-
Texas Instruments 3000 - page 1
T EXAS I NSTRUMENTS TravelMate 3000 Notebook Computer User ’ s Manual ...
-
Texas Instruments 3000 - page 2
Contents Preface .......................................................................................................................... v 1 Taking a First Look Learning About Hardware ........................................................................................................ 1-2 Learning About Options .............................. ...
-
Texas Instruments 3000 - page 3
Contents 6 TravelMate 3000 Options Numeric Keypad ........................................................................................................ 6-2 RAM Modules ........................................................................................................... 6-3 Internal Modem .................................................... ...
-
Texas Instruments 3000 - page 4
Copyright 1991 Texas Instruments Incorporated All Rights Reserved - Printed in U.S.A TravelMate 3000 Notebook Computer User's Manual Part No. 2566946-0001 Original Issue: October 1990 Revision C: September 1991 Changes may be made periodically to the information in this publication. Such changes will be incorporated in new editions of ...
-
Texas Instruments 3000 - page 5
Preface Your new Texas Instruments TravelMate TM 3000 Notebook Computer is a lightweight, full-function computer with the features and power of many desktop personal computers. The TravelMate 3000 has a standard 20-megabyte (MB) or optional 40-MB internal hard disk drive, an 80386 TM SX microprocessor, factory-installed MS-DOS ® version 4.01. Seve ...
-
Texas Instruments 3000 - page 6
Preface Unpacking When you open the container in which your computer is packed, you should find the following items: q TravelMate 3000 Notebook Computer q AC Adapter and detachable wall receptacle cord q Two tilt legs that insert into the bottom rear corners of the unit to increase the keyboard angle q This user's manual and the MS-DOS User’ ...
-
Texas Instruments 3000 - page 7
Preface italics Used to denote Setup Program items and settings, key words, and references to other publications Monospace Used for prompts an d menus that display during operation of your computer, including prompts (text generated by the computer) and entries you are supposed to type on the keyboard Bold Used for keys, key sequences, and drive de ...
-
Texas Instruments 3000 - page 8
Preface Keyboard keys are listed several ways in this manual, depending on the number of keys you must press to produce a character or function. For example, some key fronts on the keyboard are labeled with blue to indicate their use only in conjunction with the Fn key. The text refers to these keys according to their function, preceded by the addi ...
-
Texas Instruments 3000 - page 9
Preface Chapter 5 - Installing and Using Application Programs briefly describes guidelines for installing your own application programs plus some of the software installed at the factory in your TravelMate 3000, including the BatteryPro, Laptop Manager, and password utilities. Chapter 6 - TravelMate 3000 Options describes several options that can e ...
-
Texas Instruments 3000 - page 10
Preface Appendix G - Connector Pin Assignments lists the signals produced by the connectors provided on the TravelMate 3000. Appendix H - Screen Standards lists the characteristics of the various display adapters supported by the TravelMate 3000. A Glossary of frequently used technical terms and an Index are included near the back of the manual to ...
-
Texas Instruments 3000 - page 11
1 Taking A First Look This chapter tells you about: q Computer hardware such as th e main circuit board, the display, and the keyboard q Hardware options available for your TravelMate 3000 Notebook Computer q Software operating systems and application programs Contents Learning About Hardware ........................................................ ...
-
Texas Instruments 3000 - page 12
Learning About Hardware The standard Texas Instruments TravelMate 3000 Notebook Computer looks like this when it is closed. The standard TravelMate 3000 looks like this when it is set up and ready to operate. If you are already familiar with the main components of a computer, you may want to skim the remainder of this chapter and skip ahead to Chap ...
-
Texas Instruments 3000 - page 13
Learning About Hardware The TravelMate 3000's standard hardware consists of a system circuit board, a keyboard, an LCD (liquid crystal display) screen, a hard disk drive, a 3.5-inch floppy diskette drive, serial and parallel I/O (input/output) ports, mouse port, and other electronic circuits needed to control the display and external options. ...
-
Texas Instruments 3000 - page 14
Learning About Hardware RAM RAM (random access memory) stores data and application software for the processor. You can write to or read from RAM freely, but once the power is turned off, the data in RAM is lost. RAM size is described by the amount of information (bytes) it can store. Symbols often used for this are "K" and "M". ...
-
Texas Instruments 3000 - page 15
Learning About Hardware The TravelMate 3000's LCD screen can be set to emulate industry-standard display modes, including the VGA (video graphics array) mode used by IBM in its latest PS/2 TM series of personal computers. The screen displays colors as various shades of gray. The illuminated, triple supertwist, LCD screen gives you maximum read ...
-
Texas Instruments 3000 - page 16
Learning About Hardware Hard Disk Formatting The hard disk consists of a platter that is divided into cylinders. A cylinder is a collection of tracks in the same position on different sides of the hard disk platters. The tracks of each cylinder are further divided into sectors. Each sector is numbered and holds 512 bytes of data. The computer locat ...
-
Texas Instruments 3000 - page 17
Learning About Option You can enhance the performance of a standard TravelMate 3000 with the addition of hardware options available from Texas Instruments. These options enable you to send and receive data over telephone lines, increase memory, enter numeric data more easily, and add several other features. The following hardware options are availa ...
-
Texas Instruments 3000 - page 18
Learning About Options Numeric Keypad The Numeric Keypad option (TI Part No. 2568033-0001) connects to the right side of the TravelMate 3000 case, enabling you to more easily type numeric data. The Numeric Keypad layout is similar to the keypad on a full-sized IBM enhanced AT TM keyboard. Extra Internal Battery Pack With an extra internal battery p ...
-
Texas Instruments 3000 - page 19
Learning About Options Printers Texas Instruments makes a variety of laser and impact printers you can use with the TravelMate 3000, enabling you to a produce hard copy of information you have created. You can connect almost any parallel printer to the TravelMate 3000 parallel printer port or serial printer to the serial port. External Monitors You ...
-
Texas Instruments 3000 - page 20
Learning About Software A computer system needs software before it can carry out any useful task. Without software, your computer is just a Collection of electrical components. In order to use computer hardware for tasks like writing memos or balancing a checking account, software is necessary. Software is a series of instructions that direct the c ...
-
Texas Instruments 3000 - page 21
2 Learning About Your Computer This chapter tells you about: q The Texas Instru ments TravelMate 3000 Notebook Computer LCD screen and how to adjust it q Ports and connectors on the side panels of the computer case q The keyboard and common key assignments q The status indicator lights and their meaning Contents LCD Screen 2-3 Resolution .......... ...
-
Texas Instruments 3000 - page 22
Contents Keyboard Keys .................................................................................................. 2-10 Color Coded Keys ....................................................................................... 2-10 Function Keys ............................................................................................ 2-10 E ...
-
Texas Instruments 3000 - page 23
LCD Screen Your Texas Instruments TravelMate 3000 Notebook Computer displays text and graphics on a triple supertwist, illuminated, liquid crystal display (LCD) with cold cathode fluorescent tube (CCFT) backlight, giving true black-on-white contrast. The TravelMate 3000 is able to emulate IBM's video graphics array (VGA) by displaying colors a ...
-
Texas Instruments 3000 - page 24
LCD Screen Screen Controls The LCD screen is illuminated to enable you to control background brightness and contrast for better readability. The backlight turns on automatically when you turn on the computer. Note: To conserve battery power and prolong screen life, you can set the backlight to turn off automatically if you do not use the keyboard f ...
-
Texas Instruments 3000 - page 25
LCD Screen Standard/Reverse Switch The screen normally displays black characters on a white background. You can reverse this image to white on black by setting the standard/reverse switch to the q (reverse) position. Some graphic images may display like a photographic negative on the LCD screen. Reversing the image should correct this effect. Learn ...
-
Texas Instruments 3000 - page 26
Connectors and Ports Caution: Turn off the computer before connecting any external devices to the computer's connectors. Right Side Panel The right side panel of the computer contains the numeric keypad connector to connect the optional Numeric Keypad to your computer. A dust cap is provided for the numeric keypad connector. Remove and store t ...
-
Texas Instruments 3000 - page 27
Connectors and Ports Parallel (Printer) Port You can connect a parallel printer or other device that uses a standard parallel interface to this 25-pin female connector. The cable from the printer or other device must terminate in a 25-pin IBM-PC-style male connector to connect to this port. Pin assignments for this connector are listed in Appendix ...
-
Texas Instruments 3000 - page 28
Connectors and Ports RearPanel The rear panel of the computer has the expansion bus connector and the AC Adapter jack. AC Adapter Jack The AC Adapter mini-DIN jack connects to this jack to recharge the battery and supply ac power to the computer. See Chapter 3 for instructions on charging and conditioning the internal battery pack. Caution: Use onl ...
-
Texas Instruments 3000 - page 29
Connectors and Ports Bottom Panel The bottom panel of the computer provides access to remove and install the supplied internal battery pack. See Chapter 3 for battery pack removal and installation instructions. Tilt Legs - In the rear corners of the bottom panel are two holes into which you can insert the furnished tilt legs to increase the angle o ...
-
Texas Instruments 3000 - page 30
Keyboard Keys The TravelMate 3000 keyboard provides all the functions of the IBM AT-101 -style enhanced keyboard. Many keys on the keyboard are similar to those on a standard typewriter, but you may not be familiar with some keys. The following sections describe special function keys not found on a standard typewriter. Note: MS-DOS and application ...
-
Texas Instruments 3000 - page 31
Keyboard Keys The function keys perform editing functions in MS-DOS (see the MS-DOS User's Manual supplied with your computer). Applications programs use the function keys for various purposes; see your application program documentation. Note: Above the function keys is a slot to hold the furnished blank template where you can write the specif ...
-
Texas Instruments 3000 - page 32
Keyboard Keys Backspace With most applications the ← (Backspace) key moves the cursor to the left one space at a time, erasing any character it passes. Ctrl The keyboard has two identical Ctrl (Control) keys. With many applications the Ctrl key changes the function of another key when both keys are pressed simultaneously. For example, under MS-DO ...
-
Texas Instruments 3000 - page 33
Keyboard Keys Note: You must first run the MS-DOS utility, GRAPHICS.COM, to print graphic displays; if not, only text characters are printed. See your MS-DOS User's Manual for details. You can press the Ctrl-PrtSc keys to toggle on the "echo" function, during which your printer prints the currently displayed line of data each time yo ...
-
Texas Instruments 3000 - page 34
Keyboard Keys Del Press the Del (Delete) key to delete the character at the cursor. In MS-DOS and many applications, characters on the line to the right of the cursor are pulled to the left. Using the NumLk Key and the Embedded Numeric Keypad Your TravelMate 3000 features an embedded keypad (built into the keyboard) that provides the same functions ...
-
Texas Instruments 3000 - page 35
Keyboard Keys The embedded numeric keypad has three modes you can enter by toggling the Fn-F7 (NumLk) keys as signaled by the Num Lock indicator light: off, on, or blinking. The three modes are described below. Num Lock On When the Num Lock indicator light is on, pressing the Fn key with the appropriate keys generates the characters shown in this f ...
-
Texas Instruments 3000 - page 36
Keyboard Keys Num Lock Blinking When the Num Lock indicator light is blinking-caused by pressing the Fn-F7 (NumLk) keys-the embedded numeric keypad becomes a temporary numeric keypad that does not require you to press any other key. This mode is particularly useful when you have to enter a large quantity of numbers. If you press and hold the Fn key ...
-
Texas Instruments 3000 - page 37
Keyboard Keys Break Pressing the Ctrl-Pause (Break) keys sends a Break signal to stop current program execution. Your application program may have other or additional functions for the Break signal. Set Up Pressing the Fn-Esc (Set Up) keys when the computer displays the MS-DOS C:> prompt loads the Setup Program from the hard disk. The Setup Pro ...
-
Texas Instruments 3000 - page 38
Keyboard Keys Turbo Pressing the Fn-F5 (Turbo) keys increases the CPU processing speed to 20 MHz. When the Turbo feature is off, the CPU runs at 8 or 10 MHz. The Turbo feature uses more battery power but provides faster processing. When you turn on the Turbo feature, the Turbo indicator light comes on. You also can change CPU speed using the speed ...
-
Texas Instruments 3000 - page 39
Indicator Lights Above the keyboard are eight indicator lights that show the status of certain operating features. Power The Power indicator glows green when you turn on the Power switch (located above the right side of the keyboard). If the light does not come on, the AC Adapter may not be plugged in or the battery may be discharged. The Power ind ...
-
Texas Instruments 3000 - page 40
Indicator Lights Note: The time variations in the Low Batt indicator functions are affected by the battery charge remaining when you turn on power and may also vary among individual computers. Note: See "Conditioning the Battery Pack- in Chapter 3 for more details on the Power and Low Batt indicators. Turbo The Turbo indicator comes on when th ...
-
Texas Instruments 3000 - page 41
Indicator Lights Num Lock (Numeric Keypad Lock) The Num Lock indicator comes on when you press the Fn-F7 (NumLk) keys to toggle on the numeric keypad lock function. See 'Using the NumLk Key and the Embedded Numeric Keypad" earlier in this chapter for full details. Scroll Lock The Scroll Lock indicator comes on when you press the ScrLk key ...
-
Texas Instruments 3000 - page 42
...
-
Texas Instruments 3000 - page 43
3 Getting Started This chapter tells you about: q Recommended operating and storage environments for your Texas Instruments TravelMate 3000 Notebook Computer q How to take care of the computer's hard disk q Connecting the AC Adapter and installing, removing, and charging the internal battery pack q Starting up your TravelMate 3000 q Using the ...
-
Texas Instruments 3000 - page 44
Contents Using the Floppy Drive ............................................................................................ 3-15 Taking Care of Your Floppies ........................................................................... 3-15 Using Your Floppies ......................................................................................... ...
-
Texas Instruments 3000 - page 45
Guidelines & Precautions Operate your Texas Instruments TravelMate 3000 Notebook Computer according to the following environmental specifications and operating guidelines. Operating Environment When using your computer, always try to ensure that the temperature and humidity of the surroundings fall within the following ranges. Temperature Opera ...
-
Texas Instruments 3000 - page 46
Guidelines & Precautions Taking Care of the Hard Disk The hard disk in your TravelMate 3000 is specially designed to withstand the rigors of travel. The hard disk heads automatically park themselves when the computer is turned off. However, it is still a precision device and careful treatment will prolong its life. Follow these guidelines to ge ...
-
Texas Instruments 3000 - page 47
Guidelines & Precautions q When moving your computer to a location where the temperature is more than 18 ° F (10 ° C) different from the current location, do the move in two stages: (1) First, leave the computer in a place where the temperature is somewhere between that of the new location and the old location for about I hour. (2) Then move ...
-
Texas Instruments 3000 - page 48
Providing Power You can operate your TravelMate 3000 from ac power of the correct voltage via the furnished AC Adapter. You also can run the computer using the internal battery pack installed at the factory. The first time you use the computer or after the computer has been out of service for several weeks, connect the AC Adapter as described below ...
-
Texas Instruments 3000 - page 49
Providing Power Connect the AC Adapter to your TravelMate 3000 as follows. 1. Set the computer's power switch to the off position . 2. Connect the female end of the supplied ac cord to the inlet on the AC Adapter body. 3. Connect the male end of the ac cord into a grounded wall receptacle of the correct voltage. Use a grounded plug adapter if ...
-
Texas Instruments 3000 - page 50
Providing Power q The green indicator comes on when the AC Adapter is connected to both the computer and a wall outlet and the battery is not charging or is not installed in the computer. Note: When the amber light goes off after you have charged the battery pack, wait 10 minutes for the battery pack to cool down to operating temperature before run ...
-
Texas Instruments 3000 - page 51
Handling the Battery Pack Removing the Battery Pack The internal NiCad battery pack and its cover are built as one unit; do not try to separate the cover from the battery pack. Remove the battery pack from the computer as follows. 1 Turn off the computer and disconnect the AC Adapter and any other external device connectors. 2. Close the display an ...
-
Texas Instruments 3000 - page 52
Handling the Battery Pack Installing the Battery Pack Install an internal NiCad battery pack as follows. If the battery is new or not fully charged, condition and/or charge the battery as described later in this chapter. 1. Turn off the computer, disconnect th e AC Adapter and any other external devices, and carefully lay the computer upside down o ...
-
Texas Instruments 3000 - page 53
Handling the Battery Pack Conditioning the Battery Pack An unconditioned battery-one that is brand-new, one installed in a computer that has not been used for a long time, or one that has sat 'on the shelf for several months must be conditioned before it will accept a full charge. Condition and charge the battery pack as follows. 1. Install th ...
-
Texas Instruments 3000 - page 54
Handling the Battery Pack 5. Disconnect the AC Adapter and fully discharge the battery again by using the computer solely on battery power, or use the Battery Watch deep discharge feature. 6. Recharge the battery completely a second time. Your battery is now conditioned and able to achieve a maximum charge. Note: You should always allow up to 11/2 ...
-
Texas Instruments 3000 - page 55
Starting Your Computer Your new TravelMate 3000 Notebook Computer is shipped from the factory with software already installed on the hard disk. The TravelMate 3000 has MS-DOS version 4.01, Laptop Manager, Laptop File Manager, BatteryPro, Battery Watch, RPAL palette utility, and other software programs that make your computer more powerful and easie ...
-
Texas Instruments 3000 - page 56
Restarting the computer You may sometime want to return the system to its startup state without turning off the power. This is called restarting or rebooting the system (sometimes called a warm boot, as opposed to a cold boot, which involves turning the power off and on again). Caution: Any data in main memory (RAM) will be erased when you restart ...
-
Texas Instruments 3000 - page 57
Using the Floppy Drive The TravelMate 3000 floppy drive can read from and write to 3.5-inch, double-sided, high-density (2HD), 1.44 MB floppy diskettes-the equivalent of approximately 800 typed sheets. The floppy drive also can read/write to the lower capacity, 3.5-inch, 720 KB, double-density (2DD) floppies. Before data can be stored on a new flop ...
-
Texas Instruments 3000 - page 58
Using the Floppy Drive Write-Protect Tab - The write-protect tab is used to prevent changes being made inadvertently to important files. To write-protect a floppy, slide the write-protect tab to the open position: to allow the computer to write on the floppy, slide the tab to the closed position. Using Your Floppies Follow these guidelines when han ...
-
Texas Instruments 3000 - page 59
Using the Floppy Drive q If a floppy appears to be damaged, make a copy of it, if you can, and immediately discard the damaged floppy. q Before turning off the computer, always remove a floppy from the floppy drive. Inserting a Floppy Into the Drive Insert a floppy diskette into the TravelMate 3000 floppy drive as follows. 1. Insert the floppy into ...
-
Texas Instruments 3000 - page 60
Help Displays The TravelMate 3000 offers two easily accessed help files that display information to help you use your computer: One file describes MS-DOS commands; the second file describes the productivity software supplied with your computer. Both help files are similar in appearance and both have their own help file (accessed by pressing the PI ...
-
Texas Instruments 3000 - page 61
Help Displays TravelMate 3000 Utilities Description You can view the Utilities Description help file by pressing the F1 key at the Laptop Manager main menu, or by typing at the MS-DOS C:> prompt: HELP and pressing the Enter key. This help file briefly describes most utility programs available under the UTILS directory. See your BatteryPro & ...
-
Texas Instruments 3000 - page 62
4 Customizing Your Computer This chapter tells you about: q How to enter and exit the Setup Program to customize your TravelMate 3000 Notebook Computer q Using the Setup Program to configure the computer for your operating environment Contents Accessing the Setup Program .............................................................................. ...
-
Texas Instruments 3000 - page 63
Contents User Features. Page 2 ............................................................................................... 4-11 Power Savings ................................................................................................... 4-11 Backlight Off ..................................................................................... ...
-
Texas Instruments 3000 - page 64
Accessing the Setup Program You can customize many computer settings so that your Texas Instruments TravelMate 3000 Notebook Computer always powers up with your settings, using either of two Setup Programs to specify hardware and software configurations. The Setup Program factory default settings are satisfactory for most working environments and a ...
-
Texas Instruments 3000 - page 65
Accessing the Setup Program Accessing Setup From an Application You can load the ROM-based Setup Program directly from any application program by pressing the Ctrl-Alt-Esc keys. This method is not recommended unless the computer will not boot otherwise because the computer restarts (reboots) when you exit the Setup Program and erases all data in me ...
-
Texas Instruments 3000 - page 66
Accessing the Setup Program Pressing the F2 (Sys Info) key displays an informational screen listing the computer's firmware version numbers, coprocessor type (if installed), port addresses (in hexadecimal), and option ROM data. (Also refer to the DATES utility described in the BatteryPro & Productivity Software User's Manual for simil ...
-
Texas Instruments 3000 - page 67
System Options, Page 1 When you first load the Setup Program, it displays page I of the three-page Setup Program. Clock The computer has a battery-operated clock that keeps track of the time and date. This category enables you to set or correct the current time and date. Time This item sets the current time. When seconds are high-lighted, pressing ...
-
Texas Instruments 3000 - page 68
System Options, Page 1 Date Display This item enables you to choose either the U.S. 12-hour or European 24-hour time display. Memory The memory category specifies the type and amount of memory and how you want memory allocated in the computer. Standard Memory This item specifies the amount of memory to allocate to the main memory. Select the 640 KB ...
-
Texas Instruments 3000 - page 69
System Options, Page 1 Because the EMM.SYS device driver controls hardware registers to enhance computer performance, other LIM 4.0 drivers should not be used on the computer unless they comply with the specifications found in this chapter. The factory default is 32 KB . Shadow ROM This item selects whether or not to use shadow ROM in the computer. ...
-
Texas Instruments 3000 - page 70
System Options, Page 1 4. Check that the Unused item equals 0 (zero). If not repeat steps 2 and 3 as necessary. Note: Do not exit the Setup Program with the Unused item showing any value except 0. Allocate memory to the other memory item until Unused equals 0; otherwise, the computer will report an error condition the next time you try to start it. ...
-
Texas Instruments 3000 - page 71
System Options, Page 1 Hard Disk Drives The Hard Disk category specifies the built-in hard disk drive and a future external hard disk option. Hard Disk 1 The Hard Disk I category is the built-in hard disk drive. Set this item properly according to your hard disk type. The other items in this category are automatically set with any type except the T ...
-
Texas Instruments 3000 - page 72
User Features, Page 2 Press the Fn- ↓ (PgDn) keys to continue to page 2 of the Setup Program. Page 2 provides power-savings, display control, keyboard-lock, and alarm configuration categories. Power Savings The Power Savings category specifies the delay (or time-out) period of four power-saving functions. Each power-saving delay function occurs a ...
-
Texas Instruments 3000 - page 73
User Features, Page 2 Backlight Off After a selected period of no input from the keyboard, the system automatically shuts off the LCD screen. Pressing any key on the keyboard-preferably the Shift key-turns the LCD on again. The default setting is 2 minutes. Note: If you are using a mouse with your application program, you may want to set the Backli ...
-
Texas Instruments 3000 - page 74
User Features, Page 2 Note: CPU speed always reverts to 8 MHz when the computer accesses the floppy drive. You also can change CPU speed while the computer is running by using the SPEED utility (described in your BatteryPro & Productivity Software User's Manual ) at the MS- DOS prompt. And you can use the speed keys: Ctrl-Alt- ↑ and Ctrl ...
-
Texas Instruments 3000 - page 75
User Features, Page 2 Screen The Screen category enables you to select several operating features for the built-in LCD screen or for an external monitor connected to your TravelMate 3000. The computer automatically powers up using the built-in LCD. Switch to your external monitor by entering ALTVID at the MS-DOS C:> prompt. Caution: Before conn ...
-
Texas Instruments 3000 - page 76
User Features, Page 2 You must select the appropriate monitor device driver to match your external monitor and your application program. Most applications using 640-by-480 resolution do not require a device driver. Applications requiring super VGA (800-by-600) also require an appropriate device driver. See your BatteryPro & Productivity Softwar ...
-
Texas Instruments 3000 - page 77
User Features, Page 2 Scroll Lock This item specifies the power-up state of the ScrLk key. Possible settings are On or Off . The default setting is Off . Repeat Rate This item specifies the key repeat rate-also called the typematic rate-that is, the speed at which a character repeats on the screen when you press and hold down a key. The possible se ...
-
Texas Instruments 3000 - page 78
User Features Page 2 The default setting is Auto Standby . The computer beeps in any case when you close the cover unless you turn off the beeper at the Cover Alarm item described above. Quick Boot This item selects quick loading of the system. When this item is set to On , the system bypasses some of the powerup self checks (including memory check ...
-
Texas Instruments 3000 - page 79
External Communications, Page 3 Press the Fn- ↓ (PgDn) keys to continue to page 3 of the Setup Program. Page 3 provides communication configuration categories. Parallel Port This item assigns the 25-pin parallel port on the left side panel to LPT1 (or disables the port). The default setting is LPT 1. If you are not using the port, set this item t ...
-
Texas Instruments 3000 - page 80
External Communications Page 3 Standard Comm This item assigns the standard nine-pin serial port (sometimes called the SIO for serial input/output) on the left side of the computer case as Port 1 (or disables the port). The default setting is Port 1. The Disable setting conserves battery power. Set the following communication parameters to meet the ...
-
Texas Instruments 3000 - page 81
External Communications, Page 3 DSR (Data Set Ready) The RS-232C data set ready (DSR) signal can be forced on for application programs requiring this signal. Possible settings are Normal and Force On The default setting is Normal . DCD (Data Carrier Detect) The RS-232C data carrier detect (DCD) signal can be forced on for application programs requi ...
-
Texas Instruments 3000 - page 82
5 Installing and Using Application Programs This chapter tells you about q Guidelines for loading IBM AT-comp atible application programs q How to set up and use the furnished Laptop Manager program for your operating environment Contents Guidelines for Installing Applications ........................................................................ ...
-
Texas Instruments 3000 - page 83
Guidelines for Installing Applications Your TravelMate 3000 Notebook Computer is fully compatible with IBM AT computers. AU application programs written to execute on AT computers will execute on the TravelMate 3000, and you can install the programs in much the same way on the TravelMate 3000. However, like most computers, you must consider the cha ...
-
Texas Instruments 3000 - page 84
Guidelines for Installing Applications Keyboard The TravelMate 3000 keyboard emulates all functions of an IBM AT-101 enhanced keyboard. When installing an application program, select the IBM 10 1 or AT-enhanced keyboard configuration. Communication Ports The serial port is Port 1, and the optional Internal Modem, if installed, is Port 2. When insta ...
-
Texas Instruments 3000 - page 85
Guidelines for Installing Application Memory The standard TravelMate 3000 has 2 MB of memory, 640 KB of system memory plus 1280 KB Extended/Expanded memory. You can add 2 or 4 MB of additional optional memory to your TravelMate 3000 that can be configured either as Extended memory or LIM EMS (expanded) memory. See Appendix F for details on these tw ...
-
Texas Instruments 3000 - page 86
Guidelines for Installing Applications Default AUTOEXEC.BAT File Each line of the TravelMate 3000 AUTOEXEC.BAT file and its purpose are defined in the table following the Me listing. Take special note of those lines relating to Laptop Manager. @ECHO OFF VERIFY ON SET COMSPEC=C:DOSCOMMAND.COM SET PATH=C:;C:DOS;C:UTILS SET MFILE=C:UTILS SET PRO ...
-
Texas Instruments 3000 - page 87
Guidelines for Installing Applications Default CONFIG.SYS File Each line of the TravelMate 3000 default CONFIG.SYS Me and its purpose are defined in the table following the file listing. You can add commands required by your application program(s), but do not delete the existing default commands. FILES=20 BUFFERS=20 SHELL=C:DOSCOMMAND.COM /P /E:2 ...
-
Texas Instruments 3000 - page 88
Using Laptop Manager Laptop Manager, one of the utilities supplied with your TravelMate 3000, is an application control program. Laptop Manager provides two submenus into which you can insert application programs you have installed on the hard disk. You can then load application programs from one of the submenus with one keystroke, and from the oth ...
-
Texas Instruments 3000 - page 89
Using Laptop Manager Quick Commands Box Application programs you add to the Quick Commands box can be selected by pressing the function key (F1 to F11) you assign to it. For your convenience, the Laptop File Manager and several other utilities are assigned to the function keys. However, you can replace them with your own application programs using ...
-
Texas Instruments 3000 - page 90
Using a Password The TravelMate 3000 includes the Password utility, a program that limits access to your computer. Only those who know the password you specify using this utility can access your files. The password is valid until you remove or change it using the Password utility. In addition, Laptop Manager also provides password protection on a p ...
-
Texas Instruments 3000 - page 91
Using a Password Installing a Password Install a password as follows. 1. Highlight Install Password on the Password Utility menu and press the Enter key. The following menu displays: 2. Type a password of up to eight characters and press the Enter key. 3. Press the Enter key again to install the new password, or press the Esc key to cancel the acti ...
-
Texas Instruments 3000 - page 92
Using a Password Changing a Password Change the current password as follows. 1. Highlight the Change Password command on the Password Utility menu and press the Enter key. The following menu displays: 2. Type the current password and press the Enter key. Your entry is displayed as squares so that it cannot be seen by other people. If you type the c ...
-
Texas Instruments 3000 - page 93
Using a Password 4. Press the Enter key again to install the new password, or press the Esc key to abort the process and return to the Password Utility menu. Removing a Password Remove the current password as follows. 1. Highlight the Remove Password command on the Password Utility menu and press the Enter key. The following menu displays: 2. Type ...
-
Texas Instruments 3000 - page 94
Using a Password Entering the Password Once you install the password, you will see the following message every time you start up the computer: Enter Password: Type the password exactly as you created it and press the Enter key. q If you type the correct password, the screen clears and the system begins to load. q If you type the wrong password, the ...
-
Texas Instruments 3000 - page 95
Using a Password q If you forget the system password, you will not be able to use your computer. To regain access, it is necessary to disconnect the back-up battery for an extended period. This operation should only be performed by an authorized Texas Instruments dealer. Any other attempt to perform this operation could result in damage that will v ...
-
Texas Instruments 3000 - page 96
6 TravelMate 3000 Options This chapter tells you about: q Optio ns available for your Texas Instruments TravelMate 3000 Notebook Computer q How to install and use some of the options Contents Numeric Keypad ........................................................................................................ 6-2 Attaching the Keypad ............. ...
-
Texas Instruments 3000 - page 97
Numeric Keypad The optional Numeric Keypad (TI Part No. 2568033-0001) enables you to type numeric data more conveniently while still permitting data entry on the keyboard. You also have the convenience of direct access to some functions (such as the PgUp, PgDn, Home keys) without the need to also press the Fn key. Note that when the Numeric Keypad ...
-
Texas Instruments 3000 - page 98
RAM Modules The standard TravelMate 3000 Notebook Computer is equipped with 2 MB of main memory (RAM). If you need more RAM capacity, you can install four or eight RAM modules (TI Part No. 2566996-0001). Every four RAM modules increases RAM by 2 MB. Installing eight RAM modules increases total main memory to 6 MB. Installing the RAM Modules To inst ...
-
Texas Instruments 3000 - page 99
RAM Modules 3 Rotate the screwdriver toward the rear of the computer about 30 degrees until the top left corner of the keyboard loosens and raises about 1/4 inch (6 mm) above the computer case. 4. Holding the top left corner of the keyboard above the case with one hand, insert the screwdriver blade into the center slot (behind the F8 key) and rotat ...
-
Texas Instruments 3000 - page 100
RAM Modules Installing the Modules After removing the keyboard, install the four RAM modules as follows. You do not need any tools. Caution: Prevent component damage caused by electrostatic discharge (ESD). Use a high-impedance, grounded conductive floor mat or wrist strap to prevent ESD. Before touching the integrated circuit devices, discharge st ...
-
Texas Instruments 3000 - page 101
RAM Modules 3. Repeat steps 1 and 2 for the remaining three modules in the set, except insert the second module into socket XU10, the third module into socket XU12, and the fourth module into socket XU13. 4. If you are installing four more RAM modules, insert the first one in socket XU14, the second in XU15, the third in XU16, and the fourth in XU1 ...
-
Texas Instruments 3000 - page 102
RAM Modules 2. Hold the front of the keyboard in place while you lower the rear of the keyboard onto the computer case. 3. Insert the screwdriver blade between the Ins key and the Backspace key and gently press down on the keyboard until the rightmost catch snaps locked. 4. Insert the screwdriver blade between the F8 key and the 7 key and gently pr ...
-
Texas Instruments 3000 - page 103
Internal Modem The optional 2400-bps (bits-per-second) Internal Modem with Send-Fax and MNP Class 5 (TI Part No. 25669410003) adds a built-in modem to your TravelMate 3000. With the Internal Modem installed, you can connect your TravelMate 3000 to the telephone network and communicate with a remote modem. You also can make facsimile (fax) transmiss ...
-
Texas Instruments 3000 - page 104
80387SX Coprocessor The 80387SX Math Coprocessor (TI Part No. 2566997-0001) option for your TravelMate 3000 speeds up processing and improves throughput of calculations with application programs that support a math coprocessor. You can install the 80387SX Math Coprocessor option yourself, but installation requires partial disassembly of the compute ...
-
Texas Instruments 3000 - page 105
Other Options Extra Battery Pack Keeping an extra, fully charged battery pack (TI Part No. 2566962-0001) on hand can extend the time you can operate your computer on its internal battery. Install and remove the battery pack as described in Chapter 3. LapLink File Transfer Utility You can order the LapLink File Transfer Utility Kit (TI Part No. 2567 ...
-
Texas Instruments 3000 - page 106
Other Options Also set the Mouse Port item on Page 3 of the TravelMate 3000 Setup Program to On. Note: A mouse adapter cable with a built-in ferrite is shipped with U.S. and Canadian units. Failure to use the adapter cable, if provided, can cause noncompliance with FCC and DOC regulations. External Monitor The TravelMate 3000 supports the following ...
-
Texas Instruments 3000 - page 107
Other Options 1. Turn off power to both the external monitor and the TravelMate 3000. 2. Connect the 15-pin external VGA monitor cable from the external monitor to the 15-pin connector on the left side panel of the computer. 3. Turn on the TravelM ate 3000, then turn on the monitor. 4. At the MS-DOS C:> prompt type ALTVID and press the Enter ke ...
-
Texas Instruments 3000 - page 108
7 Taking Care of Your Computer This chapter tells you about: q Recommendations on how and where to use your TravelMate 3000 Notebook Computer q Cleaning the case and screen q How to get the most work from a battery charge and how to care for the battery Contents Do's and Don'ts ............................................................. ...
-
Texas Instruments 3000 - page 109
Do's and Don'ts The TravelMate 3000 Notebook Computer is a precision instrument containing many sensitive components. It should be handled with care. Here are some suggestions you can consider to help you get reliable service from your computer for many years: q Never use the TravelMate 3000 in harsh environm ents where it could be subjec ...
-
Texas Instruments 3000 - page 110
Cleaning the TravelMate 3000 Regularly take the time to check over your TravelMate 3000 Notebook Computer and clean the screen, keyboard, and case. You may spot trouble before it starts, and help continue to get efficient, trouble-free computing with your TravelMate 3000. Cleaning the Case It is important to keep the case of the TravelMate 3000 fre ...
-
Texas Instruments 3000 - page 111
Conserving Battery Power With a little care, you can maximize the time that your TravelMate 3000 will operate on a single battery charge. The following tips will help you run your computer for the longest possible time on battery power. q Keep the illumination of the LCD screen at the lowest comfortable brightness level. Reducing brightness even a ...
-
Texas Instruments 3000 - page 112
Care and Handling of the Battery The battery should be handled carefully to ensure maximum life. In particular: q Do not drop the battery or subject it to shocks. q Do not expose the battery to direct sunlight. q Do not expose the battery to moisture or chemicals. q Do not short the battery leads or connect the battery with the wrong polarity. q Ne ...
-
Texas Instruments 3000 - page 113
Care and Handling of the Battery q When using the computer for the first time, or after prolonged storage in temperatures above 95 degrees F (35 degrees C), a battery charge may not last as long as normal. This condition disappears after a few full discharge/recharge cycles. See 'Conditioning the Battery' in Chapter 3 for details. q After ...
-
Texas Instruments 3000 - page 114
A Specifications Central Processing Unit (CPU) Type: 16-bit 80386SX Clock Speeds: 8 MHz/ 10 MHz/20 MHz Memory RAM: 2 MB standard; 640 KB for conventional, 1408 KB for expanded or extended memory or shadow VGA/AT BIOS support LIM/EMS 4.0 support 16-bit bus width, 1 wait state Expandable up to 6 MB in 2-MB increments using RAM Module option ROM: 128 ...
-
Texas Instruments 3000 - page 115
Specifications Physical Dimensions Size Width: 1 1 inches (279 nun) Depth: 8.5 inches (216 mm) Height: 1.8 inches (46 mm) Weight: 5.7 lbs (2.6 kg), including battery, without options Power Source NiCad battery: 24 watt hours/AC Adapter AC Adapter Input: 100 to 25 0 Vac, 0.7 to 0.4 A, 50 to 60 Hz Output: +5 Vdc, 3.5 A max +7 Vdc, 1. 5 A max +8.5 Vdc ...
-
Texas Instruments 3000 - page 116
Specifications Shock Operating: 10 G applied in s ix orientations (positive and negative X, Y, and Z axes) Storage/Transit: 40 G applied in six orientations (positive and negative X, Y, and Z axes Standard Ports Parallel Port: Centronics-type, 25-pin Serial Port: RS-232C, 9-pin male DB-9 connector for full duplex asynchronous transmission at up to ...
-
Texas Instruments 3000 - page 117
Specifications Agency Approvals Main Unit: FCC, Part 15, Class B (U.S.A.) (including FCC Part 68 (U.S.A.) AC Adapter) DOC (Canada) UL, TUV, and CSA safety Options Internal Modem TI Part No. 2566941-0001 Power Requirements: Maximum 25 mA at -5 V Maximum 200 mA at +5 V Power Control Internal Modem operates under two power modes: Low Power: Only ring ...
-
Texas Instruments 3000 - page 118
Specifications 80387SX Coprocessor TI Part No. 2566997-0001 16-bit 80387SX, running at 20 MHz RAM Module Kit TI Part No. 2566996-0001 2-MB RAM module kit, extended or EMS support; up to two module kits can be installed for total 6-MB RAM Numeric Keypad TI Part No. 2568033-0001 Size Width: 3.9 inches (99 mm) Depth: 5.5 inches (139 mm) Height: 0.9 in ...
-
Texas Instruments 3000 - page 119
B Character Sets The TravelMate 3000 Notebook Computer character sets are identical to the IBM Code Pages for DOS version 4. 0 1. This appendix shows the character sets for Code Page 437 (United States), 850 (Multilingual), 863 (Canadian-French), and 865 (Nordic), with the decimal and hexadecimal codes for each character. The four character sets co ...
-
Texas Instruments 3000 - page 120
Character Sets Code Page 437, United States B-2 Character Sets ...
-
Texas Instruments 3000 - page 121
Character Sets Code Page 850, Multilingual Character Sets B-3 ...
-
Texas Instruments 3000 - page 122
Character Sets Code Page 863 (Canadian-French) B-4 Character Sets ...
-
Texas Instruments 3000 - page 123
Character Sets Code Page 865, Nordic Character Sets B-5 ...
-
Texas Instruments 3000 - page 124
C Keyboard Layouts The following diagrams show the TravelMate 3000 Notebook Computer keyboard layouts for the U.S.A. and international versions. Keyboard Layouts C-1 ...
-
Texas Instruments 3000 - page 125
Keyboard Layouts C-2 Keyboard Layouts ...
-
Texas Instruments 3000 - page 126
Keyboard Layouts Keyboard Layouts C-3 ...
-
Texas Instruments 3000 - page 127
Keyboard Layouts C-4 Keyboard Layouts ...
-
Texas Instruments 3000 - page 128
Keyboard Layouts Keyboard Layouts C-5 ...
-
Texas Instruments 3000 - page 129
D Diagnostics Your TravelMate 3000 Notebook Computer provides two diagnostic routines to make sure the computer and its peripherals are functioning as they should. One routine is automatic and takes place every time you turn on the computer. The other is accessed from a separate diagnostic program installed on the hard disk during manufacture. Powe ...
-
Texas Instruments 3000 - page 130
Diagnostics Park Fixed Disks The Park Fixed Disk function prepares the fixed disks for relocation. The fixed disk heads are placed over the diagnostic cylinder so that vibrations will not cause errors on the usable media. Diagnostics If you select the Diagnostics Program, a warning and informational menu displays. Press the N key to abort the diagn ...
-
Texas Instruments 3000 - page 131
Diagnostics When a single test or suite of tests is initiated, the Test Control Options and Test Results menu displays. On the left side of this menu is information relating to the test currently being performed. The right side of the menu contains the results of previously completed tests. Test Control Options The fields at the top of the menu rep ...
-
Texas Instruments 3000 - page 132
Diagnostics Choosing Specific Suites of Tests Many of the tests have submenus that permit you to select which parts of the test you want performed. When you select any of these tests, either individually (using F10) or as part of suite of tests (using F9), the submenus ask for additional information about the tests. If the tests are run multiple ti ...
-
Texas Instruments 3000 - page 133
Diagnostics Monochrome Adapter Test Attribute test Character test Text test Memory test Color Graphics Adapter Test Attribute test Character test Text test Page test Graphics test Background test Memory test EGA Adapter Test Attribute test Character test Text test Page test Graphics test Background test Memory test VGA Adapter Test Attribute test C ...
-
Texas Instruments 3000 - page 134
Diagnostics Asynchronous Communications Port Test Baud rate clock Internal transmit/receive Modem control lines External loopback (requires loopback connector) Additional Diagnostics The diagnostic program hard disk tests are all nondestructive except on the diagnostic cylinder. The tests perform seek tests, head tests, and controller tests, but do ...
-
Texas Instruments 3000 - page 135
Diagnostics The following table lists the classes of error codes. The numbers are in hexadecimal. Diagnostics Error Code Classes Code Description 01xx System planar board tests 07xx Keyboard tests 10xx Math coprocessor tests 17xx Video tests 20xx Asynchro nous ports tests 27xx LPT ports tests 30xx Memory tests 37xx Diskette/Fdisk tests The followin ...
-
Texas Instruments 3000 - page 136
Diagnostics Diagnostics Program Error Codes (continued) Code Class Failure Description 0107 System board System timer 0108 System board 8253 counters 0109 System board System timer interrupts (1) 010A System board System timer interrupts (2) 010B System board Processor flags 0110 System board CMOS memory 0111 System board Real time clock 0120 Syste ...
-
Texas Instruments 3000 - page 137
Diagnostics Diagnostics Program Error Codes (continued) Code Class Failure Description 1730 Video Cannot initialize video 2001 Serial Baud rate clock 2002 Serial Internal loopback data 2003 Serial Internal loopback control 2004 Serial External loopback data 2701 LPT Registers read/write 2702 LPT Control loopback 2703 LPT Printed pattern 2704 LPT Pr ...
-
Texas Instruments 3000 - page 138
Diagnostics Diagnostics Program Error Codes (concluded) Code Class Failure Description 3708 Disk DMA overrun 3709 Disk Attempt to DMA across 64 KB 370A Disk Bad sector flag found 370B Disk Bad cylinder detected 370C Disk Media type not found 3700 Disk Invalid format sectors count 370E Disk Control data mark detected 3710 Disk CRC or ECC error detec ...
-
Texas Instruments 3000 - page 139
Diagnostics Loopback Connections The serial and parallel communication tests in the Diagnostics Program offer optional loopback tests that expect loopback correctors to be placed on the output ports of the computer. The loopback connector pin assignments are fisted in the following tables. Loopback Connector Pin Assignments Serial Loopback Connecti ...
-
Texas Instruments 3000 - page 140
Diagnostics Hard Disk Format When you select the Hard Disk Format, the program displays the Format Fixed Disk menu. Use the Arrow keys to highlight the hard disk you want formatted or analyzed and press the Enter key. Of course, you can select only hard disks installed in your computer. After you have selected a hard disk, the program displays a wa ...
-
Texas Instruments 3000 - page 141
Diagnostics To manually add a bad track to the table, press the Ins key. Use the Arrow keys or the Enter key to select between cylinder and head fields. After the cylinder and head are entered, press the F10 or Enter key and the new entry will be added to the table. If an invalid head or cylinder value is entered, the program displays a menu permit ...
-
Texas Instruments 3000 - page 142
Diagnostics Caution: This performs a destructive analysis of the hard disk media (all data on the hard disk will be erased). Any bad tracks found during the analysis are automatically added to the bad track table. As bad tracks are found, they are reformatted as bad so that a subsequent MS-DOS FORMAT operation does not attempt to use these areas on ...
-
Texas Instruments 3000 - page 143
Diagnostics q Each track of the hard disk is reformatted using the current interleave value. q Each track in the bad track table is reformatted as bad so that it cannot be used. q The program performs a surface analysis on the media, reformats any additional bad tracks as bad, and adds them to the list. Using this option is equivalent to performing ...
-
Texas Instruments 3000 - page 144
E Troubleshooting This appendix is designed to help you solve common problems you may encounter while using your TravelMate 3000 Notebook Computer. If you encounter a problem not listed here, please contact your Texas Instruments reseller, or you can telephone or fax Texas Instruments at one of the numbers fisted on the page near the end of this ma ...
-
Texas Instruments 3000 - page 145
...
-
Texas Instruments 3000 - page 146
Troubleshooting Computer comes on Internal battery pack still too when turned on but warm -Wait about 3 more turns off before boot- minutes and try agai n. ing. Computer Power in- Automatic discharge cycle dicator light on, Low not complete -Leave Power Batt Indicator blink- switch in on position until ing, screen blank, and all indicator lights go ...
-
Texas Instruments 3000 - page 147
Troubleshooting Computer in automatic power- saving mode -Press Shift key to turn on display. if Power indicator is orange, press Fn-F4 (Stndby) keys to resume operation. None of the above -Screen power unit may be faulty. Contact your Texas Instruments reseller. When using a mouse, Setup Program Backlight Off the built-in LCD screen set to N minut ...
-
Texas Instruments 3000 - page 148
Troubleshooting Special functions do Application program oven-id- not work (Set Up, Alt- ing computer BIOS interrupts Ctrl-Esc, speed control - Contact your application keys) program provider. The unit starts up but TravelMate 3000 hardware - a message indicates Turn the unit off, wait 5 that a power-up test seconds, then turn unit on has failed. a ...
-
Texas Instruments 3000 - page 149
Troubleshooting Amber indicator on -Internal battery pack not fully charged. Amber indicator off, internal battery pack not installed and power switch set to off - Set computer power switch to on and run on ac power or install battery pack. Amber indicator off-Internal fault: contact your Texas Instruments reseller. Pressing Fn-F4 keys The BatteryP ...
-
Texas Instruments 3000 - page 150
Error Messages Power-up self-tests are the system tests and component initialization processes performed by the TravelMate 3000 AT compatible ROM BIOS. The self-tests first initialize and test the central hardware. The central hardware must function properly before further system tests can be run. In general, a failure in a test of the system board ...
-
Texas Instruments 3000 - page 151
Error Messages Fixed disk failure Turn off the computer, wait 5 seconds, and turn the com- puter on again, or press the Ctrl-Alt-Del keys to reboot the system. If that does not work, run the DIAG program to check the hard disk drive as described in Appendix D, then contact your Texas Instruments reseller. Fixed disk read failure - Defective working ...
-
Texas Instruments 3000 - page 152
Error Messages Keyboard stuck key Jammed key - Try pressing failure the key again. Run the DIAG program to check all keys as described in Appendix D. Missing operating System bootfiles on hard system disk bad or missing. Hard disk type incorrect in Setup Progr am -Press the Ctrl-Alt- Setup keys to access the Setup Program and check the Hard Disk ty ...
-
Texas Instruments 3000 - page 153
Error Messages Non-System disk or Floppy in drive A not a disk error. Replace and bootable floppy - Replace press any key when the floppy in drive A with a ready bootable floppy. When for- matting MS-DOS bootable floppies, be sure to add the /S option to the FORMAT com- man d (see your MS-DOS User's Manual ). Time-of-day not set Failed RTC chi ...
-
Texas Instruments 3000 - page 154
Restoring MS-DOS System Files The MS-DOS files COMMAND.COM, IO.SYS, and MSDOS.SYS are necessary for the operation of your computer. If any of these files are accidentally deleted or modified, your computer will not function. This appendix describes the procedure for restoring these files without affecting the applications and data files that may be ...
-
Texas Instruments 3000 - page 155
Restoring MS-DOS System Files 3. When the A> prompt is displayed, remove the SHELL floppy and insert the Select Copy floppy, and type SYS C: and press the Enter key. The computer should display the message System transferred and then display the A> prompt. 4. At the A> prompt type COPY COMMAND.COM C:DOS and press the Enter key. The comput ...
-
Texas Instruments 3000 - page 156
F Configuring Memory Introduction Computers handle information as strings of binary digits: ones and zeros. A single I or 0 is refer-red to as a bit, the smallest unit of information handled by the computer. A group of eight bits, referred to as a byte, is used to represent single characters or numbers such as "A" or "5". The si ...
-
Texas Instruments 3000 - page 157
Configuring Memory This appendix describes the various areas of memory (RAM) and how you can make memory more efficient by configuring it in conjunction with the memory management device drivers supplied with your TravelMate 3000. F-2 Configuring Memory ...
-
Texas Instruments 3000 - page 158
TravelMate 3000 Memory Areas MS-DOS directly accesses up to 640 KB of RAM for the execution of programs and commands and for storing temporary data. MS-DOS cannot directly access memory beyond this 640-KB limit . The amount of standard default RAM (640 KB) in the TravelMate 3000 is displayed on the Setup Program menu as Standard (Memory), and it ca ...
-
Texas Instruments 3000 - page 159
TravelMate 3000 Memory Areas Extended Memory Extended memory is internal RAM above 1024 KB. MS-DOS cannot directly access Extended memory as system memory, but the memory can be configured as one or more RAM disks. It can also be accessed by application programs specially written to use Extended memory. The HIMEM.SYS device driver described later i ...
-
Texas Instruments 3000 - page 160
TravelMate 3000 Memory Areas Before you can use Expanded memory, you must install the EMM.SYS device driver as described in the next section, "Memory Device Drivers." You need not install the Expanded memory driver if your application program does not support use of Expanded memory. Configuring Memory F-5 ...
-
Texas Instruments 3000 - page 161
Memory Device Drivers The following four device drivers are provided to manage the TravelMate 3000 memory: q EMM.SYS - device driver supports LIM-EMS Expanded memory. q HIMEM.SYS - device driver is an extended memory manager that supervises the use of the computer's Extended memory so that no two application programs can use the same memory at ...
-
Texas Instruments 3000 - page 162
Memory Device Drivers EMM.SYS The EMS memory manager provided with your TravelMate 3000, the EMM.SYS device driver, conforms to version 4.00 of the Lotus/Intel/Microsoft Expanded Memory Specification (EMS). EMM.SYS enables areas of system memory to be used as Expanded memory. Note: You cannot use EMM.SYS with Windows 3.0 in 386 standard or enhanced ...
-
Texas Instruments 3000 - page 163
Memory Device Drivers Some application programs may require "backfill" memory, which is the unused area of standard memory that can be used by EMM.SYS as Expanded memory. For example, an application program may require only 256 KB or 512 KB of standard memory, leaving 384 KB and 128 KB of backfill. memory space, respectively, for use as E ...
-
Texas Instruments 3000 - page 164
Memory Device Drivers If you do not specify any parameters, EMM.SYS uses the default values for each. Numeric values (nnnn) should be specified in decimal unless specifically noted otherwise in the following descriptions. Memory sizes should be specified in kilobytes (1024 bytes) without the last three digits at the end of the number; for example, ...
-
Texas Instruments 3000 - page 165
Memory Device Drivers Contexts = nn (C=) specifies the number of contexts for windows 0 - 3 that can be saved by processes using EMS memory. The maximum number of contexts is 255; the minimum is 3. The default is the number of handles that are allocated. Depth = nn (D=) specifies the number of consecutive contexts that can be saved for a given hand ...
-
Texas Instruments 3000 - page 166
Memory Device Drivers Include = xxxx-xxxx (L=) specifies a range of addresses that should always be used for EMS mapping. By default, the memory manager automatically excludes areas known to contain ROMs or video RAM. This parameter allows you to include a range of addresses that might be excluded by memory manager's automatic selection proces ...
-
Texas Instruments 3000 - page 167
Memory Device Drivers Memory Manager Error Messages Error messages displayed by the memory manager are divided into two groups. The following first group displays general memory manager errors. Invalid parameter specified - One of the parameters specified on the command line in your CONFIG.SYS file is invalid. Expected equal after parameter - One o ...
-
Texas Instruments 3000 - page 168
Memory Device Drivers Number of contexts must be at least 3 - The number of contexts specified is less than 3. The number of contexts specified must be between 3 and 255. See "Contexts" parameter earlier in this appendix. Number of contexts cannot exceed 255 - The number of contexts specified is greater than 255. The number of contexts sp ...
-
Texas Instruments 3000 - page 169
Memory Device Drivers The following second group of error codes are specific to the TACT 83000 memory manager. Invalid hardware for memory manager - The memory manager was run on a system which did not contain the TACT 83000 chip set. No EMS memory allocated - No Expanded memory was specified using the Memory parameter, and no memory remained unall ...
-
Texas Instruments 3000 - page 170
Memory Device Drivers if you need to specify special conditions for the use of the high-memory area, use the command in the following form: DEVICE=C:DOSHIMEM.SYS [/HMAMIN=h][/NUM- HANDLES=n] where: /HMAMIN=h h is the minimum amount of memory required by a TSR program or device driver to be loaded into HAM specify the amount of memory in kilobytes ...
-
Texas Instruments 3000 - page 171
Memory Device Drivers RAMDRIVE.SYS A RAM disk is a portion of your computer's memory configured to simulate a disk drive. Such a disk, which may be called a virtual disk, can be accessed much faster than a normal disk drive. The data stored on a RAM disk disappears when computer power is turned off, so you must copy the contents of the RAM dis ...
-
Texas Instruments 3000 - page 172
Memory Device Drivers SMARTDRV.SYS SMARTDRV.SYS is a disk-caching program used to reduce the time it takes your computer to read data from the hard disk. When SMARTDRV.SYS is installed, information from the hard disk is temporarily stored in a cache in Extended or Expanded memory. When needed, the data can be accessed by the processor directly from ...
-
Texas Instruments 3000 - page 173
G Connector Pin Assignments RS-232C Connector Nine-Pin RS-232C Serial Connector Pin No. Signal Name Abbreviation Direction 1 Carrier detect CD Input 2 Receive data RD Input 3 Transmit data TD Output 4 Data terminal ready DTR Out put 5 Signal ground SG 6 Data set ready DSR Input 7 Request to send RTS Output 8 Clear to send CTS Input 9 Ring indicator ...
-
Texas Instruments 3000 - page 174
Connector Pin Assignments 15-Pin VGA External Monitor Connector Pin No. Signal Name Direction 1 Red video Output 2 Green video Output 3 Blue video Output 4 Not used 5 Ground 6 Red return Input 7 Green return Input 8 Blue return Input 9 Not used 10 Ground 11 Not used 12 Not used 13 Horizontal sync Output 14 Vertical sync Out put 15 Not used Note: Mo ...
-
Texas Instruments 3000 - page 175
H Screen Standards This appendix summarizes the screen standards supported by the TravelMate 3000 Notebook Computer's internal display adapter. MDA (Monochrome Display Adapter) The MDA standard supports a 720-by-350 monochrome text display using a 9-by-14 pixel character box. The TravelMate 3000 LCD screen supports MDA by displaying an 80- col ...
-
Texas Instruments 3000 - page 176
Screen Standards EGA (Enhanced Graphics Adapter) The EGA standard supports 640-by-350 pixel monochrome or 16-color graphics, 640-by- 200 pixel and 320-by-200 pixel 16-color graphics. The EGA standard also uses an 8-by- 14 pixel character box for text displays. The TravelMate 3000 LCD screen supports EGA by displaying text in an 80-column by 25-line ...
-
Texas Instruments 3000 - page 177
Screen Standards The TravelMate 3000 LCD screen supports VGA by displaying text in an 80-column by 25-line text display with 16 shades of gray (selectable from 32 shades) in an 8-by- 16 pixel character box in a 640-by-400 pixel display area centered on the screen. The TravelMate 3000 supports color graphics by displaying colors as 32 shades of gray ...
-
Texas Instruments 3000 - page 178
Screen Standards External Monitor Support The TravelMate 3000 supports all IBM standard VGA video in addition to 800 by 600, 1024 by 768, and 132-column Paradise extended modes. Paradise Modes Supported Mode No. (hex) Resolution Font Clock Memory Size 132-column Text Modes (Supported on CRT only)* 54 32 x 43 x 16 8 x 8 44.7 MHz 256 KB 55 132 x 25 x ...
-
Texas Instruments 3000 - page 179
Glossary This glossary explains many of the terms found in this manual as well as other computer- related terms you many encounter. access - The ability to obtain data from or place data into internal memory, a floppy diskette, or the hard disk. access shutter - A metal cover on a floppy diskette that slides open to allow the computer to read or wr ...
-
Texas Instruments 3000 - page 180
Glossary backlight - A feature that allows you to control background brightness for better readability. backing up - Duplicating a program or file onto a separate storage medium so that a copy will be preserved against possible loss or damage to the original. backup - A duplicate copy of information or programs; usually stored on a diskette and kep ...
-
Texas Instruments 3000 - page 181
Glossary boot - To start your computer; also called start-up and power-up. bps - See bits per second. brightness control - A control that allows you to adjust the brightness of the display. buffer - A portion of the computer's memory that temporarily holds information used by a program; for example, the portion of a document you are working on ...
-
Texas Instruments 3000 - page 182
Glossary character set - A system of codes, such as ASCII, that assigns a special standardized group of binary digits to each character. clock - A timing device that coordinates all internal events in your computer. CMOS - An acronym for Complementary Metal Oxide Semiconductor; a large-scale integration technology that requires low power consumptio ...
-
Texas Instruments 3000 - page 183
Glossary contrast control - A control that allows you to adjust how data shows up against the background of the display screen. control code - A code that initiates some kind of physical control action that is not printed (such as line feed and tab), turns off an external device, or, in combination with other characters, defines unique commands (fo ...
-
Texas Instruments 3000 - page 184
Glossary data - Information that is input to your computer and is then processed by mathematical and logical operations so that, ultimately, it can be output in a sensible form. It usually consists of numerals, letters, or symbols that describe an object, idea, condition, relationship, or other information. data base - A collection of related infor ...
-
Texas Instruments 3000 - page 185
Glossary disk drive - A device that rotates magnetic media and accesses data by means of a read/write head. diskette - See floppy diskette. DOS - The disk operating system, programs that act as translator between you and your computer; also see operating system expanded memory - The memory that utilizes an area of the computer memory as a window, t ...
-
Texas Instruments 3000 - page 186
Glossary fixed disk drive - See hard disk drive. floppy diskette - A flexible, flat, circular medium that magnetically records and provides access to stored data. It is divided into concentric circular tracks and wedge-shaped sectors. The diskette is sealed in a protective square envelope that is lined with a soft material that cleans as the disket ...
-
Texas Instruments 3000 - page 187
Glossary hexadecimal - A numbering system that consists of 16 symbols, 0 to 9 and A to F; used by programmers as a convenient method of expressing binary values. input - Information that enters the computer. input/output - An operation that transfers information from the central processing unit to a device or from a device to the central processing ...
-
Texas Instruments 3000 - page 188
Glossary load - To copy information from a storage device, such as a diskette or a hard disk drive, into internal memory of the computer. Also called download loop - A series of instructions or one instruction in a program that is repeated a prescribed number of times, followed by a branch instruction that exits the program from the loop. main dire ...
-
Texas Instruments 3000 - page 189
Glossary multiuser system - A system in which the computer and other external devices are shared in any one of several arrangements by several people. operating system - A set of programs that control the operation of the computer. Typically, the operating system regulates space allocation, keeps track of files, saves and retrieves files, and manag ...
-
Texas Instruments 3000 - page 190
Glossary programming language - A set of words, abbreviations, or symbols that are converted into the binary numbers that represent instructions to the computer. Programming languages enable programmers to write instructions using words or symbols and avoid the time-consuming task of entering the long string of Os and 1s that represent the numeric ...
-
Texas Instruments 3000 - page 191
Glossary set up - See configure . software - Computer programs, usually supplied on floppies or on ROM. Contrast with hardware. system board - An internal circuit board that holds the integrated circuits for the microprocessor, memory, and clock in your computer. turbo operation - A feature of a computer that increases its data processing speed by ...
-
Texas Instruments 3000 - page 192
Index a .............................................................. c ac adapter .................................................... cache .................................................... F- 17 connecting ........................................ 3-6 Caps Lock indicator .............................. 2-20 jack ............................... ...
-
Texas Instruments 3000 - page 193
Index display ............................................................................ 2-4 standard/reverse (video) ................................................ 2-5 conventions used in manual ............................................................... vi cover closed alarm, setting ....................................................... ...
-
Texas Instruments 3000 - page 194
Index utilities ....................................................................... 3-19 Hercules Graphics Card ..................................................................................... H-3 HGC ......................................................................................................... H-3 high-memory area ............. ...
-
Texas Instruments 3000 - page 195
Index LCD screen controls ............................................................................................ 2-4 left side panel ....................................................................................................... 2-6 lock keys 4-15 Low Battery indicator .................................................................. ...
-
Texas Instruments 3000 - page 196
Index Pause key ........................................................................................................ 2-16 physical dimensions ............................................................................................ A-2 pin assignments, connector ................................................................................ ...
-
Texas Instruments 3000 - page 197
Index screen ................................................................ 4-14 standard communication port ............................ 4-19 stop bits ............................................................. 4-19 time ..................................................................... 4-6 Setup key ....................................... ...
-
Texas Instruments 3000 - page 198
Getting Support for Your TI Product Texas Instruments and your Texas Instruments authorized reseller want you to succeed with your TI product. If you have questions about or operating difficulties with your TI product, follow these steps to get support. 1. Call your dealer. Your dealer should be the first person you call when you have questions or ...
-
Texas Instruments 3000 - page 199
Warranty and Service The TravelMate 3000 Notebook Computer and its Texas Instruments options are warranted for 12 months from the purchase date. Standard Warranty Texas Instruments offers a 1 -day turnaround for domestic units carried In to local Customer Service Centers and a 5-day turnaround from receipt time at the National Service Center for un ...
-
Texas Instruments 3000 - page 200
Repair Request Form Your name and address Your Name Company Name Address City State -Zip Code Phone number ( ) Ext. Product serial number Unit(s) you are returning (check where applicable) q TravelMate 3000 q 2 MB RAM Module Kit q Numeric Keypad q 80387SX Coprocessor q Internal Modem q AC Adapter q Internal Battery Type of Claim q Warranty claim (a ...
-
Texas Instruments 3000 - page 201
Notice This computer has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This computer generates, uses, and can radiate radio frequency energy and, if not installed ...
-
Texas Instruments 3000 - page 202
Texas Instruments reserves the right to change its product and service offering at any time without notice ...
-
Texas Instruments 3000 - page 203
TravelMate Notebook Computer Major Components ...
-
Texas Instruments 3000 - page 204
Manual Pat No. 2566946-0001, Rev. C* Printed in U.S.A. T EXAS I NSTRUMENTS ...
Do you have a question concerning Texas Instruments 3000?
Use the form below
If you did not solve your problem by using a manual Texas Instruments 3000, ask a question using the form below. If a user had a similar problem with Texas Instruments 3000 it is likely that he will want to share the way to solve it.