English dropdown-ico

Manual Bunn H5E

22 pages 1.58 mb
Download

Go to site of 22

Summary
  • Bunn H5E - page 1

    BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 www .bunnomatic.com H5E H5X 10420.0000K 06/05 © 1989 BUNN-O-MATIC CORPORATION OPERA TING & SER VICE MANU AL WARNING Very Hot Water Use With Care! ! DISCONNECT FROM POWER SOURCE BEFORE REMOVAL OF ANY PANEL OR REPLACEM ...

  • Bunn H5E - page 2

    2 CONTENTS Introduction ................................................. 2 Warranty ...................................................... 2 User Notices ................................................ 3 Electrical Requirements ............................... 4 Plumbing Requirements .............................. 4 Initial Set-Up ................ ...

  • Bunn H5E - page 3

    3 12593.0000 00831.0000 10044.0000 USER NOTICES The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels. 00656.0000 10420 072500 ...

  • Bunn H5E - page 4

    4 ELECTRICAL REQUIREMENTS CAUTION - The dispenser must be disconnected from the power source until specified in Initial Set-Up. This dispenser requires 2-wire, grounded service rated 120, 208, or 240 volts ac, 20 amp, single phase. (Refer to the dispenser’s dataplate for exact voltage requirement.) Electrical Hook-Up CAUTION – Improper electric ...

  • Bunn H5E - page 5

    5 INITIAL SET -UP CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Remove the upper rear panel and place the tank heater switch in the “OFF” position and replace the panel. 2. Connect the dispenser to the power sour ce and turn-on the water supply . 3 ...

  • Bunn H5E - page 6

    6 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T ech- nical Service Department. • Inspection, testing, and repair of electrical equipment should be performed only by q ...

  • Bunn H5E - page 7

    7 TROUBLESHOOTING (cont.) Problem Probable Cause Remedy Automatic refill will not operate after drawing hot water . Water flows into the tank con- tinuously (Dispenser discon- nected from power sour ce). Water flows into the tank con- tinuously (Dispenser connected to power source). Water is cold. 1. No water 2. W ater strainer/flow control 3. Safe ...

  • Bunn H5E - page 8

    8 TROUBLESHOOTING (cont.) Problem Probable Cause Remedy Water boils continuously . Dispenser is making unusual noises. Ready indicator will not light. (when temperature is within 4 ° of its selected setting.) 1. T emperature control 2. Lime build-up 1. Solenoid valve 2. Plumbing lines 3. Water supply 1. T emperature control 2. Ready Indicator LED ...

  • Bunn H5E - page 9

    9 SERVICE This section provides procedures for testing and replacing various major components used in this dis- penser should service become necessar y . Refer to T roubleshooting for assistance in determining the cause of any problem. Component Access WARNING – Disconnect the dispenser from the power source before the removal of any panel or the ...

  • Bunn H5E - page 10

    10 SERVICE (cont.) Electronic Controls Location: The electronic control assembly is located inside the rear of the dispenser . Access will also be needed to the temperature sensor , over flow tube temperature sensor , and liquid level probe located on the tank lid and to the triac assembly located beneath the tank. General: This system controls the ...

  • Bunn H5E - page 11

    11 SERVICE (cont.) Electronic Controls (cont.) Liquid Level Control Test Procedure 1. Disconnect the dispenser from the power sour ce. 2. Check the voltage across terminals 3 & 4 of the electronic control assembly with a voltmeter . Con- nect the dispenser to the power sour ce. The indi- cation must be: a.) 100 to 120 volts ac for 100 to 120 vo ...

  • Bunn H5E - page 12

    12 SERVICE (cont.) Electronic Controls (cont.) 7. Reconnect the pink wire to terminal 5 of the elec- tronic control assembly . 8. Loosen the compression fitting, remove the probe from the tank lid, and inspect it for mineral depos- its. Replace it if necessary . Keep the exposed ends of the probe away from any metal surface of the dispenser . 9. Ch ...

  • Bunn H5E - page 13

    13 SERVICE (cont.) Electronic Controls (cont.) If the indicator was on or blinking, the temperature sen- sor is operating properly , proceed to #7. If the indicator was off, check the sensor connection on the electronic control cir cuit board and/or replace the temperature sensor and the electronic control as- sembly . NOTE - Each temperature senso ...

  • Bunn H5E - page 14

    14 SERVICE (cont.) Electronic Controls (cont.) Electronic Controls Removal and Replacement NOTE - Each electronic control assembly is calibrated to a temperature sensor probe. Both components MUST be replaced as a set. 1. Remove all wires from the electronic control as- sembly terminals. 2. Remove the two 8-32 screws holding the electronic control ...

  • Bunn H5E - page 15

    15 10420 060305 SERVICE (cont.) Electronic Controls (cont.) Adjustments The H5X dispenser holds the water temperature at the threshhold of boiling. It is not adjustable by the user . The H5E dispenser is factory calibrated for the tem- perature specified on the data plate. If adjustment is required, use the following procedure: 1. Fill the dispense ...

  • Bunn H5E - page 16

    16 SERVICE (cont.) Limit Thermostat Location: The limit thermostat is located on the tank lid. T o test the limit thermostat, access will also be needed to the terminal block located at the rear of the dispenser . If voltage was present as described, reconnect the black wire and proceed to #5. If voltage was not present as described, refer to the W ...

  • Bunn H5E - page 17

    17 SERVICE (cont.) Safety Overflow Switch Location: The safety overflow switch is located inside the rear of the dispenser inside the copper overflow cup. For testing or removal of the safety overflow switch, access may also be needed by removing the two screws attaching the electronic control assembly to its mount- ing bracket. Test Procedure: 1. ...

  • Bunn H5E - page 18

    18 SERVICE (cont.) Solenoid Valve Location: The solenoid valve is located inside the rear of the dis- penser on the right side near the bottom. T o test the solenoid valve, access will also be needed to the electronic control assembly . 7. Check the solenoid valve for coil action. Connect the dispenser to the power sour ce. Listen carefully in the ...

  • Bunn H5E - page 19

    19 SERVICE (cont.) Tank Heater Location: The tank heater is located in the tank lid. Test Procedure: 1. Disconnect the dispenser from the power sour ce. 2. Check the voltage across the terminals of the tank heater with a voltmeter . Connect the dispenser to the power sour ce. The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt model ...

  • Bunn H5E - page 20

    20 ...

  • Bunn H5E - page 21

    21 ...

  • Bunn H5E - page 22

    22 TANK HEATER SW ELECTRONIC CONTROL ASSY 230 VOLTS A C 2 WIRE SINGLE PHASE LIMIT THERMOSTAT SCHEMATIC WIRING DIAGRAM H5XA, H5EA BLU BLU 10332.0001B 09/02 © 2002 BUNN-O-MATIC CORPORATION L1 N WHI/VIO SOL H5XA Only GRN/YEL (PROBE) PNK 20 6 7 3 2 1 5 4 TAN RED RED RED BLK GRN/YEL BLK WHI/BLU RED SAFETY SW RED RED WHI/BRN BLK t ° W H I W H I G R Y G ...

Manufacturer Bunn Category Water Heater

Documents that we receive from a manufacturer of a Bunn H5E can be divided into several groups. They are, among others:
- Bunn technical drawings
- H5E manuals
- Bunn product data sheets
- information booklets
- or energy labels Bunn H5E
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bunn H5E.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bunn H5E, service manual, brief instructions and user manuals Bunn H5E. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bunn H5E.

Similar manuals

A complete manual for the device Bunn H5E, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bunn H5E by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bunn H5E.

A complete Bunn manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bunn H5E - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bunn H5E, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bunn H5E, that we can find in the current document
3. Tips how to use the basic functions of the device Bunn H5E - which should help us in our first steps of using Bunn H5E
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bunn H5E
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bunn H5E in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bunn H5E?

Use the form below

If you did not solve your problem by using a manual Bunn H5E, ask a question using the form below. If a user had a similar problem with Bunn H5E it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)