English dropdown-ico

Manual Canon WUX5000

74 pages Not applicable
Download

Go to site of 74

Summary
  • Canon WUX5000 - page 1

    © 201 1 CANON INC. YT1-1435-001 MUL TIMEDIA PROJECT OR WUX5000 / WUX4000 User Commands Revision 1 ...

  • Canon WUX5000 - page 2

    WUX5000 / WUX4000 User Commands - - ii T able of Contents 1. Overview ................................................................................................................. 1 2. Communication S pecifications ................................................................................. 2 Communication Sp ecifications ................. ...

  • Canon WUX5000 - page 3

    WUX5000 / WUX4000 User Commands - - iii FREEZE ........................................................................................................................ ............ 36 GAMMA ......................................................................................................................... ........... 37 HDMI_IN ............... ...

  • Canon WUX5000 - page 4

    WUX5000 / WUX4000 User Commands - 1 - 1. Overview These specifications describe the method s of controlling both the Projector WUX 5 000 and WUX4000 from the PC over an RS-232C connection or LAN. V irtually all operations possible with the re mote control can be controlled from the P C. The following symbols are used in these specifications: Symbol ...

  • Canon WUX5000 - page 5

    WUX5000 / WUX4000 User Commands - 2 - 2. Communication S pecifications Communication S pecifications The projector can be cont rolled via RS-232C or LAN connection. PC - Projector connec tion configuration Item S pecifications Item S pecifications Connecti on system PC and projector connected on a "1:1" basis Connecti on system TCP / IP C ...

  • Canon WUX5000 - page 6

    WUX5000 / WUX4000 User Commands - 3 - Usable Character Codes Use ASCII codes in the red and blue areas. No distinction is made between double-byte char acters and single-byte charac ters. Do not use double-byte or triple-byte charac ters. They will all be recogniz ed as single-byte characters. Uppercase and lowercase versions of the same alphab eti ...

  • Canon WUX5000 - page 7

    WUX5000 / WUX4000 User Commands - 4 - Communication System (Serial) Item S pecifications Communication system RS-232-C Start-stop synchronization Semi- duplex communication Transmission speed 19.2 Kbps Character length 8 bits / character Stop bit 2 bits Parity No ne Transmission format Variable-length re cords with terminals as delimiters Maximum t ...

  • Canon WUX5000 - page 8

    WUX5000 / WUX4000 User Commands - 5 - Commands T ransmissions sent from the PC to the projector . T ransmission format △ <Command character strings> △ <Delimiter> <Command character st rings> Character string s consisting of 0 or more alphanumeric characters. <Delimiters> One of CR (0Dh), LF (0Ah), CR+LF (0Dh+0Ah), Null ...

  • Canon WUX5000 - page 9

    WUX5000 / WUX4000 User Commands - 6 - Response T ransmissions sent from the Projector to th e PC in response to commands from the PC. T ransmission format <Response character string> <Delimiter> <Response character string > Character strings co nsisting of one or more ASCII characters. The first two characters are always one lower ...

  • Canon WUX5000 - page 10

    WUX5000 / WUX4000 User Commands - 7 - Other T ransmission recognition On the receiving side (the Projector), the data that is able to be received within the character interval of T c is held, and the transmission is consid ered received when the delimiter is received. If the character inter val received exceeds the T c or if a delimiter is n ot rec ...

  • Canon WUX5000 - page 11

    WUX5000 / WUX4000 User Commands - 8 - 3. Communication Flow T ransmission sent At the PC, the transmission is se nt within character intervals of T c (character interval timeout). T ransmission received At the Projector , the data that is able to be received within the character interval of T c is held, and the transmission is considered received w ...

  • Canon WUX5000 - page 12

    WUX5000 / WUX4000 User Commands - 9 - 4. Command System ...

  • Canon WUX5000 - page 13

    WUX5000 / WUX4000 User Commands - 10 - ...

  • Canon WUX5000 - page 14

    WUX5000 / WUX4000 User Commands - 1 1 - 5. Command List Item Commands Description 1 6AXADJ 6-axis adjustment ON / OFF 2 6AXR-Y 6-axis correction R-Y hue / saturation settings 3 AMBADJ Ambient light correction adjustment ON / OFF 4 AMBLEVEL Ambient li ght level settings 5 AMBTYPE Ambient light type settings 6 ASPECT Screen settings 7 AUTOPC Auto PC ...

  • Canon WUX5000 - page 15

    WUX5000 / WUX4000 User Commands - 12 - Item Commands Description 36 NR Noise reduction 37 POWER This controls the power supply 38 PRODCODE Product information inquiry 39 RC Remote control operation emu late 40 RGBGAIN RGB gain a djustment 41 RGBOFFSET RGB offset adjustment 42 ROMVER ROM version inquiry 43 SAT Color satura tion setting 44 SAVEIMGPRO ...

  • Canon WUX5000 - page 16

    WUX5000 / WUX4000 User Commands - 13 - 6. Details of Commands Descriptions of each comm and are prov ided starting from the next page. The command descriptions have the format s hown below . Alphabetic command name This briefly describes the command functi on. Format This indicates the command format. Environment This defines the environments that ...

  • Canon WUX5000 - page 17

    WUX5000 / WUX4000 User Commands - 14 - 6AXADJ 6-axis adjustment ON / OFF Format 6AXADJ=<6-axis adjustment parameter : ID> GET □ 6AXADJ / ? △ 6AXADJ <6-axis adjustmen t parameter:ID> ON This sets the 6-axis adjustment to ON. OFF This sets the 6-axis adjustment to OFF . Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O ...

  • Canon WUX5000 - page 18

    WUX5000 / WUX4000 User Commands - 15 - 6AXR-Y 6-axis correction R-Y hu e / saturation settings Format 6AXR=<R hue:Number> ▽ <R saturation:Number> ▽ <R brightness:Number> 6AXG=<G hue:Number> ▽ <G saturation:Number> ▽ <G brightness:Number> 6AXB=<B hue:Number> ▽ <B saturation:Number> ▽ <B ...

  • Canon WUX5000 - page 19

    WUX5000 / WUX4000 User Commands - 16 - AMBADJ Ambient light correction adjustment ON / OFF Format AMBADJ=<Ambient light correction adjustment parameter:ID> GET □ AMBADJ / ? △ AMBADJ <Ambient light correction adj ustment parameter:ID> ON This sets the ambient light correction adjustment to ON. OFF This sets the ambient light correcti ...

  • Canon WUX5000 - page 20

    WUX5000 / WUX4000 User Commands - 17 - AMBLEVEL Ambient light level settings Format AMBLEVEL=<Ambient light level settings parameter:ID> GET □ AMBLEVEL / ? △ AMBLEVEL <Ambient light level settings parameter:ID> WEAK This sets the ambient light level to WEAK. MIDDLE This s ets the ambient light level to MIDDLE. STRONG This sets the a ...

  • Canon WUX5000 - page 21

    WUX5000 / WUX4000 User Commands - 18 - AMBTYPE Ambient light type settings Format AMBTYPE=<Ambient light type settings parameter:ID> GET □ AMBTYPE / ? △ AMBTYPE <Ambient light type settings parameter: ID> TG This sets the ambient light type to T ungsten. FL This sets the ambient light type to Fluorescent. FL_H This sets the ambient ...

  • Canon WUX5000 - page 22

    WUX5000 / WUX4000 User Commands - 19 - ASPECT Screen settings Format ASPECT=<Screen setting parameters:ID> GET □ ASPECT / ? △ ASPECT <Screen setting parameters:ID> AUTO Auto 4:3 4:3 16:9 16:9 ZOOM Zoom TRUE Real FULL Full screen Environment Power Input OFF ON PM Parameter D-RGB A-RGB HDMI None X O X AUTO ○ ○ ○ *3 4:3 ○ ○ ? ...

  • Canon WUX5000 - page 23

    WUX5000 / WUX4000 User Commands - 20 - Example Setting > ASPECT=16:9 This sets the screen size to 16:9. < i:OK Reference > GET ASPECT or ?ASPECT This retrieves the screen size. < g:ASPECT=TRUE * Commands are indicated by ">", and responses are indicated by "<". ...

  • Canon WUX5000 - page 24

    WUX5000 / WUX4000 User Commands - 21 - AUTOPC Auto PC Format AUTOPC △ Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X X O X X X Response "i:OK" is returned if the control was executed properly . For details on other response s, refer to the "Error Lis t". Description (1) This executes Auto PC. (2) This comma ...

  • Canon WUX5000 - page 25

    WUX5000 / WUX4000 User Commands - 22 - AUTOSETEXE Auto setup Format AUTOSETEXE □ <Auto set parameter:ID> <Auto set parameter:ID> INPUT Automatic signal sensing execution Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response  i:OK” is returned when the automatic processing was completed successfully . For d ...

  • Canon WUX5000 - page 26

    WUX5000 / WUX4000 User Commands - 23 - AV O L Audio volume adjustment Format AVOL=<Audio volume level:Number> GET □ AVOL / ? △ AVOL Setting values for <Audio volu me level:Number> are 0 to 20. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly ...

  • Canon WUX5000 - page 27

    WUX5000 / WUX4000 User Commands - 24 - BLANK BLANK function Format BLANK=<BLANK parameter:ID> GET □ BLANK / ? △ BLANK <BLANK parameter:ID> ON BLANK ON OFF BLANK OFF Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For ' GET BLANK &apos ...

  • Canon WUX5000 - page 28

    WUX5000 / WUX4000 User Commands - 25 - BRI Brightness setting Format BRI=<Brightness setting:Number> GET □ BRI / ? △ BRI Setting values for <Brightness setting: Number> are -20 to 20. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For &ap ...

  • Canon WUX5000 - page 29

    WUX5000 / WUX4000 User Commands - 26 - COLOR_TEMP Color temperature setting Format COLOR_TEMP=<Color temperature setting:Number> GET □ COLOR_TEMP / ? △ COLOR_TEMP Setting values for <Color temperat ure setting:Number> are -17 to 21. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is ret ...

  • Canon WUX5000 - page 30

    WUX5000 / WUX4000 User Commands - 27 - COMVER User command version inquir y Format GET □ COMVER / ? △ COMVER Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response Returns the user command version as g:COMVER="<User command version:Character string>" For details on other response s, refer to the "Error Li ...

  • Canon WUX5000 - page 31

    WUX5000 / WUX4000 User Commands - 28 - CONT Contrast setting Format CONT=<Contrast setting:Number> GET □ CONT / ? △ CONT Setting values for <Contrast setting:Number > are -20 to 20. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For &apos ...

  • Canon WUX5000 - page 32

    WUX5000 / WUX4000 User Commands - 29 - DGAMMA Dynamic gamma Format DGAMMA=<Dynamic gamma setting parameter:ID> GET □ DGAMMA / ? △ DGAMMA <Dynamic gamma setting parameter:ID> OFF Off WEAK W eak MIDDLE Middle STRONG Strong Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the ...

  • Canon WUX5000 - page 33

    WUX5000 / WUX4000 User Commands - 30 - DZOOM_POS DZOOM position setting Format DZOOM_POS=<DZOOM position X:Number>,<DZOOM position Y:Number> GET □ DZOOM_POS / ? △ DZOOM_POS <DZOOM p osition X / Y :Number> is a signe d integer indica ting the central po sition of the en larged inpu t image. Environment Power Input OFF ON PM D-R ...

  • Canon WUX5000 - page 34

    WUX5000 / WUX4000 User Commands - 31 - DZOOM_RA T DZOOM ratio setting Format DZOOM_RAT=<DZOOM ratio parameter:ID> GET □ DZOOM_RAT / ? △ DZOOM_RAT <DZOOM ratio parameter:ID> 1 same size (DZOOM disabled) 1.5 1.5x 2 2x 3 3x 4 4x 5 5x 6 6x 8 8x 10 10x 12 12x Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X O O O O X Re ...

  • Canon WUX5000 - page 35

    WUX5000 / WUX4000 User Commands - 32 - ERR Error information inquiry Format GET □ ERR / ? △ ERR Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response Returns the current erro r information as 'g:ERR=<ErrorID:Character string>' For details on other response s, refer to the "Error Lis t". <ErrorID: ...

  • Canon WUX5000 - page 36

    WUX5000 / WUX4000 User Commands - 33 - FINE_GAMMA_R Fine gamma (R) adjustment Format FINE_GAMMA_R=<Fine gamma (R) adjustment point 1 adjustment value:Number>, <Fine gamma (R) adjustment point 2 adjustment value:Number>, ・・・ ,<Fine gamma (R) adjustment point n adjustment value:Number> GET □ FINE_GAMMA_R / ? △ FINE_GAMMA_R ...

  • Canon WUX5000 - page 37

    WUX5000 / WUX4000 User Commands - 34 - FINE_GAMMA_G Fine gamma (G) adjustment Format FINE_GAMMA_G=<Fine gamma (G) adjustment point 1 adjustment value:Number>, <Fine gamma (G) adjustment point 2 adjustment value:Number>, ・・・ ,<Fine gamma (G) adjustment point n adjustment value:Number> GET □ FINE_GAMMA_G / ? △ FINE_GAMMA_G ...

  • Canon WUX5000 - page 38

    WUX5000 / WUX4000 User Commands - 35 - FINE_GAMMA_B Fine gamma (B) adjustment Format FINE_GAMMA_B=<Fine gamma (B) adjustment point 1 adjustment value:Number>, <Fine gamma (B) adjustment point 2 adjustment value:Number>, ・・・ ,<Fine gamma (B) adjustment point n adjustment value:Number> GET □ FINE_GAMMA_B / ? △ FINE_GAMMA_B ...

  • Canon WUX5000 - page 39

    WUX5000 / WUX4000 User Commands - 36 - FREEZE Freeze status Format FREEZE=<FREEZE parameter:ID> GET □ FREEZE / ? △ FREEZE <FREEZE parameter:ID> ON Image now frozen OFF Image now not frozen Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X O O O O X Response "i:OK" is returned if the parameter was set prope ...

  • Canon WUX5000 - page 40

    WUX5000 / WUX4000 User Commands - 37 - GAMMA Gamma adjustment Format GAMMA=<Gamma adjustment:Number> GET □ GAMMA / ? △ GAMMA Setting values for <Gamma adjustment: Number > are -10 to 10. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For ...

  • Canon WUX5000 - page 41

    WUX5000 / WUX4000 User Commands - 38 - HDMI_IN HDMI input setting Format HDMI_IN=<HDMI input setting parameter:ID> GET □ HDMI_IN / ? △ HDMI_IN <HDMI input setting parameter:ID> AUTO Select this when connectin g to an A V equipment. Image processing and menu displays are adjusted r espective to the connected video equipment. PC Selec ...

  • Canon WUX5000 - page 42

    WUX5000 / WUX4000 User Commands - 39 - HDMI_OVSCAN HDMI overscan setting Format HDMI_OVSCAN=<HDMI overscan setting parameter:ID> GET □ HDMI_OVSCAN / ? △ HDMI_OVSCAN <HDMI overscan setting parameter:ID> OFF T urns overscan to OFF ON T urns overscan to ON Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - - - O O Res ...

  • Canon WUX5000 - page 43

    WUX5000 / WUX4000 User Commands - 40 - HUE Hue setting Format HUE=<Hue setting value:Number> GET □ HUE / ? △ HUE Setting values for <Hue setting value:Number> are -20 to 20. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For ' GET HU ...

  • Canon WUX5000 - page 44

    WUX5000 / WUX4000 User Commands - 41 - IMAGE Image mode setting Format IMAGE=<Image mode setting parameter:ID> GET □ IMAGE / ? △ IMAGE <Image mode setting parameter:ID> ST ANDARD Standard PRESENT A TI ON Presentation VIVID_PHOTO V ivid photo PHOTO_SRGB Photo / sRGB DCM_SIM DICOM Sim* DYNAMIC Dynamic VIDEO V ideo CINEMA Cinema USER_1 ...

  • Canon WUX5000 - page 45

    WUX5000 / WUX4000 User Commands - 42 - Setting Commands related to the settings 6-axis adjustment 6AXADJ 6-axis color correction 6AXR ∼ Y (5) The current image quality can be acquired using the applicable GET c ommand. (" GET IMAGE ") Example Setting > IMAGE=PRESENTATION This sets the image mode to "Presentation". < i:OK ...

  • Canon WUX5000 - page 46

    WUX5000 / WUX4000 User Commands - 43 - IMAGEFLIP Flip display Format IMAGEFLIP=<Image flip setting parameters:ID> GET □ IMAGEFLIP / ? △ IMAGEFLIP <Image flip setting parameters:ID> NONE None CEILING Ceiling REAR Rear projection REAR_CEILING Rear proj ection with ceiling Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X ...

  • Canon WUX5000 - page 47

    WUX5000 / WUX4000 User Commands - 44 - INPUT Input selection Format INPUT=<Input selection parameters:ID> GET □ INPUT / ? △ INPUT <Input selection parameters:ID> D-RGB Digital PC A-RGB Analog PC COMP Component HDMI HDMI Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the ...

  • Canon WUX5000 - page 48

    WUX5000 / WUX4000 User Commands - 45 - LAMP Lamp output setting Format LAMP=<Lamp output setting parameters:ID> GET □ LAMP / ? △ LAMP <Lamp output setting parameters:ID> NORMAL Normal SILENT Silent cooling Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was ...

  • Canon WUX5000 - page 49

    WUX5000 / WUX4000 User Commands - 46 - LAMPCOUNTER Lamp ON time inquiry Format GET □ LAMPCOUNTER / ? △ LAMPCOUNTER Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response Returns current lamp on time as ' g:LAMPCOUNTER="<Lamp ON time:Character string>" ' For details on other response s, refer to the & ...

  • Canon WUX5000 - page 50

    WUX5000 / WUX4000 User Commands - 47 - MAIN Front panel operation emulation Format MAIN □ <Main unit panel emulation button parameters:ID> <Main unit panel emulation button para meters:ID> POWER POWER button POWER_OFF POWER bu tton pressed twice MENU MENU LENS LENS INPUT INPUT UP UP UP+REP Hold down the UP button *-REP Release the but ...

  • Canon WUX5000 - page 51

    WUX5000 / WUX4000 User Commands - 48 - MEMCADJ Memory color adjustment Format MEMCADJ=<Memory color adjustment parameter:ID> GET □ MEMCADJ / ? △ MEMCADJ <Memory color adjustment parameter:ID> OFF No adjustment MEM_L Memory color adjustment - light MEM_M Memory color adjustment - medium MEM_H Memory color adjustment - heavy Environme ...

  • Canon WUX5000 - page 52

    WUX5000 / WUX4000 User Commands - 49 - MODE Control mode switch Format REMOTE LOCAL GET □ MODE / ? △ MODE Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response "i:OK" is always returned with the cont rol mode switch setting. For ' GET MODE ' or ' ?MODE ', current co ntrol mode is returned as &ap ...

  • Canon WUX5000 - page 53

    WUX5000 / WUX4000 User Commands - 50 - MUTE Mute control Format MUTE=<Mute control parameter: ID> GET □ MUTE / ? △ MUTE <Mute control para meter: ID> ON This prohibits the audio / beep sound. OFF This permits the audio / beep sound. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is ret ...

  • Canon WUX5000 - page 54

    WUX5000 / WUX4000 User Commands - 51 - NR Noise reduction Format NR=<Noise reduction setting parameter:ID> GET □ NR / ? △ NR <Noise reduction setting pa rameter:ID> OFF Off WEAK W eak MIDDLE Middle STRONG Strong Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X X X O O O Response "i:OK" is returned if nois ...

  • Canon WUX5000 - page 55

    WUX5000 / WUX4000 User Commands - 52 - POWER This controls the power supply Format POWER □ <Parameter:ID> GET □ POWER / ? △ POWER <Parameter:ID> ON Power ON OFF Power OFF Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response "i:OK" is returned if the parameter was set properly . For ' GET POWER & ...

  • Canon WUX5000 - page 56

    WUX5000 / WUX4000 User Commands - 53 - PRODCODE Product information inquiry Format GET □ PRODCODE / ? △ PRODCODE Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response Product name is returned as g:PRODCODE="<Product name:Character string>" For details on other response s, refer to the "Error Lis t". ...

  • Canon WUX5000 - page 57

    WUX5000 / WUX4000 User Commands - 54 - RC Remote control operation emu late Format RC □ <Remote control emulation button parameters:ID> <Remote control emulatio n button parameters:ID> POWER POWER button POWER_OFF POWER bu tton pressed twice MENU MENU INPUT INPUT ASPECT ASPECT AUTOPC AUTOPC KEYSTONE KEYSTONE UP UP UP+REP Hold down the ...

  • Canon WUX5000 - page 58

    WUX5000 / WUX4000 User Commands - 55 - Response "i:OK" is returned when the button press re quest has been acknowledged successfully . (It does not indicate if the operation for the pressed button was executed properly .) Description (1) This emulates pressing of the remote control buttons for controlling the projector . (2) W ith the emu ...

  • Canon WUX5000 - page 59

    WUX5000 / WUX4000 User Commands - 56 - RGBGAIN RGB gain adjustment Format RGBGAIN=<R gain setting:Number> ▽ <G gain setting:Number> ▽ <B gain setting:Number> GET □ RGBGAIN / ? △ RGBGAIN Setting values for <R/G/B gain setting:Number> are -60 to 60. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - R ...

  • Canon WUX5000 - page 60

    WUX5000 / WUX4000 User Commands - 57 - RGBOFFSET RGB offset adjustment Format RGBOFFSET=<R offset setting:Number> ▽ <G offset setting:Number> ▽ <B offset setting:Number> GET □ RGBOFFSET / ? △ RGBOFFSET Setting values for <R/G/B offset setting:Number > are -60 to 60. Environment Power Input OFF ON PM D-RGB A-RGB COMP ...

  • Canon WUX5000 - page 61

    WUX5000 / WUX4000 User Commands - 58 - ROMVER ROM version inquiry Format GET □ ROMVER / ? △ ROMVER Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response ROM version of the firmwa re is returned as g:ROMVER="<ROM version:Character string>" For details on other response s, refer to the "Error Lis t". ...

  • Canon WUX5000 - page 62

    WUX5000 / WUX4000 User Commands - 59 - SA T Color saturati on setting Format RGBGAIN=<R gain setting:Number> ▽ <G gain setting:Number> ▽ <B gain setting:Number> GET □ RGBGAIN / ? △ RGBGAIN Setting values for <Color saturation setting value:Number> are -20 to 20. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI ...

  • Canon WUX5000 - page 63

    WUX5000 / WUX4000 User Commands - 60 - SA VEIMGPROF Create, save, delete user memory / Create user memory s tatus Format SAVEIMGPROF=<User memory save to parameter:ID> <User memory save to parameter:ID> USER_1 Save to User 1 USER_2 Save to User 2 USER_3 Save to User 3 USER_4 Save to User 4 USER_5 Save to User 5 DEL_ALL Delete all User m ...

  • Canon WUX5000 - page 64

    WUX5000 / WUX4000 User Commands - 61 - SCRNASPECT Screen aspect setting Format SCRNASPECT=<Screen aspect setting parameter:ID> GET □ SCRNASPECT / ? △ SCRNASPECT <Screen aspect setting parameter:ID> 16:10 16:10 16:9 16:9 display 4:3 4:3 display 16:9_DIS 16:9 dig ital image shift 4:3_DIS 4:3 digital image shift Environment Power Input ...

  • Canon WUX5000 - page 65

    WUX5000 / WUX4000 User Commands - 62 - SEL Input signal selection Format SEL=<Input signal selection parameter:ID> GET □ SEL / ? △ SEL <Input signal selection parameter:ID> AUTO Auto Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X X X O X X Response "i:OK" is returned if the parameter was set properly . ...

  • Canon WUX5000 - page 66

    WUX5000 / WUX4000 User Commands - 63 - SHARP Sharpness setting Format SHARP=<Sharpness setting:Number> GET □ SHARP / ? △ SHARP Setting values for <Shar pness setting:Number> are -10 to 10. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . Fo ...

  • Canon WUX5000 - page 67

    WUX5000 / WUX4000 User Commands - 64 - SIGNAL_INFO Input signal information inquiry Format GET □ SIGNAL_INFO / ? △ SIGNAL_INFO Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response Current input si gnal information is returned as ' g:SIGNAL_INFO="<Input signal information:Character string>" ' Fo ...

  • Canon WUX5000 - page 68

    WUX5000 / WUX4000 User Commands - 65 - SIGNALST A TUS Signal status inquiry Format GET □ SIGNALSTATUS / ? △ SIGNALSTATUS Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response Current image sign al input status is retur ned as 'g:SIGNALSTATUS=<Signal status:ID>' For details on other response s, refer to th ...

  • Canon WUX5000 - page 69

    WUX5000 / WUX4000 User Commands - 66 - TEMP T emperature sensor value inquiry Format GET □ TEMP / ? △ TEMP Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response For ' GET TEMP ' or ' ?TEMP ', temperature sensor value is returned as ' TEMP=<Number of sensors>,<Sensor 1 value>,…,<Senso ...

  • Canon WUX5000 - page 70

    WUX5000 / WUX4000 User Commands - 67 - 7. Error List Item Code TY PE Error character strings Error Remedy 1 0001 e BAD_SEQUENCE Communication sequence err or Wait until a response is receiv ed before sending the next command. 2 0002 e INVALID_COMMAND Invalid (undefined) command. Send a va lid command. 3 0004 e INVALID_FORMAT Invalid command format. ...

  • Canon WUX5000 - page 71

    WUX5000 / WUX4000 User Commands - 68 - Item Code TY PE Error character strings Error Remedy 201F e INVALID_SIGNAL Cannot execute command with current input signal. Change the input signal. 17 0801 e INVALID_VALUE Numerical parameters are invalid or outside the specified range. Set the parameters in the correct range. 18 1002 e NO_LOGO_CAPTURED Cann ...

  • Canon WUX5000 - page 72

    WUX5000 / WUX4000 User Commands - 69 - 8. Error Processing YES YES YES YES YES YES YES YES YES YES YES YES YES YES Error judgment START Invalid command format? "INVALID_FORMAT" Command executable while power mode is OFF? Power mode is "OFF"? "NOT_POWER_SUPPLIED" Internal processing in progress? "BUSY" Process ...

  • Canon WUX5000 - page 73

    WUX5000 / WUX4000 User Commands - 70 - YES YES YES YES NO YES YES Incorrect input source? "INVALID_SOURCE (**)" Limitations in input source? Requires input signal? No input signal? "NO_SIGNAL" Numerical parameter outside the specified range? "INVALID_VALUE" User command is executable FINISHED Invalid input signal? &quo ...

  • Canon WUX5000 - page 74

    WUX5000 / WUX4000 User Commands - 71 - 9. Other Use the remote control emulation function (RC command) for the following functions. Function PC command parameter Presentation timer P_T IMER ...

Manufacturer Canon Category Projector

Documents that we receive from a manufacturer of a Canon WUX5000 can be divided into several groups. They are, among others:
- Canon technical drawings
- WUX5000 manuals
- Canon product data sheets
- information booklets
- or energy labels Canon WUX5000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Canon WUX5000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Canon WUX5000, service manual, brief instructions and user manuals Canon WUX5000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Canon WUX5000.

Similar manuals

A complete manual for the device Canon WUX5000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Canon WUX5000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Canon WUX5000.

A complete Canon manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Canon WUX5000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Canon WUX5000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Canon WUX5000, that we can find in the current document
3. Tips how to use the basic functions of the device Canon WUX5000 - which should help us in our first steps of using Canon WUX5000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Canon WUX5000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Canon WUX5000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Canon WUX5000?

Use the form below

If you did not solve your problem by using a manual Canon WUX5000, ask a question using the form below. If a user had a similar problem with Canon WUX5000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)