-
AEG Protect A. 700 VA - page 1
UPS OPER ATING INSTRUCTIO NS PROTECT A . 1000 PROTECT A . 1400 PROTECT A. ...
-
AEG Protect A. 700 VA - page 2
2 ...
-
AEG Protect A. 700 VA - page 3
3 EN Thank you fo r deciding t o purchase the PROT ECT A. UPS from AE G Pow er Solutions. The following safety instructions are an important part of the operating instruction s are will protect y ou against problems from operating errors and possible dangers. Please read these instructions carefully prior to commissioning! ...
-
AEG Protect A. 700 VA - page 4
4 1 Notes on these Operating Instructions Duty to provide information These operating instructions will help you to install an d operate the U ninterruptible Po wer Supply (UPS), PROTECT A . 1000 or PROT ECT A. 14 00 - referred to as PROTECT A . in this document - safely and properl y, and f or its i ntended purpose. T hese op erating instructions ...
-
AEG Protect A. 700 VA - page 5
5 EN obligations suc h as warra nty agreements, service contracts , etc. entered into by A EG or its representatives without prior notice in the event of maintenanc e and r epair w ork being carried out wit h a nything other than original AEG parts or spare parts purchas ed from AEG. Handling PROTECT A . is desi gned and co nstructed so that all ne ...
-
AEG Protect A. 700 VA - page 6
6 Table of Contents 1 Notes on these Opera ting Instruc tions ..............................4 2 System Overvie w .................................... ..........................7 2.1 Brief Overvie w .......................................... ..................7 2.2 Principle of Operat ion............................... ..................8 3 Safety . ...
-
AEG Protect A. 700 VA - page 7
7 EN 6 Displays and Tr oubleshooting .........................................26 6.1 LC Displa y ............................................... .................26 6.2 W arning Sounds........................................ ...............29 6.3 General Tr oubleshooting and Fault R ectification .....29 7 Maintenance ............................... ...
-
AEG Protect A. 700 VA - page 8
8 Important UPS data is m onitored perm anently an d transf erred to the com puter via U SB or the RS232 in terface and u sing the CompuW atch software. Features of the PROT ECT A.: ♦ VI (line – interactive) protec tion technolog y ♦ Autom atic voltage regulatio n against mains voltage deviations (AVR) ♦ Microproces sor control for hig h re ...
-
AEG Protect A. 700 VA - page 9
9 EN Inverter Battery Rectifier Load Mains Line filter A. V. R. ~ ~ the i nternal energ y st orage, som ething which in tur n has a positive eff ect on battery availab ility. UPS Block diagra m PROTECT A . The static by pass switch is a ctivated in the event of a m ains failure. The inverter t hen tak es over t he voltage sup ply of t he connected ...
-
AEG Protect A. 700 VA - page 10
10 3 Safety 3.1 General Safety Instructions Read these oper ating instructions carefully prior to commiss ioning of the PR OTECT A. UPS and observe the safety instructions! Only us e the unit if it is in a technically perf ect c ondition and always in accordance with its intended purpose , while being aware of safety a nd danger aspects, and in acc ...
-
AEG Protect A. 700 VA - page 11
11 EN The output ma y be live, e ven if th e U PS is not connected to the m ains supp ly, as the U PS has its own internal po wer suppl y (battery)! For health and safet y reasons, the uni t m ust be earthed correctl y! PROTECT A. m ay onl y be operated with or connected to a 220 / 230 / 240 VA C m ains with protect ive grou nding us ing a mains co ...
-
AEG Protect A. 700 VA - page 12
12 ♦ Condensat ion may occur if the UPS is brough t from a cold environm ent into the room where it is to be installed. The U PS must be absol utely dry prior to start - up. As a result, leave it to acc limatise for at least two hours. ♦ Never c onnect the m ains input and the UP S output! ♦ Ensure that no fluids or foreig n bodies can pene t ...
-
AEG Protect A. 700 VA - page 13
13 EN W hen replacing t he batt eries, the fol lowing m ust be o bserved: Only ever use identical , maintenance-free sea led lead batteries with the sam e data as the ori ginal batteries . Danger! Explosive ! Never throw batteries into open fire. Never open or dam age batteries. (Elec trolyte m ay leak out and damage sk in and eyes. It m ay be toxi ...
-
AEG Protect A. 700 VA - page 14
14 3.3 CE Certificate ...
-
AEG Protect A. 700 VA - page 15
15 EN 3.4 Technical Data Type rating PROTECT A. 1000 1000 VA / 600 W PROTECT A. 1400 1400 VA / 840 W UPS input Nominal connecti on voltage 220 / 230 / 240 Vac Voltage range with out batter y 170 Vac to 280 Vac Frequenc y (automatic detection) 50 / 60 Hz Connection Non-heating app liance connector IEC 320 C 14 UPS output Rated output volta ge / 230 ...
-
AEG Protect A. 700 VA - page 16
16 Charging tim e (to 90 % of rated ca pacity) 6 h T y pe Sealed, m aintenance-free PROTECT A. 1000 2 bl ock b at te ri e s 1 2 V / 7 A h e.g. C SB, type GP1272F2 3- 5 y ear s a cc. t o EU R OBA T Yuasa, type NP7- 12D Connection plug 6.3 mm Panasonic, t ype LC-R127R2P (Fas ton 250) PROTECT A. 1400 2 block bat teri es 1 2 V / 9 A h e.g. C SB, type H ...
-
AEG Protect A. 700 VA - page 17
17 EN Directives The PROT ECT A. meets the prod uct standard EN 5 0091. The CE m ark on the unit confirm s compliance with the EC outline directives f or 73/23 EEC – L ow voltage and f or 89/336 EEC – Electrom agnetic com patibility if the instal lation instructions describ ed in the oper ating instructions are observed. For 73/23 EEC lo w-volt ...
-
AEG Protect A. 700 VA - page 18
18 Check the content is complete: ♦ PROT ECT A. with 1000 or 1400 VA ♦ Mains c onnection cable with shockpr oof plug acc. to CEE 7/7 Second m ains connection cable with UK plug acc. to BS 1363 ♦ T wo device connecting cab les ♦ USB / R S232 comm unication cable ♦ Managem ent software “Co mpuW atch” on CD ♦ Operating instructions Ple ...
-
AEG Protect A. 700 VA - page 19
19 EN 4.3 Connections, Operating and Display Elements Front Rear 1 Main switch of the U PS (mains switch) 2 LC display with: - Display of operat ing mode with pictogram s - Measured value d isplays [V] - UPS capacit y utilisation dis play [%] - UPS rem aining op. time displa y [min.] - Fault indication 1 Load connections with overvoltage protecti o ...
-
AEG Protect A. 700 VA - page 20
20 5 Inst allation and Operatio n 5.1 Check Remove the UPS f rom its transport packaging and check that it has not been dam aged in tra nsit. If you find an y dam age, pack the unit up again and send it back to w here you purchased it. 5.2 Installation Install t he U PS unit in a pr otected location where th ere i s an adequate air s upply a nd whe ...
-
AEG Protect A. 700 VA - page 21
21 EN 5.3 Charging The PROT ECT A. is supplied with its batter y f ully c harged. Nevertheless, energ y m ay have been lost d uring transport, so the batter y should be fully recharged before it is used f or the first time. Connect the input of the U PS (no. 2 in the f igure in c hapter 4. 3 on page 19) to the mains connection cable pr ovided a nd ...
-
AEG Protect A. 700 VA - page 22
22 i In this c onnection, note the special pr operty of the two additional output s ockets identified with “SURGE ONL Y” (chapter 4.3 / no. 7 / pg . 19). These are always live irr espective of the other outputs. T hey are n ot bac ked up by the UPS, nor can the y be s witched off using the m ain s witch of the UP S. It is intended for loads tha ...
-
AEG Protect A. 700 VA - page 23
23 EN i The interfaces are mutuall y exc lusive. T here is no provision f or simultaneous operation of RS232 and USB. 5.7 Operation Once you have con nected the UPS to a suitable mains connection, you can start operat ion using the UPS main switch. Switching O N and OFF: To switch on, pres s the main switch on the f ront of the UPS (chapter 4.3 ...
-
AEG Protect A. 700 VA - page 24
24 The connected l oads are po wered using the m onitored and filtered m ains voltage , whi ch is ad ditionally st abilised by th e integrated A.V.R. control unit. The “LINE MODE” symbol shows that the un it is active. 5.7.2 Battery Operation / Auton omous Operation W hen there is a m ains fai lure or if the input voltage m oves outside the t o ...
-
AEG Protect A. 700 VA - page 25
25 EN 5.7.3 System Diagnosis / Fault Test If the m onitoring e lectronics dete ct an irregularity, the fault indicator is ac tivated which is sig nalled b y th e “Fault” pictogram and a digita l f ault c ode, possibl y acc ompanied b y an acous tic fault signa l. This might occur beca use th e batter y undervoltage lim it has been reached, if t ...
-
AEG Protect A. 700 VA - page 26
26 6 Displays and T roublesh ooting 6.1 LC Display The blue back lit displa y is automatically act ivated after the mains voltage is con nected. It oper ates irrespectiv e of the main switch setting and also when a fault is indicated. 1) The start of operational re adiness is signalled on the LC display by all t he inform ation content lighti ng up ...
-
AEG Protect A. 700 VA - page 27
27 EN 4) If the UPS is in battery mode, th e “BATTER Y” pictogram lights up and the ba ttery sym bol flashes ever y second. The remaining s tandb y tim e is displayed dur ing b attery operation accor ding to the load a pplied. T his time is shown in minutes and is in dicated by the “MIN” pictogram . i The display sho ws “0” if the volta ...
-
AEG Protect A. 700 VA - page 28
28 Fault CODE Possible fault cause 01 Output short circuit (output voltage less th an 60 V) 02 Overload indicator Immediate fau lt mess age in m ains/normal operation with a cap acity utilisation of > 120%, at a c apacit y utilisation > 110% the fault m essage com es after 5 minutes or after 30 seconds in battery operation. 03 Output voltag e ...
-
AEG Protect A. 700 VA - page 29
29 EN 6.2 Warning Sounds Warning sound Meaning Sounds every 10 seconds. UPS is operating in battery mode. Sounds every second. UPS is running in ba ttery mode an d will shortly shut down (battery system has rea ched the battery undervo ltage limit). Sounds every tw o seconds Battery syste m faulty, it may have to be re newed (battery diagnosi s neg ...
-
AEG Protect A. 700 VA - page 30
30 Miniature circuit breaker triggered Press reset button o f miniature circuit breaker; Mains nor mal, but “Battery” LED fla shes Mains cable loose Insert the plug fir mly into the non- heating appliance so cket of the UPS. Software is not ins talled correctly Check the softw are settings. Support is available at www .AEGpartnerNet.de Communic ...
-
AEG Protect A. 700 VA - page 31
31 EN 7 Maintenance The P ROT ECT A. consists of state-of-the-art, non-wearing components. W e do, however, recomm end regular visual checks of the unit to m aintain its c ontinuous av ailabilit y and operational reliab ility. Check whether: ♦ there is an y mechanical da mage or foreign bodi es can be found in the s ystem, ♦ any cond uctive dir ...
-
AEG Protect A. 700 VA - page 32
32 7.1 Battery Replacement ATTENTIO N: A batter y can cause an electr ic shock, and represents a consid erable hazard if ha ndled incorrectl y. The f ollowing precaution s should b e taken before the batter y is renewed. ♦ Switch of f the UPS and dis connect the m ains cable from the sock et. ♦ Rem ove any rings, wristwat ch and other m etallic ...
-
AEG Protect A. 700 VA - page 33
33 EN Once you hav e l ifted off the ac tual front pane l ( which you c an put down on t op of the u nit as s hown – never d isconnect th e flat-ribbon cable) n ext rem ov e the int ernal battery cove r. Now slowly p ull the two batter y block s out f orwards until yo u can acces s the c able plug c onnections. Firs t disconnect the negative term ...
-
AEG Protect A. 700 VA - page 34
34 8 Sto rage and Disposal Storage Long storag e tim es without charging or discharging the ba tter y at regular interva ls ma y lead to perm anent damage of the batter y. If the batter y is store d at ro om temperature (20° C to 30° C) it will autom atically disc harge at a rate of 3-6% per m onth due to internal reactions. Storing the batter y ...
-
AEG Protect A. 700 VA - page 35
35 EN 9 List of T erms 9.1 Technical Terminology AVR Automatic Voltage Reg ulation Automatic voltage regulation against mains voltage deviations DC/DC booster Circuit technology for increasing a D C voltage to a higher voltage level EPO E mergency Pow er Off Device for emerg ency shutdown PFC P ower Factor Correction Circuit technology for minimisi ...
-
AEG Protect A. 700 VA - page 36
36 Guarantee Certificate T y pe: …….……… ……….…....... ................................ ............... Unit number:…….…… ………….…....... ................................. ............ Date of purchase:…….… …………….….... .......................... ................... Dealer stam p / signature Errors a ...
Do you have a question concerning AEG Protect A. 700 VA?
Use the form below
If you did not solve your problem by using a manual AEG Protect A. 700 VA, ask a question using the form below. If a user had a similar problem with AEG Protect A. 700 VA it is likely that he will want to share the way to solve it.