Manual Cisco Systems 6200

32 pages 0.35 mb
Download

Go to site of 32

Summary
  • Cisco Systems 6200 - page 1

    CHAPTER Cisco 6200 User Guide 1-1 1 Hardw are Descr iption This chapter provides an o vervie w of the Cisco 6200 advanced digital subscriber line access multiplex er (DSLAM) and describes the system’ s hardware components. The chapter is arranged as follows: • Cisco DSL Product Family on page 1-1 • Cisco 6200 Chassis on page 1-2 • Network T ...

  • Cisco Systems 6200 - page 2

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-2 The Cisco DSL family also includes a Frame Relay IDSL multiplex er , a service selection gatew ay , the Cisco 605 card, the Cisco 6100 DSLAM, and an A TM switch to aggregate Cisco 6200 traf fic. 1.2 Cisco 6200 Chassis This section describes the chassis that houses the Cisco 6200 ...

  • Cisco Systems 6200 - page 3

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-3 Figure 1-1 Cisco 6200 Chassis, Front Vie w 1.2.2 Bac kplane Located behind the module compartment, the backplane provides the follo wing services: • Interconnects the MPC, NTC, and SLCs • Connects the SLCs with the subscribers (local loops) or the PO TS splitter • Distribute ...

  • Cisco Systems 6200 - page 4

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-4 Figure 1-2 Cisco 6200 Chassis, Rear View Primar y (A) and Secondar y (B) H-Buses The backplane’ s primary and secondary H-buses (horizontal buses) link the MPC, NTC, and SLCs. In this release, the primary bus carries all traf fic. The buses operate at 160 Mbps total throughput. ...

  • Cisco Systems 6200 - page 5

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-5 Connections to PO TS Splitters or T elephone Lines On the inner surface of the backplane, the upper and lo wer SLC connectors connect the SLC in the corresponding slot (5 to 14) with unshielded twisted pair (UTP) lines. These lines connect to an external PO TS splitter, and from t ...

  • Cisco Systems 6200 - page 6

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-6 A uxiliar y P or t J40, a 9-pin female connector on the Cisco 6200 backplane, is an EIA/TIA-232 (RS-232) serial port connecting to the management processor card (MPC). J40 is an auxiliary craft port that can be used to connect de vices such as terminals, modems, or laptop computer ...

  • Cisco Systems 6200 - page 7

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-7 The following fixtures are present on the front panel of each PEM: • A green LED that comes on to indicate that –48 VDC power is a v ailable to the chassis • A circuit breaker Note T o turn of f a Cisco 6200 that has two PEMs, you must flip the circuit breakers on both PEM ...

  • Cisco Systems 6200 - page 8

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-8 T able 1-1 Cisco 6200 DSLAM Specifications T able 1-2 Standards and Certifications Specification Description Components 14-slot card compartment Backplane Fan compartment Power module compartment Power input Dual inputs, each –48 VDC T ested voltages: –48V and –57V T oler ...

  • Cisco Systems 6200 - page 9

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-9 1.3 Netw ork T runk Car ds (NTCs) This section describes the OC-3c and STM-1 network trunk cards (NTCs). The NTC module resides in slot 1 of the Cisco 6200 chassis. 1.3.1 What is the NTC OC-3? The NTC is a service interface module that concentrates the data traf fic from all Cisc ...

  • Cisco Systems 6200 - page 10

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-10 Figure 1-5 NTC OC-3 Application The optical interface performs the optical-to-electrical and electrical-to-optical con versions. Its other tasks include clock recov ery , o verhead processing, cell delineation, and diagnostic information retriev al. The upstream data transfer uni ...

  • Cisco Systems 6200 - page 11

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-11 The fiber optic communication channels in the single-mode OC-3c card (NTC OC3-SM) operate with laser energy , which can be harmful, especially to the eyes. During normal operation this ener gy is confined to the cable and presents no danger . T o avoid injury when you are conne ...

  • Cisco Systems 6200 - page 12

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-12 T able 1-3 LEDs on the NTC OC-3 LED Color Condition Indicated PO WER Green The module is receiving po wer . READ Y Green Y ellow Off The NTC is experiencing no problems. The NTC failed its po wer-on self test; it has a hardware problem. Refer to Chapter 7, “T roubleshooting. ? ...

  • Cisco Systems 6200 - page 13

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-13 1.3.3 NTC OC-3 Specifications T able 1-4 lists the physical and electrical specifications of the NTC. T able 1-4 NTC OC-3 Specifications 1.3.4 What is the NTC STM-1? The NTC STM-1 is a service interface module that concentrates the data traf fic from all Cisco 6200 subscriber ...

  • Cisco Systems 6200 - page 14

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-14 The NTC STM-1 also transmits upstream data back to the service provider via A TM on the STM-1 physical layer . The Cisco 6200 uses a fixed mapping of permanent virtual channels (PVCs) between trunk and subscriber ports. This means that no configuration of these circuits is requ ...

  • Cisco Systems 6200 - page 15

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-15 The upstream data transfer unit recei ves data via a 16-bit parallel input from the internal bus on the node’ s backplane. A TM cells are receiv ed from a subscriber line card (SLC) channel only after that channel has won access to the upstream data b us from the other contendi ...

  • Cisco Systems 6200 - page 16

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-16 Figure 1-8 NTC STM-1 Faceplates LED Indicators T able 1-5 describes the LEDs on the faceplate of the NTC STM-1. POWER A C T I V E NTC STM1-SM READY PRIME SEC A TD RD POWER A C T I V E NTC STM1-MM READY PRIME SEC A TD RD 14271 Card status LEDs T ransmit and receive LEDs Reset swit ...

  • Cisco Systems 6200 - page 17

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-17 T able 1-5 LEDs on the NTC STM-1 1.3.6 NTC STM-1 Specifications T able 1-6 lists the physical and electrical specifications of the NTC STM-1. LED Color Condition Indicated PO WER Green The module is receiving po wer . READ Y Green Y ellow Off The NTC is experiencing no problems ...

  • Cisco Systems 6200 - page 18

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-18 T able 1-6 NTC STM-1 Specifications 1.4 Management Pr ocessor Card (MPC) The Cisco 6200 is controlled and managed by the MPC. 1.4.1 Functional Description The MPC performs management and storage tasks for the Cisco 6200 DSLAM. The MPC provides • The Cisco IOS command line inte ...

  • Cisco Systems 6200 - page 19

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-19 The MPC runs a version of Cisco IOS software that is designed for DSL multiple xing. At startup, the MPC loads program software and configuration data from NVRAM, from a server on the network, or from a Flash card in one of its PCMCIA slots. The MPC then pro vides boot images to ...

  • Cisco Systems 6200 - page 20

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-20 Console P or t The console port on the MPC is a serial EIA/TIA-232 port with an RJ-45 connector . See Appendix A, “Pin Assignments, ” for pinouts. PCMCIA Slots and Ejection Buttons The MPC provides two slots for PCMCIA Flash memory cards. PCMCIA cards store system software an ...

  • Cisco Systems 6200 - page 21

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-21 1.4.3 MPC Specifications T able 1-8 lists the physical and electrical specifications of the MPC. T able 1-8 MPC Specifications Specification Description External Interfaces • EIA/TIA-232 console port • 10BaseT Ethernet management port Internal Hardware • MIPS R V4640 pr ...

  • Cisco Systems 6200 - page 22

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-22 1.5 Subscriber Line Car d (SLC) This section describes the CAP and DMT versions of the subscriber line card (SLC). A Cisco 6200 chassis can hold up to 10 SLC modules. Note All the SLCs in a Cisco 6200 chassis should be of the same type. The mixture of CAP and DMT cards in a singl ...

  • Cisco Systems 6200 - page 23

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-23 In the do wnstream direction, 11 rates are av ailable ranging from 640 kbps to 7.168 Mbps. In the upstream direction, 9 rates are av ailable, ranging from 91 kbps to 1.088 Mbps. The modems on the CAP SLC train in sequence, first downstream, then upstream. Each modem first acqui ...

  • Cisco Systems 6200 - page 24

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-24 1.5.2 SLC 8CAP: Ph ysical Description Up to 10 SLCs can be installed in a Cisco 6200 cabinet. The cabinet slots assigned to the SLCs are slot 5 through slot 14. The CAP SLC’ s faceplate is labeled SCL 8CAP . The faceplate (Figure 1-11) includes the fixtures discussed in the fo ...

  • Cisco Systems 6200 - page 25

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-25 T able 1-9 SLC 8CAP LEDs LED Color Condition Indicated PO WER Green The SLC is receiving po wer . READ Y Green Y ellow Off The SLC is experiencing no problems. At least one port on the SLC is in line test mode. The SLC is not communicating with the MPC. This is the case when • ...

  • Cisco Systems 6200 - page 26

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-26 1.5.3 SLC 8CAP Specifications T able 1-10 lists the physical and electrical specifications of the CAP SLC (SLC 8CAP). T able 1-10 SLC 8CAP Specifications Specification Description Subscriber ports 8 per card T ransmission speeds Downstream: up to 7 Mbps Upstream: up to 1 Mbps ...

  • Cisco Systems 6200 - page 27

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-27 1.5.4 What is the SLC 8DMT? The eight-port DMT version of the SLC (SLC 8DMT) is a hot-swappable line module that pro vides data communication between the Cisco 6200 node and up to eight subscribers. Modems on the SLC 8DMT use discrete multitone (DMT) modulation, a common method f ...

  • Cisco Systems 6200 - page 28

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-28 In the upstream direction, the SLC recei ves ADSL signals from a PO TS splitter and demodulates the DMT -modulated signal. Then the SLC channel contends with the other SLC channels for the upstream data bus. T wo priority le vels are av ailable. For the first Cisco 6200 release, ...

  • Cisco Systems 6200 - page 29

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-29 • Number of upstream cells receiv ed with in valid header checksum • Number of errored seconds (this is the number of seconds in which at least one DMT -layer CRC error , loss of signal, or sev erely errored frame is observed), both upstream and do wnstream In addition, the S ...

  • Cisco Systems 6200 - page 30

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-30 Figure 1-13 SLC 8DMT Faceplate Reset Switch The reset switch is recessed behind the faceplate to a void accidental acti vation. It is not for customer use. LED Indicators T able 1-11 describes the LEDs on the faceplate of the SLC. 13067 SLC 8DMT PORTS 1 2 3 4 5 6 7 POWER READY PR ...

  • Cisco Systems 6200 - page 31

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-31 T able 1-11 SLC 8DMT LEDs LED Color Condition Indicated PO WER Green The SLC is receiving po wer . READ Y Green Y ellow Off The SLC is experiencing no problems. At least one port on the SLC is in line test mode. The SLC is not communicating with the MPC. This is the case when • ...

  • Cisco Systems 6200 - page 32

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-32 1.5.6 SLC 8DMT Specifications T able 1-12 lists the physical and electrical specifications of the SLC 8DMT . T able 1-12 SLC 8DMT Specifications Specification Description Subscriber ports 8 per card T ransmission speeds Downstream: up to 8.032 Mbps Upstream: up to 864 kbps Lo ...

Manufacturer Cisco Systems Category Server

Documents that we receive from a manufacturer of a Cisco Systems 6200 can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- 6200 manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems 6200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems 6200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems 6200, service manual, brief instructions and user manuals Cisco Systems 6200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems 6200.

A complete manual for the device Cisco Systems 6200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems 6200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems 6200.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems 6200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems 6200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems 6200, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems 6200 - which should help us in our first steps of using Cisco Systems 6200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems 6200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems 6200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems 6200?

Use the form below

If you did not solve your problem by using a manual Cisco Systems 6200, ask a question using the form below. If a user had a similar problem with Cisco Systems 6200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)