Manual Hearth and Home Technologies GDST5244IL

60 pages 5.72 mb
Download

Go to site of 60

Summary
  • Hearth and Home Technologies GDST5244IL - page 1

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 1 Model(s): GDST5244I GDST5244IL Direct V ent Gas Appliance Owner ’ s Manual Installation and Operation Installation and service of this appliance should be performed by quali fi ed personnel. Hearth & Home T echnologies suggests NFI certi fi ed or factory-trained professionals, or ...

  • Hearth and Home Technologies GDST5244IL - page 2

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fi replace: _____________________ Dealership purchased from: _____________________ ...

  • Hearth and Home Technologies GDST5244IL - page 3

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous situation which, if ...

  • Hearth and Home Technologies GDST5244IL - page 4

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 4  = Contains updated information. 14 Appliance Setup A. Remove Fixed Glass Assembly 44 B. Remove the Shipping Materials 44 C. Clean the Appliance 44 D. Accessories 44 E. Install the Log Set 44 F . Place the Rockwool 46 G. Place the Lava Rock and V ermiculite 46 H. Fixed Glass Assembly 4 ...

  • Hearth and Home Technologies GDST5244IL - page 5

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 5 B. W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States ...

  • Hearth and Home Technologies GDST5244IL - page 6

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 6 B. W arranty (continued) This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of th ...

  • Hearth and Home Technologies GDST5244IL - page 7

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 7 B. T empered Glass Speci fi cations Hearth & Home T echnologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as de fi ned by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certi ...

  • Hearth and Home Technologies GDST5244IL - page 8

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 8 H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side w ...

  • Hearth and Home Technologies GDST5244IL - page 9

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 9 Mantel Decorative Doors (not shown) Section 2.E. Fixed Glass Assembly Section 2.F . Grate (not shown) Section 3.B. Hearth (not required) Clear Space Section 2.D. Fan Kits Section 2.C Figure 2.1 General Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before reading and unders ...

  • Hearth and Home Technologies GDST5244IL - page 10

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 10 Clear space 3 ft (914 mm) in front of appliance D. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat m ...

  • Hearth and Home Technologies GDST5244IL - page 11

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 1 1 I. Lighting Instructions (IPI) • For normal use, activate/deactivate your fi replace with the wall switch or remote control. • The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer . T o prolong battery life, remove them when using t ...

  • Hearth and Home Technologies GDST5244IL - page 12

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 12 Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the fi replace of f and allow it to completely cool. • Remove fi xed glass assembly . See Section 14.H. • Clean fi xed glass assembly . See Section 3.A. • Replace the ? ...

  • Hearth and Home Technologies GDST5244IL - page 13

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 13 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care. Glass is breakable. • Avoid striking, scratching or slamming glass • Avoid abrasive cleaners ? ...

  • Hearth and Home Technologies GDST5244IL - page 14

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 14 Control Compartment and Firebox T op Frequency: Annually By: Quali fi ed Service T echnician T ools needed : Protective gloves, vacuum cleaner , dust cloths • V acuum and wipe out dust, cobwebs, debris or pet hair . Use caution when cleaning these areas. Screw tips that have penetrate ...

  • Hearth and Home Technologies GDST5244IL - page 15

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 15 Noncombustible roof flashing maintains minimum clearance around pipe (SECTION 10) Ceiling Firestop on floor of attic (SECTION 8) V ent Pipe (SECTIONS 7, 8, 10) Framing/Header (SECTION 5) Gas Line (SECTION 1 1) Framing Headed off in Ceiling Joists (SECTION 8) Mantel & Mantel Leg (SECT ...

  • Hearth and Home Technologies GDST5244IL - page 16

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 16 B. Design and Installation Considerations Heatilator direct vent gas appliances are designed to op- erate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. Installation MUST comply wi ...

  • Hearth and Home Technologies GDST5244IL - page 17

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 17 5 5 F raming and Clearances A. Select Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). W ARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access. Due ...

  • Hearth and Home Technologies GDST5244IL - page 18

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 18 30 in. (762 mm) to ceiling 0 in. D C B A (top) Drywall 1/2 in. (13 mm) 0 in. TO LEVEL OF ST ANDOFFS Combustible Object 36 in. (914 mm) Combustible flooring may be installed next to the front of the appliance. Figure 5.2 Clearances to Combustibles C. Clearances NOTICE: Install appliance o ...

  • Hearth and Home Technologies GDST5244IL - page 19

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 19 Measured from top of fireplace opening (in inches) 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 4-5/8 6-1/4 7 7-3/4 8-1/2 9-1/4 10 10-3/4 11 - 1 / 2 12-1/4 13 13-3/4 14-1/2 15-1/4 16 16-3/4 30 in. minimum to ceiling D. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all mini ...

  • Hearth and Home Technologies GDST5244IL - page 20

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 20 A. V ent T ermination Minimum Clearances Figure 6.1 Minimum Height From Roof T o Lowest Discharge Opening Horizontal overhang 12 X 20 in. (508 mm) Lowest Discharge Opening T ermination Cap Roof Pitch is X / 12 V ertical wall H (min.) - Minimum height from roof to lowest discharge opening ...

  • Hearth and Home Technologies GDST5244IL - page 21

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 21 Dimension Descriptions A Clearance above the ground, a veranda, porch, deck or balcony - 12 in. (30 cm) minimum. * B Clearance to window or door that may be opened – 10,000 BTUs or less, 6 in. (15 cm) minimum; 10,000-50,000 BTUs, 9 in. (23 cm) minimum; over 50,000 BTUs, 12 in. (30 cm) ...

  • Hearth and Home Technologies GDST5244IL - page 22

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 22 Horizontal V ertical 8-1/2 in. 8-1/2 in. 12 in. On 45° runs, 1 ft (.3 m) of diagonal is equal to 8-1/2 in. (216 mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A. Approved Pipe This appliance is approved for use with Hearth & Home T echnologies DVP and/or SLP venting systems ...

  • Hearth and Home Technologies GDST5244IL - page 23

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 23 H 1 V 1 T o replace the fi rst starter elbow with two 45° elbows, refer to Figure 7.4. All other 90° elbows can be replaced with two 45° elbows. General Rules: • SUBTRACT 3 ft. from the total H measurement for each 90° elbow installed horizontally . • SUBTRACT 1-1/2 ft. from the ...

  • Hearth and Home Technologies GDST5244IL - page 24

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 24 4 ft min. (1.22 m) 25 ft max. (7.62 m) H 1 V 1 H 2 H 3 Installed Horizontally Installed V ertically H 2 Figure 7.5 T wo Elbows 1. T op V ent - Horizontal T ermination - (continued) Figure 7.4 T wo 45° Elbows replacing One 90° Elbow V 1 min. V 1 max. H 1 +H 2 max. H 1 +H 2 +H 3 max. ft ...

  • Hearth and Home Technologies GDST5244IL - page 25

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 25 Figure 7.6 1. T op V ent - Horizontal T ermination - (continued) Three Elbows H 1 V 1 V 2 H 2 Installed V ertically V 1 min. V 1 + V 2 max. H 1 +H 2 max. ft m ft m ft m 1 0.30 24 7.32 19 5.79 ...

  • Hearth and Home Technologies GDST5244IL - page 26

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 26 2. T op V ent - V ertical T ermination No Elbow Figure 7.7 Figure 7.8 T wo Elbows Note: If installing a verti- cal vent/termination off the top of the appliance, the fl ue restrictor should be used. 12 ft (3.66 mm) min. 60 ft (18.29 m) max. 12 ft (3.66 m) min. 60 ft (18.29 m) max. Maxim ...

  • Hearth and Home Technologies GDST5244IL - page 27

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 27 Figure 7.9 2. T op V ent - V ertical T ermination - (continued) Three Elbows 12 ft (3.66 m) min. 60 ft (18.29 m) max. Maximum horizontal run is 100% of vertical, but cannot exceed 26 ft (7.92 m) ...

  • Hearth and Home Technologies GDST5244IL - page 28

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 28 * When using SLP pipe, minimum clearances from the vent pipe to combustible materi- als at inside wall firestops are: T op: 2-1/2 in. (64 mm) Bottom: 1/2 in. (13 mm) Sides: 1 in. (25 mm) Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). • DVP heat shield - designed to ...

  • Hearth and Home Technologies GDST5244IL - page 29

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 29 3 fasteners per side Ceiling firestop installed below ceiling. Ceiling firestop installed above ceiling. Install attic insula- tion shields before or after installation of vent system. A TTIC ABOVE A PIPE DVP SLP A 10 in. (254 mm) 9 in. (229 mm) A C. Install the Ceiling Firestop A ceilin ...

  • Hearth and Home Technologies GDST5244IL - page 30

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 30 Bend all tabs inward 90° to maintain clearance and prevent insulation from falling inside Insert 3 screws Bend 4 tabs inward 90° to maintain clearance D. Install Attic Insulation Shield W ARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home T e ...

  • Hearth and Home Technologies GDST5244IL - page 31

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 31 Nailing T abs (on front and back sides) A. Secure and Level the Appliance W ARNING! Risk of Fire! Prevent contact with: • Sagging or loose insulation • Insulation backing or plastic • Framing and other combustible materials Block openings into the chase to prevent entry of blown-in ...

  • Hearth and Home Technologies GDST5244IL - page 32

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 32 Lances 1 0 10 Install V ent Pipe A. Assemble V ent Sections (DVP Only) Attach Pipe to the Firebox Assembly Note: The end of the pipe sec tions with the lanc ed tabs will face towards the applianc e. Attach the fi rst pipe section to the starting collar: • Lanced pipe end to the starti ...

  • Hearth and Home Technologies GDST5244IL - page 33

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 33 B. Assemble V ent Sections (SLP Only) T o attach the fi rst vent component to the starting collars of the appliance • Attach an SLP-DVP24 adapter to the starting collar of the appliance. • Lock the vent components into place by sliding the pipe section onto the collar . • Align th ...

  • Hearth and Home Technologies GDST5244IL - page 34

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 34 Figure 10.8 Securing V ertical Pipe Sections Figure 10.9 Securing Horizontal Pipe Sections E. Disassemble V ent Sections • Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown in Figure 10.1 1. • Pull carefully to separate the pieces of pip ...

  • Hearth and Home Technologies GDST5244IL - page 35

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 35 Cut hole 1/8 in. (3 mm) greater in size than pattern of support box as it is projected onto roofline. 2 in. (51 mm) minimum below finished ceiling Cathedral ceiling support box Level F . Install Decorative Ceiling Components (SLP only) A decorative ceiling thimble can be installed on a ? ...

  • Hearth and Home Technologies GDST5244IL - page 36

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 36 Horizontal overhang 12 X 20 in. (508 mm) Lowest Discharge Opening T ermination Cap Roof Pitch is X / 12 Ve r t i c a l wall H (min.) - Minimum height from roof to lowest discharge opening. 24 in. min. (610 mm) Roof Pitch H (Min.) Ft. Roof Pitch H (Min.) Ft. Flat to 6/12 1.0* Over 1 1/12 ...

  • Hearth and Home Technologies GDST5244IL - page 37

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 37 I. Install RF4-8 The RF4-8 may be used in place of the roof fl ashing and storm collar . Pipe must be supported within 12 in. (305 mm) of the roo fl ine using plumbers strapping or an SLP-FS when using the RF4-8 Flashing. Refer to Sect. 10.D. Securing V ent Sections. SLP-FS Secure with ...

  • Hearth and Home Technologies GDST5244IL - page 38

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 38 K. Install Decorative W all Components (SLP only) A decorative wall thimble can be installed on an interior wall through which the vent passes. The decorative wall thimble is used to cover the wall shield fi restop. • Slide the decorative wall thimble over the last section of horizont ...

  • Hearth and Home Technologies GDST5244IL - page 39

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 39 INTERIOR Heat Shield or Extended Heat Shield W all Shield Firestop Heat Shield 1-1/2 in. (38 mm) min. overlap SHEA THING V ent depth from back of appliance to outside surface of exterior wall (see chart below) Slip Section can be extended Inner V ent Outer V ent EXTERIOR Figure 10.26 V e ...

  • Hearth and Home Technologies GDST5244IL - page 40

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 40 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home T echnologies speci fi ed and approved parts. B. Gas Pressure • Optimum appliance performance requires proper i ...

  • Hearth and Home Technologies GDST5244IL - page 41

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 41 A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric Code CSA C22.1. • Wire the appliance junction box t ...

  • Hearth and Home Technologies GDST5244IL - page 42

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 42 E. Junction Box Installation If the box is being wired from the OUTSIDE of the appli- ance: • Remove the cover plate located on the outer shell - right side (see Figure 12.2). • Install the supplied Romex™ connector in the cover plate. • Feed the necessary length of wire through ...

  • Hearth and Home Technologies GDST5244IL - page 43

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 43 0 in. min. to perpendicular wall A 4-5/8 in. (1 17 mm) min. from fireplace opening to perpendicular wall B Mantel Leg or Perpendicular W all T op of Appliance Drywall A B Measured from top of fireplace opening (in inches) 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 4-5/8 6-1/4 7 7-3/4 8-1/2 ...

  • Hearth and Home Technologies GDST5244IL - page 44

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 44 A. Remove Fixed Glass Assembly See Section 14.H. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity . D. Acc ...

  • Hearth and Home Technologies GDST5244IL - page 45

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 45 Notch Figure 14.4 Place T op - Left Log (#7) Placed on Pin P3 and Lays Across Notch in Middle Base Log Notch Figure 14.5 Place T op - Middle, Back Log (#8) Placed on Pin P4 and Lays on Notch of Log 6 Figure 14.6 Place T op - Right, Back Log (#9) Placed on Pins P5 & P6 Sets here Figur ...

  • Hearth and Home Technologies GDST5244IL - page 46

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 46 Latches (both bottom and top) Glass Assembly K. Air Shutter Setting Air shutter settings should be adjusted by a quali fi ed installer at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shut- ter for longer vertical runs. See Fig ...

  • Hearth and Home Technologies GDST5244IL - page 47

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 47 1 5 15 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service technician in the diagnosis of a problem and the corre ...

  • Hearth and Home Technologies GDST5244IL - page 48

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 48 Intelli fi re Ignition System - (continued) Symptom Possible Cause Corrective Action 4. Pilot lights but continues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot fl ame has been lit, fl ame recti fi cation has not occurred.) A. A shorted o ...

  • Hearth and Home Technologies GDST5244IL - page 49

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 49 1 6 16 Reference Materials 42-1/8 in. (1070 mm) 37-3/8 in. (949 mm) 44-3/8 in. (1 127 mm) 44 in. (1 1 18 mm) 12 in. (305 mm) 52-1/8 in. (1324 mm) 24 in. (610 mm) 4-1/8 in. (105 mm) 2-7/8 in. (73 mm) 5-1/8 in. (130 mm) 3-1/8 in. (80 mm) 6-7/8 in. (175 mm) 5 in. (127 mm) Gas Knockouts 5 in ...

  • Hearth and Home Technologies GDST5244IL - page 50

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 50 B. V ent Components Diagrams Figure 16.2 DVP V ent Components Effective Height/Length DVP Pipe (see chart) Pi p e inches mm DVP4 4 102 DVP6 6 152 DVP12 12 3 05 DVP24 24 6 10 DVP36 36 9 14 DVP48 48 1219 DVP6A 3 - 6 76 - 152 DVP12A 3 - 12 76 - 305 Effective Height/Length 10-1/2 in. (267 mm ...

  • Hearth and Home Technologies GDST5244IL - page 51

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 51 B. V ent Components Diagrams ( continued ) Figure 16.3 DVP V ent Components 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (698 mm) RF6M Roof Flashing Multi-pak 31 in. (787 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF12M Roof Flashing Multi-pak BEK T rap Cap Brick Extension 13-3/4 ...

  • Hearth and Home Technologies GDST5244IL - page 52

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 52 B. V ent Components Diagrams ( continued ) Figure 16.4 DVP V ent Components DVP-TB1 Basement V ent Cap 12 in. (305 mm) 1-1/2 in. (38 mm) 7-3/8 in. (187 mm) 14 in. (356 mm) 17-3/4 in. (451 mm) 10-1/2 in. (267 mm) 3-7/8 in. (98 mm) DVP-TV V ertical T ermination Cap PVK-80 (For use with IPI ...

  • Hearth and Home Technologies GDST5244IL - page 53

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 53 B. V ent Components Diagrams ( continued ) Figure 16.5 DVP V ent Components DVP-TRAP1 DVP-TRAP2 DVP-HPC1 DVP-HPC2 DVP-TRAPK1 DVP-TRAPK2 DVP-TRAP Horizontal T ermination Cap 15-1/8 in. (384 mm) 12 in. (305 mm) 8 in. (203 mm) Max Effective Length Note: Heat shields MUST overlap by a minimu ...

  • Hearth and Home Technologies GDST5244IL - page 54

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 54 B. V ent Components Diagrams (continued) Figure 16.6 DVP V ent Components 13 in. (330 mm) 15 in. (381 mm) 8-1/8 in. (206 mm) DVP-HRC-SS 10-7/8 in. 276 mm 10-1/2 in. 267 mm 3° 87° Effective Length 5-3/4 to 8-3/8 in. 146 to 213 mm 5-1/2 in. 140 mm 8-3/8 in. 213 mm DVP-HRC-ZC-SS Fillers D ...

  • Hearth and Home Technologies GDST5244IL - page 55

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 55 B. V ent Components Diagrams (continued) Figure 16.7 SLP Series V ent Components 8-3/4 in. 222 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 6 in. 152 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 9-7/8 in. 251 mm 6-1/2 in. 165 mm 9-1/4 in. 235 mm SLP-45 - 45° Elbow SLP-90ST - 90° Elbow Effective Height ...

  • Hearth and Home Technologies GDST5244IL - page 56

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 56 B. V ent Components Diagrams (continued) Figure 16.8 SLP Series V ent Components SL-2DVP Adapter SLK-SNKD Snorkel T ermination Cap SLP-TVHW V ertical T ermination Cap PVK-80 Power V ent DVP-FBHT Firebrick T ermination Cap (This termination cap requires an SL-2DVP adapter when used with S ...

  • Hearth and Home Technologies GDST5244IL - page 57

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 57 C. Service Parts Service Parts 09/08 Service Parts Diagram 44 in. See-Through Gas Fireplace - DV GDST5244I Part number list on following page. Log Set Assembly 12 13 19 20 15 17 24 18 22 16 25 26 21 23 14 Bottom Logs (shipped in place) 1 2 3 4 5 T op Logs 7 6 8 9 1 10 1 Beginning Manufac ...

  • Hearth and Home Technologies GDST5244IL - page 58

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 58 Service Parts 09/08 IPI V alve Assembly 8 6 4 9 12 11 2 10 13 7 1 5 3 V alve Assembly Parts List 44 in. See-Through Gas Fireplace - DV Beginning Manufacturing Date: Jan. 2005 Ending Manufacturing Date: Active GDST5244I IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or ...

  • Hearth and Home Technologies GDST5244IL - page 59

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 59 D. Optional Components Optional Accessories (shipped separately) FFSTM44 Modernist-style black decorative faux front (one side only) FFSTM44PT Modernist-style pewter decorative faux front (one side only) FFST AC44 Arts & Crafts-style black decorative faux front (one side only) FFST A ...

  • Hearth and Home Technologies GDST5244IL - page 60

    Heatilator • GDST5244I • 4045-127 • Rev W • 1 1/08 60 E. Contact Information Please contact your Heatilator dealer with any questions or concerns. For the location of your nearest Heatilator dealer , please visit www .heatilator .com. - NOTES - ________________________________________________________________________________ ________________ ...

Manufacturer Hearth and Home Technologies Category Indoor Fireplace

Documents that we receive from a manufacturer of a Hearth and Home Technologies GDST5244IL can be divided into several groups. They are, among others:
- Hearth and Home Technologies technical drawings
- GDST5244IL manuals
- Hearth and Home Technologies product data sheets
- information booklets
- or energy labels Hearth and Home Technologies GDST5244IL
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hearth and Home Technologies GDST5244IL.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hearth and Home Technologies GDST5244IL, service manual, brief instructions and user manuals Hearth and Home Technologies GDST5244IL. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hearth and Home Technologies GDST5244IL.

A complete manual for the device Hearth and Home Technologies GDST5244IL, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hearth and Home Technologies GDST5244IL by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hearth and Home Technologies GDST5244IL.

A complete Hearth and Home Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hearth and Home Technologies GDST5244IL - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hearth and Home Technologies GDST5244IL, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hearth and Home Technologies GDST5244IL, that we can find in the current document
3. Tips how to use the basic functions of the device Hearth and Home Technologies GDST5244IL - which should help us in our first steps of using Hearth and Home Technologies GDST5244IL
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hearth and Home Technologies GDST5244IL
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hearth and Home Technologies GDST5244IL in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hearth and Home Technologies GDST5244IL?

Use the form below

If you did not solve your problem by using a manual Hearth and Home Technologies GDST5244IL, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies GDST5244IL it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)