English dropdown-ico

Manual Pelco IPSXM-7

16 pages 0.35 mb
Download

Go to site of 16

Summary
  • Pelco IPSXM-7 - page 1

    INSTALLATION ExSite ™ Series Explosionproof Power Module C313M-D (8/05) IPSXM-2 and IPSXM-7 ...

  • Pelco IPSXM-7 - page 2

    ...

  • Pelco IPSXM-7 - page 3

    C313M-D (8/05) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco IPSXM-7 - page 4

    4 C313M-D (8/05) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 6. T o reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from t ...

  • Pelco IPSXM-7 - page 5

    C313M-D (8/05) 5 Getting Started Thank you for purchasing Pelco’ s ExSite ™ Series explosionproof integrated positioning system. This manual includes instructions for installing the power module for the ExSite Series system. For complete system installation instructions refer to the installation manual placed in the pan and tilt box. Once the c ...

  • Pelco IPSXM-7 - page 6

    6 C313M-D (8/05) Install the Power Module Attach the power module to the mounting surface. Use only installation methods and materials capable of supporting four times the maximum specified load of the system (220 lb/100 kg). NOTE: If required, install the optional TXB translator , fiber module, or UTP board before installing the power module. Re ...

  • Pelco IPSXM-7 - page 7

    C313M-D (8/05) 7 Connect Wiring Refer to the following information to connect the wires and cables as required. NOTES: • Relay 3 is allocated specifically for an external washer (not supplied by Pelco). • All relays are specified for 32 VDC, 0.5 A. • Wiring/cable for UTP and fiber optic are not provided on the wire harness. The installer m ...

  • Pelco IPSXM-7 - page 8

    8 C313M-D (8/05) DIP Switch Settings Configure the receiver address, termination, and baud setting for the system. The DIP switches to configure these settings are located on the top of the power module. NOTE: No DIP switch settings are required for Coaxitron ® control. Figure 3 shows the default settings for the DIP switches. Refer to the follo ...

  • Pelco IPSXM-7 - page 9

    C313M-D (8/05) 9 T ables ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF OFF OFF OFF 2 ON OFF OFF OFF OFF OFF OFF OFF 3 OFF ON OFF OFF OFF OFF OFF OFF 4 ON ON OFF OFF OFF OFF OFF OFF 5 OFF OFF ON OFF OFF OFF OFF OFF 6 ON OFF ON OFF OFF OFF OFF OFF 7 OFF ON ON OFF OFF OFF OFF OFF 8 ON ON ON OFF OFF OFF OF ...

  • Pelco IPSXM-7 - page 10

    10 C313M-D (8/05) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 49 ON OFF OFF OFF ON ON OFF OFF 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON OFF ON ON OFF OFF 53 ON OFF ON OFF ON ON OFF OFF 54 OFF ON ON OFF ON ON OFF OFF 55 ON ON ON OFF ON ON OFF OFF 56 OFF OFF OFF ON ON ON OFF OFF 57 ON OFF ...

  • Pelco IPSXM-7 - page 11

    C313M-D (8/05) 11 T able B. D Protocol Receiver Address (Continued) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 143 ON ON ON ON OFF OFF OFF ON 144 OFF OFF OFF OFF ON OFF OFF ON 145 ON OFF OFF OFF ON OFF OFF ON 146 OFF ON OFF OFF ON OFF OFF ON 147 ON ON OFF OFF ON OFF OFF ON 148 OFF OFF ON OFF ON OFF OFF ON 149 ON OFF ON O ...

  • Pelco IPSXM-7 - page 12

    12 C313M-D (8/05) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 239 ON ON ON ON OFF ON ON ON 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON OFF OFF ON ON ON ON 243 ON ON OFF OFF ON ON ON ON 244 OFF OFF ON OFF ON ON ON ON 245 ON OFF ON OFF ON ON ON ON 246 OFF ON ON OFF ON ON ON ON ADDRESS SWITCH SE ...

  • Pelco IPSXM-7 - page 13

    C313M-D (8/05) 13 Specifications ELECTRICAL Input V oltage 24 V AC or 100-240 VAC Input V oltage Range ±10% Power Consumption Maximum 60 watts (120 V A) per system Electrical Connections 6-foot wire harness with connections for power , video, data control, alarm inputs, and auxiliary outputs MECHANICAL Cable Entry One 0.75-inch (1.91 cm) NPT thre ...

  • Pelco IPSXM-7 - page 14

    14 C313M-D (8/05) ...

  • Pelco IPSXM-7 - page 15

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series ...

  • Pelco IPSXM-7 - page 16

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

Manufacturer Pelco Category Cooktop

Documents that we receive from a manufacturer of a Pelco IPSXM-7 can be divided into several groups. They are, among others:
- Pelco technical drawings
- IPSXM-7 manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco IPSXM-7
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco IPSXM-7.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco IPSXM-7, service manual, brief instructions and user manuals Pelco IPSXM-7. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco IPSXM-7.

Similar manuals

A complete manual for the device Pelco IPSXM-7, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco IPSXM-7 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco IPSXM-7.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco IPSXM-7 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco IPSXM-7, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco IPSXM-7, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco IPSXM-7 - which should help us in our first steps of using Pelco IPSXM-7
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco IPSXM-7
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco IPSXM-7 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco IPSXM-7?

Use the form below

If you did not solve your problem by using a manual Pelco IPSXM-7, ask a question using the form below. If a user had a similar problem with Pelco IPSXM-7 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)