English dropdown-ico

Manual Craftsman 917.271641

60 pages 2 mb
Download

Go to site of 60

Summary
  • Craftsman 917.271641 - page 1

    Owner's Manual ICRnFT MRWI 16.5 HP ELECTRIC START 42" MOWER AUTOMATIC LAWN TRACTOR Model No 917.271641 • Safety • Assembly • Operation • Maintenance • Repair Parts This product has a low emission engine which operates differently from previously built engines. Before you start the en- gine, read and understand this Owner's ...

  • Craftsman 917.271641 - page 2

    Warranty ............................................... 2 Safety Rules ......................................... 3 Product Specifications .......................... 6 Assembly .............................................. 8 Operation ............................ : ............... 11 Maintenance ....................................... 18 Maintenan ...

  • Craftsman 917.271641 - page 3

    IMPORTANT: This cutting machine is capable of amputating hands and feet end throwing objects. Failure to observe the following safety instructions could result in serious injury or death. I. GENERAL OPERATION Read, understand, and follow all instructions in the manual and on the machine before starting. • Only allow responsible adults, who are fa ...

  • Craftsman 917.271641 - page 4

    IlL CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and under the watchful care of another responsible adult. • Be alert and tur ...

  • Craftsman 917.271641 - page 5

    ,, Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. • If machine stops while going uphill, disengage blades, shift into reverse and back down slowly. • Do not turn on ...

  • Craftsman 917.271641 - page 6

    PRODUCTSPECIFICA_ONS G_,SOLINE CAPACITY ANDTYPE: OILTYPE _,PI-SFoSj): 1.25 GALLONS UNLEADED REGULAR SAE 30 (ABOVE 32°F SAE 5W-30 (BELOW 32"F) OIL CAPACITY: 3.0 PINTS SPARK PLUG: CHAMPION RC12YC GAP: .030") GROUND SPEED FORWARD:5.2 (MPH): REVERSE: 2.7 TIRE PRESSURE: FRONT: 14 PSI REAR: 12 PSI CHARGING 3 AMPS BATTERY SYSTEM: 5 AMPS HEADLIG ...

  • Craftsman 917.271641 - page 7

    Steering Wheel Insert .C) ](1) Hex Bolt 3/8-16 x 1 Steerin!_ Boot Steering Wheel (1) Lock washer 3/8 (1) Large Flat Washer (1) Hex Bolt 5/16-18 x 1-1/4 (1) Locknut 5/16-18 _ Steering Wheel Adapter Steering Extension Shaft Seat (_Washer _17/32 x 1-3/16 x 12 Gauge 1) Knob Slope Sheet Keys Video Cassette 7 ...

  • Craftsman 917.271641 - page 8

    Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin. TOOLS ...

  • Craftsman 917.271641 - page 9

    Label Batter Door INSTALL SEAT Adjust seat before tightening adjustment knob. 1, Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. 2, Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard. 3. Place seat on seat pan so head of shoulder ...

  • Craftsman 917.271641 - page 10

    INSTALL MULCHER PLATE (If previously removed) 1. Raise and hold deflector shield in upright position. 2. Place front of mulcher plate over front of mower deck opening and slide into place, as shown. 3. Hook front latch into hole on front of mower deck. 4. Hook rear latch into hole on back of mower deck. Mulcher Deflector f/ Plate Shield Latch /% _ ...

  • Craftsman 917.271641 - page 11

    These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATrE BY CAUTION OR REVERSE FORWARD FAST SLOW WARNING ENGINE ON ENGINE OFF OIL PRESSURE FUEL CHOKE A LIGHTS ON OVER TEMP lr LIGHT ! MOWER HEIGHT PARKING BRAKE UNLOCKED MOWER LIFT LOCKED r_"l R N H L ATTACHMENT REVERSE NEUTRA ...

  • Craftsman 917.271641 - page 12

    KNOWYOURTRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Attachment Clutch Ammeter Throttle/Choke Control Ignition Switch Light Switch Lift Plunger Att ...

  • Craftsman 917.271641 - page 13

    The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOWTO USEYOURTRACTOR TO SET PARKIN ...

  • Craftsman 917.271641 - page 14

    • The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth. • For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired ...

  • Craftsman 917.271641 - page 15

    BEFORE STARTINGTHE ENGINE CHECK ENGINE OIL LEVEL Th.e engine in your tractor has been shipped, from the factory, already filred with summer weight oil. 1. Check engine oil with tractor on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If nec ...

  • Craftsman 917.271641 - page 16

    AUTOMATIC TRANSMISSION WARM UP Before driving the unit in cold weather, the transmission should be warmed up as follows: 1, Be sure the tractor is on level ground. 2, Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position. 3, Allow one minute for transmission to warm up. Thi ...

  • Craftsman 917.271641 - page 17

    MOWINGTIPS • Mower should be propedy leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tract ...

  • Craftsman 917.271641 - page 18

    MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check Brake Operation I1_ I1_ Check Tire pressure fl_ Check OperatOr Presence and JnledOCk System. I_ I Check for Lcose Fasteners if 11_7 If Sharpen/Replace Mower BLades I_+ LubriCation Chat1 I_ I1_ CheCk Battery Lev_ Clear= Batte_ and Terminals _ IJ_ Check Transaxle Cooling _#/ A_s ...

  • Craftsman 917.271641 - page 19

    TRACTOR Always observe safety rules when • performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJUST BRAKE" in the Sewice and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires ...

  • Craftsman 917.271641 - page 20

    • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or chocking level of erectrolyte is not necessary. TO CLEAN BATTERY AND TERMINA ...

  • Craftsman 917.271641 - page 21

    Oil Drain Valve "-Closed _Dram Tube and Cap_ CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. ENGINE COOLING FINS Remove any dust, dirt or oil from engine cooling fins to prevent engine damage from o ...

  • Craftsman 917.271641 - page 22

    " Fuel ) / CLEANING Clean en_line, battery, seat, finish, etc. i of fore=gn matter. all Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automo- tive type wax. We do not recommend using a garden hose to clean your tractor unless the electrical system, muffler, air filter and carburetor are cov ...

  • Craftsman 917.271641 - page 23

    TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground ordriveway. Make sure tlr_s are propedy inflated (See "PROD- UCT SPECIF)CATtONS" section of this manual)• If tires are over or underinflated, you willnot properly adjust your mower. • SIDE-TO-SIDE ADJUSTMENT • Raise mower to its highest position. At the ...

  • Craftsman 917.271641 - page 24

    TO REPLACE MOWER BLADE DRIVE BELT The mower blade drive belt may be replaced without tools• Park the tractor on level surface. Engage parking brake. BELT REMOVAL - 1. Remove mower from tractor (See "TO REMOVE MOWER" in this section of this manual). 2. Work belt off both mandrel pulleys and idler pulleys. 3. Pull belt away from mower. BE ...

  • Craftsman 917.271641 - page 25

    TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT The motion control lever has been preset at the factory and adjustment should not be necessary. 1. Loosen adjustment bolt in front of the right rear wheel, and lightly tighten. 2. Start engine and move motion control fever until tractor does not move forward or backward. 3. Hold motion control lever ...

  • Craftsman 917.271641 - page 26

    TO ATTACH JUMPER CABLES - 1. Connect each end of the RED cable to {he POSITIVE (+) terminal of each battery, taking care not to short against chassis• 2. Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery. 3. Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery. TO ...

  • Craftsman 917.271641 - page 27

    ENGINE Maintenance, repair, or replacement of the emission control devices and sys- tems, which are being done at the customers expense, may be performed by any non-road engine repair establish- ment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet. TO ADJUST THROTTLE CONTROL CABLE The thr ...

  • Craftsman 917.271641 - page 28

    ACCELERATION TEST - 4. Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle mixture valve out (counterclockwise) 1/8 turn. Repeat test and continue to adjust, if neces- sary, until engine accelerates smoothly. High speed stop is factory adjusted. Do not adjust - damage may result. IMPORTANT: Never tamper wi ...

  • Craftsman 917.271641 - page 29

    Immediately prepare your tractor for storage at the end of the s, eason or if the tractor will not be used for 30 days or more, • I,CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark• Allow the engine to cool before storing in any enclosure. TRACTOR Remove mower from tractor ...

  • Craftsman 917.271641 - page 30

    TROUBLESHOOTING CHART PROBLEM Willnotstart Hard to start Enginewill not turn over Engine clicks but will not start CAUSE 1, Out of fuel, 2. Engine not "CHOKED" properly, 3. Engine flooded, 4. Bad spark plug. 5. Dirty air filter. 6. Dirty fuel filter. 7. Water in fuel. 8. Loose or damaged wiring. 9. Carburetor out of adjustment. 10. Engine ...

  • Craftsman 917.271641 - page 31

    TROUBLESHOOTING CHART PROBLEM LOSS of power continued) Excessive vibration Enginecontinues to run when operator leaves seat with. attachment clutch engaged Poorcut-uneven CAUSE CORRECTION 3. Build-up of gross, leaves and trash under mower. 4. Dirty air filter. 5. Low oil level/dirty oil. 6. Faulty spark plug. 7. Dirty fuel filter. 8. Stale or dirty ...

  • Craftsman 917.271641 - page 32

    TROUBLESHOOTING CHART PROBLEM CORRECTION Poor grass discharge Headlight(s) not working (if so equipped) Battery will not charge Loss of drive Engine "backfires" when turning engine "OFF" CAUSE 1. Engine speed too slow. 2. Travel speed too fast. 3. Wet grass. 4. Mower deck not level. 5. Low/uneven tire air pressure. 6. Worn, bent ...

  • Craftsman 917.271641 - page 33

    SCHEMATIC TRACTOR -- MODEL NUMBER 917.271641 BAKERY AMMETER __(OPTIONAL) GL_ At( IGNITION SWITCH IGNITION SWITCH RED I I _o FUSE , 1_ _Ii_ -__ _ _ S_K , i STARTER "_'_ ', 0 ', 04----_ I '- - : --' _ I I SOLENO,D CWTOH,ORA,E 'PEOALfPf I [ SEAT SWITCH ...... (NOT OCCUPIED nt_CK i t _CK I r , o B_K _ ..... J ....... ...

  • Craftsman 917.271641 - page 34

    TRACTOR -- MODEL NUMBER 917,271641 ELECTRICAL 22 J I i q i i J_i p_i jjs i i i 29 34 ...

  • Craftsman 917.271641 - page 35

    ELECTRICAL TRACTOR -- MODEL NUMBER 917.271641 KEY PART NO. NO. DESCRIPTION 1 144925 Battery 12 VOLT 25 AMP 2 74760412 Bolt Hex Hd 1/4-20unc x 3/4 8 156417 Case Battery 16 153664 Switch, Interlock Push-in 21 166182 Harness Asm Ught W/4152J 22 4152J Bulb Light #1156 24 4799J Cable Battery 6 Ga "i 1" red 25 146147 Cable Battery 6 Ga w/16 wir ...

  • Craftsman 917.271641 - page 36

    TRACTOR -- MODEL NUMBER 917.271641 CHASSIS AND ENCLOSURES 12 207 54 52 55 57 36 ...

  • Craftsman 917.271641 - page 37

    TRACTOR - - MODEL NUMBER 917.271641 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174619 Chassis 2 176554 Drawbar 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper HOCd/Dash 9 168337X019 Dast_ 10 STD533710 Bolt, Carriage 3/8-16 x 3/4 1 t 155927 Panel, Dash, LH. 12 145660 Clip TInnerman Gdlle P/L 13 172107X010 Panel, Dash, R,H. 14 1749(_o05 Scre ...

  • Craftsman 917.271641 - page 38

    I HAL; I UI'I - - MUUI-L NUNI_t-I'I _11 f.Z/1t)41 GROUND DRIVE i i 212 70 116 53 3O 38 ...

  • Craftsman 917.271641 - page 39

    TRACTOR -- MODEL NUMBER 917.271641 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 ...... Transmission (See Breakdown) 66 154778 Keeper, Bell Engine Hydro Hydro Gear Model 322-0510 70 134683 Guide, Belt, Mower Drive RH 8 165866 Rod, Shift 71 169183 Strap, Torque, Lh 10 STD561210 Pin, Cotter 1/8 x 1 73 169182. Strap, Torque, ...

  • Craftsman 917.271641 - page 40

    TRACTOR - - MODEL NUMBER 917.271641 STEERING ASSEMBLY j-_ L • - __ :LI) , , | , , "'-LLL_-- L'--:: "" 4O ...

  • Craftsman 917.271641 - page 41

    TRACTOR -- MODEL NUMBER 917.271641 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 139768 SteedngWheel 2 154427 Axle Assembly STM P Dropped STL 3 169840 Spindle Assembly, L.H. 4 169839 Spindle Assembly, R.H. 5 6266H Beadng, Race, Thrust, Hardened 6 121748X Washer 25/32 x 1-5/8 x 16 Gauge 7 19272016 Washer 27/32 x 1-1/4 x 16 Gauge 8 120000_9 Ring, ...

  • Craftsman 917.271641 - page 42

    ENGINE TRACTOR - - MODEL NUMBER 917,271641 3 72 81 62 J 13 4 i 33 4O 29 OPTIONAL EQUIPMENT Spark Arrester 23 14 78 42 ...

  • Craftsman 917.271641 - page 43

    ENGINE TRACTOR -- MODEL NUMBER 917.271641 KEY PART NO. NO. DESCRIPTION 1 170545 Control Throt/Ch 2 17720410 Screw Hex Thd Cut 1/4-20x5/8 T 3 ........ Engine (See Breakdown) Bdggs Model 310707-0137-E1 4 137352 Muffler Exhaust B&S Lt 13 165291 Gasket 1 313 Id Tin Plated 14 148456 Tube Drain oil easy 16 STD551237 Washer Lock Ext Tooth 3/8 23 16983 ...

  • Craftsman 917.271641 - page 44

    I HA(.; I UH - - MUUI:;L NU MI_I- H 917.271541 SEAT ASSEMBLY KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 140122 Seat 3350 BIk/bik Craftsman 13 121248x 2 140551 Bracket Pnt Pivot Seat (blk) 14 72050412 3 71110616 BOlt Fin Hex 3/6-16unc X 1 15 134300 4 19131610 Washer 13/32 X 3/4 X 10 Ga 16 121250X 5 145006 Clip Push In Hingecl 17 123 ...

  • Craftsman 917.271641 - page 45

    DECALS TRACTOR -- MODEL NUMBER 917.271641 13 12 10 2O KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 156811 2 171761 3 171696 4 171697 6 133644 7 177253 8 172331 9 163204 10 156439 12 146O46 13 177269 Decal, Oper. Instr. 14 160_96 Decal, V-Belt SchernaUc Decal, Replacement 15 176677 Decai,Englne Decal, Hood, R.H. 20 149516 Decal Battew ...

  • Craftsman 917.271641 - page 46

    I i-I_t_ I un " - iVI_K.SI_f- INtt.XlVl D_.rl _ I I ,_1 I fDq} I LIFT ASSEMBLY 7 5 / / / 13 2 3 6 19 13 32 13 31 _ 32 "/ 13 19 2O 20 15 46 ...

  • Craftsman 917.271641 - page 47

    TRACTOR -- MODEL NUMBER 917.271641 LIFT ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 159460 Washer Asm Inner Spring W/Plunger 2 159471 Shaft Asm. Lift 3 105767X Pin Groove 4 1200(]002 E Ring #5133-62 5 19211621 Washer 21/32 x 1 x21 Ga. 6 120183X Beadng Nyk)ng 7 125631X Grip Harldle Fluted 8 122365X Button Plunger Read 11 139865 Link Asm Lilt L.H. 12 139 ...

  • Craftsman 917.271641 - page 48

    TRACTOR -- MODEL NUMBER 917.271641 MOWER DECK 153 1_4 44 i_" _ ! _-145 56_ ¢1 ! 59 148 .- i 32, ; i 30 i _'_ ' 102_ 34 "i_21 I i i 147 142 - i 106_'_ 102 103 105 , Sr I 16 t, o , _21 ' _.18 21 22 23 24 < s 28 _. 27 48 ...

  • Craftsman 917.271641 - page 49

    TRACTOR -- MODEL NUMBER 917.271641 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 165892 Mower Deck Assembly, 42" 53 131845 2 STD533107 Bolt 54 133943 3 138017 Bracket Assembly,Sway Bar, Front 55 155046 4 165460 Bracket Sway Bar 35/42" Deck 56 165723 5 STD624C08 Retainer Spdeg 59 141043 6 130832 Arm, Suspension, Rear 67 149846 ...

  • Craftsman 917.271641 - page 50

    TRACTOR - - MODEL NUMBER 917.271641 HYDRO TRANSAXLE -- MODEL NUMBER 322-0510 14_. 5O ...

  • Craftsman 917.271641 - page 51

    TRACTOR -- MODEL NUMBER 917.271641 HYDRO TRANSAXLE - - MODEL NUMBER 322o0510 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 170351 Main Housing, Assembly 60 142883 Brake Puck 2 170352 Side Housing, Assembly 61 142882 Puck Plate 3 170353 Center Section, Assembly 62 170409 Brake Actuating Pin 4 170354 Swashplate, TnJnion Macblned 63 1704 ...

  • Craftsman 917.271641 - page 52

    TRACTOR -- MODEL NUMBER 917.271641 BRIGGS & STRATFON ENGINE-MODEL NUMBER 310707,'P(PE NUMBER 0137-E1 "k REQUIRES SPECIALTOOLS 53_ TO NSTALL. SEE REPAIR _,_ INSTRUCT ON MANUAL. 11 552 691 e_ 52 ...

  • Craftsman 917.271641 - page 53

    TRACTOR -- MODEL NUMBER 917.271641 BRIGGS & STRATTON ENGINE-MODEL NUMBER 310707,TYPE NUMBER 0137-E1 51 I '_'+<_+ _l 53 ...

  • Craftsman 917.271641 - page 54

    I I_#.lv I ken " - IVIUI./P-.6 |MUIVII_CM _ I /._/ 104 I BRIGGS & STRAT[ON ENGINE-MODEL NUMBER 310707,TYPE NUMBER 0137-E1 801 L 1036 LABEL*EMISSIONS 462 ,_ 579 287 _ 524_ 7sQ 54 ...

  • Craftsman 917.271641 - page 55

    TRACTOR - - MODEL NUMBER 917.271641 BRIGGS & STRATTON ENGINE-MODEL NUMBER 310707, TYPE NUMBER 0137-E1 977 CARBURETOR GASKET SET 15` I 1095 VALVE GASKET SET 51 _ 868 ,_ 102," NIKKI 131AI _111.;._ _l I 130AO _lr;;;',_ _Ul 987A 133AJ 10_41 / 217_ _ .... J 127A0 _ 97...O.e.I _,- /_ _i_, 105A_ 369 1127A|_. 276A_ 947A _ 121 CARBURETOR OVERH ...

  • Craftsman 917.271641 - page 56

    I tlA_., tuft - - MULJ_t. NUMt_H 917,271_41 BRIGGS & STRATTON ENGINE-MODEL NUMBER 310707,TYPE NUMBER 0137-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 690156 Cylinder Assembly 105 231855 _ Valve-Float Needle 2 399265 Kd-Sushing/Seal 105A 694922 O Valve-Float Needle 3 391086 • Seal-Oil (Magneto Side) 106 690577 Seat-Inlet 4 4 ...

  • Craftsman 917.271641 - page 57

    TRACTOR - - MODEL NUMBER 917.271641 BRIGGS & STRATTON ENGINE-MODEL NUMBER 310707,TYPE NUMBER 0137-E1 KEY PART KEY PART NO. NO, DESCRIPTION NO. NO. DESCRIPTION 287 691002 Screw (Dipstick Tube) 789 692037 Harness-Wiring 304 690844 Housina-Blower 789A 695050 Harness-Wiring 305 890960 Screw _'BIowe_ Hc_sing) 797 693167 Nut (Brush Retainer) 306 ...

  • Craftsman 917.271641 - page 58

    58 ...

  • Craftsman 917.271641 - page 59

    SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ol _o SIGHTING ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL I p. Operate your Tractor up and down the face of slopes (not I I greater than 15°), never across the face. Make turns gradu- I ally to prevent tipping or loss of control. Exercise extreme I I ...

  • Craftsman 917.271641 - page 60

    Get it fixed, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOM E sM Anytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts 8= Repa ...

Manufacturer Craftsman Category Lawn Mower

Documents that we receive from a manufacturer of a Craftsman 917.271641 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 917.271641 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 917.271641
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 917.271641.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 917.271641, service manual, brief instructions and user manuals Craftsman 917.271641. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 917.271641.

Similar manuals

A complete manual for the device Craftsman 917.271641, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 917.271641 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 917.271641.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 917.271641 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 917.271641, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 917.271641, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 917.271641 - which should help us in our first steps of using Craftsman 917.271641
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 917.271641
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 917.271641 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 917.271641?

Use the form below

If you did not solve your problem by using a manual Craftsman 917.271641, ask a question using the form below. If a user had a similar problem with Craftsman 917.271641 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)