Manual Mitsubishi Electronics OC376

96 pages 7.16 mb
Download

Go to site of 96

Summary
  • Mitsubishi Electronics OC376 - page 1

    TECHNICAL & SER VICE MANUAL SPLIT -TYPE, HEA T PUMP AIR CONDITIONERS CONTENTS 1. TECHNICAL CHANGES ···································2 2. SAFETY PRECAUTION ····································2 3. OVERVIEW OF UNITS······························ ...

  • Mitsubishi Electronics OC376 - page 2

    2 2 SAFETY PRECAUTION Cautions for units utilizing refrigerant R410A CAUTIONS RELA TED TO NEW REFRIGERANT Use new refrigerant pipes. Make sure that the inside and outside of refrige- rant piping are clean and it has no contamination such as sulfur hazardous for use, oxides, dirt, shredded particles, etc. In addition, use pipes with specified thickn ...

  • Mitsubishi Electronics OC376 - page 3

    3 Gravimeter Unit [3] Service tools Use the below service tools as exclusive tools for R410A refrigerant. No. T ool name Specifications 1 Gauge manifold ·Only for R410A ·Use the existing fitting specifications . (UNF1/2) ·Use high-tension side pressure of 5.3MPa·G or over . 2 Charge hose ·Only for R410A ·Use pressure performance of 5.09MPa·G ...

  • Mitsubishi Electronics OC376 - page 4

    4 Cautions for refrigerant piping work New refrigerant R410A is adopted for replacement inverter series. Although the refrigerant piping work for R410A is same as for R22, exclusive tools are necessary so as not to mix with different kind of refrigerant. Furthermore as the working pressure of R410A is 1.6 time higher than that of R22, their sizes o ...

  • Mitsubishi Electronics OC376 - page 5

    Branching pipe components Branch header (2 branches) Branch header (4 branches) Branch header (8 branches) CMY -Y62-G-E CMY -Y64-G-E CMY -Y68-G-E Outdoor unit Capacity 50% ~130% of outdoor unit capacity *2 T ype 15(VHMA)/20(VHM) ~T ype 140 1~ 8 unit Indoor unit that can be connected Number of units T otal system wide capacity 5HP PUMY -P125VHM PUMY ...

  • Mitsubishi Electronics OC376 - page 6

    6 3-2. UNIT SPECIFICA TIONS (2) Method for identifying MUL TI-S model (1) Outdoor Unit ■ Indoor unit < When using Model 80 > ■ Outdoor unit <When using model 125 > (3) Operating temperature range Notes D.B. : Dry Bulb T emperature W .B. : Wet Bulb T emperature w 1. 10~46°C DB : In case of connecting PKFY -P20/P25 type indoor unit. ...

  • Mitsubishi Electronics OC376 - page 7

    7 4 SPECIFICA TIONS *3 *3 *3 *3 *3 *3 *3 *3 PUMY -P125VHM PUMY -P125VHMA Cooling Capacity kW 14.0 Heating Capacity kW 16.0 Input (Cool) kW 4.32 Input Current (Cool) A 20.0/19.1/18.3, 20.0 Input (Heat) kW 4.33 Input Current (Heat) A 20.0/19.1/18.3, 20.0 EER (Cool) 3.24 COP (Heat) 3.69 Connectable indoor units (Max.) 8 Max. Connectable Capacity kW 18 ...

  • Mitsubishi Electronics OC376 - page 8

    8 5 DA T A 5-1. COOLING AND HEA TING CAP ACITY AND CHARACTERISTICS 5-1-1. Method for obtaining system cooling and heating capacity: T o obtain the system cooling and heating capacity and the electrical characteristics of the outdoor unit, first add up the ratings of all the indoor units connected to the outdoor unit (see table below), and then use ...

  • Mitsubishi Electronics OC376 - page 9

    9 5-2. ST ANDARD CAP ACITY DIAGRAM 5-2-1. PUMY -P100VHM PUMY -P100VHMA *Before calculating the sum of total capacity of indoor units, please convert the value into the kW model capacity following the formula on 5-1-1. T otal capacity of Capacity ( kW ) P ower Consumption ( kW ) Current ( A ) /220V Current ( A ) /230V Current ( A ) /240V indoor unit ...

  • Mitsubishi Electronics OC376 - page 10

    10 T otal capacity of Capacity ( kW ) P ower Consumption ( kW ) Current ( A ) /220V Current ( A ) /230V Current ( A ) /240V indoor units* Cooling Heating Cooling Heating Cooling Heating Cooling Heating Cooling Heating 111 11.10 12.38 3.27 3.62 15.1 16.7 14.5 16.0 13.9 15.3 112 11.20 12.50 3.34 3.66 15.4 16.9 14.8 16.2 14.1 15.5 113 11.22 12.51 3.35 ...

  • Mitsubishi Electronics OC376 - page 11

    11 T otal capacity of Capacity(kW) Power Consumption(kW) Current(A)/ 220V Current(A)/ 230V Current(A)/ 240V indoor units* Cooling Heating Cooling Heating Cooling Heating Cooling Heating Cooling Heating 70 7.00 7.88 71 7.10 8.00 72 7.20 8.1 1 73 7.30 8.22 74 7.40 8.33 75 7.50 8.44 76 7.60 8.56 77 7.70 8.67 78 7.80 8.78 79 7.90 8.89 80 8.00 9.00 81 8 ...

  • Mitsubishi Electronics OC376 - page 12

    12 T otal capacity of Capacity(kW) Power Consumption(kW) Current(A)/ 220V Current(A)/ 230V Current(A)/ 240V indoor units* Cooling Heating Cooling Heating Cooling Heating Cooling Heating Cooling Heating 131 13.10 14.88 132 13.20 15.00 133 13.30 15.13 134 13.40 15.25 135 13.50 15.38 136 13.60 15.50 137 13.70 15.63 138 13.80 15.75 139 13.90 15.88 140 ...

  • Mitsubishi Electronics OC376 - page 13

    13 5-2-3. PUMY -P140VHM PUMY -P140VHMA *Before calculating the sum of total capacity of indoor units, please convert the value into the kW model capacity following the formula on 5-1-1. T otal capacity of Capacity ( kW ) P ower Consumption ( kW ) Current ( A ) /220V Current ( A ) /230V Current ( A ) /240V indoor units* Cooling Heating Cooling Heati ...

  • Mitsubishi Electronics OC376 - page 14

    14 T otal capacity of Capacity ( kW ) P ower Consumption ( kW ) Current ( A ) /220V Current ( A ) /230V Current ( A ) /240V indoor units* Cooling Heating Cooling Heating Cooling Heating Cooling Heating Cooling Heating 146 14.60 16.80 4.92 5.23 22.7 24.2 21.7 23.1 20.8 22.2 147 14.70 16.93 4.97 5.27 23.0 24.4 22.0 23.3 21.1 22.3 148 14.80 17.06 5.02 ...

  • Mitsubishi Electronics OC376 - page 15

    15 5-3. CORRECTING COOLING AND HEA TING CAP ACITY 5-3-1. Correcting Capacity for Changes in Air Conditions (1) The performance curve charts (Figure 1, 2) show the change ratio of capacity and input (power consumption) according to the indoor and outdoor temperature condition when defining the rated capacity (total capacity) and rated input under th ...

  • Mitsubishi Electronics OC376 - page 16

    16 5-3-2. Correcting Capacity for Changes in the Length of Refrigerant Piping (1) During cooling, to obtain the ratio (and the equivalent piping length) of the outdoor units rated capacity and the total in-use indoor capacity , first find the capacity ratio corresponding to the standard piping length from Figure 3, and then multiply by the cooling ...

  • Mitsubishi Electronics OC376 - page 17

    17 5-4. NOISE CRITERION CURVES 1.5m 1m MICROPHONE UNIT GROUND 90 80 70 60 50 40 30 20 10 63 125 250 500 1000 2000 4000 8000 APPROXIMA TE THRESHOLD OF HEARING FOR CONTINUOUS NOISE OCT A VE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 µ bar) BAND CENTER FREQUENCIES, Hz NC-60 NC-50 NC-40 NC-30 NC-20 NC-70 PUMY -P100VHM PUMY -P100VHMA COOLING MODE HEA ...

  • Mitsubishi Electronics OC376 - page 18

    18 6 OUTLINES AND DIMENSIONS 45 40 65 92 27 55 23 73 63 Rear piping hole (Knockout) Rear trunking hole (Knockout) Power supply wiring hole (2- [ 27Knockout) 19 55 92 75 40 73 63 23 27 92 Right piping hole (Knockout) Right trunking hole (Knockout) Power supply wiring hole (2- [ 27Knockout) n92 92 65 45 40 27 55 23 73 63 Front piping hole (Knockout) ...

  • Mitsubishi Electronics OC376 - page 19

    19 45 40 65 92 27 55 23 73 63 Rear piping hole (Knockout) Rear trunking hole (Knockout) Power supply wiring hole (2- [ 27Knockout) 19 55 92 75 40 73 63 23 27 92 Right piping hole (Knockout) Right trunking hole (Knockout) Power supply wiring hole (2- [ 27Knockout) n92 92 65 45 40 27 55 23 73 63 Front piping hole (Knockout) Front trunking hole (Knock ...

  • Mitsubishi Electronics OC376 - page 20

    20 7 WIRING DIAGRAM SYMBOL NAME SYMBOL NAME SYMBOL NAME SYMBOL NAME TB1 Terminal Block <Power Supply> TB3 Terminal Block <Transmission> TB7 Terminal Block <Centralized Control> MC Motor for Compressor MF1,MF2 Fan Motor 21S4 Solenoid Valve <Four way valve> SV1 Solenoid Valve <Bypass valve> TH3 Thermistor <Outdoor Pip ...

  • Mitsubishi Electronics OC376 - page 21

    21 12 34 56 78 [Example] When the compressor and SV1 are turned on during cooling operation. Bit Indication 1 Compressor operated 2 52C 3 21S4 4 SV1 5 (SV2) 67 — — 8 Always lit When fault requiring inspection has occurred The LED alternately indicates the inspection code and the location of the unit in which the fault has occurred. NOTES: 1.Ref ...

  • Mitsubishi Electronics OC376 - page 22

    22 8 NECESSAR Y CONDITIONS FOR SYSTEM CONSTRUCTION 8-1. TRANSMISSION SYSTEM SETUP 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 051 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 056 001 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 010 101 1 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 ...

  • Mitsubishi Electronics OC376 - page 23

    23 8-2. REFRIGERANT SYSTEM DIAGRAM PUMY -P100VHM PUMY -P125VHM PUMY -P140VHM PUMY -P100VHMA PUMY -P125VHMA PUMY -P140VHMA Refrigerant Gas pipe <5/8> Refrigerant Liquid pipe <3/8> Check valve <Low pressure> Accumulator Thermistor <Low pressure saturation temperature> (TH6) Bypass valve (SV1) Capillary tube Check valve <Hig ...

  • Mitsubishi Electronics OC376 - page 24

    24 8-3. SYSTEM CONTROL Example for the System • Example for wiring control cables, wiring method and address setting, permissible lengths, and the prohibited items are liste d in the standard system with detailed explanation. A. Example of a M-NET remote controller system (address setting is necessary .) Example of wiring control cables Wiring Me ...

  • Mitsubishi Electronics OC376 - page 25

    25 • Name, Symbol and the Maximum Remote controller Units for Connection Name Outdoor unit Indoor unit Symbol OC IC RC Maximum units for connection Permissible Lengths Prohibited items Longest transmission cable length (1.25 mm 2 ) L 1 + L 2 , L 2 + L 3 , L 3 + L 1 [ 200m Remote controller cable length 1. If 0.5 to 1.25 mm 2 R 1 , R 2 [ 10m 2. If ...

  • Mitsubishi Electronics OC376 - page 26

    26 B. Example of a group operation system with 2 or more outdoor units and a M-NET remote controller . (Address settings are necessary .) Examples of T ransmission Cable Wiring Wiring Method Address Settings slla. Always use shielded wire when making connections between the outdoor unit (OC) and the indoor unit (IC), as well for all OC-OC, and IC-I ...

  • Mitsubishi Electronics OC376 - page 27

    27 • Name, Symbol, and the Maximum Units for Connection Permissible Length Prohibited items • Longest length via outdoor units : L 1 +L 2 +L 3 +L 4, L 1 +L 2 +L 3+ L 5, L 1 +L 2 +L 6 +L 7 [ 500 meters (1.25mm 2 ) • Longest transmission cable length : L 1, L 3 +L 4 , L 3+ L 5 , L 6, L 2 +L 6 , L 7 [ 200 meters (1.25mm 2 ) • Remote controller ...

  • Mitsubishi Electronics OC376 - page 28

    28 C. Example of a MA remote controller system (address setting is not necessary .) NOTE : In the case of same group operation, need to set the address that is only main indoor unit. Example of wiring control cables Wiring Method and Address Setting • 1 remote controller for each indoor unit. 1. Standard operation 2. Operation using two remote co ...

  • Mitsubishi Electronics OC376 - page 29

    29 Permissible Lengths Prohibited items Longest transmission cable length L 1 + L 2 [ 200m (1.25 mm 2 ) MA remote controller cable length R 1 , R 2 [ 200m (0.3 ~ 1.25 mm 2 ) MA M1 M2 TB5 S1 2 TB15 00 IC AB M1 M2 TB3 S M1 M2 TB7 00 OC S MA M1 M2 TB5 S1 2 TB15 00 IC AB MA M1 M2 TB5 S1 2 TB15 00 IC AB M1 M2 TB3 S M1 M2 TB7 00 OC S M1 M2 TB5 S1 2 TB15 ...

  • Mitsubishi Electronics OC376 - page 30

    30 D. Example of a group operation with 2 or more outdoor units and a MA remote controller . (Address settings are necessary .) Examples of T ransmission Cable Wiring A B C E D M1 M2 S TB7 IC (51) M1 M2 1 2 S TB5 TB15 12 TB15 12 TB15 12 TB15 12 TB15 12 TB15 12 TB15 MA (01) IC M1 M2 S TB5 (03) IC M1 M2 S TB5 (02) IC M1 M2 S TB5 (04) IC M1 M2 S TB5 ( ...

  • Mitsubishi Electronics OC376 - page 31

    31 • Name, Symbol, and the Maximum Units for Connection Permissible Length Prohibited items • Never connect together the terminal blocks (TB5) for transmission wires for indoor units (IC) that have been connected to different outdoor units (OC). • M-NET remote controller and MA remote controller cannot be connected with the indoor unit of the ...

  • Mitsubishi Electronics OC376 - page 32

    32 9 TROUBLESHOOTING Operation procedure 1 T urn on the main power supply of all units at least 12 hours before test run. ”HO” appears on display panel for 3 min. 2 12 hours later , press TEST RUN button twice to perform test run. “TEST RUN “ appears on display panel. 3 Press OPERA TION SWITCH button to make sure that air blows out. 4 Selec ...

  • Mitsubishi Electronics OC376 - page 33

    33 9-1-2. Special Function Operation and Settings (for M-NET Remote Controller) • It is necessary to perform “group settings” and “paired settings” at making group settings of different refrigerant systems (multiple outdoor unit). (A) Group settings: Enter the indoor unit controlled by the remote controller , check the content of entries, ...

  • Mitsubishi Electronics OC376 - page 34

    34 (alternating displa y) "--" will appear in the unit type displa y location when an address has been cleared normally . "88" will appear in the unit type displa y location when an abnor mality has occurred during clear ing. (2) Address check: Refer to section (1) regarding address entry . a) In making group settings: • T urn ...

  • Mitsubishi Electronics OC376 - page 35

    35 9-1-3. Countermeasures for Error During T est Run • If a problem occurs during test run, a code number will appear in the temperature display area on the remote controller (or LED on the outdoor unit), and the air conditioning system will automatically cease operating. Determine the nature of the abnormality and apply corrective measures. Chec ...

  • Mitsubishi Electronics OC376 - page 36

    36 Display Abnormal point and detecting method Causes Check points 1102 1300 1302 1500 High discharging temperature Abnormal if discharge temperature thermistor (TH4) exceeds 125 : or 110 : continuously for 5 minutes. Abnormal if pressure detected by high pressure sensor and converted to saturation temperature exceeds 40 : during defrosting and dis ...

  • Mitsubishi Electronics OC376 - page 37

    37 Display Abnormal point and detecting method Causes Check points Refrigerant shortage When the conditions of below detecting mode 1 or 2 are satisfied during the compressor operation. <Detecting mode 1 > When the below conditions are satisfied completely. 1. Compressor is operating in HEAT mode. 2. Discharge super heat is 80 ; or more. 3. D ...

  • Mitsubishi Electronics OC376 - page 38

    38 Display Abnormal point and detecting method Causes Check points 2502 (Drain sensor model) Drain pump (DP) 1 Let drain sensor self-heated, and if temperature rises slightly, as suspensive abnormality operation stops and changes to protect mode of restarting in 3 minutes. 2 Drain pump is abnormal if the condition above is detected during suspensiv ...

  • Mitsubishi Electronics OC376 - page 39

    39 Display Abnormal point and detecting method Causes Check points 2502 (Float switch model) 2503 4100 1 Check if drain-up machine works. 2 Check drain function. 3 Check moving part of float switch. 4 Check the value of resistance with the float switch ON/OFF. 5 Change the indoor controller board. 1 Malfunction of drain pump 2 Defective drain Clogg ...

  • Mitsubishi Electronics OC376 - page 40

    40 on 2 13 4 5 6 7 8 Display Abnormal point and detecting method Causes Check points 4230 4250 4220 Overvoltage or voltage shortage Abnormal if any of followings are detected during compressor operation; • Decrease of DC bus voltage to 310V • Instantaneous decrease of DC bus voltage to 200V. • Increase of DC bus voltage to 400V. • Decrease ...

  • Mitsubishi Electronics OC376 - page 41

    41 5101 Display Abnormal point and detecting method Causes Check points Room temperature thermistor (TH21) When controller detects short (high temp.)/open (low temp.) in thermistor during the operation, the operation stops and the operation changes to protect mode of restarting in 3 minutes. If the thermistor does not recover in 3 minutes, the oper ...

  • Mitsubishi Electronics OC376 - page 42

    42 5102 Liquid pipe temperature thermistor (TH22) When the thermistor detects short/open during the operation, the operation stops and the operation changes to protect mode of restarting in 3 minutes. If the thermistor does not recover in 3 minutes, the operation stops due to detecting abnormality. In this time, <5102> is displayed. Then, if ...

  • Mitsubishi Electronics OC376 - page 43

    43 5103 Gas pipe temperature thermistor (TH23) When the thermistor detects short/open after 3 minutes-continuous thermo ON during cooling or dry operation, the operation stops and the operation changes to protect mode of restarting in 3 minutes. If the thermistor does not recover in 3 minutes, the operation stops due to detecting abnormality. In th ...

  • Mitsubishi Electronics OC376 - page 44

    44 5106 Outdoor temperature thermistor (TH7) Display Abnormal point and detecting method Causes Check points 1) Connector (TH7) contact failure Check whether the connector (TH7) in the multi controller board is connected or not. When controller detects short/open in thermistor during the operation, the outdoor unit stops once and restarts operation ...

  • Mitsubishi Electronics OC376 - page 45

    45 5201 Display Abnormal point and detecting method Causes Check points Pressure sensor (63HS) When detected pressure in high-pressure sensor is 1 MPa or less during the operation, the compressor stops and restarts operation in 3 minutes. 1) High-pressure sensor failure Check the high-pressure sensor. When the detected pressure is 1 MPa or less at ...

  • Mitsubishi Electronics OC376 - page 46

    46 6603 Transmission bus busy error Over error by collision 1) The transmission processor cannot be transmitted since a short cycle voltage of the noise etc. mixes on the transmission line consecutively. Check whether the transmission line of the indoor unit, fresh master, lossnay and remote controller is connected to the outdoor unit terminal boar ...

  • Mitsubishi Electronics OC376 - page 47

    47 6607 No ACK (Acknowledgement) Abnormality which controller of the sending side detects when there is no answer (ACK) from other side though data was transmitted once. It is detected 6 times every 30 seconds continuously. Factor that not related to origin Turn off power supply of outdoor unit, indoor unit fresh master and lossnay for 2 minutes or ...

  • Mitsubishi Electronics OC376 - page 48

    48 3) When the cause of displayed address and attribute is on the remote controller side 1) When operating with multi refrigerant system indoor units, the indoor units transmits the signal to the remote controller after the other refrigerant system outdoor unit is turned off or turned on again in 2 minutes, and detects abnormality. (The indoor unit ...

  • Mitsubishi Electronics OC376 - page 49

    49 2) When synchronized operation with lossnay in o ther refrigerant system, the indoor units transmit the signal to the lossnay after the lossnay and same refrigerant system outdoor unit are turned off or turned on again in 2 minutes, and detects abnormality. 3) Contact failure of lossnay or indoor unit transmission cable. 4) Indoor unit transmiss ...

  • Mitsubishi Electronics OC376 - page 50

    50 6831 6834 6832 6833 Signal reception(Remote controller) Following symptoms are regarded as abnormality. 1) When the remote controller cannot receive the signal from indoor controller normally even once for 3 minutes 2) When the remote controller cannot receive the signal even once for 2 minutes Signal transmission(Remote controller) Following sy ...

  • Mitsubishi Electronics OC376 - page 51

    51 7105 Address setting error Address setting of the outdoor unit is wrong. Addresses wrong setting of the outdoor unit. Check the address setting of the outdoor unit. The address should be set in 000 or 51-100. The outdoor unit is not set in 000 or in the range of 51-100. When the setting is out of the range, reset it, turn off power supply of the ...

  • Mitsubishi Electronics OC376 - page 52

    52 Transmission data from remote controller Transmission data on transmission path When the number of data errors is "02": · MA remote controller is equipped with the diagnosis function If the air conditioner cannot be operated from the remote controller, diagnose the remote controller as explained below. 1 First, check that the power-on ...

  • Mitsubishi Electronics OC376 - page 53

    53 ON/OFF CENTRALLY CONTROLLED ERROR CODE CLOCK ON OFF ˚C CHECK CHECK MODE FILTER TEST RUN FUNCTION ˚C 1Hr. NOT AVAILABLE STAND BY DEFROST FILTER CHECK TEST TEMP. TIMER SET “ ” indicator: Appears when current is carried. (M-NET Remote controller) (1) For M-NET remote controller systems Symptom or inspection code Cause Inspection method and so ...

  • Mitsubishi Electronics OC376 - page 54

    54 Symptom Display of remote controller CAUSE Even the cooling (heating) operation selection button is pressed, the indoor unit cannot be operated. The auto vane runs freely . Fan setting changes during heating. Fan stops during heating operation. Fan does not stop while operation has been stopped. No setting of fan while start SW has been turned o ...

  • Mitsubishi Electronics OC376 - page 55

    55 Outdoor unit Switch SWU1 1st digit SWU2 2nd digit SW1 Digital Display Switching SW2 Function Switching SW5 Function switching SW3 T rial operation SW4 Model Switching Step Operation in Each Switch Setting ON OFF When to Set Remarks Before turning the power on Before the power is turned on. Rotary switch 1 2 3 4 5 6 1 2 1 2 3 4 5 6 7 8 Function 1 ...

  • Mitsubishi Electronics OC376 - page 56

    56 <Initial Setting> 1 ON OFF 2 34 567 8 <Initial Setting> <Initial Setting> 1 ON OFF 23 4 5 6 1 ON OFF 2 Outdoor unit Switch SW6 function switching SW7 function switching SW8 function switching Step Operation in Each Switch Setting ON OFF When to Set Remarks Before turning the power on. Before turning the power on. During compres ...

  • Mitsubishi Electronics OC376 - page 57

    57 9-6. OUTDOOR UNIT INPUT/OUTPUT CONNECTOR ● State (CN51) ● Auto change over (CN3N) ● Silent Mode / Demand Control (CN3D) CN51 X 5 4 3 A C D 5 E 1 1 3 B G Y L 1 : Error display lamp L 2 : Compressor operation lamp X, Y : Relay (Coil standard of 0.9W or less for DC 12V) F A C D E B G F CN3N X Y SW1 SW2 1 2 3 X, Y : Relay (DC1mA) SW1 SW2 ON He ...

  • Mitsubishi Electronics OC376 - page 58

    58 Parts name Check points Disconnect the connector then measure the resistance with a tester . (At the ambient temperature 10 : ~30 : ) Thermistor (TH3) <Outdoor pipe> Thermistor (TH4) <Discharge> Thermistor (TH6) < Low pressure saturated temperature> Thermistor (TH7) <Outdoor> Thermistor (TH8) <Heatsink> Normal 160k ...

  • Mitsubishi Electronics OC376 - page 59

    59 Notes · High voltage is applied to the connecter (CNF1, 2) for the fan motor . Give attention to the service. · Do not pull out the connector (CNF1, 2) for the motor with the power supply on. (It causes trouble of the outdoor controller circuit board and fan motor .) Self check Symptom : The outdoor fan cannot turn around. Power supply check(R ...

  • Mitsubishi Electronics OC376 - page 60

    60 9-8. HOW TO CHECK THE COMPONENTS <Thermistor feature chart> Low temperature thermistors • Thermistor <Outdoor pipe> (TH3) • Thermistor <Low pressure saturated temperature> (TH6) • Thermistor <Outdoor> (TH7) Thermistor R0 = 15k ' ±3 % B constant = 3480 ± 2% R t =15exp{3480( 273+t – 273 )} 0 : 15k ' 10 : ...

  • Mitsubishi Electronics OC376 - page 61

    61 9-9. TEST POINT DIAGRAM Outdoor multi controller board PUMY -P100VHM PUMY -P125VHM PUMY -P140VHM PUMY -P100VHMA PUMY -P125VHMA PUMY -P140VHMA SW2 Pump down 21S4 4-way valve SV1 Bypass valve CNAC Power supply for multi controller board CNS1 Indoor/ outdoor unit connecting wire CN52 T ransmission wire of centralized control CN40,CN41 Centralized c ...

  • Mitsubishi Electronics OC376 - page 62

    62 Outdoor power circuit board PUMY -P100VHM PUMY -P125VHM PUMY -P140VHM PUMY -P100VHMA PUMY -P125VHMA PUMY -P140VHMA T ABU/V/W Connect to the compressor (MC) V oltage among phases:10V~180V AC T ABP1/SC-P1 Connect to 52C T ABP2/SC-P2 Connect to the ACTM(P) CN4 Connect to the outdoor controller circuit board (CN4) CN2 Connect to the outdoor controll ...

  • Mitsubishi Electronics OC376 - page 63

    63 CNAC2 220-240V AC (Connect to the outdoor controller circuit board (CNAC)) EI Connect to the earth LI, NI V oltage of 220-240V AC is input (Connect to the terminal block(TB1)) CN5 Primary current (Connect to the outdoor power circuit board (CN5)) LO, NO V oltage of 220-240V AC is output (Connect to the outdoor power circuit board) T ABS T ABT CN ...

  • Mitsubishi Electronics OC376 - page 64

    64 Outdoor noise filter circuit board PUMY -P100VHMA PUMY -P125VHMA PUMY -P140VHMA CNAC2 220-240V AC (Connect to the outdoor controller circuit board (CNAC)) EI Connect to the earth LI, NI V oltage of 220-240V AC is input (Connect to the terminal block(TB1)) CN5 52C driving sig- nal (Connect to the outdoor controller circuit board(CNL VB)) LO, NO V ...

  • Mitsubishi Electronics OC376 - page 65

    65 T ransmission power board PUMY -P100VHM PUMY -P125VHM PUMY -P140VHM PUMY -P100VHMA PUMY -P125VHMA PUMY -P140VHMA CN2 Connect to the outdoor multi controller board 1 - 2 : 24–30V DC 3 - 4 : 24–30V DC CN1 Connect to the outdoor noise filter circuit board 1 – 3 : 220–240V AC OC376B--3.qxp 08.1.17 1:16 PM Page 65 ...

  • Mitsubishi Electronics OC376 - page 66

    66 Active filter module PUMY -P100VHM PUMY -P125VHM PUMY -P140VHM L1, L2 Connect to the DCL(Reactor) Connect to the 52C Connect to the outdoor power circuit board(T ABN1) + – I Not used N2 Connect to the outdoor power circuit board(T ABN2) N1 Non-connect P Connect to the out- door power circuit board(T ABP2) DCL L1 L2 ACTM P I N1 N2 (+) (- ) Load ...

  • Mitsubishi Electronics OC376 - page 67

    67 Active filter module PUMY -P100VHMA PUMY -P125VHMA PUMY -P140VHMA + – + DCL L1 L2 ACTM P Io N1 N2 (+) (- ) Load Connection and internal circuit diagram L1, L2 Connect to the DCL(Reactor) Connect to the outdoor power circuit board(T ABP1) N2 Non-connect N1 Non-connect P Connect to the outdoor power circuit board(T ABP2) Connect to the outdoor p ...

  • Mitsubishi Electronics OC376 - page 68

    68 9-10. OUTDOOR UNIT FUNCTIONS SW:setting 0....OFF 1....ON 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 SW1 setting 12345678 00000000 10000000 01000000 1 1000000 00100000 10100000 01 100000 1 1 100000 00010000 10010000 01010000 1 1010000 001 10000 101 10000 01 1 10000 1 1 1 10000 00001000 10001000 01001000 1 1 ...

  • Mitsubishi Electronics OC376 - page 69

    69 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 SW1 setting 12345678 1111 1000 00000100 10000100 01000100 1 1000100 00100100 10100100 01 100100 1 1 100100 00010100 10010100 01010100 1 1010100 001 10100 101 10100 01 1 10100 1 1 1 10100 00001 100 IC1 operation mode IC2 operation mode IC3 operation mode IC4 operation mode IC5 operati ...

  • Mitsubishi Electronics OC376 - page 70

    70 64 65 66 69 70 71 72 73 74 75 76 77 78 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 SW1 setting 12345678 00000010 10000010 01000010 10100010 01 100010 1 1 100010 00010010 10010010 01010010 1 1010010 001 10010 101 10010 01 1 10010 00001010 10001010 01001010 1 1001010 00101010 10101010 01 101010 1 1 101010 0001 1010 1001 1010 0101 1010 1 101 ...

  • Mitsubishi Electronics OC376 - page 71

    71 Display of target subcool step data Displa y of indoor SC/SH data Display of discharge superheat data Displa y of all control target data Displa y of detection data from high-pressure sensor and each thermistor Displa y of actual frequency at time of abnor mality dela y Displa y of fan step number at time of abnormality delay Displa y of opening ...

  • Mitsubishi Electronics OC376 - page 72

    72 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 SW1 setting 12345678 00010001 10010001 01010001 1 1010001 001 10001 101 10001 01 1 10001 1 1 1 10001 00001001 10001001 01001001 1 1001001 00101001 10101001 01 101001 1 1 101001 0001 1001 1001 1001 0101 1001 1 101 1001 001 1 1001 101 1 1001 ...

  • Mitsubishi Electronics OC376 - page 73

    73 170 171 172 173 174 175 176 177 178 179 180 189 192 193 195 196 197 198 199 200 201 202 203 204 206 207 208 209 210 SW1 setting 12345678 01010101 1 1010101 001 10101 101 10101 01 1 10101 1 1 1 10101 00001 101 10001 101 01001 101 1 1001 101 00101 101 101 1 1 101 0000001 1 1000001 1 1 100001 1 0010001 1 1010001 1 01 10001 1 1 1 10001 1 0001001 1 1 ...

  • Mitsubishi Electronics OC376 - page 74

    74 21 1 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 SW1 setting 12345678 1 100101 1 0010101 1 1010101 1 01 10101 1 1 1 10101 1 0001 101 1 1001 101 1 0101 101 1 1 101 101 1 001 1 101 1 101 1 101 1 01 1 1 101 1 11111 0 11 000001 1 1 100001 1 1 010001 1 1 1 ...

  • Mitsubishi Electronics OC376 - page 75

    75 10 ELECTRICAL WIRING 10-1. OVERVIEW OF POWER WIRING 10-2. WIRE DIAMETER AND MAIN POWER SWITCH CAP ACITY 10-2-1. Wiring diagram for main power supply 10-2-2. Power supply wire diameter and capacity This chapter provides an introduction to electrical wiring for the CITY MUL TI-S series, including notes concerning power wiring, wiring for control ( ...

  • Mitsubishi Electronics OC376 - page 76

    76 10-3. DESIGN FOR CONTROL WIRING Please note that the types and numbers of control wires needed by the CITY MUL TI-S series will depend on the remote controllers and whether they are linked with the system. 10-3-1. Selection number of control wires 10-3-3. M-NET Remote controller wiring 10-3-2. Control signal wires Use Remote controller ➔ indoo ...

  • Mitsubishi Electronics OC376 - page 77

    77 (3) Method of obtaining system power factor Use the following formula and the total power and current obtained in parts 1 and 2 on the previous page to calculate the system power factor . System power factor = (T otal system power consumption) (T otal system current x voltage) o 100% 10-6-2. Applying to an electric power company for power and to ...

  • Mitsubishi Electronics OC376 - page 78

    78 11 REFRIGERANT PIPING T ASKS Line-Branch Method Connection Examples (Connecting to Four Indoor Units) Liquid Line Gas Line Piping Diameter (mm) Model PUMY -P100-140 Liquid Line (mm) Gas Line (mm) { 15.88 { 9.52 Liquid Line Gas Line Liquid Line Gas Line Piping Diameter (mm) Model number 50 or lower 63 to 140 { 6.35 { 12.7 { 9.52 { 15.88 Outdoor U ...

  • Mitsubishi Electronics OC376 - page 79

    79 Header-Branch Method Connection Examples (Connecting to Four Indoor Units) Liquid Line Gas Line Piping Diameter (mm) Model { 9.52 { 15.88 Liquid Line Gas Line Liquid Line Gas Line Piping Diameter (mm) Model number 50 or lower 63 to 140 { 6.35 { 12.7 { 9.52 { 15.88 Outdoor Unit First Branch Indoor unit CAP A B C D A+a+b+c+d+e+f [ 120m A+f [ 80m f ...

  • Mitsubishi Electronics OC376 - page 80

    80 Method of Combined Branching of Lines and Headers Connection Examples (Connecting to Five Indoor Units) Outdoor unit First branching (branching joint) Branching joint Indoor unit Branching header T o downstream unit Blind caps A B C D E F G A+B+C+a+b+c+d+e is 120 meters or less A+B+b is 80 meters or less B+b is 30 meters or less 30 meters or les ...

  • Mitsubishi Electronics OC376 - page 81

    81 Indoor unit The smallest room The second smallest room Outdoor unit V entilation apparatus Indoor unit Opening W all Outdoor unit (Situation in which there are no door openings or in which there are open- ings above and blow doors that occupy at least 0.15% of the floor area) Indoor unit Outdoor unit 1 1-2. PRECAUTIONS AGAINST REFRIGERANT LEAKAG ...

  • Mitsubishi Electronics OC376 - page 82

    82 12 DISASSEMBL Y PROCEDURE OPERA TING PROCEDURE PHOTOS & ILLUSTRA TION 1. Removing the service panel and top panel (1) Remove 3 service panel fixing screws (5 ✕ 10) and slide the hook on the right downward to remove the service panel. (2) Remove screws (3 for front, 3 for rear/5 ✕ 10) of the top panel and remove it. Figure 1 T op panel fi ...

  • Mitsubishi Electronics OC376 - page 83

    83 OPERA TING PROCEDURE PHOTOS & ILLUSTRA TION Photo 4 (6) Remove electrical parts box fixing screw (4 ✕ 10) and detach the electrical parts box by pulling it upward. The electrical parts box is fixed with 2 hooks on the left and 1 hook on the right. Electrical parts box Electrical parts box fixing screw From the previous page. Photo 5 4. Rem ...

  • Mitsubishi Electronics OC376 - page 84

    84 4-way valve coil (21S4) 7. Removing the 4-way valve coil (21S4) (1) Remove the service panel. (See figure 1.) (2) Remove the top panel. (See figure 1.) [Removing the 4-way val ve c oi l] (3) Remove 4-way valve coil fixing screw (M4 ✕ 6). (4) Remove the 4-way valve coil by sliding the coil toward you. (5) Disconnect the connector 21S4 (green) o ...

  • Mitsubishi Electronics OC376 - page 85

    85 OPERA TING PROCEDURE PHOTOS 9. Removing bypass valve coil (SV1) and bypass valve (1) Remove the service panel. (See figure 1.) (2) Remove the top panel. (See figure 1.) (3) Remove 3 right side panel fixing screws (5 ✕ 10) in the rear of the unit and remove the right side panel. (4) Remove the bypass valve coil fixing screw (M4 ✕ 6). (5) Remo ...

  • Mitsubishi Electronics OC376 - page 86

    86 Accumulator OPERA TING PROCEDURE PHOTOS 12. Removing the compressor (MC) (1) Remove the service panel. (See figure 1.) (2) Remove the top panel. (See figure 1.) (3) Remove 2 front cover panel fixing screws (5 ✕ 10) and remove the front cover panel. (See photo 3.) (4) Remove 2 back cover panel fixing screws (5 ✕ 10) and remove the back cover ...

  • Mitsubishi Electronics OC376 - page 87

    87 13-1. STRUCTURAL P ARTS PUMY -P125VHM 1 2 3 45 6 7 89 10 11 9 12 15 13 14 16 17 Part No. Part Name Specification No. Wiring Diagram Symbol Recom- mended Q'ty PUMY -P125VHM Remarks (Drawing No.) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 38 1 2 1 1 1 1 1 2 1 1 1 1 1 1 1 1 (DG12F536H10) (BK00C143G80) (BK00C142G15) (DG79R130H01) – T7W E02 662 ...

  • Mitsubishi Electronics OC376 - page 88

    88 26 25 27 30 29 28 21 24 23 22 1 2 3 10 11 12 13 14 15 16 17 18 19 20 18 4 7 8 9 5 6 13-2. FUNCTIONAL P ARTS PUMY -P125VHM OC376B--3.qxp 08.1.17 1:16 PM Page 88 ...

  • Mitsubishi Electronics OC376 - page 89

    89 Part numbers that are circled are not shown in the figure. Part No. Part Name Specification No. Wiring Diagram Symbol Recom- mended Q , ty Remarks (Drawing No.) Q , ty/set 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 2 R01 E44 2 ...

  • Mitsubishi Electronics OC376 - page 90

    90 26 25 27 30 29 28 21 24 23 22 1 2 3 10 11 12 13 14 15 16 17 18 19 20 18 4 7 8 9 5 6 14-1. FUNCTIONAL P ARTS PUMY -P100VHM PUMY -P125VHM PUMY -P140VHM 14 RoHS P ARTS LIST OC376B--3.qxp 08.1.17 1:16 PM Page 90 ...

  • Mitsubishi Electronics OC376 - page 91

    91 Part numbers that are circled are not shown in the figure. Part No. Part Name Specification No. Wiring Diagram Symbol Recom- mended Q'ty Remarks (Drawing No.) Q'ty/set 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 RoHS G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G ...

  • Mitsubishi Electronics OC376 - page 92

    92 26 25 27 29 28 21 24 23 22 1 2 3 10 11 12 13 14 15 16 17 18 19 20 4 7 8 9 5 6 18 FUNCTIONAL P ARTS PUMY -P100VHMA PUMY -P125VHMA PUMY -P140VHMA OC376B--4.qxp 08.1.17 1:17 PM Page 92 ...

  • Mitsubishi Electronics OC376 - page 93

    93 Part No. Part Name Specification No. RoHS Wining Diagram Symbol Recom- mended Q'ty Remarks (Drawing No.) Q'ty/set 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 2 T ...

  • Mitsubishi Electronics OC376 - page 94

    94 14-2. STRUCTURAL P ARTS PUMY -P100VHM PUMY -P125VHM PUMY -P140VHM PUMY -P100VHMA PUMY -P125VHMA PUMY -P140VHMA 1 2 3 45 6 7 89 10 11 9 12 15 13 14 16 17 Part No. Part Name Specification No. Wiring Diagram Symbol Recom- mended Q'ty PUMY -P100,125,140VHM PUMY -P100,125,140VHMA Remarks (Drawing No.) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Ro ...

  • Mitsubishi Electronics OC376 - page 95

    95 15 OPTIONAL P ARTS CMY -Y62-G-E CMY -Y64-G-E NUMBER OF BRANCHING POINTS 2 4 CMY -Y68-G-E 8 BRANCH PIPE (Joint) Part No. DRAIN SOCKET Part No. P AC-SG61DS-E AIR OUTLET GUIDE Part No. P AC-SG59SG-E DRAIN P AN Part No. P AC-SG64DP-E w Need 2 pieces. FIL TER DR YER (For liquid line : [ [ 9.52) Part No. P AC-SG82DR-E w Only for R410A model (Don’t u ...

  • Mitsubishi Electronics OC376 - page 96

    HEAD OFFICE : TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO100-8310, JAP AN c Copyright 2006 MITSUBISHI ELECTRIC ENGINEERING CO., L TD. Distributed in Jan. 2008 No. OC376 REVISED EDITION-B PDF 9 Distributed in Aug. 2006 No. OC376 REVISED EDITION-A PDF 8 Distributed in Mar . 2006 No. OC376 PDF 9 Made in Japan New publication, effective Jan. 2008 ...

Manufacturer Mitsubishi Electronics Category Noise Reduction Machine

Documents that we receive from a manufacturer of a Mitsubishi Electronics OC376 can be divided into several groups. They are, among others:
- Mitsubishi Electronics technical drawings
- OC376 manuals
- Mitsubishi Electronics product data sheets
- information booklets
- or energy labels Mitsubishi Electronics OC376
All of them are important, but the most important information from the point of view of use of the device are in the user manual Mitsubishi Electronics OC376.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Mitsubishi Electronics OC376, service manual, brief instructions and user manuals Mitsubishi Electronics OC376. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Mitsubishi Electronics OC376.

A complete manual for the device Mitsubishi Electronics OC376, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Mitsubishi Electronics OC376 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Mitsubishi Electronics OC376.

A complete Mitsubishi Electronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Mitsubishi Electronics OC376 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Mitsubishi Electronics OC376, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Mitsubishi Electronics OC376, that we can find in the current document
3. Tips how to use the basic functions of the device Mitsubishi Electronics OC376 - which should help us in our first steps of using Mitsubishi Electronics OC376
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Mitsubishi Electronics OC376
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Mitsubishi Electronics OC376 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Mitsubishi Electronics OC376?

Use the form below

If you did not solve your problem by using a manual Mitsubishi Electronics OC376, ask a question using the form below. If a user had a similar problem with Mitsubishi Electronics OC376 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)