English dropdown-ico

Manual Cisco Systems 7304

22 pages 0.26 mb
Download

Go to site of 22

Summary
  • Cisco Systems 7304 - page 1

    CHAPTER 13-1 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 13 Configuring the 2-Port and 4-Port T3/E3 SPAs This chapter provides information about conf iguring the 2-Port and 4-Port T3/E3 Shared Port Adapters (SP As) on the Cisco 7304 router. It includes the following sections: • Conf igur ...

  • Cisco Systems 7304 - page 2

    13-2 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Required Configuration Tasks This section lists the required conf iguration steps to conf igure the 2-Port or 4-Port T3/E3 SP A. Some of the required conf iguration ...

  • Cisco Systems 7304 - page 3

    13-3 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configure the Interface T o set the ip address for the 2-Port or 4-Port T3/E3 SP A, complete these steps: Verifying Controller Configuration Use the show controllers ...

  • Cisco Systems 7304 - page 4

    13-4 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks 0 C-bit Coding Violation, 0 P-bit Err Secs, 0 P-bit Sev Err Secs, 0 Sev Err Framing Secs, 0 Unavailable Secs, 24750 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit ...

  • Cisco Systems 7304 - page 5

    13-5 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Serial6/0/0.16 is up, line protocol is up Hardware is SPA-4T3E3 Internet address is 110.1.1.2/24 MTU 4470 bytes, BW 44210 Kbit, DLY 200 usec, reliability 255/255, tx ...

  • Cisco Systems 7304 - page 6

    13-6 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configuring Data Service Unit Mode Conf igure the SP A to connect with customer premise Data Service Units (DSUs) by setting the DSU mode. Subrating a T3 or E3 inter ...

  • Cisco Systems 7304 - page 7

    13-7 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Verifying DSU Mode Use the show controllers serial command to display the DSU settings: router# show controllers serial 6/0/0 Serial6/0/0 - Framing is c-bit, Clock S ...

  • Cisco Systems 7304 - page 8

    13-8 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks 0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs Data in Interval 1: 0 Line Code Violations, 0 P-bit Coding Violation 0 C-bit Coding Violation 0 P-bit ...

  • Cisco Systems 7304 - page 9

    13-9 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Router(conf ig-if)# mdl [ string { eic | f ic | generator | lic | pf i | port | unit } string }] | [ transmit { idle-signal | path | test-signal }] Conf igures the M ...

  • Cisco Systems 7304 - page 10

    13-10 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Verifying MDL Use the show controllers serial command to display the MDL settings: router# show controllers serial 6/0/0 Serial6/0/0 - Framing is c-bit, Clock Sourc ...

  • Cisco Systems 7304 - page 11

    13-11 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Scrambling can pre vent some bit patterns from being mistakenly interpreted as alarms by switches placed between the Data Service Units (DSUs). T o conf igure scram ...

  • Cisco Systems 7304 - page 12

    13-12 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configuring Framing Framing is used to synchronize data transmission on the line. Framing allo ws the hardware to determine when each packet starts and ends. T o co ...

  • Cisco Systems 7304 - page 13

    13-13 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configuring Encapsulation When traff ic crosses a W AN link, the connection needs a Layer 2 protocol to encapsulate traf f ic. T o set the encapsulation method, use ...

  • Cisco Systems 7304 - page 14

    13-14 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configuring Cable Length The cablelength command compensates for the loss in decibels based on the distance from the device to the f irst repeater in the circuit. A ...

  • Cisco Systems 7304 - page 15

    13-15 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configuring Invert Data Delays between the TE clock and data transmission indicate that the transmit clock signal might not be appropriate for the interface rate an ...

  • Cisco Systems 7304 - page 16

    13-16 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Verify TTB Settings Use the show controllers serial command to display the TTB settings for the interface: router# show controllers serial 6/0/0 Serial6/0/0 - Frami ...

  • Cisco Systems 7304 - page 17

    13-17 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Verifying the Interface Configuration Saving the Configuration T o sa ve your running conf iguration to nonv olatile random-access memory (NVRAM), use the following command in pri vile ...

  • Cisco Systems 7304 - page 18

    13-18 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Verifying the Interface Configuration Monitoring Per-Port Interface Statistics T o f ind detailed status and statistical information on a per-port basis for the 2-Port or 4-Port T3/E3 ...

  • Cisco Systems 7304 - page 19

    13-19 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Examples No FEAC code is being received MDL transmission is disabled Configuration Examples This section includes the following conf iguration examples: • DSU Conf igur ...

  • Cisco Systems 7304 - page 20

    13-20 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Examples Router(config-if)# mdl transmit path Router(config-if)# mdl transmit idle-signal Router(config-if)# mdl transmit test-signal Scrambling Configuration Example The ...

  • Cisco Systems 7304 - page 21

    13-21 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Examples ! Specify the cable length ! Router(config-if)# cablelength 200 Invert Data Configuration Example The following e xample enables in vert data: ! Enter global con ...

  • Cisco Systems 7304 - page 22

    13-22 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Examples ...

Manufacturer Cisco Systems Category Network Router

Documents that we receive from a manufacturer of a Cisco Systems 7304 can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- 7304 manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems 7304
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems 7304.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems 7304, service manual, brief instructions and user manuals Cisco Systems 7304. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems 7304.

Similar manuals

A complete manual for the device Cisco Systems 7304, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems 7304 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems 7304.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems 7304 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems 7304, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems 7304, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems 7304 - which should help us in our first steps of using Cisco Systems 7304
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems 7304
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems 7304 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems 7304?

Use the form below

If you did not solve your problem by using a manual Cisco Systems 7304, ask a question using the form below. If a user had a similar problem with Cisco Systems 7304 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)