English dropdown-ico

Manual RAD Data comm ARC-101

46 pages 0.75 mb
Download

Go to site of 46

Summary
  • RAD Data comm ARC-101 - page 1

    ARC-101 ATM Rate and Media Converter Installation and Operation Manual Notice This manual c ont ai ns i nfor mation that is prop rietary to RA D D at a Communi cati ons. No part of this p u blicat io n m ay b e r e p r od u ce d in an y fo r m wh at so e ver wit h ou t p r ior wr it t e n ap p r o val by R AD Dat a Communications. No repre s e ntat ...

  • RAD Data comm ARC-101 - page 2

    ...

  • RAD Data comm ARC-101 - page 3

    Warranty This RAD product is warranted against defects in material and workmanship for a period of one year from date of shipment. During the warranty period, RAD will, at its option, either repair or replace products which prove to be defective. For warranty service or repair, this product must be returned to a service facility designated by RAD. ...

  • RAD Data comm ARC-101 - page 4

    Safety Warnings The exclamation point within a triangle is intended to warn the operator or service personnel of operation and maintenance factors relating to the product and its operating environment which could pose a safety hazard. Always observe standard safety precautions during installation, operation and maintenance of this product. Only a q ...

  • RAD Data comm ARC-101 - page 5

    Regulatory Information FCC-15 User Information This equipment has been tested and found to comply with the limits of the Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment gene ...

  • RAD Data comm ARC-101 - page 6

    Declaration of Conformity Manufacturer’s Name: RAD Data Communications Ltd. Manufacturer’s Address: 12 Hanechoshet St. Tel Aviv 69710 Israel declares that the product: Product Name: ARC-101 Conforms to the following standard(s) or other normative document(s): EMC: EN 55022 (1994) Limits and methods of measurement of radio disturbance characteri ...

  • RAD Data comm ARC-101 - page 7

    ARC-101 Installation and Operation Manual i Contents CHAPTER 1 – INTRODUCTION 1.1 General Description .......................................................................................................................... 1-1 1.2 ARC-101 Features................................................................................................... ...

  • RAD Data comm ARC-101 - page 8

    Contents ii ARC-101 Installation and Operation Manual Jumper Settings for E1 and E1/LTU .............................................................................................. ........ 2-12 Jumper Settings for T3 ......................................................................................................... ................ 2-13 CH ...

  • RAD Data comm ARC-101 - page 9

    ARC-101 Installation and Operation Manual iii List of Figures Figure 1-1 ARC-101 Rate Conversion Application ......................................................................... 1-1 Figure 2-1 Installation of a Single Unit ..................................................................................... ..... 2-2 Figure 2-2 Installation of ...

  • RAD Data comm ARC-101 - page 10

    List of Tables iv ARC-101 Installation and Operation Manual List of Tables Table 1-1 Optical Module Characteristics ....................................................................................... 1-5 Table 1-2 Electrical Module Characteristics .................................................................................... 1-5 Table 3-1 ...

  • RAD Data comm ARC-101 - page 11

    ARC-101 Features 1 -1 Chapter 1 Introduction 1 . 1 General Description The ARC-101, ATM Rate & Media Converter, provides transparent ATM rate and media conversion between two interfaces by extracting ATM cells from one interface at one rate and sending them over a different interface at a different rate. The ARC-101 supports a wide variety of A ...

  • RAD Data comm ARC-101 - page 12

    Chapter 1. Introduction ARC-101 Installation & Operation Manual 1 -2 ARC-101 Features 1 . 2 ARC-101 Features This section provides a brief description of the ARC-101's main features. Interfaces Supported The ARC-101 supports a wide variety of ATM data rates and media types, both electrical and optical. The electrical interfaces supported a ...

  • RAD Data comm ARC-101 - page 13

    ARC-101 Installation & Operation Manual Chapter 1. Introduction ARC-101 Features 1 -3 Traffic Management ATM cells are transferred from one interface to the other through an internal bus, the bandwidth of which is 180 Mbps. • Cells that are received with a multiple-bit HEC error are dropped. • Cells received at the slower interface are tran ...

  • RAD Data comm ARC-101 - page 14

    Chapter 1. Introduction ARC-101 Installation & Operation Manual 1- 4 Specifications 1 . 3 Specifications Data Rate Up to 155 Mbps Indicators PWR ON when unit is powered FLT BLINKS when self-test fails (ON during self-test) ATM ON when ATM cells were transmitted and received in the last second and no uncorrected HEC errors were detected. SYNC ON ...

  • RAD Data comm ARC-101 - page 15

    ARC-101 Installation & Operation Manual Chapter 1. Introduction Specifications 1- 5 Ordering ARC-101/# ATM Rate Converter # Specify power supply: AC for 90-260 VAC DC for - 48 VDC ARC-M/@ Interface module for ARC-101 @ Specify module name - see tables below RM-1 Hardware for mounting one unit in a 19" rack. RM-2 Hardware mounting for two u ...

  • RAD Data comm ARC-101 - page 16

    Chapter 1. Introduction ARC-101 Installation & Operation Manual 1- 6 Specifications ...

  • RAD Data comm ARC-101 - page 17

    Site Requirements 2-1 Chapter 2 Installation This chapter contains mechanical and electrical installation procedures for connecting the ARC-101 to the main power supply, as well as cabling the ATM links and monitor (control) port. 2 . 1 General The ARC-101 is delivered completely assembled for bench-top installation. The ARC-101 may be optionally i ...

  • RAD Data comm ARC-101 - page 18

    Chapter 2. Installation ARC-101 Installation & Operation Manual 2-2 Rack Mounting Instructions 2.3 Site Requirements Power The ARC-101 is powered by 90/260 VAC or -48 VDC. The unit should be installed within 1.5 meters (5 ft.) of an easily accessible grounded AC outlet capable of supplying the appropriate voltage (90/260 VAC). Front and Rear Pa ...

  • RAD Data comm ARC-101 - page 19

    ARC-101 Installation & Operation Manual Chapter 2. Installation Cable Connections 2-3 Installation of Two Units Rack adapter components for installing two units include two short side brackets (for rack mounting) and two flat rails (for fastening the two units together) Figure 2- 2 Installation of Two Units To install two units follow these ins ...

  • RAD Data comm ARC-101 - page 20

    Chapter 2. Installation ARC-101 Installation & Operation Manual 2-4 Cable Connections When the ARC-101 is used as a DCE or as a DTE, the RJ-45 pinout is: Pinout DCE DTE Pin 1 Pin 2 Pin 3 DTR Pin 4 GN D GN D Pin 5 TX Data RX Data Pin 6 RX Data TX Data Pin 7 CTS Pin 8 Pin 9 RTS Changing Control Port Mode The ARC-101 is shipped as a DCE. To connec ...

  • RAD Data comm ARC-101 - page 21

    ARC-101 Installation & Operation Manual Chapter 2. Installation ARC-101 Modules 2-5 AC Power Connection The ARC-101's power connector is located on its rear panel (see Figures 2-6 and Figure 2-7 ). AC power should be supplied to the ARC-101 through a 1.5 m (5 ft.) standard power cord terminated by a grounded 3-wire plug. Warning When apply ...

  • RAD Data comm ARC-101 - page 22

    Chapter 2. Installation ARC-101 Installation & Operation Manual 2-6 ARC-101 Modules 2 . 6 ARC-101 Modules Module Characteristics SC13M/155 Module Figure 2- 8 SC13M/155 Module Front Panel Wavelength: 1300 nm Connector: SC Used with: Multimode fiber Protocols supported: STS-3c, STM-1 Coding method: NR Z Optical output into 62.5 micron fiber: -18 ...

  • RAD Data comm ARC-101 - page 23

    ARC-101 Installation & Operation Manual Chapter 2. Installation ARC-101 Modules 2-7 ST13L/155 Module Figure 2- 10 ST13L/155 Module Front Panel Wavelength: 1300 nm Connector: ST Used with: Single mode fiber (LASER) Protocols supported: STS-3c, STM-1 Coding method: NRZ Optical output into 9 micron fiber: -12 dBm (typical) Receiver sensitivity: -3 ...

  • RAD Data comm ARC-101 - page 24

    Chapter 2. Installation ARC-101 Installation & Operation Manual 2-8 ARC-101 Modules UTP/155 Module Figure 2- 12 UTP/155 Module Front Panel Connector: Shielded RJ-45 Used with: UTP Cat 5 Protocols supported: STS-3c, STM-1 Coding method: NRZ Range: 100 m Impedance: 100 Ω Transmit levels: 1v +/- 0.06v Pinout Pin 1 T x + Pin 2 Tx- Pin 3 Pin 4 Pin ...

  • RAD Data comm ARC-101 - page 25

    ARC-101 Installation & Operation Manual Chapter 2. Installation ARC-101 Modules 2-9 E3 Module Figure 2- 13 E3 Module Front Panel Connector: BN C Used with: Coax cable Protocols supported: E3 Coding method: HDB3 Range: 150 m Impedance: 75 Ω Transmit 1v +/- 0.06v T3 Module The transmit pulse shape can be determined by jumpers on the module (ref ...

  • RAD Data comm ARC-101 - page 26

    Chapter 2. Installation ARC-101 Installation & Operation Manual 2-10 ARC-101 Modules E1 and E1/LTU Modules The E1 link interface (Coax/UTP), as well as RX/TX ground reference, can be determined by jumpers on the module (see Figure 2-16 ). Figure 2- 15 E1 Module Front Panel Connector: BNC (RJ-45) Used with: Coax (UTP) Protocols supported: E1 Cod ...

  • RAD Data comm ARC-101 - page 27

    ARC-101 Installation & Operation Manual Chapter 2. Installation ARC-101 Modules 2-11 Inserting and Removing Modules Inserting Modules To insert a module: 1. Turn the unit OFF (disconnect the power cord). 2. Pull on the screws on the module's front panel, so they hang outwards a little. 3. Insert the module onto the sliders, and push the mo ...

  • RAD Data comm ARC-101 - page 28

    Chapter 2. Installation ARC-101 Installation & Operation Manual 2-12 ARC-101 Modules Jumper Settings for E1 and E1/LTU The jumpers JP5, JP6, JP10, JP11 and JP13 are used to select the link interface (Coax or UTP). See Figure 2-16 . Figure 2- 16 E1 and E1/LTU Jumper Locations Note Turn the module upside down in order to see and move the jumpers. ...

  • RAD Data comm ARC-101 - page 29

    ARC-101 Installation & Operation Manual Chapter 2. Installation ARC-101 Modules 2-13 Jumper Settings for T3 Figure 2- 17 T3 Jumper Locations The jumpers JP1 and JP2 (located near the front panel of the module), are used to control the transmit levels, and should be set according to the length of the links (see Figure 2-17 ). T3: JP1: Designated ...

  • RAD Data comm ARC-101 - page 30

    Chapter 2. Installation ARC-101 Installation & Operation Manual 2-14 ARC-101 Modules ...

  • RAD Data comm ARC-101 - page 31

    Operating Procedure 3-1 Chapter 3 Operation The ARC-101 has several LED indicators, providing information on the ARC-101's general status, as well as right and left module status (see Figure 3-1 ). The indicators are ON, OFF, or BLINK, depending on the state of ARC-101. Table 3-1 lists the functions of the front panel indicators. out out out F ...

  • RAD Data comm ARC-101 - page 32

    Chapter 3. Operation ARC-101 Installation & Operation Manual 3-2 Operating Procedure 3 . 1 Operating Procedure Note The interface modules are not hot-swappable. If you install or change modules, make sure to first disconnect power to the ARC-101, and then remove/install modules slowly and carefully (so as not to damage the modules or the ARC-10 ...

  • RAD Data comm ARC-101 - page 33

    ARC-101 Installation & Operation Manual Chapter 3. Operation Operating Procedure 3-3 Figure 3- 2 ARC-101 Block Diagram ...

  • RAD Data comm ARC-101 - page 34

    Chapter 3. Operation ARC-101 Installation & Operation Manual 3-4 Operating Procedure ...

  • RAD Data comm ARC-101 - page 35

    Accessing, Using and Exiting Monitor Mode 4 -1 Chapter 4 Software Management 4 . 1 Introduction Monitor mode enables software management of the ARC-101. Four categories of software management are available: • Monitoring the ARC-101 general information via the General Information window. • Changing default configuration parameters via the Config ...

  • RAD Data comm ARC-101 - page 36

    Chapter 4. Software Management ARC-101 Installation & Operation Manual 4-2 Configuration Window 4 . 3 Screen Explanations Each of the screens shown below is followed by a detailed explanation of the parameters and options appearing in the screen. • The acceptable value range for each parameter, where applicable, is shown in parentheses – &q ...

  • RAD Data comm ARC-101 - page 37

    ARC-101 Installation & Operation Manual Chapter 4. Software Management Configuration Window 4-3 To Save the Configuration: CONFIGURATION 1. System Parameters 2. Left Module 3. Right Module 4. ASCII Terminal Configuration 5. Set Default Parameters 6. Save Changes ESC. Exit • After making all changes, return to the Configuration window, and sel ...

  • RAD Data comm ARC-101 - page 38

    Chapter 4. Software Management ARC-101 Installation & Operation Manual 4-4 Configuration Window The options are 25%, 50%, 75%, 90% and 100%. EFCI Marking (Default - Disable); options: Enable, Disable Enables EFCI marking while FIFO is in congested state. Setting this parameter to Enable causes the EFCI marking of all cells that are received, wh ...

  • RAD Data comm ARC-101 - page 39

    ARC-101 Installation & Operation Manual Chapter 4. Software Management Configuration Window 4-5 Loopback State (Default - Disable); options: Disable, Remote, Internal Setting this parameter to Remote will cause a loopback of the incoming data and clock to the transmit data and clock (this option is not supported with E1). Internal Loopback will ...

  • RAD Data comm ARC-101 - page 40

    Chapter 4. Software Management ARC-101 Installation & Operation Manual 4-6 Performance Monitoring Window 4 . 6 Diagnostics Window The ARC-101 can be tested and reset via the Diagnostics window. To enter the Diagnostics window, select item number 3 in the main menu. The Diagnostics window includes the following options: • General Reset • Mod ...

  • RAD Data comm ARC-101 - page 41

    ARC-101 Installation & Operation Manual Chapter 4. Software Management Performance Monitoring Window 4-7 • Link Status • ATM Status PERFORMANCE MONITORING 1. Link Status 2. ATM Status 3. Reset Counters ESC. Exit Link Status The Link Status window displays: • The number of alarms and errors detected in the last second ("Last Second&qu ...

  • RAD Data comm ARC-101 - page 42

    Chapter 4. Software Management ARC-101 Installation & Operation Manual 4-8 Performance Monitoring Window SONET/SDH Link Status Window LOS Loss of Signal LOF Loss of Frame LOP Loss of Pointer LOC Loss of Cell Delineation SLM Signal Cable Mismatch Line AIS Line Alarm Indication Signal Path AIS Path Alarm Indication Signal Line FERF/RDI Line Far E ...

  • RAD Data comm ARC-101 - page 43

    ARC-101 Installation & Operation Manual Chapter 4. Software Management Performance Monitoring Window 4-9 T3 Link Status Window - Errors/Alarms displayed in PLCP Mode LOS Loss of Signal OOF Out of Frame AIS Alarm Indication Signal Yellow Yellow Alarm PLCP_LOF PLCP Loss of Frame PLCP_Yellow PLCP Yellow A '0'' in the "Last Sec& ...

  • RAD Data comm ARC-101 - page 44

    Chapter 4. Software Management ARC-101 Installation & Operation Manual 4-10 Performance Monitoring Window E3 Link Status Window LOS Loss of Signal OOF Out of Frame LOC Loss of Cell Delineation AIS Alarm Indication Signal RDI Remote Defect Indicator A '0'' in the "Last Sec" columns of the Alarms listed above, indicates t ...

  • RAD Data comm ARC-101 - page 45

    ARC-101 Installation & Operation Manual Chapter 4. Software Management Performance Monitoring Window 4-11 Note The Cells Transmitted counter is not valid in Remote Loopback mode, and the Cells Received counter in not valid in Internal Loopback mode. The counter precision is 1/10,000. ...

  • RAD Data comm ARC-101 - page 46

    Chapter 4. Software Management ARC-101 Installation & Operation Manual 4-12 Performance Monitoring Window ...

Manufacturer RAD Data comm Category Network Card

Documents that we receive from a manufacturer of a RAD Data comm ARC-101 can be divided into several groups. They are, among others:
- RAD Data comm technical drawings
- ARC-101 manuals
- RAD Data comm product data sheets
- information booklets
- or energy labels RAD Data comm ARC-101
All of them are important, but the most important information from the point of view of use of the device are in the user manual RAD Data comm ARC-101.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals RAD Data comm ARC-101, service manual, brief instructions and user manuals RAD Data comm ARC-101. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product RAD Data comm ARC-101.

Similar manuals

A complete manual for the device RAD Data comm ARC-101, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use RAD Data comm ARC-101 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of RAD Data comm ARC-101.

A complete RAD Data comm manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual RAD Data comm ARC-101 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the RAD Data comm ARC-101, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the RAD Data comm ARC-101, that we can find in the current document
3. Tips how to use the basic functions of the device RAD Data comm ARC-101 - which should help us in our first steps of using RAD Data comm ARC-101
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with RAD Data comm ARC-101
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of RAD Data comm ARC-101 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning RAD Data comm ARC-101?

Use the form below

If you did not solve your problem by using a manual RAD Data comm ARC-101, ask a question using the form below. If a user had a similar problem with RAD Data comm ARC-101 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)