Manual Jensen CD1211

20 pages 0.71 mb
Download

Go to site of 20

Summary
  • Jensen CD1211 - page 1

    CD1211 Owner's Manual / TUNE CD1211 CD RECEIVER SCAN MONO EQ AUX IN AM/FM/CD Receiver ...

  • Jensen CD1211 - page 2

    CD1211 2 PREPAR ATION Getting Started Congratulations on your purchase of the Phase Linear CD121 1 Mobile AM/FM/CD Receiver . It’ s a good idea to read all of the instructions before beginning the installation. We recommend having your Phase Linear CD121 1 installed by a reputable installation shop. Contents Installation Instructions ............ ...

  • Jensen CD1211 - page 3

    CD1211 3 INSTALLATION INSTRUCTIONS This unit is designed for installation in cars, trucks and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are availabl e at electronics supply stores and car stereo specialty shops. Always check the kit application bef ...

  • Jensen CD1211 - page 4

    CD1211 4 9. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard, either above or below the radio, using the screw and hex nut provided. Bend the strap, a s necessary , to position it. CAUTION: ...

  • Jensen CD1211 - page 5

    CD1211 5 Remove Radio T o remove the radio after installation, remove the trim ring by lifting in the center and pulling it off from either side. Insert the removal keys straight back until they lock, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. Removal Key ...

  • Jensen CD1211 - page 6

    CD1211 6 WIRING 1. Power Antenna (dark blue wire) - Connect to power antenna or amplifier . If not use d, tape bare end of wire. 2. Accessory/Ignition (red wire) - Connect to existing radio wire or radio fuse. 3. Ground (black wire) - Connect to ground terminal or clean, unpainted part of chassis. 4. Memory/Battery (yellow wire) - Connect to batter ...

  • Jensen CD1211 - page 7

    CD1211 7 OPERATING INSTRUCTIONS Power Press the power button (1) or any o ther button on the face of the receiver to turn the unit on when the ignition switch is on. Press the power button again to turn the receiver of f. If the radio was left on when the ignition was last turned off, the receiver will turn on automatically when the ignition switch ...

  • Jensen CD1211 - page 8

    CD1211 8 Balance Press the AUDIO CONTROL button (4) four times until “BAL” appears in the display . Within five seconds, turn the AUDIO CONTROL (3) clockwise (or counter clockwise) to adjust Balance between the right and left speakers from “BAL 10R” (full right) to “BAL 10L” (fu ll left). “BAL L=R” represents an equal balance level ...

  • Jensen CD1211 - page 9

    CD1211 9 Display (D) When the unit is off, the LCD displays the time of day . When the unit is on, the LCD automatically shows the tuner or CD display , depending on which mode of operation is currently activated. Display Clock During tuner or CD operation, press D (9) to display the time of day . After five seconds, the display reverts to tuner or ...

  • Jensen CD1211 - page 10

    CD1211 10 T UNER OPER ATION AM/FM Band Selector (BAND) Press BAND (5) during radio play to switch between three FM bands and one AM band. “F1”, “F2”, “F3” or “AM” will appea r in the display to indicate the band currently selected. Tuning Automatic Tuning Press the Up T uning (14) button to tune upwa rd in frequency and the Down Tun ...

  • Jensen CD1211 - page 11

    CD1211 11 Repeat for the remaining five presets on the current band and for all presets on the other three bands. Automatically Store / Pr eset Scan (AS/PS) Automatically Store Select six strong stations and store them in the current band using the Automa tic S tore feature. T o enable this feature, press and hold AS/PS (17) for more than two secon ...

  • Jensen CD1211 - page 12

    CD1211 12 CD PLAY ER OPERATION Insert CD With the label surface facing up, gently insert the disc into the CD slot (21) until the soft- loading mechanism engages and pulls the disc in. Disc play begins, “CDP PLA Y” will appear in the display , and the CD icon will become animated. The center of the disc icon (7) illuminates and becomes animated ...

  • Jensen CD1211 - page 13

    CD1211 13 Disc Repeat (RPT) Press RPT (25) during disc play to cont inuously repeat the selected track. “S--RPT” will appear in the display . Press RPT again to stop repeating. “S--RPT” will disappear from the display , and regular play will resume. The repeat function will also be canceled when activating the scan or shuffle functions. Dis ...

  • Jensen CD1211 - page 14

    CD1211 14 REMOTE CONTROL The remote control will allow you to control the basic functions of the CD121 1. The remote control sensor is located on the left side of the front panel to the rig ht of the MONO button (18). S VOL VOL D U BND SCN MOD LOC AMS PEQ MO MUT DISP 12 3 4 5 6 PA U SCN RPT SHUF DN UP LOUD TR. DN TR. UP AMS = AS/PS PEQ = EQ MOD = M ...

  • Jensen CD1211 - page 15

    CD1211 15 CARE AND MAINTENANCE CD Player The following guidelines will help you extend the life of your CD player: 1. When cleaning the vehicle interior , do not get water or cleaning fluids on the unit. 2. The CD player will not operate properly in extreme hot/cold or under damp conditions. In case of such conditions, wait until the vehicle interi ...

  • Jensen CD1211 - page 16

    CD1211 16 T R OUBLESHOOTING Problem Cause Corrective Action Does not operate (display does not light) No power to yellow wire; no power to red wire Check c onnection with test light; chec k vehicle fuse with test light. Inline fuse blown Replace fuse. No power to unit Inline fuse blown Check/replace fuse. Not all speakers operate Incorrect splices ...

  • Jensen CD1211 - page 17

    CD1211 17 SPECIFICATIONS CEA Power Ratings Power output: 13 watts RMS X 4 channels into 4-ohms @ < 1% THD+N Signal to noise ratio: 70dBA below refere nce. (Reference: 1 watt, 4-ohms) Frequency response: 20Hz to 20kHz (-3d B), Auxiliary input used as source reference Reference supply voltage: 14.4VDC CD Player Signal-to-noise ratio: >90dBA Fre ...

  • Jensen CD1211 - page 18

    Limited Warranty DO NOT RETURN THIS PRODUCT TO THE STORE CD or Multimedia Radios/Headunits Audiovox Electronics Corporation (“the Company”) is committed to quality and customer service, and are pleased to offer you this Warranty. Please read it thoroughly and contact the Company at 1-800- 323-4815 with any questions. Who is covered? The Company ...

  • Jensen CD1211 - page 19

    ...

  • Jensen CD1211 - page 20

    Audiovox Electronics Corporation 150 Marcus Boulevard Hauppauge, NY 1 1788 1-800-323-4815 www .audiovox.com ©200 7 Audiovox v . 0 83107 ...

Manufacturer Jensen Category Car Stereo System

Documents that we receive from a manufacturer of a Jensen CD1211 can be divided into several groups. They are, among others:
- Jensen technical drawings
- CD1211 manuals
- Jensen product data sheets
- information booklets
- or energy labels Jensen CD1211
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jensen CD1211.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jensen CD1211, service manual, brief instructions and user manuals Jensen CD1211. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jensen CD1211.

Similar manuals

A complete manual for the device Jensen CD1211, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jensen CD1211 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jensen CD1211.

A complete Jensen manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jensen CD1211 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jensen CD1211, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jensen CD1211, that we can find in the current document
3. Tips how to use the basic functions of the device Jensen CD1211 - which should help us in our first steps of using Jensen CD1211
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jensen CD1211
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jensen CD1211 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jensen CD1211?

Use the form below

If you did not solve your problem by using a manual Jensen CD1211, ask a question using the form below. If a user had a similar problem with Jensen CD1211 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)