Manual Directed Electronics 225A

19 pages 2 mb
Download

Go to site of 19

Summary
  • Directed Electronics 225A - page 1

    CONGRA TULA TIONS ENDP ANEL LA Y OUT FEA TURES / SPECIFICA TIONS ENDP ANEL LA Y OUT (cont.) INST ALLA TION TR OUBLESHOO TING WIRING TR OUBLESHOO TING (cont.) PO WER / GROUND TR OUBLESHOO TING (cont.) CONNECTIONS TR OUBLESHOO TING (cont.) CONNECTIONS (cont.) SYSTEM DIA GRAM 1 / 2 INPUTS / CONNECTIONS BLOCK DIA GRAM INPUTS W ARRANTY CONTENTS (clic k ...

  • Directed Electronics 225A - page 2

    The extended use of a high powered audio system may result in hearing loss or damage. While TUBE DRIVER systems are capable of "Concer t Le v el" volumes with incredible accuracy , they are also designed for you to enjoy at more reasonable levels all of the sonic subtleties created by musicians. Please observe all local sound ordinances. ...

  • Directed Electronics 225A - page 3

    1 Power Bandwidth: 5 Hz -50 KHz T otal Harmonic Distortion: 0.2% or less (A-weighted) Input T opology: Balanced Differential Input Sensitivity: 500mV - 12 volts RMS Input Impedance: 10K Ohms Output Impedance: 2 - 16 Ohms, bridged 4 - 32 Ohms Specifications The TD2200PRO and TD225A amplifiers represent a radical new approach to mobile audio. All vol ...

  • Directed Electronics 225A - page 4

    Fuse Requirements Recommended Fuse Rating f o r TD2200 i s 10 0 Amps Recommended Fuse Rating f o r TD225A is 10 0 Amps Y ou will need to install an in-line fuse or cir cuit breaker in the power wire within 18” of the battery . This fuse or circuit breaker pr otects your vehic le fr om fire in case the power wire shorts to the vehicle bod y . If y ...

  • Directed Electronics 225A - page 5

    Recommended MINIMUM Gauge 3 W arning! Amplifiers Generate Heat! Y ou can mount the TU B E D RIVER in any position, even upside-down. However , you m ust maintain pr oper airflow . Do not install your TU B E D RIVER under carpets or enclose it behind airtight panels. In trunk-mounted applications, be sure to provide venting for air circulation. Let ...

  • Directed Electronics 225A - page 6

    4 W arning! T o prevent a short to ground, disconnect the negative (-) terminal of the system’s battery before you begin. If the power cable shorts to ground, current will continue to flow until the short is opened, the main fuse blows, the battery explodes, or the wire melts. Reconnect the terminal only after y ou make all connections. Grounding ...

  • Directed Electronics 225A - page 7

    5 Follow these simple instructions and ref er to the diagram below to make your speaker connections: • Using at least 16 gauge wire, run wire from the speakers to the amplifier(s) using the same precautions that you followed for running the power , ground, and remote wires • Cut off excess wire • Use wire strippers to strip 1/4 inch of insula ...

  • Directed Electronics 225A - page 8

    6 Mixed Mono Output All multi-channel T UBE D RIVERS are capable of being bridged into a 4- Ohm mono output without switches or bridging modules. Y ou can achieve this mono channel by using the left positive (+) speaker connection and the right negative (-) speaker connection. (Refer to the end panel drawing on the next page.) Note: T otal bridged ...

  • Directed Electronics 225A - page 9

    Input Jacks Y our TUB E D RIVER includes both RCA and Mini-DIN (balanced) inputs. The supplied RCA connections allow you to use TU B E D RIVER with other brands of audio gear . Our Diff erential RCA inputs provide a dr amatic improv ement in noise reduction ov er standard RCA input types . Our fully balanced Mini-DIN connection system f eatures hig ...

  • Directed Electronics 225A - page 10

    8 Input Gain Control There is an Input Gain Control located on the end panel under the RCA input jacks. This is not a v olume control! This control matches the output signal voltage of the source unit to the amplifier inputs. By turning the control clockwise (to the right), the inputs of the amplifier become more sensitive and will allow a weak sig ...

  • Directed Electronics 225A - page 11

    HANDCRAFTED IN THE USA By Precision Power POWER CONNECT POWER W ARM UP 9 P o wer Side 1 3 2 1. PO WER A red light indicates that the amplifiier is turned on (After warm-up sequence). 2. W ARM UP A red light indicated that the tubes are warming up. (Refer to Pg. 4; Remote T urn-on) 3. PO WER / GR OUND After you have securely connected your power and ...

  • Directed Electronics 225A - page 12

    1. SPEAKER OUTPUTS/REMO TE(T urn on) After connecting remote and speaker wires plug in the connector here. 2. GAIN CONTR OL Use this control to match the output level of the head unit to the outputs of the amplifier 3. B ALANCED INPUT Plug in the mini-din output from the LDX-33 crossover , LD-3 line driver, or other balanced source here. 4. -12dB F ...

  • Directed Electronics 225A - page 13

    11 No Sound Amplifier T urning Down at Normal V olume Do you have 12V at the amplifier ’s connections? Is the W ARM UP LED illuminated? YES NO YES The warm up cycle can take up to 40 sec., Is there sound after that? Y ou’re done Is there signal on the RCA ’s? YES NO Does the amp remote (REM) have 12V? Check all connections. Repair as needed Y ...

  • Directed Electronics 225A - page 14

    12 No Sound in One Channel Amplifier T urning D ow n at High V olume YES Reverse the left and right inputs. Check the pre-amp (RCA/Mini-Din) cables for open connections and make corrections. Did you find open connections? NO Y ou’re done SOUND IS NO W IN... Opposite Channel Problem is in the speaker or speaker wire of the silent channel. Check sp ...

  • Directed Electronics 225A - page 15

    13 Noises While the Engine is On Alternator whine: This noise changes in frequency with engine RPM. Check for: . Excessive input le vel . High resistance in cabling or corr oded and/or loose connections . P olarity of the input cab les If the problem persists, check the whines and pops checklist below . Ticks/b uzz: This noise should go faster and ...

  • Directed Electronics 225A - page 16

    14 Noises While the Engine is On or Off System hiss: Distor tion: System hiss is a white noise that occurs even when the engine is off. It is usually due to excessively high gain settings. If the hiss is still audible when you disconnect the input cables from the amplifier , check the input level on the amplifier . If the hiss disappears when you r ...

  • Directed Electronics 225A - page 17

    15 eject VOLUME BASS TREBLE RIGHT LEFT BALANCE TRACK REVERSE FOWARD 1 2 3 4 8 7 6 5 PPI MAR KET ING DPT Trk 1 LD4 Source Unit TD2200 PRO LD3 Studio Driver System 6 Studio Drive r System 6 Subwoofer TD TD TD 2200 2200 FN-6 -2dB 0 dB IN + + + - - -2dB 0 dB - - - - Woofer Midrange Tweeter + FN-6 -2dB 0 dB IN + + + - - -2dB 0 dB - - - - Woofer Midrange ...

  • Directed Electronics 225A - page 18

    16 AMP RCA Right Input DIF. RCA Left Input INPUT ATTENUATION AMP Left Right MINI-DIN Input DIF. GAIN GAIN Left Right BALANCED/RCA Switch BALANCED/RCA Switch B A CK T O CONTENTS ...

  • Directed Electronics 225A - page 19

    Three-Y ear Limited U .S.A. W arranty This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. TUBE DRIVER warrants its products to be free from defects in materials and workmanship under normal use and service for a period of three (3) years from the date of original purchase when the unit i ...

Manufacturer Directed Electronics Category Portable CD Player

Documents that we receive from a manufacturer of a Directed Electronics 225A can be divided into several groups. They are, among others:
- Directed Electronics technical drawings
- 225A manuals
- Directed Electronics product data sheets
- information booklets
- or energy labels Directed Electronics 225A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Directed Electronics 225A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Directed Electronics 225A, service manual, brief instructions and user manuals Directed Electronics 225A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Directed Electronics 225A.

A complete manual for the device Directed Electronics 225A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Directed Electronics 225A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Directed Electronics 225A.

A complete Directed Electronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Directed Electronics 225A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Directed Electronics 225A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Directed Electronics 225A, that we can find in the current document
3. Tips how to use the basic functions of the device Directed Electronics 225A - which should help us in our first steps of using Directed Electronics 225A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Directed Electronics 225A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Directed Electronics 225A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Directed Electronics 225A?

Use the form below

If you did not solve your problem by using a manual Directed Electronics 225A, ask a question using the form below. If a user had a similar problem with Directed Electronics 225A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)