Manual Troy-Bilt 10030

29 pages 3.89 mb
Download

Go to site of 29

Summary
  • Troy-Bilt 10030 - page 1

    Snow Thrower Mode l 1003 0 PRINT ED IN U .S. A. Oper ator ’ s Ma n ual FORM NO . 769-00376.fm (6/2002 ) IM PO RT AN T : Re ad saf ety rules and i nstructions care fully bef ore oper ating equ ipmen t. TRO Y-BIL T LLC. P .O . BO X 36 1131 CLE VELAND , OHIO 44136- 0019 Warning: T his u ni t i s eq ui pp ed w it h a n in ter na l c omb us tion en gi ...

  • Troy-Bilt 10030 - page 2

    2 TABL E OF CO NTENT S Content Page Import ant Sa fe Ope ratio n Pract ices ..... .. ..... ..... .... ... ..... .... ..... ..... .. ..... ..... .... ..... .. ..... ..... ..... .. 3 Assem bling Your Snow Throwe r ..... ... .... ..... ..... .... ... ..... .... ..... ..... .. ..... ..... .... ..... .. ..... ..... ..... .. 5 Know Yo ur Snow Thrower ... ...

  • Troy-Bilt 10030 - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES DANGER: This machi ne was built to be operated according to the rules for safe operat ion in this manual. As with any type of powe r eq uipment, carelessness or error on the part of the operator can result in serious injury. This machine is capabl e of amputating han ds and feet and throwin g objects. ...

  • Troy-Bilt 10030 - page 4

    4 5. Never ru n an engi ne indoo rs or in a poorly ven tila ted area. Engine exhaust contains ca rbon m onoxide , an odorl ess and d eadly ga s. 6. Do not ope rate mach ine whi l e under the i nflue nce of alcoh ol or drugs. 7. Muffle r and en gine bec ome hot a nd can ca use a bur n. Do not t ouch. 8. Exerci se extrem e caution wh en ope rating on ...

  • Troy-Bilt 10030 - page 5

    5 SECTION 2: ASSEMBLING YOUR SNOW THROWE R Un packing • Remove s taples from the top, sides, a nd ends of the shipp ing crate. • Set panels aside to avoid tire punctures or persona l inj ur y. • Remove and di scard plastic bag that cov ers unit. • Roll the unit out of the crate. • Check the crate for loose part s before discarding. Loose ...

  • Troy-Bilt 10030 - page 6

    6 Fi gur e 3 • Unwrap the head light wire which is attached to the headlig ht, beneath the handl e panel. Wind the headlig ht wi re arou nd the lower right handle until excess sl ack is removed. See Fi gure 4. • Plug the wire from the head light into the alternator lead comi ng from the right side of the eng ine underneat h the fuel tank. Fi gu ...

  • Troy-Bilt 10030 - page 7

    7 Fi gur e 5 Tire Pre ssure (Pn eumatic Tire s) The tires are overinflated for shipping pu rposes. • Check tire pressure. Maintain pressure between 10 and 14 ps i. NOTE: If the tire p r e ssure is not equal in all tires, th e unit may pull to one side or th e other. SECTION 3: KNOWING YOUR SNOW THROWE R • Compare the figure below and descriptio ...

  • Troy-Bilt 10030 - page 8

    8 Tractio n Control / Auge r Co ntrol Lo ck The traction control is locate d on the right handle. Squeeze the traction control to engage the wheel d rive. Re l eas e to st op. This same lever also locks t h e auger control so you can operate the chute crank without interrupting the snow throwing process. If the auge r control i s enga ged simultane ...

  • Troy-Bilt 10030 - page 9

    9 SECTION 4: OPERATING Y OUR SNOW THROW ER Befo re Start in g Read and unders tand all instructions and warnin gs on the machine and in t his manual bef or e o perating. Gas & O il Fill-Up • Service the engine wi th gasoline and oil as instructed in the engine manual shippe d with the snow thrower. • A plastic cap i s provided inside the fu ...

  • Troy-Bilt 10030 - page 10

    10 Recoil St arter: With engin e running, pull star ter rope with a r apid, continuou s f u ll arm strok e three or f our times. Pulling the s tar ter rope will produce a loud clattering sound , whi ch is nor ma l. • Move throttle cont rol to “ st op ” or “ off ” po siti o n. • Remove igni ti o n key. Do not turn key. Disconnec t the sp ...

  • Troy-Bilt 10030 - page 11

    11 SECTION 5: MAKING ADJUSTMENTS Shift R od Fi gur e 8 • Remove th e hairpin cl i p and flat washer from the shift handle under the handle panel. See Figure 8. • Place shift lever in sixth (6) position or fastest forward speed. • Push shift arm assembl y down as far as it wi ll go. • Rotate the ferrule up or down on the shi ft r o d as nece ...

  • Troy-Bilt 10030 - page 12

    12 Skid Sh oe The space between the shave plate and the ground can be adjusted by raising o r lowering the skid shoes. For close snow remov al, as when using on a smooth concrete or aspha lt dri veway, place the skid shoes in the low position. Use the middle or high po siti o n when the area to be cleared is uneven. When op erating on gravel, alway ...

  • Troy-Bilt 10030 - page 13

    13 SECTION 6: MAINTAINING YOUR SNOW THROWER Gener al Recommendat ions • Always observ e safety rules when performing any main tenance. • The warranty on this snow thrower does not cover items that have been subjecte d to operator abuse or negligen ce. To receive full value from the warranty, operato r m ust maintain the snow thrower as instruct ...

  • Troy-Bilt 10030 - page 14

    14 Figu re 15 Tractio n Control / Auge r Co ntrol Lo ck The cams on th e ends of the control rods which interlock the traction drive and aug er d rive clutches must be lubricated at least once a season or every 2 5 hours of operation using a m ulti-purpose au tomotive grease. The cams can be ac cessed beneat h the han dle panel. See Figure 16. Figu ...

  • Troy-Bilt 10030 - page 15

    15 SECTION 7: SERVICING YOU R SNOW TH ROWE R Auge rs The augers are secured to the spiral shaft with two shear bolts and hex lock nut s. If you hit a foreign object or ice jam, the snow thrower is designed so that the bolts may shear. Refer to Figure 13. • If the augers do not turn, chec k if the bolts have shea red. Two replacement shear bolts a ...

  • Troy-Bilt 10030 - page 16

    16 Figu re 19 • Lift the rear auger belt from the aug er pulley, and slip the belt be tween the support bracket a nd the auger pulle y. Repeat for the front auger belt. See Figure 20. • Replace both a uger drive belts by following instructions in reverse order. • If you placed plastic f ilm under the gas cap earli er, remove it now. Figu re 2 ...

  • Troy-Bilt 10030 - page 17

    17 Figu re 23 • Lift the friction wheel assem bly out between the axle sha ft and the drive shaft assem blies. • Remove th e four screws from the friction wheel assem bly. Remove the friction wheel rubb er from betwee n the friction wheel plates. See Fi gure 24. • Reassem ble the new friction wheel rubber to the friction wheel p lates and hub ...

  • Troy-Bilt 10030 - page 18

    18 SECTION 9: TROUBLESHOOTING NOTE: F or repairs beyond m inor adjustments listed a bove, contact the local dealer. Prob lem Caus e Reme dy Engin e fails to sta rt. 1. Fuel tank e m p ty, or st ale fuel . 2. B l oc k ed f u el li ne . 3. Choke not in ON posit ion 4. F a u lty s par k pl ug . 5. Safety key not in i g nition s w it ch on engi ne. 6. ...

  • Troy-Bilt 10030 - page 19

    19 Sa fety & Decorati ve Label s 10 H P ® D06572 777D06572 777I22047 PLACE ABOVE INGNITION CUT OUT ST OP S T O P 10030 D06573 777D06563 777D06573 D00056 777S32065 DANGER NEVER PUT HAND IN CHUTE. CONTACT WITH ROTATING PARTS CAN AMPUTATE FINGERS AND HANDS. USE CLEAN-OUT TOOL TO UNCLOG DISCHARGE CHUTE. DO NOT UNCLOG DISCHARGE CHUTE WHILE ENGINE I ...

  • Troy-Bilt 10030 - page 20

    20 SECTION 10: PARTS LIST FOR MODEL 10030 29 9 25 19 30 24 5 17 14 13 18 1 13 18 27 6 22 16 10 23 23 10 7 7 26 21 28 11 8 28 21 13 22 15 24 24 22 6 32 31 38 44 37 39 36 34 35 33 43 45 41 22 13 42 40 45 ...

  • Troy-Bilt 10030 - page 21

    21 Model 10030 Ref. No. P a r t No. P art Descr iption 1. 05931A Beari ng Housi ng 2. 684-0 065 Impel ler As sembly 3. 705-5 226 Chute Re inforcement 4. 710-0 451 Carri age Bolt 5. 710-0 459A Hex Bol t 3/8-24 x 1.5 ” 6. 710-0 604A TT Scre w 5/16-1 8 x 0.625 ” 7. 710-0 703 Carri age Screw 1/ 4-20 x 0 .75 ” 8. 710-0 890A Shear Bo lt 9. 712-0 11 ...

  • Troy-Bilt 10030 - page 22

    22 Model 10030 1 5 6 8 9 12 13 14 16 18 19 20 22 25 30 8 8 35 45 13 8 8 33 31 36 20 31 43 31 36 22 23 31 33 37 18 11 38 32 17 3 10 32 38 44 37 2 25 8 12 8 30 16 8 41 21 29 42 4 24 7 27 15 26 50 10 10 51 10 35 45 13 28 22 40 39 41 50 45 35 53 52 47 49 54 57 56 58 59 59 62 60 61 6 55 63 64 65 ...

  • Troy-Bilt 10030 - page 23

    23 Model 10030 Ref. No. P ar t No. Part Description 1. 618-0 043 Dogg Asse mbly RH 2. 618-0 044 Dogg Assembly LH 3. 618-0 575 Driv e Shaft 4. 656-0 012A Fric tion Wheel Disc Assembly 5. 684-0 014B Shif t Rod Asse m bly 6. 684-0 042C Friction Whe el Assembly (i ncludes ite m s 58 to 62) 7. 684-0 131A Support Bracke t 8. 71 0-0599 TT screw 1/4-2 0 x ...

  • Troy-Bilt 10030 - page 24

    24 Model 10030 A A 1 2 3 4 5 6 7 8 44 9 10 11 12 13 14 15 16 17 18 19 20 8 20 14 14 21 22 14 24 23 25 26 27 28 29 30 31 32 33 8 8 24 34 35 36 37 38 39 40 41 42 43 45 46 47 40 L1 G D L2 E F C B A B C L1 Harne ss As sembly Connector Plugs to: A Altern ator lead f rom engine B, C, L1 , L2 Swit ch and Li ght 1 and 2 D, E Hea ted Grips o f handl es F in ...

  • Troy-Bilt 10030 - page 25

    25 Model 10030 Ref. No. P a rt No. P a rt Description 1. 684 -0008A Shift Ar m Assembly 2. 684 - 005 3B Chut e Crank assem bly 3. 705 - 526 6 Chut Cran k Bracke t 4. 710 -0449 Carri age Screw 5 /16-18 x 2. 25 ” 5. 710 - 045 8 Carri age Bolt 5/ 16-18 x 1.75 ” 6. 710 -0643 Hex Sc rew 5/16-18 x 1.0 ” 7. 710 -0788 TT Screw 1/ 4-20 x 1.0 ” 8. 71 ...

  • Troy-Bilt 10030 - page 26

    26 Model 10030 1 2 3 4 5 6 7 8 9 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 28 29 30 10 23 23 4 31 32 34 33 Suppli ed on engine 17 31 ...

  • Troy-Bilt 10030 - page 27

    27 Model 10030 Ref. No. P art No. Descript ion 1. 058 96A Idler Br ack et: Driv e Clut ch 2. 710 -1245B Hex Bol t 5/16-24 x .875 ” 3. 710 -0230 Hex Scr ew 1/4- 28 x .50 ” 4. 710 -0627 Hex Scr ew 5/16- 24 x .750 ” 5. 710 -0654A TT Screw 3/ 8-16 x 1.0 ” 6. 710 -0696 Hex Scr ew 3/8- 24 x .875 ” 7. 710 -1652 TT Screw 1/4-2 0 x .625 ” 8. 710 ...

  • Troy-Bilt 10030 - page 28

    28 Model 10030 Ref. No. P art No. Descri ption 1. 710- 04071 Carr iage Bolt 5/16-18 x 1.0 ” 2. 710- 0262 Carr iage Bolt 5/16-18 x 1. 5 ” 3. 710- 0805 Hex Bol t 5/16 -18 x 1.5 ” 4. 710- 0896 Hex AB Scr ew 1/4- 14 x .625 ” 5. 710- 3015 Hex Scr ew 1/4- 20 x .75 ” 6. 712- 0429 Hex Loc k Nut 7. 712- 3027 Hex Fl ange Lock Nut 8. 731- 1320 Upper ...

  • Troy-Bilt 10030 - page 29

    MANUF A CTURER ’ S LIMITED W ARRANTY FOR: The l imited warr anty s et forth below is gi ven by Troy-Bil t LLC with respect t o new me rchandise p urchased and used i n the Unit ed Stat es, its p ossessi ons and t errito ries. Troy- Bilt LLC wa rrant s this pr oduct ag ainst def ects f or a peri od of t wo (2) year s commen cing on t he date of or ...

Manufacturer Troy-Bilt Category Snow Blower

Documents that we receive from a manufacturer of a Troy-Bilt 10030 can be divided into several groups. They are, among others:
- Troy-Bilt technical drawings
- 10030 manuals
- Troy-Bilt product data sheets
- information booklets
- or energy labels Troy-Bilt 10030
All of them are important, but the most important information from the point of view of use of the device are in the user manual Troy-Bilt 10030.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Troy-Bilt 10030, service manual, brief instructions and user manuals Troy-Bilt 10030. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Troy-Bilt 10030.

Similar manuals

A complete manual for the device Troy-Bilt 10030, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Troy-Bilt 10030 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Troy-Bilt 10030.

A complete Troy-Bilt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Troy-Bilt 10030 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Troy-Bilt 10030, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Troy-Bilt 10030, that we can find in the current document
3. Tips how to use the basic functions of the device Troy-Bilt 10030 - which should help us in our first steps of using Troy-Bilt 10030
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Troy-Bilt 10030
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Troy-Bilt 10030 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Troy-Bilt 10030?

Use the form below

If you did not solve your problem by using a manual Troy-Bilt 10030, ask a question using the form below. If a user had a similar problem with Troy-Bilt 10030 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)