overall straight ...

  • Hearth and Home Technologies HST-48D - page 26

    26 T able 8.2 B. Using Offsets/Returns • Use an of fset/return to bypass overhead obstructions. • An of fset and return can be used as a single entity or separated by chimney section(s). W ARNING! Risk of Fire! DO NOT use offset/returns greater than 30°. Chimney draft will be restricted and could cause overheating and fi re. • Measure the s ...

  • Hearth and Home Technologies HST-48D - page 27

    27 Figure 8.4 Assembling Chimney Sections • Support the pipe during construction and check to be sure inadvertent loading has not dislodged the chimney section from the fi replace or at any chimney joint. • Attach a straight chimney section or an offset to the top of the fi replace. • Place inner fl ue to the inside of the chimney section ...

  • Hearth and Home Technologies HST-48D - page 28

    28 ROOM ABOVE (non-insulated ceiling) A TTIC ABOVE (insulated ceiling) B A Ceilng firestop from bottom Ceiling firestop from top Note: Use same dimensional lumber for framing ceiling firestop and joists. Figure 8.5 Installing the Ceiling Firestop • Install a ceiling fi restop whenever chimney penetrates ceiling/ fl oor . • Mark and cut an ope ...

  • Hearth and Home Technologies HST-48D - page 29

    29 3 in. (76 mm) overlap Insert three screws Bend inward 90° Bend remaining tabs to rest against pipe to prevent insulation from falling in. Figure 8.6 Prepare Attic Insulation Shield Installation of a ceiling fi restop is required • Refer to Figures 8.6 - 8.8. • Roll the shield (around the chimney if already installed) until you have a 3 in. ...

  • Hearth and Home Technologies HST-48D - page 30

    30 Figure 8.9 Ceiling/Attic Construction H. Complete Installation W ARNING! Risk of Fire! Y ou MUST maintain 2 in. (51 mm) air space to insulation and other combustible materials around the chimney system. Failure to do so could cause overheating and fi re. • Keep chimney sections from separating or twisting. • Y ou may secure straight chimney ...

  • Hearth and Home Technologies HST-48D - page 31

    31 Slanted Roofs Flat Roofs Chimney must extend 3 ft (.9 m) above the roof Chimney must extend 2 ft (.6 m) above any portion of the roof or adjacent structures within 10 ft (3 m) of the chimney Chimney must extend 3 ft (.9 m) above the roof Chimney must extend 2 ft (.6 m) above any portion of the roof or adjacent structures within 10 ft (3 m) of th ...

  • Hearth and Home Technologies HST-48D - page 32

    32 9 9 Chase Installations Ceiling Firestop Metal Chase T op Round T ermination Cap False Ceiling Insulation in the outside walls of the chase Attic Insulation Shield Chimney Ceiling Firestop T abs False Ceiling False Ceiling Insulation Insulation Figure 9.1 Chase Assembly 1 2 1. Chimney of fset through exterior wall and enclosed in chase. 2. Chase ...

  • Hearth and Home Technologies HST-48D - page 33

    33 Slope Downward (1/4 in. per foot minimum) T urn-down Drip Edge Chase 2 in. (51 mm) Collar on Chase T op .018 (26 ga) min. Galvanized Chase T op Figure 9.3 Chase T op Construction B. Install Fireplace & Chimney Install as per Sections 7 and 8. Heat & Glo • HST -48D US-CAN • 4012-040 • Rev F • 1 1/08 C. Install Chase T op • Y ou ...

  • Hearth and Home Technologies HST-48D - page 34

    34 D. Install T ermination Cap Install the chimney sections up through the chase enclo- sure. • Refer to termination cap instructions. W ARNING! Risk of Fire! The minimum overlap of cap to pipe (as shown in the following illustrations) MUST be met or chimney may separate from cap. Separation allows sparks, heat and embers to escape. NOTICE: Paint ...

  • Hearth and Home Technologies HST-48D - page 35

    35 Heat & Glo • HST -48D US-CAN • 4012-040 • Rev F • 1 1/08 Chimney Pipe Chase T op T ermination Cap Chase Collar 2 in. (51 mm) Minimum Height T ermination cap pipe and chimney section must overlap 1-1/2 in. (38 mm) Place waterproof sealer under each flange of the termina- tion cap and on top of each screw to help prevent leaks. The las ...

  • Hearth and Home Technologies HST-48D - page 36

    36 3 in. (76 mm) tall legs Ø 17 1/2 in. (444.5 mm) Round Hole to fit over cap Length x Width to fit inside shroud Figure 10.1 Radiation Shield 1 0 10 Shrouds • Chase top shrouds may be fi eld constructed where permitted by regional building codes. W ARNING! Risk of Fire! Shrouds must be constructed as speci fi ed. Improper construction may ove ...

  • Hearth and Home Technologies HST-48D - page 37

    37 3 in. (76 mm) Min. Opening Height Min. Base Dim Min. Height above radiation shield Min. Base Dim 3 in. (76 mm) Min. Radiation Shield Height from top of Chase Min. Opening Width Figure 10.3 Mailbox Style Shroud Dimensions Minimum Opening Height Minimum Base Dimension Min. Opening Width Min . Base Dimension Minimum Height above Radiation Shield Ch ...

  • Hearth and Home Technologies HST-48D - page 38

    38 1 1 11 Fi n i s hi n g A. Non-Combustible Materials • Materials which will not ignite and burn, composed of any combination of the following: - Steel - Iron - Brick - T ile - Concrete - Slate - Glass - Plasters • Materials reported as passing ASTM E 136, Standard T est Method for Behavior of Metals, in a V ertical T ube Furnace at 750° C B. ...

  • Hearth and Home Technologies HST-48D - page 39

    39 D. Finishing Material Refer to Sections 1 1.A. and Sections 1 1.B. for combus- tible/noncombustible materials. Refer to Figure 1 1.2 for noncombustible zone. W ARNING! Risk of Fire! Y ou must maintain clearances. • Use only non-combustible framing material below standoffs. • Sheetrock, wood or other combustibles must NOT be used as sheathing ...

  • Hearth and Home Technologies HST-48D - page 40

    40 E. Combustible Mantel • See Figure 1 1.4. • A combustible mantel may be positioned no lower than 12 in. (305 mm) above the top of the fi replace opening. • A combustible mantel may have a maximum depth of 12 in. (305 mm). • Combustible trim and materials cannot be placed within 6 in. (152 mm) of the fi replace opening (top or sides). ? ...

  • Hearth and Home Technologies HST-48D - page 41

    41 Firebox Repack Insulation Knockout Combustible Materials Maintain air clearance to combustibles. Gas Line Combustible materials may be located at zero clearance to gas line beyond 4 in. (102 mm) from fireplace side. Gas Line 1 1/2 in. (38 mm) air space around pipe Refractory Seal with fireplace mortar or non-combust- ible sealant 4 in. (102 mm) ...

  • Hearth and Home Technologies HST-48D - page 42

    42 1 3 13 Refer ence Materials A. Fireplace Dimensions 58-7/8 in. (1496 mm) (effective height) 42 in. (1067 mm) 23 in. (585 mm) 7-1/2 in. (192 mm) 13 in. [330 mm] dia. 39-1/8 in. (995 mm) 47 in. (1 194 mm) 28 in. (71 1 mm) 23-1/2 in. (597 mm) 14 in. (356 mm) Gas Knockout 8-3/8 in. (213 mm) 14 in. (356 mm) 39-1/8 in. (994 mm) 39-1/8 in. (994 mm) 38- ...

  • Hearth and Home Technologies HST-48D - page 43

    43 B. Optional Components 20 in. (508 mm) 66 in. (1676 mm) 1/2 in. (13 mm) HX4 Hearth Extension Bi-fold Glass Doors Heat & Glo • HST -48D US-CAN • 4012-040 • Rev F • 1 1/08 See your Heat & Glo dealer for a complete listing of optional components. ...

  • Hearth and Home Technologies HST-48D - page 44

    44 B. Chimney Components The following pictures show only those chimney components which may be safely used with this fi replace. ID4 Insulated Duct UD4 Uninsulated Duct 42 in. (1067 mm) 4 in. (102 mm) i 42 in. (1067 ) 4 in. (102 mm) i Heat & Glo • HST -48D US-CAN • 4012-040 • Rev F • 1 1/08 Catalog # Description US CAN CAK5A CAK5A Chi ...

  • Hearth and Home Technologies HST-48D - page 45

    45 TR-TVK TR T op V ent Kit Heat & Glo • HST -48D US-CAN • 4012-040 • Rev F • 1 1/08 AS10 Straight Attic Insulation Shield Assembled Diameter: 17 in./432 mm Height: 24 in./610 mm CB576 Chimney Joint Band 13 in. (330 mm) JB577 Chimney Joint Band 2 in. (51 mm) 13 in. (330 mm) A B 17 in. (432 mm) Catalog # A B FS538 0-deg. 17 in. 432 mm FS ...

  • Hearth and Home Technologies HST-48D - page 46

    46 A B C D LDS33/LDS46 Decorative Shroud Catalog # ABCD in. mm in. mm in. mm in. mm LDS33 36 914 36 914 8-1/2 216 1 1 279 LDS46 48 1219 72 1829 8-1/2 216 1 1 279 E D A C B Catalog # A B C D E LDS-BV in. 26 12-1/2 15-1/2 22 23 mm 660 318 394 533 584 LDS-BV Decorative Shroud Heat & Glo • HST -48D US-CAN • 4012-040 • Rev F • 1 1/08 CT56 Ch ...

  • Hearth and Home Technologies HST-48D - page 47

    47 C. Service Parts 5/08 Service Parts Service Parts Diagram 42 in. See-through Woodburning Fireplace Part number list on following page. HST -48D 2 1 8 6 91 0 1 1 7 5 12 4 3 Duct sold separately 13 14 15 Side of Fireplace Beginning Manufacturing Date: Aug 2001 Ending Manufacturing Date: Active 5/08 Service Parts Service Parts List 42 in. See-throu ...

  • Hearth and Home Technologies HST-48D - page 48

    48 – NOTES – D. Contact Information DO NOT DISCARD THIS MANUAL CAUTION • Important operating and maintenance instructions included. • Leave this manual with party responsible for use and operation. • Read, understand and follow these instructions for safe installation and operation. DO NOT DISCARD This product may be covered by one or mor ...

Manufacturer Hearth and Home Technologies Category Indoor Fireplace

Documents that we receive from a manufacturer of a Hearth and Home Technologies HST-48D can be divided into several groups. They are, among others:
- Hearth and Home Technologies technical drawings
- HST-48D manuals
- Hearth and Home Technologies product data sheets
- information booklets
- or energy labels Hearth and Home Technologies HST-48D
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hearth and Home Technologies HST-48D.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hearth and Home Technologies HST-48D, service manual, brief instructions and user manuals Hearth and Home Technologies HST-48D. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hearth and Home Technologies HST-48D.

A complete manual for the device Hearth and Home Technologies HST-48D, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hearth and Home Technologies HST-48D by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hearth and Home Technologies HST-48D.

A complete Hearth and Home Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hearth and Home Technologies HST-48D - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hearth and Home Technologies HST-48D, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hearth and Home Technologies HST-48D, that we can find in the current document
3. Tips how to use the basic functions of the device Hearth and Home Technologies HST-48D - which should help us in our first steps of using Hearth and Home Technologies HST-48D
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hearth and Home Technologies HST-48D
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hearth and Home Technologies HST-48D in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hearth and Home Technologies HST-48D?

Use the form below

If you did not solve your problem by using a manual Hearth and Home Technologies HST-48D, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies HST-48D it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)