-
Grizzly H5503 - page 1
COPYRIGHT © JUNE, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN CHINA ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONF ...
-
Grizzly H5503 - page 2
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonr ...
-
Grizzly H5503 - page 3
H5503 14 Gauge Swivel Head Shears -1 - For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentia ...
-
Grizzly H5503 - page 4
H5503 14 Gauge Swivel Head Shears -2 - 10. USE PROPER EXTENSION CORD for the tool. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and o ...
-
Grizzly H5503 - page 5
H5503 14 Gauge Swivel Head Shears -3 - INTRODUCTION Commentary Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzl ...
-
Grizzly H5503 - page 6
H5503 14 Gauge Swivel Head Shears -4 - OPERATION Test Run Operating these shears can propel objects into the air, causing immedi- ate eye damage. To protect yourself, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. To protect your hands, always wear leather hand pro- tecti ...
-
Grizzly H5503 - page 7
H5503 14 Gauge Swivel Head Shears -5 - Cutting Trigger Lock To start a cutting operation: 1. Choose a work space that is ade- quate for the size of material to be cut and secure the workpiece. 2. Layout the cut lines in your material with a scribe or writing utensil. 3. Start cutting at the edge of the work- piece as shown in FIgure 3 . You must ap ...
-
Grizzly H5503 - page 8
H5503 14 Gauge Swivel Head Shears -6 - Changing Blades To change the blades: 1. Make sure the tool is disconnected from the power supply. 2. Unscrew the three cap screws in the head of the shears and set them aside. 3. Remove the head assembly from the main body of the shear by pulling it forward ( Figure 5 ). Figure 5. Shear head removal. 4. Remov ...
-
Grizzly H5503 - page 9
H5503 14 Gauge Swivel Head Shears -7 - Lubrication Always disconnect the power from the tool before performing any mainte- nance . • Place one drop of light machine oil in the shear jaws (as shown in Figure 6 ) before every use. Wipe off any excess oil to avoid dust build-up. Figure 6. Lubricating shear. MAINTENANCE Figure 7. Bearing lubrication ...
-
Grizzly H5503 - page 10
H5503 14 Gauge Swivel Head Shears -8 - Cleaning Shear Use a good solvent to clean the jaw assembly of the shear. Avoid getting sol- vent on the plastic body of the shear as it may damage the plastic. Always be sure that the shear is dry before using it again. Do not allow dust, chips, sand, etc. into the air vent holes. This could lead to motor fai ...
-
Grizzly H5503 - page 11
H5503 14 Gauge Swivel Head Shears -9 - NOTES ...
-
Grizzly H5503 - page 12
H5503 14 Gauge Swivel Head Shears -10 - 1 3 4 5 8 10 11 2 35 6 7 9 23 24 25 26 27 21 20 16 14 13 12 29 15 19 18 17 34 32 36 30 31 33 ...
-
Grizzly H5503 - page 13
H5503 14 Gauge Swivel Head Shears -11 - DESCRIPTION REF PART # 1 PH5503001 BODY COVER 2 PH5503002 BEARING STAND 3 PH5503003 STATOR 4 PW05M FLAT WASHER 4MM 5 PH5503005 SPECIAL TAP SCREW M4-X 62 6 P607 BEARING 607Z 7 PH5503007 FAN COVER 8 PH5503008 ROTOR 9 PH5503009 BEARING STAND 10 PH5503010 GEAR BOX 11 PH5503011 SEALING MAT 12 P608ZZ BEARING 608ZZ ...
-
Grizzly H5503 - page 14
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole written warranty and any and all wa ...
-
Grizzly H5503 - page 15
Name __________________________________________________________ Street __________________________________________________________ City ____________________ State ________ Zip _________ Phone Number ____________ E-Mail ___________________ FAX ____________ Model # ___________________ Order # _______________________ The following information is given ...
-
Grizzly H5503 - page 16
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here ...
Do you have a question concerning Grizzly H5503?
Use the form below
If you did not solve your problem by using a manual Grizzly H5503, ask a question using the form below. If a user had a similar problem with Grizzly H5503 it is likely that he will want to share the way to solve it.