English dropdown-ico

Manual Taylor 428

42 pages 1.27 mb
Download

Go to site of 42

Summary
  • Taylor 428 - page 1

    OPERA T OR’S MANUAL Model 428 Shake/Slush Freezer Original Operating Instructions 055058 - M Februar y , 2001 (Or igi nal Publicat ion) (Updat ed 8/25/ 14) ...

  • Taylor 428 - page 2

    Com plete this page for quick r efere nce when ser vice is r equired: T aylor Distri butor: Address: Phone: Serv ice: Par ts: Date of Installation: Infor mation found on the da ta label: Model Number: Seri al Number: Electrical S pecs: V oltage Cycle Phase Maximum Fuse Si ze: A Minimum Wi re Ampacity: A E 2001 Carrier Comm ercial Ref riger ation, I ...

  • Taylor 428 - page 3

    Mode l 42 8 T able of Conte nts T a ble of Contents Section 1 T o the Installer 1 ............................................ Section 2 T o the Operator 4 ........................................... Section 3 S afety 5 .................................................... Section 4 Op erator Par ts Identification 7 ............................... M ...

  • Taylor 428 - page 4

    T able of Conte nts Mode l 42 8 T able of Contents - Page 2 Se ction 10 Lim ited W arr anty on Equipm ent 32 ............................ Section 1 1 Limited W arranty on Par ts 34 ................................. Wiri ng Diagrams 37 ...................................................... Note: Continuing research r esu lts in steady impr ovements; ...

  • Taylor 428 - page 5

    1 Model 4 28 T o the I nstaller 131206 Section 1 T o the Installer The f ollowing infor mation has been inc luded in the manual as saf ety and regulat ory guidelines. F or complet e inst allation inst ruc tions, please see t he Inst allat ion Checklist . Installer Safety In all ar eas of t he world, equipment s hould be installed i n ac cordance wi ...

  • Taylor 428 - page 6

    2 Model 4 28 T o the I nstaller 080828 Electr ical Connectio ns This equipm ent is supplied wit h a 3-wire cord and grounding t ype plug, f or connec tion t o a s ingle phase, 60 cycle, branch circuit s upply . T his unit must be plugged into a pr operly grounded r ecept acle. T he cor d and plug provided ar e 20 A for 1 15/60/ 1, or 15 A f or 208- ...

  • Taylor 428 - page 7

    3 Model 4 28 T o the I nstaller 130923 Appliances t hat are perm anently c onnected t o fix ed wiring and for which leak age current s may exceed 10 mA, part icularly when disc onnect ed or not used for long periods, or during init ial installat ion, shall have prot ect ive devices suc h as a G FI , to prot ect against the leakage of current, insta ...

  • Taylor 428 - page 8

    4 Model 4 28 T o the O perator 131206 Sec tion 2 T o the O perator The f reezer you have purchased has been carefully engineered and manuf act ured to giv e y ou dependable operat ion. T he T aylor M odel 428, when properly operat ed and cared f or , will pr oduce a cons istent quality pr oduct . Like all m echanical pr oducts , t hey will require ...

  • Taylor 428 - page 9

    5 Model 4 28 Safety 130415 Se cti on 3 Sa fety We, at T aylor Company , are conc erned about t he safet y of the oper ator when he or she com es in cont act with t he fr eezer and its parts . T aylor has gone to extr eme effor ts t o design and manuf actur e built- in saf ety f eatur es t o protec t bot h you and the service technic ian. A s an exa ...

  • Taylor 428 - page 10

    6 Model 4 28 Safety 130415 S DO NOT allow unt rained pers onnel to operat e this m achine. S DO NOT operat e t he freez er unless all serv ice panels and access doors ar e restrain ed with screws. S DO NOT rem ove any int ernal oper ating part s (examples: f reez er door , beater, scr aper blades, et c.) unles s all contr ol switc hes are in t he O ...

  • Taylor 428 - page 11

    7 Mo del 428 Op erato r Parts I den ti fi catio n 101 101 Section 4 Operator Parts Identif ication Model 428 Figur e 1 ITE M DESCRIPTI ON PART NO. 1 LENS-LI GHT 052952 2 PLATE A.- DEC LIGHTED X52936 3 FIL TE R-A IR-1 7 X 1 3 X 7/1 6 052951 4 PANEL A.- SIDE*LEFT X62592 5 COVER A.- HOPPER X51152 6 TUBE-FEED 5/ 16 HOLE SS 028967-7 7 PANEL-REAR 062594 ...

  • Taylor 428 - page 12

    8 Model 4 28 Op erato r Parts I den ti fi catio n 120614 Beater Door Assembly With Standard D oor (N o Pr im e Plug) Figur e 2 ...

  • Taylor 428 - page 13

    9 Mo del 428 Op erato r Parts I den ti fi catio n 120614 Beater Door Assem bly With Standard Door (No Prim e Plug) ITE M DESCRIPTI ON PART NO. 1 PIN A. -VALVE HANDLE X25929 2 VALVE-DRAW SLUSH 047734 3 O-RI NG-1”OD X . 139W 032504 4 HANDLE A.- DRAW-SLUSH-BLK X47384 5 NUT-STUD 029880 6 DOOR A.- PARTIAL X39248-SER 7 BUSTER-I CE 047735 8 O-RI NG-.291 ...

  • Taylor 428 - page 14

    10 Model 4 28 Op erato r Parts I den ti fi catio n 120614 Beater Door Assembly With S elf - Closing/Pr im e Plug D oor Figur e 3 ...

  • Taylor 428 - page 15

    11 Mo del 428 Op erato r Parts I den ti fi catio n 120614 Beater Door Assembly With Self - Closin g/Prim e Plug Door ITE M DESCRIPTI ON P ART NO. 1 CAP A. - SPRING- RET AINER X54755 2 SPRING- COMP .970X.082X3. 875 030344 3 PLUNGER- CAP DRAW SWITCH 080554 4 PIN- HANDLE - V AL VE 064864 5 V AL VE- DRAW- SLUSH 080662 6 O- RING - 1” OD X .139 W 03250 ...

  • Taylor 428 - page 16

    12 Mode l 428 Op erato r Parts I den ti fi cati on 140718 Accessories Figur e 4 ITE M DESCRIPTI ON P ART NO. 1 KIT A. -TUNE UP X50413 2 BRUSH-MI X PUMP BODY-3”X7” 023316 3 BRUSH-DOUBLE ENDED 013072 4 BRUSH-REAR BRG 1I N.DX2IN 013071 5 BRUSH-DRAW VALVE 1X2X17 013073 ITE M DESCRIPTI ON P ART NO. 6 BRUSH- SYRUP PORT 045079 7 PAIL- 10 QT. 013163 8 ...

  • Taylor 428 - page 17

    13 Model 42 8 Impor tant: T o the Opera tor 081002 Section 5 Important: T o the Operator Figur e 5 ITE M DESCRIPTI ON P ART NO. 1 SWITCH- ROCKER AUT O/ W ASH (POWER SWITCH) 048420 2 SWITCH- TOGGLE- SPST 3/4 HP/250V ( DISPLA Y LIGHT) 012626 3 BUSHING A.- TORQUE (VI SCOSITY ADJUSTMENT) X50399 - SER 4 LIGHT- AMBER - RECT - 12VDC ADD MIX 052486- 02 ITE ...

  • Taylor 428 - page 18

    14 Model 4 28 Importa nt: T o the Oper ator 080313 Power Switch The cent er pos ition is OF F . The r ight position is AUTO, which act ivat es the beat er motor and the refr igerat ion system. The left position is W ASH, which activa tes t he beater m otor only . Display Ligh t Switch The display light s witch is located under t he cont rol channel ...

  • Taylor 428 - page 19

    15 Model 4 28 Operati ng P roced ures Section 6 Operating Procedures The M odel 428 freez er is des igned to pr oduce shak e or slush product at t he desired thic kness . This unit has a 7 quart f reezing c ylinder . We begin our inst ruct ions at the point where we enter the st ore in t he morning and f ind the par ts disassem bled and laid out t ...

  • Taylor 428 - page 20

    16 Model 4 28 Op erati ng Pro ced ures Step 3 Inser t the dr ive shaf t into the rear shell bearing and engage the squar e end firmly into t he female sock et of the dri ve unit. Be c ertain that the drive shaf t fit s int o the drive c oupling without binding. Figur e 10 Step 4 Check sc raper blades for any nic ks or signs of wear . If any nick s ...

  • Taylor 428 - page 21

    17 Model 4 28 Operati ng P roced ures 120418 Step 7 Inser t t he tor que rot or end with t he guide bear ing into the pilot hole in the cent er of the driv e shaf t. The hole in the t orque rot or shaf t should be r otat ed to the 12 o’clock pos ition. Figur e 14 Freezer Door Assembly - Standard Door (N o Prime Pl ug ) Note : The Mode l 428 c ome ...

  • Taylor 428 - page 22

    18 Model 4 28 Op erati ng Pro ced ures Step 12 Wit h the ic e bus ter in plac e, rot at e t he draw valv e to allow installat ion of the draw handle. This will loc k the ice bust er in place. Ins tall t he draw handle pin, and close t he draw valv e by mov ing the handle to the lef t. Figur e 19 Step 13 Place t he large rubber gasket int o the groo ...

  • Taylor 428 - page 23

    19 Model 4 28 Operati ng P roced ures Step B - Sel f - Cl osi ng Do o r Assembly Inser t t he draw valv e into t he door . Figur e 23 Step C - Sel f - Cl osi ng Do o r Assembly Ro tate the d raw va lve so th e gro ove o n th e top of the draw valv e is perpendicular t o the door f ace. Figur e 24 Step D - Sel f - Cl osi ng Do o r Assembly Ins ert t ...

  • Taylor 428 - page 24

    20 Model 4 28 Op erati ng Pro ced ures Step G - S elf - Clo sin g Do or Assembl y Place t he o - ring ont o the pr ime plug and lubricat e. Figur e 28 Step H - Sel f - Cl osi ng Do o r Assembly Scr ew the prim e plug into pos ition on t he front of t he door . Figur e 29 Step I - S elf - Clo sin g Do or Assembl y Place t he large rubber gasket int ...

  • Taylor 428 - page 25

    21 Model 4 28 Operati ng P roced ures 050415 Step L - S elf - Clo sin g Do or Assembl y Posit ion the t orque ar m by inser ting it down int o the hole on the t orque rot or whic h protr udes f rom t he door . V erif y proper installat ion by mov ing the tor que rot or back and f ort h to be s ure it m oves f reely . Figur e 33 Pro ceed to Step 16. ...

  • Taylor 428 - page 26

    22 Mode l 428 Op erati ng P roced ures 140718 Sani tizing Step 1 Prepar e a 2- 1/2 gallon ( 9.5 lit er) pail of cleaning/s anitiz ing solution wit h an act ive chlor ine concent rat e of 100 - 200 PPM (par ts per m illion). USE W ARM W A TER AND FOLLOW THE MANUF ACTURER ’S SPECIFICA T IONS. Step 2 Pour t he sanit izing solut ion into t he hopper ...

  • Taylor 428 - page 27

    23 Mode l 428 Operati ng P roced ures 050415 Pr iming the Freezing Cylinder Step 1 Wit h a pail beneath the door spout, mov e the draw handle to t he right . Pour t wo gallons ( 7.6 liters ) of FRE SH mix int o t he hopper and allow it to flow into the fr eezing cylinder . T his will for ce out any remaining sanitiz ing solut ion. W hen full s tren ...

  • Taylor 428 - page 28

    24 Mode l 428 Op erati ng P roced ures 140718 Step 5 Place t he mix hopper c over in posit ion. For pr oper operat ion, t here must be a substant ial amount of mix in the hopper . If the A DD MIX light illum inates, ref ill the mix hopper as soon as poss ible. Figur e 44 Closing P rocedur e T o disass emble this unit , t he following items will be ...

  • Taylor 428 - page 29

    25 Model 4 28 Operati ng P roced ures 080428 Rinsing Step 1 Pour two gallons (7. 6 liter s) of cool, clean water into the mix hopper . W ith the brushes provided, s crub the mix hopper , float s witc h, and the mix inlet hole. Figur e 45 Step 2 Wit h a pail beneath t he door s pout, place the power switc h in the WASH posit ion and move t he draw h ...

  • Taylor 428 - page 30

    26 Model 4 28 Op erati ng Pro ced ures 080313 Disassem bly BE SU RE TH E POWER SWITC H IS IN THE OFF POSI TION. F ailure to f ollow t his instr uct ion may res ult in s evere pers onal injury f rom hazardous mov ing part s. Step 1 Remove t he tor que arm, hands crews , f reezer door , tor que rotor , beat er ass embly , scraper blades and drive s h ...

  • Taylor 428 - page 31

    27 Model 4 28 Impor tant: Ope rator C heck list 051207 Section 7 Important: Operator Checklist Dur ing Cl eaning and Sa nitizi ng: AL W A YS FOLLOW LOCAL HEAL TH CODES Clean in g and san i tiz in g sched u les are go verned by fed eral, state, o r lo cal reg ul ato ry agen cies, an d must b e fo ll ow ed acco rdi ng ly . I f th e un it h as a “St ...

  • Taylor 428 - page 32

    28 Model 4 28 Importa nt: Oper ator Che cklis t Winter Stor age If the plac e of bus iness is t o be closed dur ing the wint er mont hs, it is import ant to prot ect the freezer by following cert ain prec autions, par tic ularly if t he building is t o be left unheat ed and subject to f reez ing conditi ons. Dis connect t he fr eezer f rom t he mai ...

  • Taylor 428 - page 33

    29 Model 4 28 T rouble shooting Guide Section 8 T roubleshooting Guide PROBL EM PROBABLE CAUSE REMEDY PA G E REF . 1. No product being dispensed. a. Power s witc h is in the OF F posit ion. a. Place power s witch in t he AUTO posit ion. 23 b. Im proper m ixing of product . b. Caref ully f ollow direct ions for m ixing produc t. --- c. I nadequate m ...

  • Taylor 428 - page 34

    30 Model 4 28 T rouble shooting Guide PROBL EM PROBABLE CAUSE REMEDY PA G E REF . 4. Product t oo thic k. a. Inadequate mix in hopper. a. Fill hopper wit h mix. 24 b. Im proper m ixing of product . b. Caref ully f ollow direct ions for m ixing produc t. --- c. T he visc osity adjus tment is set in correctly . c. Adjust the viscosity contr ol. 13 d. ...

  • Taylor 428 - page 35

    31 Mo del 428 Parts Rep lacemen t S ched ul e Section 9 Parts Replacement Schedule P ART DESCRIPTION EVER Y 3 MONTHS EVERY 6 MONTHS ANNUALL Y QUANTITIES TO BE REPLACED Drive S haft Seal X 1 Drive Shaf t O -Ring X 1 Scr aper Blade X 1 Fr eezer Door Gas ket X 1 Fr ont Bearing X 1 Draw V alve O-Rings X 2 Black Br ist le Brush - 1” x 2” Inspect &am ...

  • Taylor 428 - page 36

    32 Model 4 28 Limite d War ranty on Equipm ent 131206 Section 10 Limited Warranty on Equipment T A YL OR CO MP ANY LI MI TED WARRANTY O N FREE ZERS T aylor Com pany , a division of Carr ier Comm ercial Ref rigerat ion, I nc. (“ T aylor” ) is pleas ed to prov ide this limit ed warrant y on new T ay lor-branded f reez er equipment av ailable from ...

  • Taylor 428 - page 37

    33 Model 4 28 Limite d War ranty on Equipm ent 3. Replacement of wear items designat ed as Class “000” part s in the T aylor O perat or ’s Manual. 4. Ext ernal hoses , elec tric al power supplies , and mac hine grounding. 5. Part s not supplied or designat ed by T aylor , or dam ages result ing from t heir use. 6. Retur n trips or wait ing ti ...

  • Taylor 428 - page 38

    34 Model 4 28 Li mit ed Warran ty on Part s 131206 Section 1 1 Limited Warranty on Parts T A YL OR CO MP ANY LI MI TED WARRANTY O N T A YL OR G ENUINE P ARTS T aylor Com pany , a division of Carr ier Comm ercial Ref rigerat ion, I nc. (“ T aylor” ) is pleas ed to prov ide this limit ed warrant y on new T ay lor genuine replacem ent c omponents ...

  • Taylor 428 - page 39

    35 Model 4 28 Li mit ed Warran ty on Part s LI MI TED WARRANTY EX CEPT IO NS This limit ed warrant y does not cover: 1. Labor or other cos ts inc urred for diagnos ing, repair ing, remov ing, inst alling, shipping, servicing or handling of defec tive Part s, r eplacement Par ts , or new P art s. 2. Normal m aintenance, cleaning and lubricat ion as ...

  • Taylor 428 - page 40

    36 Model 4 28 Li mit ed Warran ty on Part s LI MI T A TI ON O F WARRANTY THI S L IMI TE D W ARRANT Y I S EXCL USI VE AND I S I N LI EU OF ALL O THE R W ARRANT IES , CO NDIT IO NS AND/O R REMEDI ES UNDER T HE LA W, INCLUDI NG ANY I MPL IE D W ARRANTI ES O R CONDI TI ONS O F MERCHANT ABIL I TY O R FI T NESS F OR A P ARTI CULAR P URPOS E. T HE ORI G I ...

  • Taylor 428 - page 41

    428 062598-12 11/13/13 GRN/YEL WHT BLK BLK BLK GROUND FRAME SECURELY M T2 COMPRESSOR L2 L1 T1 COMPRESSOR CONTACTOR CONDENSER FAN MOTOR BEATER MOTOR OVERLOAD SWITCH COMPRESSOR HIGH PRESSURE LIMIT SWITCH (SEE FIG 1) BLK BLK COMPRESSOR CONTACTOR BLK WHT WHT M BLK BLK WHT WHT L1 AUTO WASH OFF AUTO WASH OFF BLK POWER SWITCH BLK BLK BLU M BEATER MOTOR L2 ...

  • Taylor 428 - page 42

    428 062598-40 11/13/13 GRN/YEL BLU BRN BLK BLK BLK GROUND FRAME SECURELY M T2 COMPRESSOR L2 L1 T1 COMPRESSOR CONTACTOR CONDENSER FAN MOTOR BEATER MOTOR OVERLOAD SWITCH COMPRESSOR HIGH PRESSURE LIMIT SWITCH (SEE FIG 1) BLK BLK COMPRESSOR CONTACTOR BLK WHT WHT M BLK BLK WHT WHT L1 L1 N AUTO WASH OFF AUTO WASH OFF BLK POWER SWITCH BLK BLK BLU M BEATER ...

Manufacturer Taylor Category Refrigerator

Documents that we receive from a manufacturer of a Taylor 428 can be divided into several groups. They are, among others:
- Taylor technical drawings
- 428 manuals
- Taylor product data sheets
- information booklets
- or energy labels Taylor 428
All of them are important, but the most important information from the point of view of use of the device are in the user manual Taylor 428.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Taylor 428, service manual, brief instructions and user manuals Taylor 428. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Taylor 428.

Similar manuals

A complete manual for the device Taylor 428, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Taylor 428 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Taylor 428.

A complete Taylor manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Taylor 428 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Taylor 428, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Taylor 428, that we can find in the current document
3. Tips how to use the basic functions of the device Taylor 428 - which should help us in our first steps of using Taylor 428
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Taylor 428
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Taylor 428 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Taylor 428?

Use the form below

If you did not solve your problem by using a manual Taylor 428, ask a question using the form below. If a user had a similar problem with Taylor 428 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)