Manual Vector VEC093

12 pages 0.23 mb
Download

Go to site of 12

Summary
  • Vector VEC093 - page 1

    1 AUTOMA TIC BA TTER Y CHARGER OWNER’S MANUAL & W ARRANTY INFORMA TION 12 VOL T 2/1 0/20/40 AMPERE CHARGE RA TES WITH 1 00 AMP ENGINE ST AR T , AL TERNA TOR VOL T AGE CHECK AND BA TTERY RECONDITON FUNCTIONS • IMPORT ANT SAFETY INSTRUCTIONS • W ARNING – RISK OF EXPLOSIVE GASES 1. WORKING IN VICINITY OF A LEAD-ACID BA TTER Y IS DANGEROUS. ...

  • Vector VEC093 - page 2

    2 PERSONAL PRECAUTIONS AND SAFETY 1. Someone should be within range of your voice or close enough to come to your aid when you work near a lead-acid batter y . 2. Have plenty of fresh water and soap nearby in case batter y acid contacts skin, clothing, or eyes. 3. W ear complete eye protection and clothing protection. Avoid touching eyes while work ...

  • Vector VEC093 - page 3

    3 PREP ARING TO CHARGE 1. Determine voltage of batter y by referring to car owner's manual. 2. If it is necessar y to remove batter y from vehicle to charge, or to clean terminals, always remove grounded terminal from batter y first. Make sure all accessories in the vehicle are off, so as not to cause an arc. 3. Clean batter y ter minals. Be c ...

  • Vector VEC093 - page 4

    4 INTRODUCTION AND FEA TURES Thank you for selecting the V ector(r) Model VEC093 2/1 0/20/40 Amp 12 volt Smart Batter y Charger with Engine Start, Alter nator V oltge Check and Batter y Restore modes. With proper care and use, it will give you years of depend- able ser vice. This model batter y charger has a high charge rate of up to 40 amps, and l ...

  • Vector VEC093 - page 5

    5 FIGURE 3A (FRONT VIEW) FIGURE 3B (REAR VIEW) W ARNINGS: • THERE ARE NO USER-SERVICEABLE P AR TS IN THIS UNIT . IN THE EVENT OF ANY OPERA TING PROBLEM THA T THE UNIT'S BUIL T -IN CIRCUIT PROTECTION CAN NOT HANDLE. • DO NOT OPEN THE UNIT . IT MUST BE RETURNED TO VECTOR FOR PROFESSIONAL TESTING AND REP AIR. OPENING THE UNIT WILL VOID THE MA ...

  • Vector VEC093 - page 6

    6 INDICA TORS THE LARGE 3-CHARACTER DIGIT AL DISPLA Y in the upper left hand corner of the panel indicates many conditions. It indicates when AC power is applied to the charger , actual charge rate in amperes, when the batter y is fully charged, detected faults, operating modes and when the charger is ready for the next mode selection. What is disp ...

  • Vector VEC093 - page 7

    7 CHARGE RA TE SELECTION VEC093 After the clamps are connected, plug in the charger to an AC outlet and the charger will show a circulating pattern on the Digital Display . This pattern indicates power is applied. Press the ON/OFF button to prepare the charger to change to an operating mode. Press the 2/1 0/20/40 A button and the charger will begin ...

  • Vector VEC093 - page 8

    8 CONNECTING IF BA TTER Y IS OUTSIDE OF VEHICLE a) Check polarity of batter y posts- For top-mounted batter y connectors, the positive post (marked POS, P , +) usually has a larger diameter than the Negative batter y post (marked NEG, N, –). For side-mounted batter y connections the Positive terminal is red, the Negative terminal is black. b) Att ...

  • Vector VEC093 - page 9

    9 This slowly (over 24 hours) removes the insulating buildup from the plates so the batter y can hold a full charge. Most automotive batteries (50 to 70AH) can be treated once to reduce the lead sulfate buildup. Smaller 12 volt batteries, such as found in jump starters can be treated for 12 hours. However , depending on the severity of lead sulfate ...

  • Vector VEC093 - page 10

    10 TROUBLESHOOTING - F AUL T LED LIT NOTE: Batteries below 4.0 V olts will not allow the charger to operate. Make sure the batter y has at least 4 V olts if charger will not charge. The following conditions may light the F AULT LED: • Poor connection to the batter y (or frame). • Charging too fast - Decrease Charge Rate - Press 2/1 0/20/40A Pus ...

  • Vector VEC093 - page 11

    11 APPENDIX A — CHARGING TIMES To calculate the approximate charging time required to fully charge a batter y , it is necessar y to determine the specific gravity (or , percent of batter y charge) using a hydrometer . Use this technique if batter y vent caps can be removed. Check each cell. If there is one cell with a ver y low specific gravity c ...

  • Vector VEC093 - page 12

    12 VECTOR 5 YEAR LIMITED W ARRANTY PROGRAM This limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of V ector Manufacturing, Ltd., regarding this product. There is no other warranty , other than described herein. This V ector Manufacturing, Ltd. product is warranted, to the original pur ...

Manufacturer Vector Category Automobile Battery Charger

Documents that we receive from a manufacturer of a Vector VEC093 can be divided into several groups. They are, among others:
- Vector technical drawings
- VEC093 manuals
- Vector product data sheets
- information booklets
- or energy labels Vector VEC093
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vector VEC093.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vector VEC093, service manual, brief instructions and user manuals Vector VEC093. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vector VEC093.

A complete manual for the device Vector VEC093, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vector VEC093 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vector VEC093.

A complete Vector manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vector VEC093 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vector VEC093, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vector VEC093, that we can find in the current document
3. Tips how to use the basic functions of the device Vector VEC093 - which should help us in our first steps of using Vector VEC093
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vector VEC093
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vector VEC093 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vector VEC093?

Use the form below

If you did not solve your problem by using a manual Vector VEC093, ask a question using the form below. If a user had a similar problem with Vector VEC093 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (1)

Jose Antonio

Al intentar scanear me dice que conecte el scaner. Una y otra vez.