Manual Cisco Systems 10BASE-FL

40 pages 0.94 mb
Download

Go to site of 40

Summary
  • Cisco Systems 10BASE-FL - page 1

    1 Cisco Systems, Inc. All rights reser ved. 170 West Tasman Drive San Jose, CA 95134-1706 USA Cisco Systems, Inc. Corporate Headquarters Copyright © 1998 T ext P ar t Number: P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Product Number s: P A-5EFL and P A-5EFL= Intr oduction This configuration note describes the inst ...

  • Cisco Systems 10BASE-FL - page 2

    2 P A-5EFL Ethernet 10BASE-FL P or t Adapter Installation and Configuration If Y ou Need More Information If Y ou Need More Inf ormation The Cisco IOS software running your router contains extensi ve features and functionality . The effecti ve use of many of man y of these features is easier if you have more information at hand. F or additional in ...

  • Cisco Systems 10BASE-FL - page 3

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 3 Tools and Parts Required T ools and P ar ts Required Y ou need the following tools and parts to install a port adapter . If you need additional equipment, contact a service representativ e for ordering information. • P A-5EFL(=) port adapter and one of the following: — VIP ...

  • Cisco Systems 10BASE-FL - page 4

    4 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Safety Guidelines Note Port adapters used with the 7200 VXR routers require the correct base hardware re vision in order to function. The following error message will occur on bootup if the incorrect hardw are revision is used: > PA-3-REVNOTSUPPORTED:PA in slot 1 (Ethe ...

  • Cisco Systems 10BASE-FL - page 5

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 5 Safety Warnings W arnung Dieses W arnsymbol bedeutet Gefahr . Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Be vor Sie mit der Arbeit an irgendeinem Gerät be ginnen, seien Sie sich der mit elektrischen Stromkreisen verb undenen Gefahre ...

  • Cisco Systems 10BASE-FL - page 6

    6 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Safety Guidelines T elephone Wiring Guidelines Use the following guidelines when w orking with any equipment that is connected to telephone wiring or to other network cabling: • Ne ver install telephone wiring during a lightning storm. • Ne ver install telephone jacks ...

  • Cisco Systems 10BASE-FL - page 7

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 7 IEEE 802.3 10BASE-FL Specifications changes. T ogether, Ethernet and IEEE 802.3 are the most widely used LAN protocols. They are well suited to applications where a local communication medium must carry sporadic, occasionally heavy traf fic at high peak data rates. The term 1 ...

  • Cisco Systems 10BASE-FL - page 8

    8 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration What Is the 5EFL P or t Adapter? T able 4 lists multimode optical-fiber parameters. T able 4 Multimode Optical-Fiber P arameters What Is the 5EFL P or t Adapter? The 5EFL port adapter provides up to fi ve IEEE 802.3 Ethernet 10B ASE-FL interfaces. (See Figure 1.) Each E ...

  • Cisco Systems 10BASE-FL - page 9

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 9 Port Adapter Locations on the VIP2 and in the Cisco 7200 Series Routers Figure 2 T wo P ort Adapters on a VIP2-15 or VIP2-40 (Horizontal Orientation Shown) Figure 3 T wo P ort Adapters on a VIP2-50 (Horizontal Orientation Shown) Note In the Cisco 7000, Cisco 7507, and Cisco 75 ...

  • Cisco Systems 10BASE-FL - page 10

    10 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration What Is the 5EFL P or t Adapter? Figure 4 P or t Adapters in the Cisco 7206 5EFL P or t Adapter LEDs The 5EFL port adapter contains the enabled LED, standard on all port adapters, and one status LED for each port, called the link LED. After system initialization, the ena ...

  • Cisco Systems 10BASE-FL - page 11

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 11 5EFL Port Adapter Multimode Fiber-Optic Cable and Receptacles 5EFL P or t Adapter Multimode Fiber-Optic Cable and Receptacles The interface connectors on the 5EFL port adapter are fi ve pairs of (ST) receptacles, designated as RX and TX . Y ou can use all fiv e connection p ...

  • Cisco Systems 10BASE-FL - page 12

    12 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration VIP2 and the 5EFL P or t Adapter Figure 7 VIP2-15 or VIP2-40 with T wo 5EFL P ort Adapter Installed (Horizontal Orientation Shown) Note Port adapters hav e a handle attached, but this handle is not shown to allo w a full view of detail on each port adapter’ s faceplate ...

  • Cisco Systems 10BASE-FL - page 13

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 13 Installing or Replacing a Port Adapter on a VIP2 Installing or Replacing a P or t Adapter on a VIP2 This section provides the standard procedures for installing or replacing a port adapter on the VIP2. Depending on the circumstances, you might need to install a new port adapt ...

  • Cisco Systems 10BASE-FL - page 14

    14 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration VIP2 and the 5EFL P or t Adapter Figure 9 Location of P or t Adapter Screw (P ar tial P or t Adapter View) Step 6 Remove the scre w that secures the port adapter (or blank port adapter). Step 7 With the scre w removed, grasp the handle on the front of the port adapter (o ...

  • Cisco Systems 10BASE-FL - page 15

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 15 Installing or Replacing a Port Adapter on a VIP2 Step 9 Remove the ne w port adapter from its antistatic container and position it at the opening of the slot. (See Figure 11.) Step 10 Carefully align the port adapter carrier between the upper and lower edges of the port adapt ...

  • Cisco Systems 10BASE-FL - page 16

    16 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration VIP2 and the 5EFL P or t Adapter Step 11 Carefully slide the new port adapter into the port adapter slot until the connector on the port adapter is completely mated with the connector on the motherboard. Figure 12 P or t Adapter Installed in a P or t Adapter Slot (Partia ...

  • Cisco Systems 10BASE-FL - page 17

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 17 Attaching 5EFL Port Adapter Interface Cables Attaching 5EFL P or t Adapter Interf ace Cables On a single 5EFL port adapter , you can use up to five pairs of ST fiber -optic connections. The 5EFL port adapter is an end station de vice and not a repeater . Y ou must connect t ...

  • Cisco Systems 10BASE-FL - page 18

    18 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration VIP2 and the 5EFL P or t Adapter After you verify that the ne w 5EFL port adapter is installed correctly (the enabled LED goes on), use the pri vileged-le vel configure command to configure the ne w interfaces. Be prepared with the information you will need, such as th ...

  • Cisco Systems 10BASE-FL - page 19

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 19 Configuring the 5EFL Interfaces Note If you remov e the 5EFL-equipped VIP2 from slot 3 and install it in slot 2, the addresses of those same 10B ASE-FL ports become 2/0/0 through 2/0/4 and 2/1/0 through 2/1/4. Figure 14 10B ASE-FL Interface P or t Number Example (Cisco 7505 S ...

  • Cisco Systems 10BASE-FL - page 20

    20 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration VIP2 and the 5EFL P or t Adapter Step 3 If IP routing is enabled on the system, you can assign an IP address and subnet mask to the interface with the ip address configuration subcommand, as in the following example: Router(config-int)# ip address 1.1.1.10 255.255.255.0 ...

  • Cisco Systems 10BASE-FL - page 21

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 21 Configuring the 5EFL Interfaces Using show Commands to Displa y Interface Inf or mation T o display information about a specific interface, use the show interfaces command with the interface type and port address in the format show interfaces [ type slot/port adapter/port ]. ...

  • Cisco Systems 10BASE-FL - page 22

    22 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration VIP2 and the 5EFL P or t Adapter The following e xample of the show interfaces ethernet slot/port adapter/port command sho ws all of the information specific to the first 5EFL interface port (interface port 0) in chassis slot 3, port adapter slot 1: Router# sh int e 3/ ...

  • Cisco Systems 10BASE-FL - page 23

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 23 Configuring the 5EFL Interfaces The show version (or show hardware ) command displays the configuration of the system hardware (the number of each interface processor type installed), the software v ersion, the names and sources of configuration files, and the boot images. ...

  • Cisco Systems 10BASE-FL - page 24

    24 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration VIP2 and the 5EFL P or t Adapter T o determine which type of port adapter is installed on a VIP2 in your system, use the show diag slot command. Specific port adapter information is displayed, as shown in the follo wing example of a 5EFL port adapter in chassis slot 1: ...

  • Cisco Systems 10BASE-FL - page 25

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 25 Cisco 7200 Series and the 5EFL Port Adapter Cisco 7200 Series and the 5EFL P or t Adapter The 5EFL port adapter is used in the Cisco 7200 series routers and can be installed in any of the av ailable port adapter slots. Figure 15 shows a Cisco 7206 with a 5EFL port adapter ins ...

  • Cisco Systems 10BASE-FL - page 26

    26 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Cisco 7200 Series and the 5EFL P or t Adapter Installing or Replacing a P or t Adapter in Cisco 7200 Ser ies Routers This section provides the standard procedures for installing or replacing port adapters in a Cisco 7200 series router . Depending on your circumstances, y ...

  • Cisco Systems 10BASE-FL - page 27

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 27 Installing or Replacing a Port Adapter in Cisco 7200 Series Routers Step 3 Grasp the handle on the port adapter and pull the port adapter from the midplane, about halfway out of its slot. If you are removing a blank port adapter , pull the blank port adapter from the port ada ...

  • Cisco Systems 10BASE-FL - page 28

    28 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Cisco 7200 Series and the 5EFL P or t Adapter Replacing a P or t Adapter Use the following standard procedure to install a ne w port adapter in a Cisco 7200 series router: Step 1 Attach an ESD-preventati ve wrist strap between you and an unfinished chassis surface. Step ...

  • Cisco Systems 10BASE-FL - page 29

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 29 Installing or Replacing a Port Adapter in Cisco 7200 Series Routers Step 7 Move the port adapter le ver to the locked position. Figure 19 shows the port adapter le ver in the locked position. Note If the port adapter le ver does not mo ve to the lock ed position, the port ada ...

  • Cisco Systems 10BASE-FL - page 30

    30 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Cisco 7200 Series and the 5EFL P or t Adapter Attaching 5EFL P or t Adapter Interf ace Cables On a single 5EFL port adapter , you can use up to five pairs of ST fiber -optic connections. The 5EFL port adapter is an end station device and not a repeater; you must connec ...

  • Cisco Systems 10BASE-FL - page 31

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 31 Configuring the 5EFL Interfaces Configuring the 5EFL Interfaces If you installed a ne w 5EFL port adapter or if you want to change the configuration of an existing interface, you must enter configuration mode using the configur e command. If you replaced a 5EFL port adapt ...

  • Cisco Systems 10BASE-FL - page 32

    32 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Cisco 7200 Series and the 5EFL P or t Adapter Figure 21 sho ws the port adapter slots and interface ports of a Cisco 7206. The port adapter slot numbers start with 1 and continue through 6 (slot 0 is always reserv ed for the Fast Ethernet port on the I/O controller—if ...

  • Cisco Systems 10BASE-FL - page 33

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 33 Configuring the 5EFL Interfaces Step 2 At the prompt, specify the first interface to configure by entering the subcommand interface , follo wed by the type ( ethernet ) and slot/interface (port adapter slot number and interface number). The example that follo ws is for the ...

  • Cisco Systems 10BASE-FL - page 34

    34 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Cisco 7200 Series and the 5EFL P or t Adapter Step 5 Display the running configuration file with the show running-config command. Display the configuration stored in NVRAM using the show startup-config command. V erify that the configuration is accurate for the sys ...

  • Cisco Systems 10BASE-FL - page 35

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 35 Configuring the 5EFL Interfaces The follo wing example of the show interfaces ethernet slot/port command shows all of the information specific to the first 5EFL interface port (interface port 0) in port adapter slot 2: Router# sh int e 2/0 Ethernet2/0 is administratively do ...

  • Cisco Systems 10BASE-FL - page 36

    36 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Cisco 7200 Series and the 5EFL P or t Adapter T o determine which type of port adapter is installed in your Cisco 7206, use the show diag slot command. Specific port adapter information is displayed, as shown in the follo wing example of a 5EFL port adapter in chassis s ...

  • Cisco Systems 10BASE-FL - page 37

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 37 Configuring the 5EFL Interfaces For complete descriptions of interface subcommands and the configuration options a vailable for Cisco 7200 series-related interfaces and functionality , refer to the publications listed in the section “If Y ou Need More Information” on pag ...

  • Cisco Systems 10BASE-FL - page 38

    38 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Cisco Connection Online Cisco Connection Online Cisco Connection Online (CCO) is Cisco Systems’ primary , real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services. A vailable 24 hours a day , 7 ...

  • Cisco Systems 10BASE-FL - page 39

    PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 39 Documentation CD-ROM This document is to be used in conjunction with the documents listed in the “If Y ou Need More Information” section. AccessPath, Any to An y , AtmDirector, the CCIE logo, CD-P AC, Centri, the Cisco Capital logo, CiscoLink , the Cisco Management Connec ...

  • Cisco Systems 10BASE-FL - page 40

    40 P A-5EFL Ether net 10BASE-FL P or t Adapter Installation and Configuration Documentation CD-ROM ...

Manufacturer Cisco Systems Category Network Card

Documents that we receive from a manufacturer of a Cisco Systems 10BASE-FL can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- 10BASE-FL manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems 10BASE-FL
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems 10BASE-FL.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems 10BASE-FL, service manual, brief instructions and user manuals Cisco Systems 10BASE-FL. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems 10BASE-FL.

A complete manual for the device Cisco Systems 10BASE-FL, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems 10BASE-FL by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems 10BASE-FL.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems 10BASE-FL - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems 10BASE-FL, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems 10BASE-FL, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems 10BASE-FL - which should help us in our first steps of using Cisco Systems 10BASE-FL
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems 10BASE-FL
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems 10BASE-FL in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems 10BASE-FL?

Use the form below

If you did not solve your problem by using a manual Cisco Systems 10BASE-FL, ask a question using the form below. If a user had a similar problem with Cisco Systems 10BASE-FL it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)