Manual Lochinvar SMART TOUCH 1

20 pages 1.84 mb
Download

Go to site of 20

Summary
  • Lochinvar SMART TOUCH 1 - page 1

    Th i s m an ua l m us t o nl y b e u se d b y a qualified heating installer / serv ice technician. Read all instructions, including this manual, the SYNC Installation and Operation Man ual, and the SYNC Serv ice M anual, before installing. Perform steps in the order given. Failure t o comply could result in sev ere personal injur y , death, or subs ...

  • Lochinvar SMART TOUCH 1 - page 2

    2 Contents 1. INST ALLA TION Program Installation ..................................................... 3 USB Installation............................................................ 3 Program Setup ............................................................. 3 PC to Unit Connection.................................................. 3 S tarting the ...

  • Lochinvar SMART TOUCH 1 - page 3

    PC Program Instructions 1 Installa tion Prog r am installa tion There are tw o programs available for programming and monitoring the SYNC boilers. SITECS937L ab is used to monitor the operation of the boiler and program a few display- related parameters . SMAR T TOUCH PC i s u s e d t o p r o g r a m the bulk of the parameters in the contr ols. T o ...

  • Lochinvar SMART TOUCH 1 - page 4

    4 1 Installa tion Star ting the prog r am T o start one of the programs, double-click on the ic on (if you put it on your desktop), or click on Start, then Programs, and select the program you wish to start. See FIG 1-1 and FIG 1-2 abov e. There are tw o access levels for this program. The user access level allows only c er tain settings to be chan ...

  • Lochinvar SMART TOUCH 1 - page 5

    2 Sta tus Scr een 5 Figure 2-1 SMART TOUCH S tatus Screen T o monitor and r e cor d the oper ation of the heater , click on the Status tab along the top of the Main Scr een w indow (FIG. 1-1, page 4). W hen using the SITECS937Lab progr am, you will need to choose whic h controller you wish to monitor . The Status Screen will appear (see FIG. 2-1 ab ...

  • Lochinvar SMART TOUCH 1 - page 6

    2 Sta tus Scr een 6 At the t op r ight of the window is the Fan Speed status information. I ncluded in the Fan Speed status are Min., Max., and Ignition fan speeds. If Ramp Delay is activat ed, the Ramp Delay limit is sho w n. The target and actual fan speeds are display ed, and if the ac tual speed is within acceptable limits. If the SMART T OUCH ...

  • Lochinvar SMART TOUCH 1 - page 7

    7 3 Gr aphics Scr een The Graphics Screen allows y ou to observe the changes in various readings while the heater operates (see FIG. 3-1). N ote that the vertical scale has two numbers for each division. By default, the Outlet T emperature, Inlet T emperature, System Supply T emperature (if connected), Outdoor T emperature (if connect ed), T ank Se ...

  • Lochinvar SMART TOUCH 1 - page 8

    8 4 F ault Histor y Screen Figure 4-1 Fault History Screen The Fault Hist or y Screen provides historical data about the operation of the SMAR T TOUCH co nt rols.. Click on the Fault history button along the top of the Main Screen window (FIG. 1-1), and then click on Read from Control in the pull-down menu. After uploading data fr om the selected p ...

  • Lochinvar SMART TOUCH 1 - page 9

    9 5 Cascade Screen Figure 5-1 Cascade Screen The Cascade Screen pro v ides the status of the cascade system. The PC must be connect ed to the Leader (address 0-1) appliance. Click on the Cascade button along the top of the Main Scr e en window (FIG. 1-1). The Cascade Syst em area shows the powe r demand and setpoint, the boiler pump status, the boi ...

  • Lochinvar SMART TOUCH 1 - page 10

    6 P ar ameter s Parameter infor mation screens By acc essing the Parameter I nformation Screens on the SMAR T TOUCH program, the installer can v iew all of the SMAR T TOUCH parameters. The installer can also change certain specific parameters to fine tune the operation of the boiler to the installation. NOTE The PC cable m ust be connected to eithe ...

  • Lochinvar SMART TOUCH 1 - page 11

    11 6 P ar ameter s (continued) Changeable par ameter s The following is a brief discussion of the changeable parameters, their default setting s, the range of adjustment, and their location. The title for the par ameters ma y differ slightly from the PC to the boiler displa y . T o prevent confusion, the boiler display v ersion w ill be listed in p ...

  • Lochinvar SMART TOUCH 1 - page 12

    12 PC Program Instructions 6 P ar ameter s Set 2: Functional Data Set 2 is accessed b y clicking on Parameters at the t op of the Main Scr een window , then clicking on Set 2: Functional Data on the pull-down menu (FIG. 6-1, page 10). Cascade control P arameters 2DJ and 2DK determine the time dela ys used by the Cascade. T o access the Cascade para ...

  • Lochinvar SMART TOUCH 1 - page 13

    13 PC Program Instructions 6 P ar ameter s (continued) Pa r a m e t e r 2EB sets the pump delay time for the boiler pump after an ov er-temperature c ondition. This time is adjustable from 0 minut es to 40 minutes. The default time is 2 minutes. If the boiler pump or HW pump have not been activ e in a 24 hour period, the SMAR T TOUCH will activate ...

  • Lochinvar SMART TOUCH 1 - page 14

    14 PC Program Instructions 6 P ar ameter s SH off-on differential (SH off/on df) The SH Off-on Differential sets ho w many degrees below the turn-off temperature the outlet temperatur e has to go before the boiler will turn on. This parameter can be changed b y accessing parameter 4AE . The temperature range of this parameter is 0°F to 86°F . The ...

  • Lochinvar SMART TOUCH 1 - page 15

    15 PC Program Instructions 6 P ar ameter s (continued) T ank differential temp This parameter determines how far belo w the tank setpoint the tank sensor temperature must go t o star t a HW call for heat. This setting can be adjusted by accessing parameter 4A T . The temperature range is 0°F (0°C) to 100°F (38°C). The default value is 5°F (3.5 ...

  • Lochinvar SMART TOUCH 1 - page 16

    16 PC Program Instructions 6 P ar ameter s Cascade Each burner control in the Cascade m ust be given a unique address. This address can be changed by ac cessing parameter 4CC . The Leader (top) burner (to which the thermostat/zone control, system sensor , and system pump (if controlled by the boiler) are c onnected) must be set t o address 0. All t ...

  • Lochinvar SMART TOUCH 1 - page 17

    17 PC Program Instructions 6 P ar ameter s (continued) Figure 6-10 Parameter Set 4F OA reset water temp at min outdoor temp (4FC) (Reset T Lo Out) W h en the outdoor air t emperature drops to its minimum setting ( 4FC ), the water temperature setpoint will be at this value. Howev er , if the SH user setpoint ( 4AA ) is lower , it will ov er ride th ...

  • Lochinvar SMART TOUCH 1 - page 18

    18 PC Program Instructions 6 P ar ameter s Figure 6-1 1 Outdoor Air Reset Curve Figure 6-12 Parameter Set 4G BMS Setpoint at min volt age (BMS setpt min V) If par ameter 4CB is set t o 2, the co ntrol must kno w what minimum setpoint temperature t o use. This can be changed b y accessing parameter 4GA . The temperature range for this parameter is 3 ...

  • Lochinvar SMART TOUCH 1 - page 19

    19 PC Program Instructions 6 P ar ameter s (continued) Figure 6-13 Save Parameter File Window Storing p arameters on your PC Once y ou have customiz ed the parameters for a particular heater , y ou can store the new settings on your PC. This w ill allow y ou to restor e these settings should you ha ve to replac e the SMAR T TOUCH c ontrol, or allo ...

  • Lochinvar SMART TOUCH 1 - page 20

    Revision Notes: Revision A initial release. SYNC-PCP Rev A Printed in the USA 4/10 ...

Manufacturer Lochinvar Category Laptop

Documents that we receive from a manufacturer of a Lochinvar SMART TOUCH 1 can be divided into several groups. They are, among others:
- Lochinvar technical drawings
- SMART TOUCH 1 manuals
- Lochinvar product data sheets
- information booklets
- or energy labels Lochinvar SMART TOUCH 1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Lochinvar SMART TOUCH 1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Lochinvar SMART TOUCH 1, service manual, brief instructions and user manuals Lochinvar SMART TOUCH 1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Lochinvar SMART TOUCH 1.

Similar manuals

A complete manual for the device Lochinvar SMART TOUCH 1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Lochinvar SMART TOUCH 1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Lochinvar SMART TOUCH 1.

A complete Lochinvar manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Lochinvar SMART TOUCH 1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Lochinvar SMART TOUCH 1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Lochinvar SMART TOUCH 1, that we can find in the current document
3. Tips how to use the basic functions of the device Lochinvar SMART TOUCH 1 - which should help us in our first steps of using Lochinvar SMART TOUCH 1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Lochinvar SMART TOUCH 1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Lochinvar SMART TOUCH 1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Lochinvar SMART TOUCH 1?

Use the form below

If you did not solve your problem by using a manual Lochinvar SMART TOUCH 1, ask a question using the form below. If a user had a similar problem with Lochinvar SMART TOUCH 1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)