English dropdown-ico

Manual Makita BFL080F

16 pages 0.18 mb
Download

Go to site of 16

Summary
  • Makita BFL080F - page 1

    INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Cor dless Angle Nut Runner MODEL BFL080F MODEL BFL081F MODEL BFL120F MODEL BFL121F MODEL BFL200F 003614 ...

  • Makita BFL080F - page 2

    2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA003-1 (FOR All BA TTER Y OPERA TED T OOLS ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic sh ...

  • Makita BFL080F - page 3

    3 SA VE THESE INSTR UCTIONS Wo r k A r e a 1. Keep y our work area clean and well lit. Cluttered benches and dark areas invite acci- dents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Pow e r tools create sparks which may ignite the dust or fumes. 3. Keep bystander s, childre ...

  • Makita BFL080F - page 4

    4 18. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control. 19. Check f or misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’ s operation. If damaged, have the tool ser- viced befo ...

  • Makita BFL080F - page 5

    5 SYMBOLS USD301-1 The f ollowings show the symbols used f or tool. V ....................... volts ................... direct current .................... no load speed .../min ................ rev olutions or reciprocation per minute IMPOR T ANT SAFETY INSTR UCTIONS FOR CHARGER & B A TTER Y CAR TRIDGE USC002-3 1. SA VE THESE INSTRUCTIONS- Thi ...

  • Makita BFL080F - page 6

    6 11 . Do not disassemble charger or battery cartridge; take it to a qualified ser viceman when service or repair is required. Incor- rect reassembly ma y result in a risk of electric shock or fire. 12. T o reduce risk of electric shock, unplug charger fr om outlet before attempting any maintenance or cleaning. T urning off con- trols will not redu ...

  • Makita BFL080F - page 7

    7 SYMBOLS The f ollowing show the symbols used f or the charger . Be sure that you understand their meaning bef ore use. .......... Ready to charge ............. Charging ............. Charging complete ........... Delay charge (Cooling) ........ Def ective batter y .... Conditioning ........... Cooling abnormality ...

  • Makita BFL080F - page 8

    8 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed bef ore adjusting or checking function on the tool. Installing or removing battery cartridge • Alwa ys switch off the tool bef ore inser tion or remov al of the batter y cartr idge. For Models BFL080F , BFL120F • T o remo ...

  • Makita BFL080F - page 9

    9 3. Charge the batter y cartr idge with room temperature at 10 ° C - 40 ° C (50 ° F - 104 ° F). Let a hot batter y cartr idge cool do wn before charging it. 4. Charge the Nick el Metal Hydride batter y car tridge when you do not use it f or more than six months. 5. Alwa ys stop tool operation and charge the batter y car- tridge when you notice ...

  • Makita BFL080F - page 10

    10 Switch action CA UTION: • Bef ore inser ting the batter y car tridge into the tool, alwa ys check to see that the s witch trigger actuates properly and retur ns to the “ OFF ” position when released. T o star t the tool, simply pull the switch trigger . Release the s witch tr igger to stop . Rever sing switch action CA UTION: • Alwa ys c ...

  • Makita BFL080F - page 11

    11 LED indicator The lamp on the tool shows the f ollowing functions . 003814 Function Status Status of the LED indicator/beeper Action to be taken LED indicator Beeper Auto-stop f astening This function works when the tool has reached the preset fastening torque and normal tightening has been completed. This helps ov er tightening to be av oided. ...

  • Makita BFL080F - page 12

    12 Adjusting the fastening torque When you wish to driv e machine screws, wood scre ws, he x bolts, etc. with the predetermined torque, adjusting the f as- tening torque as fo llows. 1. First remov e the batter y car tridge from the tool. 2. Loosen the screws securing the light cov er . 3. Rotate the ring in the front of the tool by hand so that a ...

  • Makita BFL080F - page 13

    13 Installing or removing soc ket T o install the socket, push it onto the square drive of the tool with one hand by depressing a pin on the square driv e with another hand until it locks into place . T o remov e the sock et, simply pull it off depressing the pin on the square drive . OPERA TION Hold the tool fir mly and place the soc ket ov er the ...

  • Makita BFL080F - page 14

    14 NO TE: • The re volution angle means the angle which a screw/bolt re volv es when the tool attains to 100% from 50% of desired torque. • Use of a low temperature conditioned battery car tridge ma y sometimes give warning for battery car tridge capacity by w ar ning lamp and beeper which mak es the tool stop immediately . In this case, the r ...

  • Makita BFL080F - page 15

    15 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed before attempting to perf or m inspection or maintenance. Replacing carbon brushes Remov e and check the carbon brushes regularly . Replace when they we ar down to the limit mark. Keep the carbon brushes clean and free to slip in the h ...

  • Makita BFL080F - page 16

    Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita ’ s ...

Manufacturer Makita Category Work Light

Documents that we receive from a manufacturer of a Makita BFL080F can be divided into several groups. They are, among others:
- Makita technical drawings
- BFL080F manuals
- Makita product data sheets
- information booklets
- or energy labels Makita BFL080F
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita BFL080F.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita BFL080F, service manual, brief instructions and user manuals Makita BFL080F. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita BFL080F.

Similar manuals

A complete manual for the device Makita BFL080F, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita BFL080F by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita BFL080F.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita BFL080F - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita BFL080F, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita BFL080F, that we can find in the current document
3. Tips how to use the basic functions of the device Makita BFL080F - which should help us in our first steps of using Makita BFL080F
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita BFL080F
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita BFL080F in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita BFL080F?

Use the form below

If you did not solve your problem by using a manual Makita BFL080F, ask a question using the form below. If a user had a similar problem with Makita BFL080F it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)