Manual DCS -CGT

14 pages 0.98 mb
Download

Go to site of 14

Summary
  • DCS -CGT - page 1

    Dyn a mic Coo king S y s tem s, In c. The Professional Restaurant Gas Tandoor Use and Installation Guide Models:  DCS-CGT ...

  • DCS -CGT - page 2

    1 A M e ss a ge T o Ou r C u st o m e r s FOR YOUR SAFETY Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance. If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. If odor continues, immediately call your gas supplier. WARNING Improper installation, a ...

  • DCS -CGT - page 3

    2 In t roduction / S af ety P recaution s Thank you for choosing your new Dynamic Cooking Systems Professional Restaurant Gas Tandoor. Our prod- ucts are designed to be safe and reliable when properly cared for and used reasonably. Periodical inspections are recommended by your service agency or dealer. Installation, maintenance, and repairs should ...

  • DCS -CGT - page 4

    3 Fe a t u re s The Professional T andoor by DCS comes with these standard features. ● Input rating = 70,0000 BTU/HR ● Overall dimensions 34 ” wide x 36 ” high x 35 ” deep. ● 1 inch thick ceramic bowl to retain heat longer and more evenly. ● All stainless steel exterior. ● Ceramic bowl preheats to 800F in approx. 45 minutes. ● Two ...

  • DCS -CGT - page 5

    4 Sp e c i f ication s EXTERIOR DIMENSION ● WIDTH: 34 ” (864mm) ● HEIGHT (w/6 ” legs): 36 ” (915mm) ● DEPTH: 35 ” (889mm) SHIPPING WEIGHT DIMENSIONS ● MINIMUM ENTRY CLEARANCE: Crated 39 1/4 ” - Uncrated 34 1/4 ” GAS REQUIREMENTS ● MANIFOLD PRESSURE: 6 ” W.C. Natural Gas - 10 ” W.C. Propane Gas ● MANIFOLD SIZE: 3/4 ” NP ...

  • DCS -CGT - page 6

    5 Pr e-In s t a l l a t i o n Important: Safe and satisfactory operation of your equipment depends on its proper installation. Installation must conform to local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-1988 (or latest edition). The Canadian CAN/CGA-B149.1 Natural Gas Installation code, and CAN / CGA B14 ...

  • DCS -CGT - page 7

    UNP ACKING Check that the container is upright. Use outward prying no hammering to remove the carton. Check the Tandoor for visible damage. If such damage has occurred, do not refuse shipment, but contact the carrier and file the appropriate freight claims. Do not contact the factory, as responsibility for shipping damage is between the carrier and ...

  • DCS -CGT - page 8

    7 In s t a lling T he T andoo r PRESSURE REGULA TING The Tandoor and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at pressures in excess of 1/2 psig. The Tandoor must be isolated from the gas supply piping system by closing its individual manual shut-off valve during ...

  • DCS -CGT - page 9

    8 In i t i a l St a r t-u p / Op e r a t i o n PLACEMENT OF LA V A ROCK Place a layer of lava rock on the stainless steel pan located directly above the burners. PILOT & MAIN BURNERS All Tandoors are tested and adjusted before leaving the factory, effectively matching them to sea level condi- tions. Adjustments to assure proper operation may be ...

  • DCS -CGT - page 10

    9 Cleaning and Maintenance GENERAL New units are wiped clean at the factory to remove any visible signs of dirt, oil, grease remaining from the man- ufacturing process. They should be washed thoroughly with hot soapy water to remove any installation dust or debris before being used for food preparation. Also wash any accessories shipped with the Ta ...

  • DCS -CGT - page 11

    10 Pa r t s L i s t ITEM DESCRIPTION PART NO. 1M anual Valve 3/8 13034 2 Knob Chrome 14020-02 3 Ceramic Bowl 14272 4 Logo DCS Medallion Series 17301 5 Leg Assembly 18036-1 6 Lid W/Assembly 20047 7 Lid Handle 20049 8 Manifold W/Assembly 20051 9 Crumb Tray 20064 10 Crumb Tray Slide R/H 20065-01 11 Crumb Tray Slide L/H 20065-02 12 Front Panel 20068 13 ...

  • DCS -CGT - page 12

    11 T roub le s hooting These troubleshooting procedures must be carried out only by a factory authorized agency for warranty repair. The problems and possible solutions given below cover those most commonly encountered. PILOT BURNER MALFUNCTION Pilot will not ignite; no evidence of gas at pilot burner: ● Check that the gas valve is open and gas i ...

  • DCS -CGT - page 13

    12 Wa r ranty For warranty service, contact your local DCS authorized service agency. Provide him with the Model Number, Serial Number, and date of installation, and a brief description of the problem. If you need assistance in locating the authorized service agency in your area please contact our DCS Customer Service Department for an authorized s ...

  • DCS -CGT - page 14

    Part No. 17331 Litho in USA 08/2000 As product improvement is an ongoing process at DCS, we reserve the right to change specifications or design without notice. 5800 Skylab Road, Huntington Beach, CA. 92647 Tel: (714) 372-7000 Fax: (714) 372-7001 Parts/Customer Service (888) 281-5698 ...

Manufacturer DCS Category Gas Grill

Documents that we receive from a manufacturer of a DCS -CGT can be divided into several groups. They are, among others:
- DCS technical drawings
- -CGT manuals
- DCS product data sheets
- information booklets
- or energy labels DCS -CGT
All of them are important, but the most important information from the point of view of use of the device are in the user manual DCS -CGT.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals DCS -CGT, service manual, brief instructions and user manuals DCS -CGT. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product DCS -CGT.

Similar manuals

A complete manual for the device DCS -CGT, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use DCS -CGT by users. Manuals are usually written by a technical writer, but in a language understandable to all users of DCS -CGT.

A complete DCS manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual DCS -CGT - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the DCS -CGT, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the DCS -CGT, that we can find in the current document
3. Tips how to use the basic functions of the device DCS -CGT - which should help us in our first steps of using DCS -CGT
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with DCS -CGT
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of DCS -CGT in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning DCS -CGT?

Use the form below

If you did not solve your problem by using a manual DCS -CGT, ask a question using the form below. If a user had a similar problem with DCS -CGT it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)