English dropdown-ico

Manual Cisco Systems IE20004TSB

110 pages 7.73 mb
Download

Go to site of 110

Summary
  • Cisco Systems IE20004TSB - page 1

    Americas Headquarters Cisco Systems, In c. 170 West Tasman Drive San Jose, CA 951 34-1706 USA http://www.ci sco.com Tel: 408 526-4000 800 553-NETS (638 7) Fax: 408 527-0883 Cisco IE 20 0 0 S witc h Hardw are Installation Guide June 20 13 Text Part Number: OL -25818-04 ...

  • Cisco Systems IE20004TSB - page 2

    THE SPECIFICATION S AND INFORMATION REGARDING TH E PRODUCTS IN THIS MANUAL ARE SUBJECT T O CHANGE WITH OUT NOTICE. ALL STATEMENTS , INFORMATION , AND RECOMMEN DATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESEN TED WITHOUT WARRANTY OF ANY KIND, EX PRESS OR IMPLIED. USERS MUST TAKE FULL RESPO NSIBILITY FOR THEIR APPLICAT ION OF ANY PRO ...

  • Cisco Systems IE20004TSB - page 3

    iii Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 CONTENTS Preface vii Audience vii Purpose vii Conventi ons vii Related Publica tions viii Obtaining Documentation, Obtaining Support, and Se curity Guidelines viii CHAPTER 1 Product Overview 1-1 Switch Mode ls 1-2 Front Panel 1-5 10/100BAS E-T Downlink Ports 1-8 Power over Ethernet Po ...

  • Cisco Systems IE20004TSB - page 4

    Contents iv Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Management Options 1-2 1 Network Configurations 1-22 CHAPTER 2 Switch Installation 2-1 Preparing for Installation 2-1 Warnings 2-1 Additional Information for Installa tion in a Hazardous Environme nt 2-3 Hazardous Area Installation Warnings 2-3 North American Hazardous Locatio ...

  • Cisco Systems IE20004TSB - page 5

    Contents v Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Wiring the Protective Ground and DC Power for Alarm Circuits 2-34 Wiring the External Alarms 2-35 Attaching the Alarm Connector to the Switch 2-38 Connecting Destination Po rts 2-39 Connecting to 10/100 and 10/100/1000 Ports 2-40 Installing and Removing SFP Mo dules 2-42 Instal ...

  • Cisco Systems IE20004TSB - page 6

    Contents vi Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Hazardous Locations Standards A-6 APPENDIX B Cable and Connectors B-1 Connector Specificatio ns B-1 10/100 Ports B-1 SFP Module Connecto rs B-2 Dual-Purpose Ports B-2 Console P ort B-2 Alarm Port B-3 Cables and Adapters B-4 SFP Modu le Cables B-4 Cable Pinouts B-7 Console Port ...

  • Cisco Systems IE20004TSB - page 7

    vii Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Preface Audience This guide is for the networ king or computer tech ni cian responsible for i nstalling Cis co IE 2000 series switches. W e assume that you are fami liar with the concepts and termi nology of Ethernet and local area networking. Purpose This guide documents the hardware ...

  • Cisco Systems IE20004TSB - page 8

    viii Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter War ni ng This warning symbol means dan ger . Y ou are in a situatio n that could cause bodily injury . Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be fami liar with standard practices for preventing accidents. Use the stat ...

  • Cisco Systems IE20004TSB - page 9

    CH A P T E R 1-1 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 1 Product Overview This switch provides a rugged and secure switching infrastructure for ha rsh en vironments. It is suitable for industrial Ethernet applicati ons, including fa ctory automation, int elligent transportation systems (ITSs), substation s, oil and ga s insta ...

  • Cisco Systems IE20004TSB - page 10

    1-2 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Switch Models Switch Models Ta b l e 1 - 1 lists and describes the switch models. T a ble 1 -1 Switc h Descr iptio ns Model Description Software Image Cisco IE-2000-4T -L 4 10/100BASE-T do wnlink ports 2 10/100B ASE-T upli nk ports LAN Lite Cisco IE-2000-4T ...

  • Cisco Systems IE20004TSB - page 11

    1-3 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Product Overvie w Switch Models Cisco IE-2000-16TC-L 16 10/100B ASE- T dow nlink ports, 2 Fast Ethern et dual-purpose uplin k ports 2 100 Mb/s SFP module uplin k slots LAN Lite Cisco IE-2000-16TC-B 16 10/100B A SE-T do wnlink ports 2 Fast Ethern et dual-purpose uplin k ports ...

  • Cisco Systems IE20004TSB - page 12

    1-4 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Switch Models Cisco IE-2000- 16PTC-G-L 12 10/100 B ASE-T do wnlink ports 2 Gigabit Ethernet d ual-purpose uplink po rts 4 Po wer ove r Ethernet (PoE) ports Note The four PoE ports can operate as PoE or as PoE+ if suff icient ex ternal power source is pro vi ...

  • Cisco Systems IE20004TSB - page 13

    1-5 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Product Overvie w Front Panel Front Panel This section describes the fro nt panel components. See Ta b l e 1 - 1 . • 10/100B ASE-T Ethernet p orts • 10/100/1000 upli nk ports (a v ailable on some models). • Dual-purpose ports (av ail able on some mod els). • SFP modu ...

  • Cisco Systems IE20004TSB - page 14

    1-6 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Front Pan el Figure 1 -2 Cisco IE-200 0-8TC-L Front P anel 3 USB mini-T ype B (console) port 8 Protecti ve gro und connection 4 RJ-45 console p ort 9 Flash memory card slot 5 Power connector DC-A 1 10/100 Ethernet ports (d ownl ink ports) 6 Po wer connector ...

  • Cisco Systems IE20004TSB - page 15

    1-7 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Product Overvie w Front Panel Figure 1 -3 Cisco I E-20 00 -1 6TC-L Front P ane l View 1 10/100 Ethernet ports (d ownl ink ports) 6 Po wer connector DC-B 2 Dual-purpose p orts (uplink ports) 7 Alarm conn ector 3 USB mini-T ype B (console) port 8 Protecti ve gro und connection ...

  • Cisco Systems IE20004TSB - page 16

    1-8 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Front Pan el Figure 1 -4 Cisco IE-2 00 0-1 6PTC-G -E Switc h Fr ont P anel V iew 10/100BASE-T Downlink Ports Y ou can set the 10/10 0B ASE-T do wnlink ports to operate at 10 or 100 Mb/s in full-duple x or half-dupl ex mode. Y ou can also set these ports for ...

  • Cisco Systems IE20004TSB - page 17

    1-9 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Product Overvie w Front Panel You can use the mdix au to interf ace confi guration command in the co mmand-line interf ace (CLI) to enable the automatic medi um-dependent interface crossov er (a uto-MDIX) feature. When the auto- MDIX feature is enabled, the switch detects th ...

  • Cisco Systems IE20004TSB - page 18

    1-10 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Front Pan el By default, the switch selects the medium for each dual-purpose port (10/100B A SE-T or SFP). When a link is achie v ed on one media type, the swit ch disa bles the other media t ype until the acti v e link goes down. If l inks are acti ve on ...

  • Cisco Systems IE20004TSB - page 19

    1-11 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Product Overvie w Front Panel For the most up-to-dat e list of supported SFP mode ls for Cisco Industrial Ethernet switches, see http://www .cisco.com/en/ US/docs/interfaces_m odule s/transcei v er_modules/compatibi lity/matrix/OL_ 6981.html#wp13 8176 For installation instr ...

  • Cisco Systems IE20004TSB - page 20

    1-12 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Front Pan el Figur e 1 -5 P ow er Connect or The switch can operate with a single po wer source or with dual power so urces. When both po wer sources are operational, the switch draws power from t he DC source with the higher v oltage. If one of the tw o p ...

  • Cisco Systems IE20004TSB - page 21

    1-13 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Product Overvie w Front Panel Management Ports Y ou can connect the switch to a PC run ning Microsoft W indo ws or to a terminal server th rough either the RJ-45 console port or the USB mini-T ype B consol e port, also refe rred to as the USB -mini console port. These ports ...

  • Cisco Systems IE20004TSB - page 22

    1-14 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Front Pan el LEDs Y ou can use the LEDs to monito r the switch status, acti vity , and performance. Figure 1-8 and Figure 1- 9 sho w the front panel LEDs. Figur e 1 -8 LEDs on the Cisco IE 20 00 Switch Note On IE 2000 switch es with PoE suppor t, the two S ...

  • Cisco Systems IE20004TSB - page 23

    1-15 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Product Overvie w Front Panel Express Setup LED The Express Setup LED displays the express setup mode for the init ial configurati on. Ta b l e 1 - 3 lists the LED colors and their meanings. System LED The System LED sho ws whether th e system is recei ving po wer and is fu ...

  • Cisco Systems IE20004TSB - page 24

    1-16 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Front Pan el Alarm LEDs Ta b l e 1 - 6 and Ta b l e 1 - 7 list the alarm LED colors and their meanings. Power Status LEDs The switch can operate wit h one or two DC po wer so urces. Each DC input has an associated LED that sho ws the status of the correspo ...

  • Cisco Systems IE20004TSB - page 25

    1-17 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Product Overvie w Front Panel Port Status LEDs Each 10/100B ASE-T do wnlin k port, 10/100B AS E-T uplink port, 10/100/ 1000B ASE-T uplink p ort, dual-purpose uplink port, and SFP Modu le uplink slot has a port st atus LED, also called a port LED, as sho wn in Figure 1-8 and ...

  • Cisco Systems IE20004TSB - page 26

    1-18 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Front Pan el Dual-Purpose Port LEDs Figure 1-9 sho ws the LEDs on a d ual-purpose port. Y ou can conf igure each port as either a 10/100/1000B ASE-T port thro ugh the RJ-45 connec tor or as an SFP module, b u t not both at the same time. The LEDs sho w how ...

  • Cisco Systems IE20004TSB - page 27

    1-19 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Product Overvie w Front Panel PoE Status LED The PoE ST A TUS LED is loca ted on the front panel of the IE 2000 switch models that are equipped with PoE ports.The LED displa ys the functionality and stat us of the PoE ports. The LED colors and meanings are listed in Ta b l ...

  • Cisco Systems IE20004TSB - page 28

    1-20 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Front Pan el Figur e 1 -1 0 Flash Memory Car d Slot Note The replacement SD card part number is SD-IE-1GB . 331548 16TC ±12/24/48 0.5-3.0A ...

  • Cisco Systems IE20004TSB - page 29

    1-21 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Product Overvie w Rear Panel Rear Panel The rear panel of the switch has a latc h for installation on a DIN rail. See Figure 1- 11 . The latch is spring-loaded to mov e do wn to position the switch ov er a DIN rail and return to the ori ginal position to secure the switch t ...

  • Cisco Systems IE20004TSB - page 30

    1-22 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 1 Prod uct Overview Network Configurations • Cisco IOS CLI The switch CLI is based on Cisc o IOS software and is en hanced to support desktop-switch ing features. Y ou can fully configure and monitor the switch. Y ou can access the CLI either by connecting your management s ...

  • Cisco Systems IE20004TSB - page 31

    CH A P T E R 2-1 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 2 Switch Installation This chapter describes ho w to install your switch, ve rify the boot f ast, and connect the switch to other devices. It also in cludes information specif ically for instal lations in hazardous en v ironments. Read these topics, and perform the proced ...

  • Cisco Systems IE20004TSB - page 32

    2-2 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Preparing for Installation War ni n g Do not work on the sy stem or connect or disconnect cables during periods of lightning a ctivity . Statement 1001 War ni n g Before performing any of th e following procedures, ensure that power is removed from the D ...

  • Cisco Systems IE20004TSB - page 33

    2-3 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Preparing for Installation Caution Airflo w around the switch must be unrestricted. T o pre vent the switch from ov erheating, ther e must be the follo wing minimum cl earances: – T op and bottom: 2 .0 in. (50.8 mm) – Sides: 2.0 in. (50.8 mm) – Fron ...

  • Cisco Systems IE20004TSB - page 34

    2-4 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Preparing for Installation War ni ng Do not connect or disconnect cables to the ports while power is applied to the switch or any device on the network because a n electrical arc can occu r . This could cause an explosion in hazardous location installati ...

  • Cisco Systems IE20004TSB - page 35

    2-5 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Preparing for Installation North American Hazar dous Location Approval The follo wing informati on applies when operating this equipment in hazardo us locations: EMC Environmental Conditions for Pr oducts Installed in the European Union This section appli ...

  • Cisco Systems IE20004TSB - page 36

    2-6 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Preparing for Installation • This equipme nt is consider ed Group 1, Cl ass A industrial equipment, according to IEC/CISPR Publication 11. W ithout appropriate precau tions, there may be pot ential dif fi culties ensuring electromagnetic compatib ility ...

  • Cisco Systems IE20004TSB - page 37

    2-7 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Installing or Removing the Flash Me mory Card (Optional) • Airflo w around the switch must be unrestricted. T o pre vent the switch from ov erheating, you must ha ve the follo wing minimu m clearances: – T op and bottom: 2.0 in. (50.8 mm) – Sides: 2 ...

  • Cisco Systems IE20004TSB - page 38

    2-8 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Installing or Removing the Fl ash Memory Card (Optional) T o install or replace the flash me mory card, follow these steps: Step 1 On the front of the swi tch, locate the door that protects the f lash memo ry card slot. Loosen the captive scre w at the t ...

  • Cisco Systems IE20004TSB - page 39

    2-9 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to a Console Port Figure 2-2 Removing the Flash Memory Card fr om the Switc h Step 2 Install or remov e the card: • T o install a card, sl ide it into the slot , and press it in until it clicks in place. The card is ke yed so that you cannot ...

  • Cisco Systems IE20004TSB - page 40

    2-10 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to a Con sole Port RJ-45 Console Port Step 1 Connect the RJ-45-to-DB-9 adapter cable to the 9-pi n serial port on the PC. See Figure 2-3 . Connect the other end of th e cable to the switch console port. Step 2 Start the ter minal-emulation pr ...

  • Cisco Systems IE20004TSB - page 41

    2-11 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to a Console Port USB Mini-Type B Console Port Step 1 If you are connecting the switch USB-mini console por t to a W indo ws-based PC for the f irst time, in stall a USB driv er . See Figure 2-5 and the f ollow ing sections for more inf ormati ...

  • Cisco Systems IE20004TSB - page 42

    2-12 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to a Con sole Port Step 3 Connect a USB cable to the PC USB port. Connect the ot her end of the cable to the swit ch mini-B (5-pin connector) USB-mini console port. See Figure 2-5 . Figur e 2-5 Connecting the USB-Mini Console Cable Step 4 Ide ...

  • Cisco Systems IE20004TSB - page 43

    2-13 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to Power Step 7 Config ure the baud rate and charact er format of the PC or termin al to match the con sole port characteristics: • 9600 baud • 8 data bits • 1 stop bit • No parity • None (flo w control) Step 8 Connect po wer to the ...

  • Cisco Systems IE20004TSB - page 44

    2-14 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to Power Installing the Power Converter on a DIN Rail, Wall, or Rack Adapter Y ou install the po wer con verter on a DIN rail, wa ll, or rack as you would a switch mo dule. War ni ng This equipment is suppl ied as “open type” equipment. I ...

  • Cisco Systems IE20004TSB - page 45

    2-15 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to Power Caution Use at least a 4 mm 2 conductor to connect to the e xternal grounding scre w . The ground lug is not supplied with the swit ch. Y ou can use one of the these opt ions: • Single ring termin al • T wo single ring termin als ...

  • Cisco Systems IE20004TSB - page 46

    2-16 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to Power Figure 2-7 Installing the Ground-Lug Scr ew (Single Ring T er minal) 1 Ground ca ble 16TC ±12/24/48 0.5-3.0A 1 331951 ...

  • Cisco Systems IE20004TSB - page 47

    2-17 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to Power Figur e 2-8 Installing the Grou nd-Lug Scr ews (T wo Single Ring T er minals) Step 7 Attach the other end of the ground wire to a grounded bare metal surface, such as a ground b us, a grounded DIN rai l, or a grounded bare rack. Conne ...

  • Cisco Systems IE20004TSB - page 48

    2-18 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to Power Note This section does not apply t o PWR-IE50W -AC-IEC, wh ich has pluggable IEC conn ector . Connecting the AC Power Source to the Power Converter Caution A C po wer sources must be dedi cated A C branch circ uits. Each branch circu ...

  • Cisco Systems IE20004TSB - page 49

    2-19 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to Power Step 4 Insert the line and neutral wire leads into the terminal block line and neutral co nnections. See Figure 2-9 , items 2 and 3. Make sure that you cannot s ee any wire lead. Ensure that only wire with in sulation extends from the ...

  • Cisco Systems IE20004TSB - page 50

    2-20 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to Power Figure 2-1 0 AC/DC Po w er Inpu t T erminal B lock Wir e Conn ections t o a DC Sour ce War ni ng An exposed wire lead from a DC-input power source can condu ct harmful levels of electricity . Be sure that no exposed po rtion of the D ...

  • Cisco Systems IE20004TSB - page 51

    2-21 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to Power War ni n g A readily accessible two-poled d isconnect device must be inc orporated in the fixed wiring. Statement 1022 War ni n g This product relies on the building’ s installation for short-circuit (overcurrent) protection. Ensure ...

  • Cisco Systems IE20004TSB - page 52

    2-22 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to Power The switch panel labels can be seen in Figure 1-1 , Figure 1-2 , or Figure 1-3 . Step 3 Measure two str ands of twisted-pair copper wire (18-to-2 0 A WG) long enough to con nect to the DC power source. Step 4 Using an 18-gauge wire-s ...

  • Cisco Systems IE20004TSB - page 53

    2-23 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to Power Step 6 On the po wer connector , insert the e xposed part of th e po siti ve wire into th e connection labeled “+” and the exposed part of the return wi re into the connection labeled “–”. See Figure 2-14 . M a k e s u r e t ...

  • Cisco Systems IE20004TSB - page 54

    2-24 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to Power Figur e 2-15 T orquing the P o w er Connect or Captiv e Scr ews Step 8 Connect the other end of the po sitiv e wire to the po sitiv e terminal on the DC po wer source, and connect the other end of the retu rn wire to the return termi ...

  • Cisco Systems IE20004TSB - page 55

    2-25 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to Power Figure 2-16 Completed DC P o wer Conn ections on the P ower Connect ors If your po wer source is –48 VDC, this table describes th e your wiring connecti ons for Figure 2-16 . Attaching the Power Connectors to the Switch T o attach t ...

  • Cisco Systems IE20004TSB - page 56

    2-26 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to Power Figur e 2-1 7 Attaching the P o wer Connect ors t o the Switc h 1 DC-A power connector 3 DC-B po wer connector 2 DC-A power connection 4 DC-B po wer connection 16TC ±12/24/48 0.5-3.0A 331213 3 4 1 2 ...

  • Cisco Systems IE20004TSB - page 57

    2-27 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to Power Figur e 2-18 Conne cting the P ow e r C on ne c tor s to t h e Sw it ch Step 2 Use a ratcheting torque flathead scre wdri v er to tighten the capti ve scre ws on the sid es of the po wer connectors. When you are testing the switch, on ...

  • Cisco Systems IE20004TSB - page 58

    2-28 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to Power Connecting Power to the Swit ch PoE DC-Input (Optional) This procedure is applicab le only to t he IE 2000 sw itch models that are PoE cap able. If you hav e a PoE capable IE 2000 switch and d o not plan on using PoE, you do not need ...

  • Cisco Systems IE20004TSB - page 59

    2-29 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting to Power T o attach source DC to the PoE DC-i nput connector , follo w these steps: Step 1 V erify that power is of f to the DC circuit that you are go ing to attach to t he switch PoE DC-input connector . This can be either of th e two po wer ...

  • Cisco Systems IE20004TSB - page 60

    2-30 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting to Power Applying Power to the Power Converter Mov e the circuit breaker for the A C outlet or the DC con trol circuit to the on position . The LED on the po wer con v erter front panel is green when the un it is operating normal ly . The LED ...

  • Cisco Systems IE20004TSB - page 61

    2-31 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Installing the Switch Verifying Boot Fast When you po wer on the switch, it automati cally begi ns a boot fast sequence. The System LED bli nks green as the Cisco IOS software image loads. If the bo ot f ast sequence fails, the System LED turns red. Note ...

  • Cisco Systems IE20004TSB - page 62

    2-32 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Installing the Switch Caution T o prev ent the switch fr om ov erheating, ensure th ese minimum cleara nces: – T op and bott om: 2.0 in. (50.8 mm) – Exposed si de (not connected to the modul e): 2.0 in. (50.8 mm) – Front: 2.0 in. (50 .8 mm) Instal ...

  • Cisco Systems IE20004TSB - page 63

    2-33 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Installing the Switch Step 3 Push the sw itch toward the DIN rail to cause the spring-l oaded latch at the botto m rear of the switch to mov e do wn, and snap into place. After the switch is mounted on the DIN rail, connect the power an d alarm wires, as ...

  • Cisco Systems IE20004TSB - page 64

    2-34 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting Alarm Circuits Figur e 2-20 Releasing the Spring-Loaded Latc h from the DIN Rail Step 4 Remov e the switch from the DIN rail. Connecting Alarm Circuits After the switch is inst alled, you are ready to connect the DC po wer an d alarm connecti ...

  • Cisco Systems IE20004TSB - page 65

    2-35 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting Alarm Circuits Wiring the External Alarms The switch has two alarm input and one alarm output relay circuits for external alarms. The alarm input circuits are designed to sense if the alarm input is open or closed re lati ve to the alarm in pu ...

  • Cisco Systems IE20004TSB - page 66

    2-36 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting Alarm Circuits Figure 2-21 Removing the Alar m Connecto r Step 2 Measure two st rands of twisted-pair wire (18-to- 20 A WG) long enough to con nec t to the external alarm de vice. Choose between setting up an exte rnal alarm input or output c ...

  • Cisco Systems IE20004TSB - page 67

    2-37 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting Alarm Circuits Figur e 2-22 Inserting Wir es into the Al ar m Connect or (Alar m Input Cir cuit) Step 5 Use a ratcheting torque flathead scre wdri ver to ti ghten the alarm connector capti ve scre w (abov e the installed w ire leads) to 2 in-l ...

  • Cisco Systems IE20004TSB - page 68

    2-38 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting Alarm Circuits Step 6 Repeat Step 2 throug h Step 5 to insert the i nput and output wires of one additi onal ex ternal alarm de vice into the alarm connector . Figure 2-24 sho ws the completed wir ing for two e xternal alarm de vices. The fir ...

  • Cisco Systems IE20004TSB - page 69

    2-39 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting Destination Ports T o attach the alarm connector to the front panel of the switch, follo w these steps: Step 1 Insert the alarm connector into the re ceptacle on the switch front panel. See Fig ure 2-25 . Figur e 2-25 Conne cting the Alar m C ...

  • Cisco Systems IE20004TSB - page 70

    2-40 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting Destination Por ts Connecting to 10/100 and 10/100/1000 Ports The switch 10/100/10 00 ports automatically co nfigur e themselves to operate at the speed of attached de vices. If the attach ed ports do not supp ort autone gotiation, you can e ...

  • Cisco Systems IE20004TSB - page 71

    2-41 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting Destination Ports Figur e 2-26 Connecting to an Ether net P ort Step 2 Connect the other end of the cabl e to an RJ-45 connector on the other de vice. The port LED t urns on when both the switch an d the connected de vice ha ve established a l ...

  • Cisco Systems IE20004TSB - page 72

    2-42 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting Destination Por ts Installing and Removing SFP Modules These sections describe ho w to install and remo ve SFP modules. S FP modules are inserted into SFP module slots on the front of the switch. These field-replaceable mo dules provide the u ...

  • Cisco Systems IE20004TSB - page 73

    2-43 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting Destination Ports Step 2 Find the send (TX) and recei ve (RX) markings th at identify the correct side of the SFP module. On some SFP modules, the send and recei ve (TX and RX ) markings might be repl aced by arro ws that sho w the direction o ...

  • Cisco Systems IE20004TSB - page 74

    2-44 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting Destination Por ts Step 4 Unlock and remov e the SFP module. If the module has a bale-clasp latch, pull the bale out and do wn to eject th e module. If the bale-clasp latch is obstructed and y ou cannot use your inde x fin ger to open it, use ...

  • Cisco Systems IE20004TSB - page 75

    2-45 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Connecting Destination Ports War ni n g Do not connect or disc onnect cables to the ports while power is applied to the switch or any device on the network because a n electrical arc can occur . This could cause an explosion in hazardous location install ...

  • Cisco Systems IE20004TSB - page 76

    2-46 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Connecting Destination Por ts Step 3 Insert the other cable end into a fiber- opt ic receptacle on a targ et de vice. Step 4 Observe the port status LED: • The LED turns green when the switch and the target device ha ve an established link. • The LE ...

  • Cisco Systems IE20004TSB - page 77

    2-47 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installation Verifying Switch Operation Figur e 2-31 Connecting to a Dual-Pur pose P ort Step 2 Connect the other end of the cabl e to the other de vice. By default, the swi tch detects whet her an RJ-45 connector or SFP module is connected to a dual-purpose port and ...

  • Cisco Systems IE20004TSB - page 78

    2-48 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 2 Switch Installatio n Where to Go Ne xt • Start the Cisco Network Assistant appl ication, whic h is described i n the Getting Started with Cisco Network Assistant guide. Using the GUI, you can conf igure an d monitor a switch cluster or an indi vidual switch. • Use the C ...

  • Cisco Systems IE20004TSB - page 79

    CH A P T E R 3-1 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 3 Troubleshooting This chapte r provid es these topi cs f or troubleshooting p roblems: • Diagnosing Problems, page 3- 1 • Ho w to Recov er Passw ords, page 3-5 • Finding the Switch Serial Number , page 3-6 Diagnosing Problems The switch LEDs pro vide troubleshootin ...

  • Cisco Systems IE20004TSB - page 80

    3-2 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 3 Troubleshooting Diagnosing Prob lems Switch LEDs Look at the port LEDs infor mation when troubl eshooting the switch . See the “LEDs” section on page 1-14 for a description of the LED colors and th eir meanings. Switch Connections Bad or Damaged Cable Always e xamine the ...

  • Cisco Systems IE20004TSB - page 81

    3-3 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 3 Troubleshooting Diagnosing Problems 10/100 and 10/100/100 0 Port Connections If a port appears to malf unction: • V erify the stat us of all ports. See T able 1-9 on page 1- 17 for descriptions of the LEDs and their meanings. • Use the show interfaces pri vileg ed EXEC c ...

  • Cisco Systems IE20004TSB - page 82

    3-4 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 3 Troubleshooting Diagnosing Prob lems Switch Performance Speed, Duplex, and Autonegotiation Port statistics that sho w a large amount of a lignment errors, frame check sequence (FCS), or late-collisions errors, might mean a speed o r duplex mismatch . A common issue occurs wh ...

  • Cisco Systems IE20004TSB - page 83

    3-5 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 3 Troubleshooting Resetting the Switch Resetting the Switch These are reasons why you might want to r eset the switch to the f actory default sett ings: • Y ou installed the switch in your network and cannot connect t o it because you assigned the wro ng IP address. • Y ou ...

  • Cisco Systems IE20004TSB - page 84

    3-6 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Chapter 3 Troubleshooting Finding the Swit ch Serial Numbe r Finding the Switch Serial Number If you contact Cisco T echnical Assistance, you need to kno w the serial number of your switch. The serial number is on the compliance label on the righ t-hand side of the switch. See Figure ...

  • Cisco Systems IE20004TSB - page 85

    A-1 Cisco IE 2000 Switch Hardwa re Installation Guide OL-25818-04 APPENDIX A Technical Specifications This appendix provides the technical sp ecification f or the Cisco IE 2000 switches. Operating Temperature Specifications Ta b l e A - 1 lists the operating temperatures f or the Cisco IE 2000 switches in three different en vironments. Note The saf ...

  • Cisco Systems IE20004TSB - page 86

    A-2 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix A Technical Specific ations Technical Specific ations Technical Specifications Ta b l e A - 2 lists the technical specif ications for the Cisco I E 2000 switches. T able A -2 Cisco IE 20 00 Ser ies T echn ical Specifications Environmental Ranges Storage temperature –40 to 1 ...

  • Cisco Systems IE20004TSB - page 87

    A-3 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix A T echnical Specifications Technical Specifications Po wer consumption 1 6-port model s—9.5 W (t ypical), 15 W (maximum) • Cisco IE-2000-4T -L • Cisco IE-2000-4T -B • Cisco IE-2000-4T -G-L • Cisco IE-2000-4T -G-B • Cisco IE-2000-4TS-L • Cisco IE-2000-4TS-B • ...

  • Cisco Systems IE20004TSB - page 88

    A-4 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix A Technical Specific ations Technical Specific ations Phy sical Dimensions W eight 6-port models—2.45 lbs (1 .11 kg) • Cisco IE-2000-4T -L • Cisco IE-2000-4T -B • Cisco IE-2000-4T -G-L • Cisco IE-2000-4T -G-B • Cisco IE-2000-4TS-L • Cisco IE-2000-4TS-B • Cisco ...

  • Cisco Systems IE20004TSB - page 89

    A-5 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix A T echnical Specifications Technical Specifications Dimensions 2 (H x W x D) 6-port models—5.1 0 x 2.95 x 4.29 in . (13.0 cm x 7.5 cm x 10.9 cm) • Cisco IE-2000-4T -L • Cisco IE-2000-4T -B • Cisco IE-2000-4T -G-L • Cisco IE-2000-4T -G-B • Cisco IE-2000-4TS-L • ...

  • Cisco Systems IE20004TSB - page 90

    A-6 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix A Technical Specific ations Alarm Ratings Alarm Ratings Ta b l e A - 3 lists the alarm ratings for the Cisco IE 2000 swi tches. Hazardous Locations Standards Ta b l e A - 4 lists the hazardous location standards fo r the Cisco IE 2000 switches. T able A -3 Alarm Input an d Ou ...

  • Cisco Systems IE20004TSB - page 91

    B-1 Cisco IE 2000 Switch Hardwa re Installation Guide OL-25818-04 APPENDIX B Cable and Connectors • Connector Specif ications, page B-1 • Cables and Adapt ers, page B-4 Connector Specifications • 10/100 Ports, page B-1 • SFP Module Connectors, page B-2 • Dual-Purpose Ports, page B-2 • Alarm Port, page B-3 10/100 Ports The 10/100 Etherne ...

  • Cisco Systems IE20004TSB - page 92

    B-2 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix B Cable and Connectors Connector Specifications SFP Module Connectors Figure B-2 sho ws a MT -RJ style connector that is used with the SFP Module slots. It is a fiber -optic cable connector . Figure B-2 Fiber -Optic SFP Module LC Co nnector War ni ng Invisible laser radiation ...

  • Cisco Systems IE20004TSB - page 93

    B-3 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix B Cable and Conne ctors Connector Specifications The USB console port uses a USB T ype A to 5-pin mini -T ype B cable, sho wn in Figure B-5 . T he USB T ype A-to-USB mini-T ype B cable is n o t s u pp l ie d . Y ou can order an accessory kit (part number 800-33434) that conta ...

  • Cisco Systems IE20004TSB - page 94

    B-4 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix B Cable and Connectors Cables and Adapters Cables and Adapters • SFP Module Cables, page B-4 • Cable Pinouts, page B-7 • Console Port Adapter Pinout s, page B-8 SFP Module Cables Each port must match the w av e-length specif icati ons on each end of the cable, and for r ...

  • Cisco Systems IE20004TSB - page 95

    B-5 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix B Cable and Conne ctors Cables and Adapters T able B-2 Fiber -Optic SFP Module P ort Cabling Specificatio ns T y pe of SFP Module Wavelength (nanometers) Fiber T ype Core Size/Cladding Size (micron) Modal Bandwidth (MHz/km) 1 Cable Distance Industrial and Rugged SFPs 1000B AS ...

  • Cisco Systems IE20004TSB - page 96

    B-6 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix B Cable and Connectors Cables and Adapters Note When the fiber -optic cable span is l ess than 15.43 miles (25 km), inser t a 5-decibel (dB) or 10-dB inli ne optical attenuator between the fi ber-optic cable plant and the recei ving port on the 1000B ASE-ZX SFP module. Extend ...

  • Cisco Systems IE20004TSB - page 97

    B-7 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix B Cable and Conne ctors Cables and Adapters Cable Pinouts Figure B-6 T wo T wisted-P air Straight-Through Cable Schematic for 1 0/ 1 0 0 Por ts Figure B-7 T wo T wisted-P air Cr ossov er Cable Schematic for 1 0/1 0 0 Por ts Figur e B-8 Four T wist ed-P a ir Straight-T hr ough ...

  • Cisco Systems IE20004TSB - page 98

    B-8 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix B Cable and Connectors Cables and Adapters Figur e B-9 F our T wisted-P air Crosso ver Cabl e Schematic s for 1 000BASE-T P or ts T o identify a crosso ver cable, hold the cable end s side-by-side, with the tab at the back. The wire connected t o pin 1 on the left end sho uld ...

  • Cisco Systems IE20004TSB - page 99

    B-9 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix B Cable and Conne ctors Cables and Adapters Ta b l e B - 3 lists the pinou ts for the console port, the RJ-45-to-DB-9 adap ter cable, and the console de vice. Ta b l e B - 4 lists the pinouts fo r the switch console port, RJ-45-to-DB-25 female DTE adapter , and the console de ...

  • Cisco Systems IE20004TSB - page 100

    B-10 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix B Cable and Connectors Cables and Adapters ...

  • Cisco Systems IE20004TSB - page 101

    C-1 Cisco IE 2000 Switch Hardwa re Installation Guide OL-25818-04 APPENDIX C Configuring the Switch with the CLI-Based Setup Program This appendix provides a command-line interface (CLI)-based setup proc edure for a switch. F or information about setti ng up the switch b y using Express Setup, see the Cisco I E 2000 Switc h Getting Started G uid e. ...

  • Cisco Systems IE20004TSB - page 102

    C-2 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix C Con figuring the Switch with the CLI-Based Setup Program Accessing the CLI Thr ough the Console Por t Figur e C-1 Removing the USB Mini -T ype B Console P ort Cov er RJ-45 Console Port Step 1 Connect the RJ-45-to-DB-9 adapter cable to th e 9-pin serial port on the PC. Conne ...

  • Cisco Systems IE20004TSB - page 103

    C-3 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix C Configuring the Switch with the CLI-Based Setup Pro gram Accessing the CLI Throug h the Console Port Figure C-2 Connecting the Consol e Cable Step 3 Config ure the baud rate and charact er format of the PC or termin al to match the con sole port characteristics: • 9600 ba ...

  • Cisco Systems IE20004TSB - page 104

    C-4 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix C Con figuring the Switch with the CLI-Based Setup Program Accessing the CLI Thr ough the Console Por t USB Mini-Type B Console Port Step 1 If you are connecting the switc h US B-mini console port to a W indo ws-b ased PC for the first time, in stall a USB driv er . See Figur ...

  • Cisco Systems IE20004TSB - page 105

    C-5 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix C Configuring the Switch with the CLI-Based Setup Pro gram Accessing the CLI Throug h the Console Port a. Choose Start > Contr ol P anel > Systems. b. Click the Hardwar e tab and choo se Device Manager . Expand the Po r ts section. The assigned COM port appears in paren ...

  • Cisco Systems IE20004TSB - page 106

    C-6 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix C Con figuring the Switch with the CLI-Based Setup Program Accessing the CLI Thr ough the Console Por t Step 5 Connect the USB cable to the PC and the switch c onsole port. The USB console port LED turns green, and the Found Ne w Hardwa re W izard appears. F ollow t h e instr ...

  • Cisco Systems IE20004TSB - page 107

    C-7 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix C Configuring the Switch with the CLI-Based Setup Pro gram Accessing the CLI Throug h the Console Port Uninstalling the Cisco Microsoft Windows USB Driver • Uninstalling the Cisco Microsoft W indows XP and 2000 USB D riv er • Uninstalling the Cisco Microsoft W indows V is ...

  • Cisco Systems IE20004TSB - page 108

    C-8 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix C Con figuring the Switch with the CLI-Based Setup Program Entering the Initial Con figuration Information Note If a User Account Control warnin g appears, click Allow - I trust this pr ogram to proceed . Step 5 When the InstallShield W izard Co mpleted windo w appears, click ...

  • Cisco Systems IE20004TSB - page 109

    C-9 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix C Configuring the Switch with the CLI-Based Setup Pro gram Entering the Initial Configuration Information Step 3 Enter an ena ble secret pa ssword, and pr ess Retur n . The password can be fro m 1 to 25 alphanumeric charac t ers, can start with a number , is case sensitive, a ...

  • Cisco Systems IE20004TSB - page 110

    C-10 Cisco IE 2000 Switch Hardware Installation Guide OL-25818-04 Appendix C Con figuring the Switch with the CLI-Based Setup Program Entering the Initial Con figuration Information interface FastEthernet1/1 ! interface FastEthernet1/2 ! interface FastEthernet1/3 ! ...(output abbreviated) ! interface GigabitEthernet1/1 ! interface GigabitEthernet1/ ...

Manufacturer Cisco Systems Category Switch

Documents that we receive from a manufacturer of a Cisco Systems IE20004TSB can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- IE20004TSB manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems IE20004TSB
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems IE20004TSB.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems IE20004TSB, service manual, brief instructions and user manuals Cisco Systems IE20004TSB. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems IE20004TSB.

Similar manuals

A complete manual for the device Cisco Systems IE20004TSB, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems IE20004TSB by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems IE20004TSB.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems IE20004TSB - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems IE20004TSB, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems IE20004TSB, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems IE20004TSB - which should help us in our first steps of using Cisco Systems IE20004TSB
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems IE20004TSB
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems IE20004TSB in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems IE20004TSB?

Use the form below

If you did not solve your problem by using a manual Cisco Systems IE20004TSB, ask a question using the form below. If a user had a similar problem with Cisco Systems IE20004TSB it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)