English dropdown-ico

Manual Porter-Cable 7310

25 pages 0.38 mb
Download

Go to site of 25

Summary
  • Porter-Cable 7310 - page 1

    Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...

  • Porter-Cable 7310 - page 2

    T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property ...

  • Porter-Cable 7310 - page 3

    Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry produ ...

  • Porter-Cable 7310 - page 4

    4 Read all instructions Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. GENERAL SAFETY RULES* SAVE THESE INSTRUCTIONS 1) Work area ...

  • Porter-Cable 7310 - page 5

    5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose ...

  • Porter-Cable 7310 - page 6

    6 ADDITIONAL SPECIFIC SAFETY RULES 1. HOLD POWER TOOLS BY INSULATED GRIPPING SURFACES WHEN PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2 . USE CLAMPS OR OTHER PRACTICAL WAY TO SECURE A ...

  • Porter-Cable 7310 - page 7

    7 NOTES ...

  • Porter-Cable 7310 - page 8

    8 SAVE THESE INSTRUCTIONS! SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g .................... ...

  • Porter-Cable 7310 - page 9

    9 If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amp ...

  • Porter-Cable 7310 - page 10

    10 FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable Laminate Trimmers are designed for flush and bevel trimming laminated plastics, phenolics, and other similar materials having a bonding agent too hard to be trimmed with ordinary tools. The Tilt-Base model allows trimming into corners inaccessible to standard trimmers and to trim laminated surfaces jo ...

  • Porter-Cable 7310 - page 11

    11 to stop motor. To avoid personal injury or damage to finished work always allow the motor to come to a COMPLETE STOP before setting trimmer down. TO INST ALL BIT DISCONNECT TOOL FROM POWER SOURCE. 1. On Models 7310 and 7319 bits may be installed with the motor unit either assembled or removed from the base. See instructions under Model 7312 for ...

  • Porter-Cable 7310 - page 12

    ADJUSTING DEPTH OF CUT DISCONNECT TOOL FROM POWER SOURCE. 1. Loosen base locking screw (Fig. 3) approximately one-quarter turn. 2. Turn depth adjusting wheel (Fig. 3) clockwise, looking at top of wheel, to raise cutter reducing depth of cut or counterclockwise to lower cutter for increasing depth of cut. 3. Tighten base locking screw securely and m ...

  • Porter-Cable 7310 - page 13

    13 ASSEMBLING AND ADJUSTING BASE AND GUIDE 1 . The base and roller guide (A) Fig. 4, are assembled at the factory. To assemble to trimmer: Remove one sub-base mounting screw (A) Fig. 5, insert alignment pin in guide base into hole in bottom of trimmer sub-base and fasten with two mounting screws (F) Fig. 4, as shown in Fig. 5A. Do not tighten at th ...

  • Porter-Cable 7310 - page 14

    14 4. Adjust guide until hole in gauge fits over stud on end of gauge. Tighten all screws securely. 5. Remove guide setting gauge from trimmer and install the bit as outlined under TO INSTALL BIT. NOTE: It will be necessary to separate motor from base to remove setting gauge and install bit. 6. Adjust depth of cut so that the straight portion of bi ...

  • Porter-Cable 7310 - page 15

    15 Loosen base locking screw and move motor unit up or down to decrease or increase depth of cut. It may be necessary with some bits to withdraw bit from collet to obtain maximum depth of cut. When doing this be sure at least 1 / 2 " of bit shank is engaged in collet. Do not use bits that result in having less than 1 / 2 " of bit shank en ...

  • Porter-Cable 7310 - page 16

    16 7. Clean collet nut and collet, and assemble to the spindle in the offset base. DO NOT TIGHTEN COLLET NUT AT THIS TIME. Tightening the collet nut without a bit installed in the collet is likely to damage the collet. 8. Position sub-base to base housing and secure with the three screws that were removed in step 3. TO INST ALL & REMOVE BIT DIS ...

  • Porter-Cable 7310 - page 17

    17 OPERA TION 1. Material to be trimmed must overhang the base material by at least 1 / 8 ". 2. Always wear safety glasses while operating a laminate trimmer. 3. DISCONNECT TOOL FROM POWER SOURCE. 4. Firmly grasp motor housing being sure switch is in the “OFF” position. 5. Verify bit is clear of foreign objects and cord will not “hang up ...

  • Porter-Cable 7310 - page 18

    18 UNDERSCRIBE 7320 TRIMMER ASSEMBL Y The Underscribe Trimmer Base is assembled to the Model 7301 Trimmer Motor as follows: NOTE: The 43109 Trim Bit must be installed into the Trimmer Motor before attaching the motor to the Underscribe Base. DISCONNECT TOOL FROM POWER SOURCE. 1. Clean and insert shank of bit (A) Fig. 14, into collet until end of sh ...

  • Porter-Cable 7310 - page 19

    19 hand until lock engages hole in motor spindle. 3 . While holding spindle lock engaged, tighten collet nut securely by turning clockwise using wrench provided. NEVER TIGHTEN COLLET WITHOUT BIT INSERTED, TO DO SO MAY CAUSE DAMAGE TO COLLET. 4. Position base (A) Fig. 15, to motor (B) and secure using locking screw (E), spring (D) and washer (C). NO ...

  • Porter-Cable 7310 - page 20

    20 4. Repeat Steps 1 through 3 as required to achieve a good fit- up. USING THE UNDERSCRIBE TRIMMER The bottom plate of the Underscribe Trimmer has a guide lip (see Fig. 17). This guide lip is moved along an installed piece of laminate as the trimmer bit cuts the mating piece of laminate. The “butt” joint is commonly used in the construction of ...

  • Porter-Cable 7310 - page 21

    21 5. Position the underscribe trimmer onto the face frame so that the top (see Fig. 19), is against the edge of the stile. NOTE: The trimmer should be to the right of the rail, so that the cutting action will move from right to left (see Fig. 19). 6. Verify that bit is clear of foreign objects and that cord will not hang on any obstructions. 7. Gr ...

  • Porter-Cable 7310 - page 22

    22 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. F AILURE TO ST ART Should your tool fail t ...

  • Porter-Cable 7310 - page 23

    23 SERVICE REPLACEMENT P ARTS When servicing use only identical replacement parts. SERVICE AND REP AIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations, including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED PORTER- CABLE SERVICE STATION ...

  • Porter-Cable 7310 - page 24

    24 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...

  • Porter-Cable 7310 - page 25

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

Manufacturer Porter-Cable Category Trimmer

Documents that we receive from a manufacturer of a Porter-Cable 7310 can be divided into several groups. They are, among others:
- Porter-Cable technical drawings
- 7310 manuals
- Porter-Cable product data sheets
- information booklets
- or energy labels Porter-Cable 7310
All of them are important, but the most important information from the point of view of use of the device are in the user manual Porter-Cable 7310.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Porter-Cable 7310, service manual, brief instructions and user manuals Porter-Cable 7310. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Porter-Cable 7310.

Similar manuals

A complete manual for the device Porter-Cable 7310, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Porter-Cable 7310 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Porter-Cable 7310.

A complete Porter-Cable manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Porter-Cable 7310 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Porter-Cable 7310, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Porter-Cable 7310, that we can find in the current document
3. Tips how to use the basic functions of the device Porter-Cable 7310 - which should help us in our first steps of using Porter-Cable 7310
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Porter-Cable 7310
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Porter-Cable 7310 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Porter-Cable 7310?

Use the form below

If you did not solve your problem by using a manual Porter-Cable 7310, ask a question using the form below. If a user had a similar problem with Porter-Cable 7310 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)