Manual Allied Telesis AT-GS950/8POE

68 pages 2.26 mb
Download

Go to site of 68

Summary
  • Allied Telesis AT-GS950/8POE - page 1

    613-000989 Rev. A Gigabit Ethernet WebSmart Switch AT-GS950/8POE ◆ Installation Guide ...

  • Allied Telesis AT-GS950/8POE - page 2

    Copyright © 2008 Allied Telesis, Inc. All rights reserved. No part o f this pub lication may be repro duced without prior wr itten permission from Al lied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Tele sis, Incorporated. All othe r product names, company nam es, logos or other designations mentioned herein a ...

  • Allied Telesis AT-GS950/8POE - page 3

    3 Electrical Safety and Emissions S tandards This product meets the following standards. RFI Emissions FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-3-3, C-TICK, CE EMC (Immunity) EN55024 Electrical Safety EN60950-1 (TUV), UL 60950-1 ( C UL US ), CSA-C22-2 No. 60950-1 ( C UL US ) U.S. Federal Communications Commission Radiated Energy Note: Thi ...

  • Allied Telesis AT-GS950/8POE - page 4

    4 T ranslated Safety S tatements Important: The  indicates that a translation of th e safety statement is available in a PDF document titled “Translated Safety St atements” ( 613-000990) posted on the Allied Telesis website a t www.alliedtelesis.com. ...

  • Allied Telesis AT-GS950/8POE - page 5

    5 Contents Preface ........ ................ ............. ................ ................ ............. ................. ................ ............ ............. ................ 11 Product Documentation ................ ................. ................ ................ ................ ................ ......... ....... ................ . ...

  • Allied Telesis AT-GS950/8POE - page 6

    Contents 6 Installing the Switch on a Wall ............ ................. ................ ................ ................ ................ ... ................ .......... 41 Resetting the Switch .. ................ ............. ................ ................ ................ ................ ............ ........... ............. ...... 43 C ...

  • Allied Telesis AT-GS950/8POE - page 7

    7 Figur es Figure 1: AT-GS950/8 POE Switch— Front and Back Panels ............. ....................................... ........... .......... ....... ............. 18 Figure 2: SFP Transc eiver ....................... .............. ........... .............. ........... .............. ........... .... ..... ........... ........... ............. ...

  • Allied Telesis AT-GS950/8POE - page 8

    Figures 8 ...

  • Allied Telesis AT-GS950/8POE - page 9

    9 Ta b l e s Table 1: Safety Symbols ................... ........... .............. ............ .............. ........... .............. ........ .................... ........... .............. .. 14 Table 2: IEEE 802.3af Class vs. Power Levels ....... .......................................... ................................. ... ........... .. ...

  • Allied Telesis AT-GS950/8POE - page 10

    Tables 10 ...

  • Allied Telesis AT-GS950/8POE - page 11

    11 Pr eface This guide contains the installat ion instructions for the AT-GS950/8POE Gigabit Ethernet WebSmart Switch. This preface con tains the following sections:  “Product Documenta tion” on p age 12  “S tarting a Management Session” on page 13  “Safety Symbols Used in this Document” o n page 14  “Where to Find W eb-ba ...

  • Allied Telesis AT-GS950/8POE - page 12

    Preface 12 Product Documentation For overview information about the softwa re features of the AT-GS950/ 8POE Gigabit Ethernet WebSmart Switch, refer to the AT-S101 Management Software User’s Guide ( P/N 613-000985). ...

  • Allied Telesis AT-GS950/8POE - page 13

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 13 Starting a Management Session For instructions that describe how to start a web management session o n an AT-GS950/8POE switch, refer to the AT-S101 Management Software User’s Guide . ...

  • Allied Telesis AT-GS950/8POE - page 14

    Preface 14 Safety Symbols Used in this Document This document uses the safety symbols defined in Table 1. T able 1. Safety Symbols Symbol Meaning Description Caution Performing or omi tting a specific action may result in equipment damage or loss of data. W arning Performing or omi tting a specific action may result in electrical shock. ...

  • Allied Telesis AT-GS950/8POE - page 15

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 15 Where to Find Web-based Guides The installation and user guides for all Allied Telesis products are available in portable document format (PDF) o n our web site at www.alliedtelesis.com . You can view the documents onlin e or download them onto a local workstation or server. ...

  • Allied Telesis AT-GS950/8POE - page 16

    Preface 16 Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales and corporate information . Online Support You can request technical sup port online by accessing t he Allied Telesis Knowledge Base: www.alliedteles is.com/support/kb.aspx . You can use the Knowledge Base to submit q ...

  • Allied Telesis AT-GS950/8POE - page 17

    17 Chapter 1 Overview This chapter describes the AT-GS950/8POE switch. This ch apter contains the following sections:  “Introduction” on p age 18  “10/100/1000Base-T T wisted Pair Port s” on pa ge 20  “Power over Ethernet” on pa ge 22  “Redundant T wisted Pair Port s” on p age 24  “SFP T ransceiver Slots” on pa ge ...

  • Allied Telesis AT-GS950/8POE - page 18

    Chapter 1: Ove rview 18 Introduction The AT-GS950/8POE switch features eight 10/100/100 0Base-T auto- negotiation ports, including four po rts with Power over Ethernet (PoE) capability , and two Gigabit ports. Figur e 1 shows the front and back pan els of the AT-GS950/8POE switch. This switch support s auto-negotiation and auto MDI/MDI-X on all loc ...

  • Allied Telesis AT-GS950/8POE - page 19

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 19  PoE feature conforms to IEEE802.3af Da ta T erminal Equipment (DTE)  Supports backpre ssure flow control at h alf-duplex and IEEE802.3x at full-duplex  Head of Line (HOL) blocking prevention  Web ma nagement with a pre-assigned IP address of 19 2.168.1.1  S tatus ...

  • Allied Telesis AT-GS950/8POE - page 20

    Chapter 1: Ove rview 20 10/100/1000Base-T Twisted Pair Ports This section describes the twisted pair port s on the switches. Connector Type The ports are 8-pin RJ-45 connectors that use four pins at 10 or 100 Mbps and all eight pins at 1000 Mbps. For the p in assignments, refer to “RJ-45 Twisted Pair Port Pinouts” on page 6 5. Speed A port’s ...

  • Allied Telesis AT-GS950/8POE - page 21

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 21 Cable Type The cabling requirements fo r a 10/100/1000Base-T port a re:  For 10 Mbps ope ration: S tandard TIA/EIA 568-B-compliant Cate gory 3 or better shielded or unshielded c abling with 100 ohm impe dance and a frequency of 16 MHz.  For 100 Mbps op eration: S tandard TI ...

  • Allied Telesis AT-GS950/8POE - page 22

    Chapter 1: Ove rview 22 Power over Ethernet The four of the twisted pair ports on the AT-GS9 50/8POE switch feature Power over Ethernet (PoE) which is a mechan ism for supplying power to network devices over the same twist ed pair cables used to carry network traffic. This feature can simplify network in stallation and maintenance by allowing you t ...

  • Allied Telesis AT-GS950/8POE - page 23

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 23 Power Budgeting The AT-GS950/8POE switch provides a maximum of 15.4 W of power per port on four of the eight ports for a total p ower consumption of 62 W, while at the same time furnishing sta ndard 10/100 Mbps Ethernet functio nality. The AT-GS950/8POE switch power management fu ...

  • Allied Telesis AT-GS950/8POE - page 24

    Chapter 1: Ove rview 24 Redundant Twisted Pair Ports Two of the twisted pair ports on the AT-GS950/8POE switch are paired with SFP slots. The twisted pair ports are identified wit h the letter “R” for “Redundant” as part of their number on t he faceplate of the unit. Ports 7 and 8 are the redundant ports. For combo ports 7 and 8, the copp e ...

  • Allied Telesis AT-GS950/8POE - page 25

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 25 SFP Transceiver Slots The AT-GS950/8POE switches feature slot s for two optional Gigabit Ethernet SFP transceivers that inte rconnect network devices ove r large distances using fiber optic cable. Fi gure 2 illustrates an SFP transceiver. Figure 2. SFP Transceiver Note For a list ...

  • Allied Telesis AT-GS950/8POE - page 26

    Chapter 1: Ove rview 26 LEDs The following sections describe the PoE, twisted p air port, SFP, and system LEDs. See Figure 3 for an illustration of the LEDs on an AT- GS950/8 POE switch. Figure 3. Port LEDs on an AT-GS950/8POE Switch PoE LEDs The AT-GS950/8POE switch has four PoE ports and f our corresponding PoE LEDs. The PoE LEDs signal a connect ...

  • Allied Telesis AT-GS950/8POE - page 27

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 27 10/100/1000Base- T Twisted Pair Port LEDs A twisted pair port has two LEDs labeled SPD (spee d) and L/A (link/ activity). The SPD LED indicates the port spee d. The L/A LED indicates the activity on a port. Both of t hese LEDs apply to ports 1 thro ugh 6 and 7R through 8R. Table ...

  • Allied Telesis AT-GS950/8POE - page 28

    Chapter 1: Ove rview 28 System LED There is one system LED on the front panel of the switch. It is the POWER LED which indicates wheth er or not the switch is rece iving power. See Table 6 for a description. T able 6. System LED LED St ate Description POWER Off The switch is not receiving power . Green The switch is receiving power . ...

  • Allied Telesis AT-GS950/8POE - page 29

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 29 Power Supply The AT-GS950/8POE switch has an in ternal power supply with a single AC power supply socket on the back panel which features au toswitch AC inputs. To power the switch on or o ff, connect or disconnect the power cord provided with the switch. Refer to “Technical Sp ...

  • Allied Telesis AT-GS950/8POE - page 30

    Chapter 1: Ove rview 30 Network Topologies This section describes the network topologies o f the AT-GS950/8POE Gigabit Ethernet WebSmart Switch : power workgroup and collapsed backbone. Both types of topologies are described in the following sections. Power Workgroup Topology The topology shown in Figure 4 is co mmonly referred to as a power workgr ...

  • Allied Telesis AT-GS950/8POE - page 31

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 31 Figure 5. Collapsed Backbone—Hub Topology AT- G S 950/ 8 POE 8 Port 10/100/1000M b p s + 2 S FP Com b o We bS m a rt S witch S FP S FP CLASS 1 LASER PRODUCT 12 3 45 6 7 R 7 8 8 R POWER RE S ET 12 3 45 6 7 R 8 R 7 8 POE 100/1000Ba s e-X PORT ACTIVITY ACT 1000 LINK 100 LINK ACT A ...

  • Allied Telesis AT-GS950/8POE - page 32

    Chapter 1: Ove rview 32 ...

  • Allied Telesis AT-GS950/8POE - page 33

    33 Chapter 2 Installing the Hardwar e This chapter provides procedures to install an AT-GS950/8POE switch on a desktop, in a rack, and on a wall as well as how to reset the switch. The chapter contains the following sections:  “Reviewing Safety Precautions” on p age 34  “Selecting a Site for the Switch” on p age 36  “Unpacking a ...

  • Allied Telesis AT-GS950/8POE - page 34

    Chapter 2: Inst alling the Hardware 34 Reviewing Safety Precautions Please review the following safety pr ecautions before you begin to install the switches or any of their components. Note The  indicates that a translation of the safety state ment is available in a PDF document titled “Tra nslated Safety Statements” (613-000990) posted on t ...

  • Allied Telesis AT-GS950/8POE - page 35

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 35 All Countries: Install produ ct in accordance with local and National Electrical Codes.  E8 Circuit Overloading: Consideratio n should be given to the connection of the equipment to the sup ply circuit and the ef fect that overloading of circuit s might have on over current pr ...

  • Allied Telesis AT-GS950/8POE - page 36

    Chapter 2: Inst alling the Hardware 36 Selecting a Site for the Switch Observe the following requirements when choosing a site for your switch:  If you plan to inst all the switch in an equipment rack, ensure that th e rack is secured safely and that it will not tip over . Devices in a rack should be insta lled st arting at the bottom, with the ...

  • Allied Telesis AT-GS950/8POE - page 37

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 37 Unpacking a Switch To unpack a switch, perform the following procedure: 1. Remove all components from the shipping package s. Note Store the packaging material in a safe location. You must use the original shipping material if you need t o return the unit to Allied Telesis. 2. Pl ...

  • Allied Telesis AT-GS950/8POE - page 38

    Chapter 2: Inst alling the Hardware 38 Installing the Switch on a Desktop You can install the AT-GS950/ 9POE switch on a desktop, in a rack, or on a wall. To install a switch on a desktop, perform the fo llowing procedure: 1. Remove all of the equipment from the package a nd store the packaging material in a safe place. 2. Turn the switch over and ...

  • Allied Telesis AT-GS950/8POE - page 39

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 39 Installing the Switch in an Equipment Rack To install the switch in a stand ard 19-inch rack, perform the following procedure: Note Steps 1, 2, and 3 are optional. The se steps provide instructions on how to remove the snap-on p lastic feet from the bottom of a switch. You can le ...

  • Allied Telesis AT-GS950/8POE - page 40

    Chapter 2: Inst alling the Hardware 40 Figure 8. Attaching Rack-Mount Brackets 5. Install the second rack-mo unt bracket on the other sid e of the switch with the four remaining screws. 6. Mount the switch in a 19-inch rack using standard screws (not provided), as shown in Figure 9. Figure 9. Mounting the Switch in a Rack Note For cabling informati ...

  • Allied Telesis AT-GS950/8POE - page 41

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 41 Installing the Switch o n a Wall To install the switch on a wall, pe rform the following procedure: Note Steps 1, 2, and 3 are optional. The se steps provide instructions on how to remove the snap-on p lastic feet from the bottom of a switch. You can leave the feet attached to th ...

  • Allied Telesis AT-GS950/8POE - page 42

    Chapter 2: Inst alling the Hardware 42 5. Place the switch on the wall. Then mount the switch using the four #10-32 Phillips screws which are shipped with t he product as shown in Figure 11. Figure 11. Attaching the switch to the wa ll Note For cabling information, see Chapter 3, “Cabling the Network Ports” on page 45. 1 3 5 3 AT -GS950/8POE 8 ...

  • Allied Telesis AT-GS950/8POE - page 43

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 43 Resetting the Switch You may need to reset the switch after upgrading the firmware or after you have made a configuration change that requires resetting the switch to activate the change. To reset the AT-GS950/8POE switch, perform the followin g procedure: 1. Locate the RESET but ...

  • Allied Telesis AT-GS950/8POE - page 44

    Chapter 2: Inst alling the Hardware 44 ...

  • Allied Telesis AT-GS950/8POE - page 45

    45 Chapter 3 Cabling the Network Ports This chapter contains gui delines and instructio ns for attaching network cables to an AT-GS950/8POE switch . This chapter contains the fo llowing sections:  “Cable S pecifications” on page 46  “Cabling the Switch” on page 48  “Connecting an RJ-45 Cable” on p age 49  “Installing Optio ...

  • Allied Telesis AT-GS950/8POE - page 46

    Chapter 3: Cablin g the Network Ports 46 Cable Specifications This section provides information a bout th e twisted pair and SFP cables. Twisted Pair Cable Specifications Table 7 lists the cabling specificati ons for the 10/100/1000Base-T twisted pair ports. Note The auto-MDI/MDI-X feature on the twisted pair ports auto matically configures the MDI ...

  • Allied Telesis AT-GS950/8POE - page 47

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 47 Note A 10/100/1000Base-T twisted pair port must be set to Auto- Negotiation to operate at 1000 Mbp s. You cannot manually set th e speed of a twisted pair port to 1000 Mb ps. Optional Transceiver Cable Specifications The cable specifications for an opt ional SFP transceiver can b ...

  • Allied Telesis AT-GS950/8POE - page 48

    Chapter 3: Cablin g the Network Ports 48 Cabling the Switch Observe the following guidelines when c onnecting a twisted pair or fiber optic cables to ports on the switch:  The connector on the cable should fit snugly int o the port on the switch. The tab on th e connector should lock the connector into place.  The twisted pair port s on the s ...

  • Allied Telesis AT-GS950/8POE - page 49

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 49 Connecting an RJ-45 Cable There are eight RJ-45 ports on the AT-GS950/8POE switch. Ports 1 through 4 are PoE ports To connect an RJ-45 cable to th e switch, perform the following procedure: 1. Connect an RJ-45 cable to a twisted-pair port. See Figure 13. Figure 13. Connecting an ...

  • Allied Telesis AT-GS950/8POE - page 50

    Chapter 3: Cablin g the Network Ports 50 Installing Optional Transceivers Review the following guidelines before installing an optional SFP transceiver in a switch:  A transceiver can be hot-swapped; the switch can be powered on when you install it. Howeve r , you should always disconnect the cables before removing a transceive r .  Y ou must ...

  • Allied Telesis AT-GS950/8POE - page 51

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 51 2. Remove the transceiver from its shipping containe r and store the packaging material in a safe loca tion. 3. Position the transceiver with the label facing up. 4. Slide the transceiver into the slot until it clicks into place . See Figure 15. Figure 15. Installing an SFP Trans ...

  • Allied Telesis AT-GS950/8POE - page 52

    Chapter 3: Cablin g the Network Ports 52 7. Insert the fiber optic cable into the SF P transceiver. See Figure 17. Figure 17. Inserting the Fiber Optic Cable 8. Repeat this procedure to install another SFP transceiver. For SFP optical and cabling specific ations, consult the do cumentatio n shipped with the module. 1 3 50 SFP SFP CLASS 1 LAS ER PRO ...

  • Allied Telesis AT-GS950/8POE - page 53

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 53 Powering on a Switch To power on a switch, perform the followin g procedure: 1. Plug the power cord into the AC powe r connector on the back panel of the unit, as shown in Figure 18. Figure 18. Connecting the AC Power Cord 2. Plug the other end of the power cord into a wall ou tl ...

  • Allied Telesis AT-GS950/8POE - page 54

    Chapter 3: Cablin g the Network Ports 54 ...

  • Allied Telesis AT-GS950/8POE - page 55

    55 Chapter 4 T r oubleshooting This chapter contains informat ion about how to troubleshoot a switch in the event a problem occurs. Sections in the cha pter include:  “Power LED is Off” on p age 56  “T wisted Pair Port Link LED is Of f” on p age 57  “Port PoE LED is not Solid Green” on p age 58  “Port PoE LED is Off” on ...

  • Allied Telesis AT-GS950/8POE - page 56

    Chapter 4: Tro ubleshooting 56 Power LED is Off Check the PWR LED on the front of the switch. If t he LED is off, indicating that the unit is not receiving power, do the following:  Make sure the power cord is securely connected to the p ower source and to the AC connector on the back p anel of the switch.  V erify that the power outlet has p ...

  • Allied Telesis AT-GS950/8POE - page 57

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 57 Twisted Pair Port Link LED is Off When a twisted pair port on the switch is connected to a properly operating end node, the L/A LED f or the port should be on . If a L/A Link LED is off, do the following: Note A 1000Base-T connection can take from five to ten seconds to establish ...

  • Allied Telesis AT-GS950/8POE - page 58

    Chapter 4: Tro ubleshooting 58 Port PoE LED is not Solid Green On those ports that are supplyin g PoE power to another device, verify that the port PoE LED is solid green. If the LED is not solid green, do the following:  V erify that the connected device is no more than 10 0 feet from the switch.  If the port PoE LED is solid amber , then th ...

  • Allied Telesis AT-GS950/8POE - page 59

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 59 Port PoE LED is Off If the PoE LED is off, then do both of the fo llowing:  V erify that the twisted pa ir cable is securely connected to t he port on the switch and to the port on the conne cted device; and  V erify that the connected device conforms to IEEE 802.1af Note A ...

  • Allied Telesis AT-GS950/8POE - page 60

    Chapter 4: Tro ubleshooting 60 SFP LED is Off When a fiber optic port on the switch is co nnected to a properly operating end node, the Link LED for the port should be on. If a Link LED is off, d o the following:  V erify that the end node connected to the port is powered ON and is operating properly .  Check that the fiber optic cable is sec ...

  • Allied Telesis AT-GS950/8POE - page 61

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 61 Transceiver is Installed but the Status is “Not Present” If a SFP transceiver is installed in a transceiver slot but the Uplink Information menu in the system software int erface displays “Not Present” for that port, do the following:  V erify that the transceiver is c ...

  • Allied Telesis AT-GS950/8POE - page 62

    Chapter 4: Tro ubleshooting 62 Switch Functions Intermittently If a switch functions intermittently, check the system hardware statu s through the management interface :  Note the current volt age for the power supp ly compared to th e optimum rating.  V erify that the system temperature is within the operating range. ...

  • Allied Telesis AT-GS950/8POE - page 63

    63 Appendix A T echnical Specifications Physical Specifications Dimensions (H x W x D): 4.32 x 33 x 23.5 cm (1.7 x 12.99 x 9.07 in.) Weight: 2.54 kg (5.60 lb.) Recommended Minimum Ventilation on All Sides: 10 cm (4.0 in.) Environmental Specifications Operating Temperature: 0° C to 40° C (32° F to 104° F) Storage Temperature: -25° C to 70° C ( ...

  • Allied Telesis AT-GS950/8POE - page 64

    Appendix A: Technica l Specifications 64 Certifications EMI (Emissions): FCC Class A, ICES-003 Class A, EN55022 Class A, EN61000-3-2, EN61000-3-3, C-TICK, CE EMC (Immunity): EN55024 Electrical and Laser Safety: EN60950-1 (TUV), UL 60950-1 ( C UL US ), CSA-C22-2 No. 60950-1 ( C UL US) Quality and Reliability (MTBF): 100,000 hrs. Compliance Marks: CE ...

  • Allied Telesis AT-GS950/8POE - page 65

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 65 RJ-45 Twisted Pair Port Pinouts Figure 19 illustrates the pin lay out of an RJ-45 connector and port. Figure 19. RJ-45 Connector and Port Pin L ayout Table 8 lists the pin sig nals when a port is operating in t he MDI configuration at 10 or 100 Mbp s. Table 9 lists the pin sig na ...

  • Allied Telesis AT-GS950/8POE - page 66

    Appendix A: Technica l Specifications 66 Table 10 lists the pin signals when a p ort operating at 1000 Mb ps. T able 10. Pin Signals - 1000 Mbp s Pinout Pair 1P a i r 1 + 2P a i r 1 - 3P a i r 2 + 4P a i r 3 + 5P a i r 3 - 6P a i r 2 - 7P a i r 4 + 8P a i r 4 - ...

  • Allied Telesis AT-GS950/8POE - page 67

    AT-GS950/8POE Gigabit Ethernet WebSmart Switc h Installation Guide 67 RJ-45 Style Serial Terminal Port Pinouts Table 11 lists the pin signals on the RJ-45 style serial terminal port. T able 1 1. RJ-45 S tyle Serial T erminal Port Pin Signals Pin Signal 4 Data Carrie r Detect 3 T ransmit Data 6R e c e i v e D a t a 7 Data Set Ready 5 Ground 2 Data T ...

  • Allied Telesis AT-GS950/8POE - page 68

    Appendix A: Technica l Specifications 68 ...

Manufacturer Allied Telesis Category Switch

Documents that we receive from a manufacturer of a Allied Telesis AT-GS950/8POE can be divided into several groups. They are, among others:
- Allied Telesis technical drawings
- AT-GS950/8POE manuals
- Allied Telesis product data sheets
- information booklets
- or energy labels Allied Telesis AT-GS950/8POE
All of them are important, but the most important information from the point of view of use of the device are in the user manual Allied Telesis AT-GS950/8POE.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Allied Telesis AT-GS950/8POE, service manual, brief instructions and user manuals Allied Telesis AT-GS950/8POE. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Allied Telesis AT-GS950/8POE.

A complete manual for the device Allied Telesis AT-GS950/8POE, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Allied Telesis AT-GS950/8POE by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Allied Telesis AT-GS950/8POE.

A complete Allied Telesis manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Allied Telesis AT-GS950/8POE - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Allied Telesis AT-GS950/8POE, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Allied Telesis AT-GS950/8POE, that we can find in the current document
3. Tips how to use the basic functions of the device Allied Telesis AT-GS950/8POE - which should help us in our first steps of using Allied Telesis AT-GS950/8POE
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Allied Telesis AT-GS950/8POE
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Allied Telesis AT-GS950/8POE in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Allied Telesis AT-GS950/8POE?

Use the form below

If you did not solve your problem by using a manual Allied Telesis AT-GS950/8POE, ask a question using the form below. If a user had a similar problem with Allied Telesis AT-GS950/8POE it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)