Manual Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507

48 pages 2.05 mb
Download

Go to site of 48

Summary
  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 1

    1 Doc. No . Copyright © 1995 Cisco Systems, Inc. All rights reser ved. Cisco 7000 and Cisco 7507 Chassis Replacement Instr uctions 78-1064-02 Product Number s: CHAS-7K, MAS-7K, CHAS-7507, MAS-7507 Customer Order Number: DOC-781064= This document contains instructions for replacing a Cisco 7000 and Cisco 7507 chassis as a spare part. Note W ith a f ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 2

    2 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Product Overview Pr oduct Overview The Cisco 7000 and Cisco 7507 replacement chassis comprise the sheet metal housing, front chassis panels, and all internal components (MAS-7K and MAS-7507, respectiv ely). An optional replacement chassis is shipped with a spare power supply (CHAS-7K and ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 3

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 3 Product Overview Figure 2 Cisco 7507 Chassis Rear View The lower po wer supply bay is the def ault bay for systems with a single supply . The upper bay houses the second power supply in systems with redundant po wer . Power supplies slide into the bays and must be fully inserted before th ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 4

    4 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Product Overview Figure 3 P ower Suppl y Safety Interloc ks T o the right of the po wer supply bays, the processor slots house the processor modules. In the Cisco 7000, the RP is always located in the f ar right slot (the RP slot), and the SP (or SSP) is always located in the adjacent slo ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 5

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 5 Product Overview Figure 5 Cisco 7507 System Backplane Slot K ey Guides Spring-loaded ejector lev ers help to ensure that the processor modules are either fully inserted in the backplane or fully dislodged from it. It is particularly important to use the ejector lev ers when removing or in ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 6

    6 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Prerequisites Prerequisites Before you mov e a chassis or any of the system components, re vie w the safety guidelines and requirements in this section and ensure that you hav e the necessary parts and tools you will need. W arning This warning symbol means danger . Y ou are in a situatio ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 7

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 7 Prerequisites Saf ety Guidelines The follo wing guidelines will help to ensure your safety and protect the equipment. This list is not inclusiv e of all potentially hazardous situations, so be alert . W arning Before working on a system that has an on/of f switch, turn OFF the po wer and ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 8

    8 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Prerequisites Lifting the Chassis Saf ely The chassis weighs 76 pounds when empty (no processor modules or po wer supplies installed) and 145 pounds when fully configured with two po wer supplies and all interface slots populated. Whene ver you lift the chassis or any hea vy object, foll ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 9

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 9 Prerequisites Saf ety with Electricity Follo w these basic guidelines when working with an y electrical equipment: • Before beginning an y procedures, locate the emergenc y po wer-of f switch for the room in which you are working. • Ne ver assume that po wer has been disconnected from ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 10

    10 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Prerequisites • Multimode Fiber Distributed Data Interf ace (FDDI) connectors use small plastic arms on two sides of the connector that act like springs and are constrained by the inside of the connector port. T o remov e a multimode cable from a FIP port, pinch the two plastic arms in ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 11

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 11 Unpacking the Chassis Follo wing are guidelines for pre venting ESD damage: • Always use an ESD strap and ensure that it mak es good skin contact. • When removing or installing an LED board, connect the equipment end of the ground strap to an unpainted surface of the chassis, such as ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 12

    12 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Replacing a Rack-Mounted Chassis • If there is sufficient space a v ailable in the same rack (or an adjacent rack) to install the replacement (empty) chassis before you remove the existing system, you can minimize downtime and av oid ha ving to disconnect network interface cables by l ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 13

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 13 Replacing a Rack-Mounted Chassis Adding a New Chassis to the Rac k If there is suf ficient rack space to install the replacement chassis before you remove the e xisting system, proceed as follows. Step 1 Follo w the instructions in the section “Unpacking the Chassis” on page 11 to u ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 14

    14 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Replacing a Rack-Mounted Chassis Caution T o prev ent damage, ne ver attempt to lift or support the front of the chassis with the plastic front panels. The panels can break away and allo w the chassis to drop. Step 9 T o remov e the empty chassis from the rack, position one person in the ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 15

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 15 Replacing a Rack-Mounted Chassis Caution If the existing chassis is installed in an enclosed rack, or if a po wer strip or other rack fixture blocks access to the power supply bays, you might ha ve to remo ve the e xisting system with the po wer supplies intact, and then install them in ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 16

    16 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Replacing a Rack-Mounted Chassis Step 5 On the front of the rack, use a 1/4-inch flat-blade scre wdriv er to loosen and remov e the four binder-head scre ws that secure the left and right ears to the front mounting strips on the equipment rack. (See Figure 7.) Keep the remov ed scre ws ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 17

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 17 Replacing a Rack-Mounted Chassis Step 6 Position one person in the back of the rack to push the chassis out the front, and position two people in front of the rack to support the chassis and lo wer it to the floor as it is pushed forward out of the rack. Slo wly push the chassis out of ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 18

    18 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Moving System Components Moving System Components The follo wing sections describe the procedures for removing each processor module and po wer supply from the old chassis and installing it in the new chassis. Mo ve and install all processor modules before you mov e the power supplies. I ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 19

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 19 Moving System Components Failure to use the ejector le vers could result in a partial backplane connection and subsequent system crash. Also, be sure to tighten both the top and bottom captiv e installation scre ws on each module to ensure that it will remain seated properly . When repla ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 20

    20 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Moving System Components Step 2 Place your thumbs on the upper and lower ejector le v ers and simultaneously push the top le ver up and the bottom le ver do wn to release the board connector from the backplane. (See Figure 8c.) Step 3 Grasp the carrier handle with one hand and place your ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 21

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 21 Moving System Components Step 6 While keeping the carrier at a 90-degree orientation to the backplane, carefully slide the carrier into the slot until the back of the faceplate makes contact with the ejector lev ers. (See Figure 8b .) Step 7 Using the thumb and forefinger of each hand, ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 22

    22 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Moving System Components Note Use both hands to handle po wer supplies. Each weighs 20 pounds. If the power supply resists when you attempt to pull it out of the bay , the switch is probably not fully in the OFF (O) position, or the captiv e installation scre w at the top of the supply i ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 23

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 23 Moving System Components Step 13 T o secure the A C-input cable in the po wer supply A C receptacle, push up the cable retention clip up until it snaps into place around the connector . T o secure the DC-input cable to the power supply , attach the three leads to the terminal block, and ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 24

    24 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions V erifying the Installation V erifying the Installation This section provides instructions for first ensuring that all connections are secure and then for restarting the system and verifying that it operates correctly . If the system does not start up and operate as expected, the troubl ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 25

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 25 Verifying the Installation Step 2 After turning on the lower po wer supply , turn ON the upper power supply (if one is present) for redundant po wer . The upper po wer LED on the front of the chassis will go on. Step 3 While the system initializes, the boot error LED on the RP (or the CP ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 26

    26 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions V erifying the Installation T roubleshooting the Installation Follo w the procedures in this section if the system does not restart and boot as e xpected. Most often, problems you encounter while replacing the components in a new chassis are caused by po wer supplies or processor modules ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 27

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 27 Verifying the Installation In systems with a single DC-input power supply , and in systems with redundant power when both po wer supplies are shutting down, the out fail LED goes on momentarily as the system ramps do wn, but goes out when the po wer supply has completely shut do wn. In s ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 28

    28 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions V erifying the Installation In systems with a single power supply , and in systems with redundant power when both po wer supplies are being shut down, the DC f ail (or output fail) LED goes on momentarily as the system ramps do wn, but goes out when the po wer supply has completely shut ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 29

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 29 Verifying the Installation Route Processor LEDs (Cisco 7000) Figure 15 shows the LEDs on an RP installed in the chassis. The three LEDs on the RP indicate the system and RP status. When the system is turned on or restarted, the boot error LED goes on for one or two seconds, then goes out ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 30

    30 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions V erifying the Installation Route Switch Pr ocessor LEDs (Cisco 7507) Figure 16 shows the tw o LEDs on the RSP2. They indicate the system and RSP2 status. The normal LED goes on to indicate that the system is operational. During normal operation, the CPU halt LED on the RSP2 should be of ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 31

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 31 Verifying the Installation Interface Processor , SP , and SSP LEDs The SP or SSP (on the Cisco 7000) and all interface processors contain an enabled LED. When on, this LED indicates that the SP or interface processor is operational and that it is po wered up. It does not necessarily mean ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 32

    32 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions V erifying the Installation Step 3 Listen for the system blo wer . It generates about 60 dB, so you should immediately hear it start operating. If you determine that the power supplies are functioning normally and that the blower is f aulty , contact a service representative. If the syst ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 33

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 33 Verifying the Installation Step 7 When the system boot is complete, the RP (or RSP2) begins to initialize the interface processors. During this initialization, the LEDs on each interface processor beha ve dif ferently (most flash on and off). The enabled LED on each interf ace processor ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 34

    34 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions V erifying the Installation Figure 17 Cisco 7000 P ort Configuration W orksheet Circle one: AIP/CIP/EIP/FIP/ FSIP/HIP/TRIP 0/0 0/1 0/2 0/3 0/4 0/5 0/6 0/7 Slot 3 3/0 3/1 3/2 3/3 3/4 3/5 3/6 3/7 Slot 4 4/0 4/1 4/2 4/3 4/4 4/5 4/6 4/7 Router name Location Prepared by Date H1324a Slot 1 1/ ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 35

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 35 Verifying the Installation Figure 18 Cisco 7507 P ort Configuration W orksheet Circle one: AIP/CIP/EIP/FEIP/FIP/ FSIP/HIP/TRIP/MIP 0/0 0/1 0/2 0/3 0/4 0/5 0/6 0/7 Slot 3 RSP2 Slot 4 4/0 4/1 4/2 4/3 4/4 4/5 4/6 4/7 Router name Location Prepared by Date H3889 Slot 1 1/0 1/1 1/2 1/3 1/4 1/ ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 36

    36 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions T ranslated Safety W arnings T ranslated Safety W arnings Follo wing are translations of the safety warnings that appear throughout this publication: P ower Disconnection W ar ning W arning Before working on a system that has an on/of f switch, turn OFF the po wer and unplug the po wer c ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 37

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 37 Translated Safety Warnings V ar oitus Älä kosk eta virtalähdettä virtajohdon ollessa kytkettynä. V irrankatkaisimella v arustetuissa järjestelmissä on virtalähteen sisällä jäljellä verkkojännite, v aikka virrankatkaisin on katkaistu-asennossa virtajohdon ollessa kytkettynä. ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 38

    38 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions T ranslated Safety W arnings Attention A vant de tra v ailler sur un châssis ou à proximité d'une alimentation électrique, débrancher le cordon d'alimentation des unités en courant alternatif ; couper l'alimentation des unités en courant continu au niv eau du disjon ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 39

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 39 Translated Safety Warnings ¡Advertencia! Puede ser que este equipo posea más de un cable de alimentación. Para reducir el riesgo de descarga eléctrica, desenchuf ar los dos cables antes de proceder al mantenimiento de la unidad. V arning! Denna enhet kan vara försedd med mer än en ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 40

    40 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions T ranslated Safety W arnings Adv arsel Det er nødv endig med to personer for å løfte kabinettet. T a tak i kabinettet under den nedre kanten, og løft med begge hender . Unngå personskade ved å holde ryggen rett og løfte med bena, ikke ryggen. Unngå skade på kabinettet og kompone ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 41

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 41 Translated Safety Warnings A vvertenza Prima di svolgere una qualsiasi delle procedure seguenti, v erificare che il circuito CC non sia alimentato. Per verificare che tutta l’alimentazione sia scolle gata (OFF), individuare l’interruttore automatico sul quadro strumenti che aliment ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 42

    42 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions T ranslated Safety W arnings Chassis W arning—Rack-Mounting and Servicing W arning T o pre vent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The follo wing guidelines are provided to ensure you ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 43

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 43 Translated Safety Warnings W arnung Zur V ermeidung v on Körperverletzung beim Anbringen oder W arten dieser Einheit in einem Gestell müssen Sie besondere V orkehrungen treffen, um sicherzustellen, daß das System stabil bleibt. Die folgenden Richtlinien sollen zur Gewährleistung Ihre ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 44

    44 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions T ranslated Safety W arnings V arning! För att undvika kroppsskada när du installerar eller utför underhållsarbete på denna enhet på en ställning måste du vidta särskilda försiktighetsåtgärder för att försäkra dig om att systemet står stadigt. Följande riktlinjer ges fö ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 45

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 45 Translated Safety Warnings Attention Quand des fils torsadés sont nécessaires, utiliser des douilles terminales homologuées telles que celles à circuit fermé ou du type à plage ouverte a vec cosses rebroussées. Ces douilles terminales doiv ent être de la taille qui con vient aux ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 46

    46 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions T ranslated Safety W arnings Attention La figure illustre le bloc de connexion de l'alimentation en courant continu. Câbler l'alimentation en courant continu en fixant les cosses qui con viennent aux extrémités câblées conformément au schéma. La séquence de câblage ? ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 47

    Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 47 Translated Safety Warnings W arnung Nach V erdrahtung des Gleichstrom-Netzgeräts entfernen Sie das Klebeband v om Schaltergrif f des Unterbrechers und schalten den Strom erneut ein, indem Sie den Grif f des Unterbrechers auf EIN stellen. A vvertenza Dopo aver ese guito il cablaggio dell ...

  • Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - page 48

    48 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Cisco Information Online Cisco Inf ormation Online Cisco Information Online (CIO) is Cisco Systems’ primary , real-time support channel. Maintenance customers and partners can self-register on CIO to obtain additional content and services. A vailable 24 hours a day , 7 days a week, CIO ...

Manufacturer Cisco Category Network Router

Documents that we receive from a manufacturer of a Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 can be divided into several groups. They are, among others:
- Cisco technical drawings
- 7000 and 7507 Chassis CHAS-7507 manuals
- Cisco product data sheets
- information booklets
- or energy labels Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507, service manual, brief instructions and user manuals Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507.

Similar manuals

A complete manual for the device Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507.

A complete Cisco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 - which should help us in our first steps of using Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507?

Use the form below

If you did not solve your problem by using a manual Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507, ask a question using the form below. If a user had a similar problem with Cisco Cisco 7000 and Cisco 7507 Chassis CHAS-7507 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)