English dropdown-ico

Manual Clarion APX401.2

16 pages 0.52 mb
Download

Go to site of 16

Summary
  • Clarion APX401.2 - page 1

    OPERAT I ON INSTALLATION MANUAL 2-CHANNEL POWER AMPLIFIER apx201.qxd 12/5/01 12:57 PM Page 1 ...

  • Clarion APX401.2 - page 2

    2 Channel Power System Amplifier 2 TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Input Connections and Audio Controls . . . . . . . . . . . . . . 3 Connections for Power and Speakers . . . . . . . . . . . . . . ...

  • Clarion APX401.2 - page 3

    Owner’s Manual 3 Owner’s Manual DESCRIPTION The APX201.2 and APX401.2 use an unregulated MOSFET power supply for superior control of output wattage. A toroid-coil transformer yields maximum power transfer with minimal heat loss. Extensive attention to circuit design keeps AM RFI at low levels, so you won’t hear unwanted noise when the level i ...

  • Clarion APX401.2 - page 4

    2 Channel Power System Amplifier 4 • Gain Control - This allows you to set the nominal operating level of the amplifier. The amplifier’s range, 250mV to 2.5V for RCA inputs or 500mV to 5V for speaker level inputs, can accommodate input levels from virtually any brand of source unit. • Bass Boost Control - The amplifier also features a “high ...

  • Clarion APX401.2 - page 5

    Owner’s Manual 5 CONNECTIONS FOR POWER AND SPEAKERS The rear panel of the APX201.2 and APX401.2 contains power and speaker connections as shown below. 1. Left Speaker Output 2. Right Speaker Output 3. Remote Turn-on Input 4. Ground Input 5. Battery +12V Input 6. 25 Amp Fuse (APX201.2) 40 Amp Fuse (APX401.2) Figure 2- 1 2 3 4 5 6 apx201.qxd 12/5/0 ...

  • Clarion APX401.2 - page 6

    2 Channel Power System Amplifier 6 APPLICATIONS The Clarion APX201.2 and APX401.2 2-channel car audio amplifiers can be used in a variety of system applications. Here are some examples to help plan your own installation. Figure 3 - In this application the amplifier is bridged for mono operation to drive a subwoofer. Bridged- Mono Subwoofer System S ...

  • Clarion APX401.2 - page 7

    Owner’s Manual 7 Figure 4 - In this application, the amplifier is used in stereo and drives two full-range (or satellite or subwoofer) speakers. NOTE: A passive crossover must be used with satellite speakers. 2-Channel Full-Range, Satellite, or Subwoofer Stereo System Set X-Over Mode as shown Set X-Over Mode as shown; adjust FREQ to speaker speci ...

  • Clarion APX401.2 - page 8

    2 Channel Power System Amplifier 8 Mixed-Mode Satellite and Subwoofer System FREQ (hz) 80 100 125 150 200 L (mH) 8.0 6.4 5.1 4.2 3.2 C (uF) 497 398 Set X-Over Mode to OFF NOTE: Chart values based on 4 ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table provides component values to create a 6dB per octave c ...

  • Clarion APX401.2 - page 9

    Owner’s Manual 9 INSTALLATION This section lists Mounting and Wiring Precautions prior to installing a Clarion APX201.2 or APX401.2. These safeguards provide enough detail to complete the installation successfully. If you do not have the necessary skills, do not attempt to install the amplifier yourself. Instead, see your authorized Clarion deale ...

  • Clarion APX401.2 - page 10

    2 Channel Power System Amplifier 10 4. A secure, clean ground connection is critical to the performance of your Clarion amplifier. Use the shortest ground wire possible and securely connect to the car chassis to minimize resistance and avoid noise problems. Besure to clean off any paint, prior to making this connection. 5. Add an external fuse on t ...

  • Clarion APX401.2 - page 11

    Owner’s Manual 11 Figure 6. - Electrical connections for the APX201.2 or the APX401.2 apx201.qxd 12/5/01 12:57 PM Page 11 ...

  • Clarion APX401.2 - page 12

    2 Channel Power System Amplifier 12 SETTING THE GAIN After completing the installation, follow these steps to set the Gain Control and then perform the Final System Checks. 1. Turn the Gain Control all the way counter-clockwise. 2. Turn the vehicle’s Ignition Switch to the ON position. Then turn the ON/OFF Switch on the source units to the ON pos ...

  • Clarion APX401.2 - page 13

    Owner’s Manual 13 FINAL SYSTEM CHECKS 1. Start the engine and turn on the source unit. After a two-second delay, slow - ly increase the Volume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to Troubleshooting. Depending on your system design, the levels may beco ...

  • Clarion APX401.2 - page 14

    2 Channel Power System Amplifier 14 Problem Distorted audio. Solution Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.) Problem Audio lacks punch. Solution Speakers wired incorrectly, which causes cancellation of bass frequencies. Check pola ...

  • Clarion APX401.2 - page 15

    Owner’s Manual 15 Frequency Response Signal Noise Ratio THD Input Sensitivity Low Level Input Sensitivity Speaker Level Max. Power Output Cont. Power Output 2-Ohm Stereo Output Bridged Power Dimensions Current Consumption at output @ max power 20Hz ~ 20kHz >100db .05% all channels driven 250mV ~ 2.5 V 500mV - 5V 220w (110 x 2) 100w (50w x 2) @ ...

  • Clarion APX401.2 - page 16

    Clarion Corporation of America 661 W. Redondo Beach Blvd. Gardena, CA 90247-4201 U.S.A. APX201.2.401.2 Rev. 1(11/01) WARRANTY INFORMATION This product is warranted against all defects in material workmanship for a period of one year from the date of original purchase. Clarion ProAudio products except for speakers are covered by a two year warranty ...

Manufacturer Clarion Category Stereo Amplifier

Documents that we receive from a manufacturer of a Clarion APX401.2 can be divided into several groups. They are, among others:
- Clarion technical drawings
- APX401.2 manuals
- Clarion product data sheets
- information booklets
- or energy labels Clarion APX401.2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Clarion APX401.2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Clarion APX401.2, service manual, brief instructions and user manuals Clarion APX401.2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Clarion APX401.2.

Similar manuals

A complete manual for the device Clarion APX401.2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Clarion APX401.2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Clarion APX401.2.

A complete Clarion manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Clarion APX401.2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Clarion APX401.2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Clarion APX401.2, that we can find in the current document
3. Tips how to use the basic functions of the device Clarion APX401.2 - which should help us in our first steps of using Clarion APX401.2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Clarion APX401.2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Clarion APX401.2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Clarion APX401.2?

Use the form below

If you did not solve your problem by using a manual Clarion APX401.2, ask a question using the form below. If a user had a similar problem with Clarion APX401.2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)