Manual Ryobi A25RT02

20 pages 4.72 mb
Download

Go to site of 20

Summary
  • Ryobi A25RT02 - page 1

    OPERA TOR’S MANUAL ROUTER T ABLE A25R T02 Inch 1 0 1 2 3 Inch 1 0 1 2 3 inch SA VE THIS MANUAL FOR FUTURE REFERENCE Y our router table has been engineer ed and manufactured to our high standar d for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-free performance. WARNI ...

  • Ryobi A25RT02 - page 2

    2 T ABLE OF CONTENTS  Introduction ..................................................................................................................................................................... 2  W arranty .................................................................................................................................. ...

  • Ryobi A25RT02 - page 3

    3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury . READ ALL INSTRUCTIONS  KNOW YOUR POWER TOOL. Car efully read the router table operator’ s manual and the manual for the particular router you are using. Lear ...

  • Ryobi A25RT02 - page 4

    4 GENERAL SAFETY RULES  INSPECT TOOL CORDS PERIODICALL Y . I f dam aged, hav e rep air ed by a qua lif ied ser vic e tech nic ian at an auth ori zed serv ice facil ity . The cond uctor with ins ula tion having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor . If repair or replacement of the elec ...

  • Ryobi A25RT02 - page 5

    5 SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Pr oper interpretation of these symbols will allow you to operate the pr oduct better and safer . V V olts V oltage A Amperes Current Hz Hertz Frequency (cycles per second) W W att Power min Minutes Time Alternating Current T ype of curre ...

  • Ryobi A25RT02 - page 6

    6 SYMBOLS SERVICE Servicing requir es extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you r etur n the pr oduct to the near est AUTHORIZED SERVICE CENTER for repair . When servic- ing, use only identical replacement parts. WARNING: T o avoi d ser ious pers onal inju ry , do not atte ...

  • Ryobi A25RT02 - page 7

    7 ELECTRICAL SPEED AND WIRING The no-load speed of this product depends on the router you are using. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’ s horsepower rating. A line intended only for lights cannot properly carry a power product motor . Wire th ...

  • Ryobi A25RT02 - page 8

    8 Inch 1 0 1 2 3 Inch 1 0 1 2 3 inch FEED DIRECTION 1 Inch FEA TURES PRODUCT SPECIFICA TIONS T able Dimensions ................................ 16 in. x 32 in. x 1 in. Maximum Cutter Diameter ................................. 1-15/16 in. Fence Length ............................................................. 28 in. KNOW YOUR ROUTER T ABLE See Fi ...

  • Ryobi A25RT02 - page 9

    9 FEA TURES RESET BUTTON See Figure 2. The r outer table switch is e quipped with a reset button that protects the electronic components of the r outer table switch box from overload. ST ARTING PIN When you are unable to use the fence for a guide because the workpiece is odd-shaped or too small, use the starting pin for a guide and/or pivot point. ...

  • Ryobi A25RT02 - page 10

    10 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION 3 ASSEMBL Y P ACKING LIST 1. T able Leg (4) 2. Starting Pin 3. T able Leg Phillips Head Screw (16) 4. T able T op 5. Switch Box Nut (3) 6. Switch Box Screw (3) 7. Switch Box 8. Carriage Bolt W asher (2) 9. Carriage Bolt (2) 10. Hex Key (1) 11. Under T able Guard (2) 12. Throat Plates (5) 13. Router In ...

  • Ryobi A25RT02 - page 11

    11 ASSEMBL Y ASSEMBLING THE ROUTER T ABLE Assembl ing the ro uter table involves attaching the switch box, the under table guards, the legs, the router/insert plate as- sem bly , the fe nce ass embl y , feat herb oar d, thr oat pla te, sta rti ng pin, and installing the miter gauge to the router table. A TT ACHING THE SWITCH BOX See Figure 5. The s ...

  • Ryobi A25RT02 - page 12

    12 ASSEMBL Y PRE-DRILLING HOLES FOR THROUGH T ABLE DEPTH ADJUSTMENT See Figure 8. Since each router will have differ ent placements for through table depth adjustments, pilot holes have been pre-drilled in the throat plate to assist in thr ough table adjustments. Only the models listed below in the key are available for use with the through table d ...

  • Ryobi A25RT02 - page 13

    13 ASSEMBL Y BRAND MODEL BASE TYPE F ASTENER SIZE INSERT PLA TE HOLES USED NUMBER OF HOLES Bosch 1617 Fixed 10-24 x 5/8 in. A1, A3, A5 3 Bosch 1617 EVS Fixed 10-24 x 5/8 in. A1, A3, A5 3 Bosch 1617 EVSPK Fixed 10-24 x 5/8 in. A1, A3, A5 3 Craftsman 17504 Fixed 10-32 x 5/8 in. A2, A4, A6 3 Craftsman 17505 Fixed 10-32 x 5/8 in. A2, A4, A6 3 Craftsman ...

  • Ryobi A25RT02 - page 14

    14 MAKING INSERT PLA TE LEVEL See Figure 12.  Unplug the router table and/or the r outer .  Check to see if the insert plate mount ed assemb ly is level with a straight edge or level.  Loosen insert plate screws.  Usin g the sup pli ed hex key , tigh ten or loo sen the ad just - ing scr ews depen din g on how the inse rt pla te needs to ...

  • Ryobi A25RT02 - page 15

    15 Inch 1 0 1 2 3 Inch 1 0 1 2 3 ASSEMBL Y Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION ST ARTING PIN HOLES ST ARTING PIN INST ALL REMOVE Fig. 16 SLOT FEA THERBOARD BOL T CARRIAGE BOL T WASHER FENCE LOCK KNOB FEED DIRECTION Inch 1 0 1 2 3 Inch 1 0 1 2 3 Fig. 17 MITER GAUGE SLOT MITER GAUGE BAR POINTER FEA THERBOARD Fig. 15  Unplug the router tab ...

  • Ryobi A25RT02 - page 16

    16 Inch 1 0 1 2 3 Inch 1 0 1 2 3 inch Inch 1 0 1 2 3 Inch 1 0 1 2 3 inch FEED DIRECTION 1 Inch ASSEMBL Y A TT ACHING THE V ACUUM HOSE See Figure 18. The vacuum port molded into the fence will accept either a 1-1/4 in. or 2-1/2 in. vacuum attachment. CLAMPING THE ROUTER T ABLE TO A WORK BENCH See Figures 19.  Unplug the router table and/or the r ...

  • Ryobi A25RT02 - page 17

    17 OPERA TION PERFORMING A ROUTING OPERA TION Observe the following rules when using the router .  Read the entir e operator’ s manual for the r outer and router table.  Plug the router table power cor d into a power source.  Always contr ol the power to the router with the router table switch whenever the r outer is mounted on the table ...

  • Ryobi A25RT02 - page 18

    18 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION 2 3 FEED DIRECTION 1 Inch Inch 1 0 1 2 3 Inch 1 0 1 2 3 OPERA TION INSERTING/REMOVING CUTTERS  Unplug the router table and/or the r outer .  Remove the router/insert plate assembly . (See Installing Router/Insert Plate Assembly in the Assembly section.) WARNING: If you are changing a cutter imme ...

  • Ryobi A25RT02 - page 19

    19 MAINTENANCE WARNING: Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury . Electric tools used on fiberglass material, wallboard, spack - ling compounds, or plaster are subj ...

  • Ryobi A25RT02 - page 20

    20 OPERA TOR’S MANUAL ROUTER T ABLE A25R T02 987000-115 03-20-07 (REV :01) A25RT02 • P AR TS AND SERVICE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the pr oduct data plate. • MODEL NUMBER • SERIAL NUMBER • HOW TO OBT AIN REPLACEMENT P AR TS: Replacement parts can be purchas ...

Manufacturer Ryobi Category Router

Documents that we receive from a manufacturer of a Ryobi A25RT02 can be divided into several groups. They are, among others:
- Ryobi technical drawings
- A25RT02 manuals
- Ryobi product data sheets
- information booklets
- or energy labels Ryobi A25RT02
All of them are important, but the most important information from the point of view of use of the device are in the user manual Ryobi A25RT02.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Ryobi A25RT02, service manual, brief instructions and user manuals Ryobi A25RT02. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Ryobi A25RT02.

Similar manuals

A complete manual for the device Ryobi A25RT02, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Ryobi A25RT02 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Ryobi A25RT02.

A complete Ryobi manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Ryobi A25RT02 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Ryobi A25RT02, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Ryobi A25RT02, that we can find in the current document
3. Tips how to use the basic functions of the device Ryobi A25RT02 - which should help us in our first steps of using Ryobi A25RT02
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Ryobi A25RT02
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Ryobi A25RT02 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Ryobi A25RT02?

Use the form below

If you did not solve your problem by using a manual Ryobi A25RT02, ask a question using the form below. If a user had a similar problem with Ryobi A25RT02 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)