English dropdown-ico

Manual Cisco Systems OL-26646-01

124 pages 9.16 mb
Download

Go to site of 124

Summary
  • Cisco Systems OL-26646-01 - page 1

    Americas Headquarters Cisco Systems, In c. 170 West Tasman Drive San Jose, CA 951 34-1706 USA http://www.ci sco.com Tel: 408 526-4000 800 553-NETS (638 7) Fax: 408 527-0883 Cisco U CS C22 S erver Installation and S er vice Guide Covers S erver Generatio n M3 Febr uary 18, 20 1 4 Text Part Number: OL-26646-01 ...

  • Cisco Systems OL-26646-01 - page 2

    THE SPECIFICATION S AND INFORMATION REGARDING THE P RODUCTS IN TH IS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS , INFORMATION, AND RECOMMENDA TIONS IN THI S MANUAL ARE BE LIEVED TO BE A CCURATE BUT ARE PRESENTED WI THOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSI BILITY FOR THEIR APPLICATION OF ANY PROD ...

  • Cisco Systems OL-26646-01 - page 3

    iii Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 CONTENTS Preface vii Related Documentation vii Organization vii Audience viii Documentation Feedback viii Conventi ons viii Obtaining Documentation and Submitting a Serv ice Request xiii xiv CHAPTER 1 Overview 1-1 CHAPTER 2 Installing the Server 2-1 Unpacking and Inspecting the Se ...

  • Cisco Systems OL-26646-01 - page 4

    Contents iv Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Cisco Integrated Manageme nt Interface (Cisco IMC) 3-1 Server Configuration Utility 3-1 Status LEDs and Buttons 3-2 Front Panel LEDs 3-2 Rear Panel LEDs and Buttons 3-4 Preparing for Server Component Installation 3-6 Required Equipment 3-6 Shutting Down and Powering Off th ...

  • Cisco Systems OL-26646-01 - page 5

    Contents v Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Replacing the SuperCap Power Module (RAID Backup Unit) 3-41 Installing a Trusted Platform Mo dule 3-43 Enabling the In tel Trusted Execution Techn ology (TXT) Feature For the T PM 3-44 Replacing a SCU Upgrade ROM Module 3-46 Replacing a Software RAID Key Module 3-47 Replaci ...

  • Cisco Systems OL-26646-01 - page 6

    Contents vi Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Small Form Factor 8-Drive Backplane Cabling C-19 Large Form Factor 4-Drive Backpla ne Cabling C-21 Restoring RAID Configuration Af ter Replacin g a RAID Controller C-22 For More Information C-22 APPENDIX D Installation for Cisco UCS Integration D-1 ...

  • Cisco Systems OL-26646-01 - page 7

    vii Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Preface This preface describes the audi ence, organi zation, and conventions o f the Cisco UCS C22 Server Installation an d Service Guide . It al so provides information about h ow to obtain related docum entation. Related Documentation The documentation set for the Cisco Unified ...

  • Cisco Systems OL-26646-01 - page 8

    viii Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Preface Audience This guide is for experien ced network administra tors who configu re and maintain Cisco servers. Documentation Feedback T o provide technical feedback on this document, or to report an error or omissi on, please send your comments to ucs-docfeedback@external.cis ...

  • Cisco Systems OL-26646-01 - page 9

    ix Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Preface V aroitus TÄRKEITÄ TURVALLISUUSOHJEIT A Tämä varoitusmerkki merkitsee vaaraa. T ilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemisee n liittyvät riskit ja tutustu onnettomuuksien yl eisiin ehkäisytapoihi ...

  • Cisco Systems OL-26646-01 - page 10

    x Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Preface Avis o INSTRUÇÕES IMPORT ANTES DE SEGURANÇA Este símbolo de aviso significa perigo. V ocê está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conh ecimento dos perigos envolvidos no manus ...

  • Cisco Systems OL-26646-01 - page 11

    xi Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Preface Avis o INSTRUÇÕES IMPORT ANTES DE SEGURANÇA Este símbolo de aviso significa perigo. V ocê se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipam ento, esteja ciente dos riscos que envolvem os circuitos elétricos e ...

  • Cisco Systems OL-26646-01 - page 12

    xii Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Preface ...

  • Cisco Systems OL-26646-01 - page 13

    xiii Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Preface Obtaining Documentation and Submitting a Service Request For information on obtai ning documentation, using the Cisco Bug Search T ool (BST), submitting a service request, and gathering additional information, see What’ s New in Cisco Pr oduct Docum entation at: http:// ...

  • Cisco Systems OL-26646-01 - page 14

    xiv Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Preface ...

  • Cisco Systems OL-26646-01 - page 15

    CH A P T E R 1-1 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 1 Overview This chapter provi des an overview of th e Cisco UCS C22 server features. This server is a part of the Cisco UCS C-Series rack -mount server family . It is a high-performance, 1RU (rack-unit) server . It is designed to operate in both standalone environmen ...

  • Cisco Systems OL-26646-01 - page 16

    1-2 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 1 Overvi ew Figure 1-2 shows the front panel featur es of the larg e form-factor drives version of the server . Figure 1 -2 Cisco UCS C22 Server (Large F or m F actor Dr ives) F r ont Panel F eatur es 1 Power button/Power status LED 6 Power supply status LED 2 Identificati ...

  • Cisco Systems OL-26646-01 - page 17

    1-3 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 1 Overview Figure 1-3 shows the rear panel features of the server (identical for both versions of the server) . Figur e 1 -3 Rear P anel F eatur es Ta b l e 1 - 1 lists the features of the server . . 1 Power supply 6 Serial port (DB-9 connector) 2 PCIe slot 2 on riser 2 ( ...

  • Cisco Systems OL-26646-01 - page 18

    1-4 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 1 Overvi ew W oL The 1-Gb Base-T Ethernet LAN ports suppor t the wake-on-LAN (W oL) stand ard. Power One 450 W power supply or one 650W p ower supply . See also Power Specifications, page A- 2 . ACPI This server supports the advanced conf igu ration and power interface (AC ...

  • Cisco Systems OL-26646-01 - page 19

    CH A P T E R 2-1 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 2 Installing the Server This chapter d escribes how to in stall the server, and it includes the fo llowing sectio ns: • Unpacking and Inspecting t he Server , page 2-2 • Preparing for Server Installation, page 2-3 • Installing the Server In a Rack, page 2-5 • ...

  • Cisco Systems OL-26646-01 - page 20

    2-2 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 2 Installin g the Server Unpacking and Inspecting the Server Unpacking and Inspecting the Server Caution When handling internal server co mponents, wear an ESD strap and handl e modules by the carrier edges only . Ti p Keep the shipping container in case the server require ...

  • Cisco Systems OL-26646-01 - page 21

    2-3 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 2 Installing the Server Preparing for Serv er Installation Preparing for Server Installation This section prov ides information abou t preparing for server installation, and it includes the following topics: • Installation Guidelines, p age 2-3 • Rack Requirements, pa ...

  • Cisco Systems OL-26646-01 - page 22

    2-4 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 2 Installin g the Server Preparing for Server Installation Rack Requirements This section prov ides the requirem en ts for the stan dard open racks. The rack must be of the following type: • A standard 19-in. (48.3-cm) wide, fou r-post EIA rack, with mounting posts that ...

  • Cisco Systems OL-26646-01 - page 23

    2-5 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 2 Installing the Server Installing the Server In a Rack Installing the Server In a Rack This section describes how to install the server in a rack. War ni ng T o prevent bodily injury when m ounting or servicing this unit in a rack, you must take special precautions to en ...

  • Cisco Systems OL-26646-01 - page 24

    2-6 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 2 Installin g the Server Installing the Server In a Rack Step 2 Install the slide rails onto the rack: a. Position a slide-rail assembly inside the tw o left-side rack posts (see Figure 2-3 ). Use the “FRONT” and “REAR” markings on the slide- rail assembly to orien ...

  • Cisco Systems OL-26646-01 - page 25

    2-7 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 2 Installing the Server Installing the Server In a Rack b. Push the serv er into the slide rails unti l it stops at the internal stops. c. Push in the plastic release clip on each inner rail (labeled PUSH), and then con tinue pushing the server int o the rack until its fr ...

  • Cisco Systems OL-26646-01 - page 26

    2-8 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 2 Installin g the Server Initial Server Setup Initial Server Setup Connecting and Powering On the Server (Standalone Mode) Note This section describes ho w to po wer on the serv er , assign an IP address, and connect to server management when using the serv er in standal o ...

  • Cisco Systems OL-26646-01 - page 27

    2-9 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 2 Installing the Server Initial Server Setup Step 3 Open the Cisco IMC Conf iguration Util ity: a. Press the Pow e r button to boot the server . W atch for the promp t to press F8. b. During bootup, press F8 when prompted to open the Cisco IMC Configuration Utility . Not ...

  • Cisco Systems OL-26646-01 - page 28

    2-10 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 2 Installin g the Server Initial Server Setup b. Use this utility to change the NIC redundancy to your preference. This server has three possible NIC redundanc y settings: – None—The Ethernet ports operate independent ly and do not f ail ov er if there is a problem. ? ...

  • Cisco Systems OL-26646-01 - page 29

    2-11 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 2 Installing the Server Initial Server Setup Step 14 Press F5 to refresh the settings you made. Y ou might hav e to wai t about 45 seconds until the ne w settings appear and the message, Network settings conf igured is disp layed before you reboot the serv er in the next ...

  • Cisco Systems OL-26646-01 - page 30

    2-12 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 2 Installin g the Server NIC Modes and NIC Redundan cy Settings NIC Modes and NIC Redundancy Settings This server h as the follo wing NIC mode settings th at you can choose from: • Shared LOM EXT (default)—This is shared LOM extend ed mode. This is t he factory defaul ...

  • Cisco Systems OL-26646-01 - page 31

    2-13 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 2 Installing the Server System BIOS and Cisco IMC Firmware System BIOS and Cisco IMC Firmware This section includes inf ormation about the system BIOS an d it includes the foll owing sections: • Updating the BIOS and Cisco IMC Firmware, page 2-13 • Accessing the Syst ...

  • Cisco Systems OL-26646-01 - page 32

    2-14 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 2 Installin g the Server System BIOS and Cisco IMC Firmware Accessing the System BIOS T o change the BIOS settings for your server , follow these steps. Detailed instructions ar e also printed on the BIOS screens. Step 1 Enter the BIOS setup utility by pressing the F2 key ...

  • Cisco Systems OL-26646-01 - page 33

    2-15 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 2 Installing the Server Service He aders and Jump ers Service Headers and Jumpers This section includes the following topics: • Header Location on the Motherboard, page 2-15 • Using the BIOS Recovery Header CN 34, page 2-16 Header Location on the Motherboard See Figu ...

  • Cisco Systems OL-26646-01 - page 34

    2-16 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 2 Installin g the Server Service Headers a nd Jumpers Using the BIOS Recovery Header CN34 Depending on which stage t he BIOS becomes corrupted, you might see dif feren t behavior . • If the BIOS BootBlock is co rrupted, you might see the system get stuck on the followin ...

  • Cisco Systems OL-26646-01 - page 35

    2-17 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 2 Installing the Server Service He aders and Jump ers Note During the BIOS update, the Cisco IMC will shut down th e server and th e screen will be bl ank for about 10 minutes. Do no t unplug the power cords during t his update. The Cisco IMC will power on the server aft ...

  • Cisco Systems OL-26646-01 - page 36

    2-18 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 2 Installin g the Server Service Headers a nd Jumpers Procedure 2: Use Recovery Jumper and recovery.cap File See Figure 2-6 for the locati on of the CN34 header . Step 1 Download the BIOS update package an d extract it to a temp orary locati on. Step 2 Copy the contents o ...

  • Cisco Systems OL-26646-01 - page 37

    2-19 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 2 Installing the Server Service He aders and Jump ers ...

  • Cisco Systems OL-26646-01 - page 38

    2-20 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 2 Installin g the Server Service Headers a nd Jumpers ...

  • Cisco Systems OL-26646-01 - page 39

    CH A P T E R 3-1 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 3 Maintaining the Server This chapter describes how to diagnose server system problems using LEDs. It also provides i nformation about how to install or replace hardware co mponents, and it includes the foll owing sections: • Server Monitoring and M anagement T ool ...

  • Cisco Systems OL-26646-01 - page 40

    3-2 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Status LEDs an d Buttons Status LEDs and Buttons This section descri bes the location and meaning o f LEDs and buttons and incl udes the following topics: • Front Panel LEDs, page 3-2 • Rear Panel LEDs and Button s, page 3-4 Front Panel LEDs ...

  • Cisco Systems OL-26646-01 - page 41

    3-3 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Status LEDs and Button s System status • Green—The server is running in normal operating condition. • Green, blinking—The server is performi ng system initialization and memory check. • Amber , steady—The server is in a de gr aded oper ...

  • Cisco Systems OL-26646-01 - page 42

    3-4 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Status LEDs an d Buttons Rear Panel LEDs and Buttons Figure 3-2 shows the rear p anel LEDs and buttons. Ta b l e 3 - 2 defines the LED states. Figur e 3-2 Rear Panel LEDs and Butt ons 1 Power supply fau lt LED 5 10/100/1000 Ethernet dedicated man ...

  • Cisco Systems OL-26646-01 - page 43

    3-5 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Status LEDs and Button s 10/100/1000 Ether net dedicated management link status • Off—No l ink is present. • Green—Link is active. • Green, blinking—T raffic is present on the active link. Identif ication • Off—The Identification L ...

  • Cisco Systems OL-26646-01 - page 44

    3-6 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Preparing for Server Co mponent Installation Preparing for Server Component Installation This section descri bes how to prepare for component install ation, and it includes the followin g topics: • Required Equipment , page 3-6 • Shutting Dow ...

  • Cisco Systems OL-26646-01 - page 45

    3-7 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Preparing for Server Compone nt Installation Removing and Replacing the Server Top Cover T o remove or replace the top co ver of the server , follow these steps: Ti p Y ou do not have to remove the cover to replace hard d rives or the power supply ...

  • Cisco Systems OL-26646-01 - page 46

    3-8 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Preparing for Server Co mponent Installation Removing and Replacing the Front Chassis Panel T o remove or replace the front chassis panel of the server, follow these steps: Ti p Remove this panel only if you ar e instructed to do so in a p rocedu ...

  • Cisco Systems OL-26646-01 - page 47

    3-9 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Preparing for Server Compone nt Installation Replaceable Component Locations This section shows the lo cations of the componen ts that are discussed in this ch apter . The v iew in Figure 3-4 is from t he top down with the top cover , front chassi ...

  • Cisco Systems OL-26646-01 - page 48

    3-10 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Preparing for Server Co mponent Installation Color-Coded Touch Points This server has color -coded touch po ints that in dicate thumbscrews and latches on replaceable and hot-swappable com ponents. • Hot-swappable compon ents have green plasti ...

  • Cisco Systems OL-26646-01 - page 49

    3-11 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Installing or Replacing Server Components War ni ng Blank faceplates and c over panels serve three important functions: they prevent ex posure to hazardous voltages and currents inside the chassis; they ...

  • Cisco Systems OL-26646-01 - page 50

    3-12 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Replacing Hard Drives or Solid State Drives This section includes th e following information: • Drive Populatio n Guidelines, page 3-12 • Drive Replacement Procedure, page 3-12 Drive Population Guid ...

  • Cisco Systems OL-26646-01 - page 51

    3-13 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents c. If you are r eplacing an existing drive, remove the fo ur dri ve-tray screws that secure the drive to the tray and then lift t he drive out of the tray . Step 2 Install a new drive: a. Place a new dri ...

  • Cisco Systems OL-26646-01 - page 52

    3-14 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components c. Remove the top cover as described in “Removing and Replacing the Serv er T op Co ver” section on page 3-7 . d. Remove the front chassi s panel as described in Removing and Rep lacing the Front Ch ...

  • Cisco Systems OL-26646-01 - page 53

    3-15 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Figur e 3-8 Replacing the Fr on t Oper ations P anel Boar d 1 Hinged ribbon-cable connectors (two) 2 Securing screws (two) PCIe 1 PCIe 2 PSU 1 SYS FAN1 SYS FAN2 SYS FAN3 SYS FAN4 CPU 1 CPU 2 SYS FAN5 285 ...

  • Cisco Systems OL-26646-01 - page 54

    3-16 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Replacing a Drive Backplane Note The Small Form Factor (eight -drive) and Large Form Factor (four -drive) backplanes are factory-configurable options. When re placing a backplane, you must replace it on ...

  • Cisco Systems OL-26646-01 - page 55

    3-17 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents c. Thread the two front operati on panel ribbon cables back through t he opening in the backplane assembly . d. Reconnect the two ribbon cables to the front operations panel board. Open a hinged ribbon-c ...

  • Cisco Systems OL-26646-01 - page 56

    3-18 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Replacing Fan Modules The five fan modules in the server are numbered as follows when you ar e facing the front of the server (also see Figure 3-1 1 ). The fan numbering as designated by th e server ’ ...

  • Cisco Systems OL-26646-01 - page 57

    3-19 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Figur e 3-1 1 Replacing F an Modules Replacing DIMMs This section includes the following topics: • Memory Performance Guideli nes and Population Ru les, page 3-20 • DIMM Replacement Procedure, pa ge ...

  • Cisco Systems OL-26646-01 - page 58

    3-20 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Memory Performance Guide lines and Population Rules This section describes the ty pe of memory that th e server requires an d its effect on performance. The section includes the foll owing topics: • D ...

  • Cisco Systems OL-26646-01 - page 59

    3-21 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents DIMM Population Rules Observe the following g uidelines when installing or rep lacing DIMMs: • Each CPU supports thr ee memory channels. – CPU1 supports channels A, B, and C. – CPU2 supports channe ...

  • Cisco Systems OL-26646-01 - page 60

    3-22 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Enabling Low-Voltage DIMM Operation Y ou can enable low voltage (1.35 V) DIMM operation for all DIMMs in the server . There is a setting in the BIOS Setup utility that y ou can use to change the DDR mem ...

  • Cisco Systems OL-26646-01 - page 61

    3-23 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents DIMM Replacement Procedure T o install a DIMM assembly , follow these steps: Step 1 Remove the DIMM that you are replacing: a. Power off the server as described in the “Shuttin g Down and Powerin g Off ...

  • Cisco Systems OL-26646-01 - page 62

    3-24 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Replacing CPUs and Heatsinks This server has two CPU sockets. Each CPU supports three DIM M channels (six DIMM slots). See Figure 3-12 . This sect ion includes the following topics: • Special Informat ...

  • Cisco Systems OL-26646-01 - page 63

    3-25 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Single-CPU Restrictions The minimum configuration is that th e server must have at least CPU1 installed. Install CPU1 first, then CPU2 (see Figure 3-12 ). The following restr ictions apply when using a s ...

  • Cisco Systems OL-26646-01 - page 64

    3-26 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Figure 3-13 CPU Sock et Latc hes Step 2 Remove a protective cap or an old CPU from the so cket (if present): • If you are r emoving an old CPU, skip to Ste p 3 . • If you are installing a new CPU to ...

  • Cisco Systems OL-26646-01 - page 65

    3-27 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Step 3 Remove an old CPU: a. Set the Pick-and-Place tool on the CPU in the socket, aligning the arrow on the tool with the registration mark on the socket (the small t riangular mark). See Figu re 3-15 . ...

  • Cisco Systems OL-26646-01 - page 66

    3-28 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Figur e 3-16 CPU and Pick-and-P lace T ool on P edestal Step 5 Install a new CPU: a. Set the Pick-and-Place tool with CPU over the empty CPU socket on the motherboard. Note Align the arrow on the top of ...

  • Cisco Systems OL-26646-01 - page 67

    3-29 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents c. Apply thermal grease from an included syringe t o the top of the CPU. Apply about 2 cubic centimeters of grease (about half the syringe con tents) to the top of t he CPU in the pattern that is shown i ...

  • Cisco Systems OL-26646-01 - page 68

    3-30 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components – Heat sink cleaning kit (UCSX-HSCK=) – Thermal grease kit for C22 (UCS-CPU-GREASE=) – Intel CPU Pick-n-Place tool fo r EP CPUs (UCS- CPU-EN-PNP=) • Scenario 2—Y ou are replaci ng the existing ...

  • Cisco Systems OL-26646-01 - page 69

    3-31 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Replacing the Motherboard RTC Battery War ni ng There is danger of explosion if the battery is replaced i ncorrectly . Replace the battery only w ith the same or equivalent type rec ommended by the manuf ...

  • Cisco Systems OL-26646-01 - page 70

    3-32 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Figur e 3-18 Replacing the Motherboard RTC Bat tery Replacing a PCIe Riser The server contains two t oolless PCIe risers for hor izontal installation of PCIe cards. See Ta b l e 3 - 7 for a description ...

  • Cisco Systems OL-26646-01 - page 71

    3-33 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents c. Remove the top cover as described in “Removing and Replacing the Serv er T op Co ver” section on page 3-7 . d. Lift straight up on both ends of the PCI e riser to disengage its circuit board from ...

  • Cisco Systems OL-26646-01 - page 72

    3-34 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Replacing a PCIe Card Caution Cisco supports all PCIe cards qualified and sold by Ci sco. PCIe cards not qu alified or sold by Cisco are the responsibi lity of the custom er . A lthough Cisco w ill alwa ...

  • Cisco Systems OL-26646-01 - page 73

    3-35 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Replacing a PCIe Card Note If you are ins talling a Cisc o UCS V irtual Interfa ce Card, there ar e prerequisite considerat ions. See Special Consid erations for Cisco UCS V irtual Interface Card s, page ...

  • Cisco Systems OL-26646-01 - page 74

    3-36 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components h. If the card that you replaced was a RAID controller , continue wi th Restoring RAID Configu ration After Replacing a RAID Controller, page C-22 . Special Considerations for Ci sco UCS Virtual Interfa ...

  • Cisco Systems OL-26646-01 - page 75

    3-37 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Installing Multiple PCIe Cards and Resolving Limited Resources When a large number of PCIe add- on cards are installed in the serv er, the sy stem may run out of t he following resources r equired for PC ...

  • Cisco Systems OL-26646-01 - page 76

    3-38 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Resolving Insufficient 16-Bit I/O Space The system has only 64 KB of legacy 16-bit I/O resour ces available. This 64 KB of I/O space is divided between the CPUs in the system becau se the PCIe controlle ...

  • Cisco Systems OL-26646-01 - page 77

    3-39 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Replacing an Internal USB Flash Drive The server has one int ernal USB 2.0 sock et on the motherboard that y ou can use with a USB thumb drive for additional storage. The server can be or dered with an o ...

  • Cisco Systems OL-26646-01 - page 78

    3-40 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Figur e 3-22 Inter nal USB Flas h Dr iv e Sock et (USB 2.0) Enabling or Disabling th e Internal USB Port The factory default is for all USB ports on the server to be enabled. However , the internal USB ...

  • Cisco Systems OL-26646-01 - page 79

    3-41 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Replacing the SuperCap Power Module (RAID Backup Unit) This server sup ports installa tion of one Supe rCap power m odules (SCPMs). The SC PM mounts inside a bracket that is next to t he cooling fans (se ...

  • Cisco Systems OL-26646-01 - page 80

    3-42 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Figur e 3-23 Replacing an SCPM 1 SCPM bracket PCIe 1 PCIe 2 PSU 1 SYS FAN1 SYS FAN2 SYS FAN3 SYS FAN4 CPU 1 CPU 2 SYS FAN5 285212 1 ...

  • Cisco Systems OL-26646-01 - page 81

    3-43 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Installing a Trusted Platform Module The trusted p latform modu le (TPM) is a smal l circu it board that attaches to a motherboard socket. The socket location is on the motherboard, below PCIe riser 2 (s ...

  • Cisco Systems OL-26646-01 - page 82

    3-44 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Step 4 V erify that the TPM is now enabled. a. W atch during bootup for the F2 prompt, and then p ress F2 to enter BIOS setup. b. Log into the BIOS Setup ut ility with your BIOS Administ rator password. ...

  • Cisco Systems OL-26646-01 - page 83

    3-45 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Step 1 V erify that a TPM is now installed and enabled in th e server: a. Either attach a VGA mon itor and USB ke yboard to the server , or log in remotely to the Cisco IMC interface of the server and op ...

  • Cisco Systems OL-26646-01 - page 84

    3-46 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Replacing a SCU Upgrade ROM Module T o remove and replace a module, use the f ollowing procedure. Step 1 Prepare the server for component installation: a. Power off the server as described in Shutting D ...

  • Cisco Systems OL-26646-01 - page 85

    3-47 Cisco UCS C22 Server Inst allation and Service Gu ide OL-26646-01 Chapter 3 Maintaining the Server Installing or Replacing Server Comp onents Replacing a Software RAID Key Module T o remove and replace a softwar e RAID key module, use the following procedur e. Step 1 Prepare the server for component installation: a. Power off the server as des ...

  • Cisco Systems OL-26646-01 - page 86

    3-48 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Chapter 3 Mainta ining the Se rver Installing or Replacin g Server Components Replacing Power Supplies The server has one power supply . • See Power Specifications, page A-2 fo r more information about the support ed power supplies. • See Rear Panel LEDs and Buttons, page 3-4 ...

  • Cisco Systems OL-26646-01 - page 87

    A-1 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 APPENDIX A Server Specifications This appendix lists t he technical specification s for the server and includ es the following sections: • Physical Specifications, page A-1 • Power Specificati ons, page A-2 • Environmental Speci fication s, page A-3 Physical Specifications T ...

  • Cisco Systems OL-26646-01 - page 88

    A-2 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix A Server Sp ecifications Power Specifications Power Specifications The po wer specificatio ns for the two p ower suppl y options are listed in the follo wing sections: • 450W Power Supply , page A-2 • 650W Power Supply , page A-3 Y ou can get more specific p ower in f ...

  • Cisco Systems OL-26646-01 - page 89

    A-3 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix A Server Spec ifications Environmen tal Specificat ions 650W Power Supply Ta b l e A - 3 lists the specifications fo r each 650W power supply (Cisco par t number UCSC-PSU-650W). Environmental Specifications Ta b l e A - 4 lists the environmental specificatio ns for the se ...

  • Cisco Systems OL-26646-01 - page 90

    A-4 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix A Server Sp ecifications Environmental Specifications ...

  • Cisco Systems OL-26646-01 - page 91

    B-1 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 APPENDIX B Power Cord Specifications This appendix pro vides supp orted pow er cable specif ications. Supported Power Cords and Plugs Each po wer supply has a sep arate po wer cord. Standa rd po wer cords or jumper po wer cords are a vailable for connection to the server . The jum ...

  • Cisco Systems OL-26646-01 - page 92

    B-2 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix B Power Cord Specifications Supported Power Cords and Plugs CAB-9K10A- IT Pow er Cord, 250 V A C 10 A CEI 23-16 Plug Italy 8.2 2.5 Figure B-7 CAB-9K10A- SW Pow er Cord, 250 V A C 10 A MP232 Plug Switzerland 8.2 2.5 Figure B-8 CAB-9K10A- UK Pow er Cord, 250 V A C 10 A BS13 ...

  • Cisco Systems OL-26646-01 - page 93

    B-3 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix B Po wer Cord Specifications Supported Power Cords and Plugs AC Power Cord Illustrations This section includes the A C po wer cord illustrations. See Figure B-1 through Figure B-15 . Figure B-1 SFS-250V - 1 0A- AR Figur e B-2 CAB-9K1 0A -AU Figure B-3 SFS-250V -10 A -CN 1 ...

  • Cisco Systems OL-26646-01 - page 94

    B-4 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix B Power Cord Specifications Supported Power Cords and Plugs Figur e B-4 CAB-9K1 0A -EU Figur e B-5 SFS-250V -1 0A -ID Figur e B-6 SFS-250V -1 0A -IS Connector : V S CC15 Cord s et rating: 10A/16 A, 250 V Length: 8 ft 2 in. (2.5 m) Plug: M2511 1 8 6576 OVE Cord s et rating ...

  • Cisco Systems OL-26646-01 - page 95

    B-5 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix B Po wer Cord Specifications Supported Power Cords and Plugs Figur e B-7 CAB-9K1 0A -IT Figur e B-8 CAB-9K1 0A -SW Figur e B-9 CAB-9K1 0A -UK Plug: I/ 3 G (CEI 2 3 -16) Connector C15M (EN60 3 20/C15 ) Cord s et rating: 10 A, 250 V Length: 8 ft 2 in. (2.5 m) 1 8 6575 Plug: ...

  • Cisco Systems OL-26646-01 - page 96

    B-6 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix B Power Cord Specifications Supported Power Cords and Plugs Figure B-1 0 CAB-AC-250V/13A Figur e B-1 1 CAB-N5K6A -NA Figur e B-12 CAB-9K12A -NA Cord s et rating 1 3 A, 250V (6.6 f eet) (79±2m) Plug: EL 3 12MoldedT wi s tlock (NEMA L6-20) 1 8 656 8 Connector : EL 701 (IEC ...

  • Cisco Systems OL-26646-01 - page 97

    B-7 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix B Po wer Cord Specifications Supported Power Cords and Plugs Figur e B-13 CAB-C13-CBN, Jump er P ow er Cord (0.68 m) Figur e B-14 CAB-C13-C14-2M, Jumper P ower Cord (2 m) Figur e B-15 CAB-C13-C14-AC, Jumper P ower Cor d (3 m) Cord s et rating 10A, 250V (6 8 6mm) Plug: SS ...

  • Cisco Systems OL-26646-01 - page 98

    B-8 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix B Power Cord Specifications Supported Power Cords and Plugs ...

  • Cisco Systems OL-26646-01 - page 99

    C-1 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 APPENDIX C RAID Controller Considerations This appendix contain s the follo wing sections: • Supported RAID Cont rollers and Required Cabl es, page C-2 • Mixing Dri v e T ypes in RAID Groups, page C-3 • SuperCap Po wer Modules (RAI D Backup Units), page C-4 • RAID Controll ...

  • Cisco Systems OL-26646-01 - page 100

    C-2 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Supported RAID Cont rollers and Required Cab les Supported RAID Controllers and Required Cables This server supports the RAID controller options an d cable requirements sh o wn in Ta b l e C - 1 for the small form factor v ersion, or Ta b ...

  • Cisco Systems OL-26646-01 - page 101

    C-3 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Mixing Drive Types in RAID Groups Ta b l e C - 2 lists the RAID options for the large form f actor (LFF) version of the serv er . Mixing Drive Types in RAID Groups Ta b l e C - 3 lists the technical capabilities for mixin g hard disk dri v ...

  • Cisco Systems OL-26646-01 - page 102

    C-4 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations SuperCap Power Module s (RAID Backup Units) SuperCap Power Modules (RAID Backup Units) T his server supp orts installation of one SuperCap power module (SCPM). The backup unit mounts to a holder near the cooling fans (see Figure 3-23 ). Th ...

  • Cisco Systems OL-26646-01 - page 103

    C-5 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controller Embedded RAID Controller Note VMware ESX/ESXi or any other virtualize d en vironments are not supporte d for use with the embedd ed MegaRAID controller . Hypervisors such as Hyp er -V , Xen, or KV M are also not su ...

  • Cisco Systems OL-26646-01 - page 104

    C-6 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controlle r Notes on Supported Embedded MegaRAID Levels The follo wing RAID le v els are supported by the embedded Me gaRAID control ler . • RAID 0—Y ou can configur e a RAID 0 virtual dri v e (VD) using one or more phy s ...

  • Cisco Systems OL-26646-01 - page 105

    C-7 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controller Installing a SCU Upgrade ROM Modu le For Embedded RAID SAS Support The SCU Upgrade R OM module contains a chip on a small circuit board . This module attaches t o a motherboard header . T his chip adds SAS support ...

  • Cisco Systems OL-26646-01 - page 106

    C-8 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controlle r Installing a Software RAID Key Module for Embedded RAID 5 Support The software RAID key module cont ains a chip on a small c ircuit bo ard. This module attaches to a motherboard header . This chip upgrades SAS sup ...

  • Cisco Systems OL-26646-01 - page 107

    C-9 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controller Disabling the Embedded RAID Controller in the BIOS Caution Data migration from SW RAID to HW RAID is not sup ported and could result in data loss. Mig rations from SW RAID to HW RAID are supported onl y befor e the ...

  • Cisco Systems OL-26646-01 - page 108

    C-10 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controlle r • Down loading the LSI Me gaSR Dri v ers, page C-10 • Microsoft W indo ws Dri v er Installation, page C-10 • Linux Dri ver I nstallation, page C-13 Downloading the LSI MegaSR Drivers The MegaSR dri vers are ...

  • Cisco Systems OL-26646-01 - page 109

    C-11 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controller Step 3 Prepare the dri vers on a USB thumb dri ve: a. Burn the ISO image to a disc. b. Browse the contents of the dri vers folders to the l ocation of the embedded Me gaRAID dri vers: /< OS >/Storage/Int el/ ...

  • Cisco Systems OL-26646-01 - page 110

    C-12 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controlle r Step 4 On the Dri ver tab, click Update Dri ver to open the Update De vice D riv er wizard, and then follo w the wizard instructions to update t he driv er . ...

  • Cisco Systems OL-26646-01 - page 111

    C-13 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controller Linux Driver Installation This section e xplains the st eps to install the embedded Me gaRAID de vice d riv er in a Red Hat Enterprise Linux installation o r a SuSE Linux Enterprise Serv er installation. This sect ...

  • Cisco Systems OL-26646-01 - page 112

    C-14 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controlle r Step 4 If necessary , use this command to change the f ile name of the dri ver update disk to a name with fe wer than eight characters: copy dud-[ driver version ].img dud.img Step 5 Open the DOS Co mmand Prompt ...

  • Cisco Systems OL-26646-01 - page 113

    C-15 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controller Installing the Red Hat Linux Driver For the specif ic supported OS versions, see the Hardware and Software Interoperability Matrix for your server release. This section describes the fresh i nstallation of the Red ...

  • Cisco Systems OL-26646-01 - page 114

    C-16 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controlle r Note The noprobe v alues depend on the number of drives. For e xample, to inst all RHEL 5.7 on a RAID 5 conf iguration with three dri ves, enter: Linux dd blacklist=isci blacklist=ahci nopr obe=ata1 nopro be=ata2 ...

  • Cisco Systems OL-26646-01 - page 115

    C-17 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Embedded RAID Controller • T o install from local media: Connect an external USB D VD driv e to the serv er and then insert the first RHEL i nstall disc into the dri ve. Skip to Step 6 . • T o install from remote ISO: Log in to the se ...

  • Cisco Systems OL-26646-01 - page 116

    C-18 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations RAID Controller Cabling RAID Controller Cabling This section includes the following topics: • Cable Routing, page C-18 • Cisco UCS C22 Server Cabling, p age C-19 Cable Routing The RAID controll er connectors in this server are sho wn ...

  • Cisco Systems OL-26646-01 - page 117

    C-19 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations RAID Controller Cabling Cisco UCS C22 Server Cabling This section contains the following topics: • Backplane and Expander Options, page C-19 • Small Form Factor 8-Dri ve Ba ckplane Cabling , page C-19 • Large F orm Fa ctor 4-Dri ve ...

  • Cisco Systems OL-26646-01 - page 118

    C-20 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations RAID Controller Cabling LSI MegaRAID 9220-4i PCIe Card This option can control up to four i nternal dri ves. The required UCSC-CABLE-A5 cable kit has two mi ni-SAS cables. Cable 1 controls dri v es 1–4. Step 1 Connect mini-SAS cabl e 1 ...

  • Cisco Systems OL-26646-01 - page 119

    C-21 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations RAID Controller Cabling Large Form Factor 4- Drive Backplane Cabling The cable connections required for each t ype of controller ar e as follows: • Embedded RAID, page C-21 • LSI MegaRAID 9220-4i PCIe Card, page C-21 • LSI MegaRAID ...

  • Cisco Systems OL-26646-01 - page 120

    C-22 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations Restoring RAID Configuration After Replacing a RAID Cont roller Restoring RAID Configuration After Replacing a RAID Controller When you replace a RAID controller , the RAID configuration th at is stored in the controller is lost. Use the ...

  • Cisco Systems OL-26646-01 - page 121

    C-23 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations For More Information http://www .cisco.com/en/US/docs/unified_computing/uc s/3rd-party/lsi/mrsas/userguide/LSI_MR_SAS_SW_UG.pdf ...

  • Cisco Systems OL-26646-01 - page 122

    C-24 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix C RAID Controller Considerations For More Information ...

  • Cisco Systems OL-26646-01 - page 123

    D-1 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 APPENDIX D Installation for Cisco UCS Integration The Cisco UCS integratio n instructions ha ve been mov ed to the integratio n guides found here: Cisco UCS C-Series Server I nte gration wit h UCS Manager Guides Refer to the guide that is for the versio n of Cisco UCS Manager that ...

  • Cisco Systems OL-26646-01 - page 124

    D-2 Cisco UCS C22 Server Insta llation and Service Guide OL-26646-01 Appendix D Installati on for Cisco UCS Integration ...

Manufacturer Cisco Systems Category Server

Documents that we receive from a manufacturer of a Cisco Systems OL-26646-01 can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- OL-26646-01 manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems OL-26646-01
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems OL-26646-01.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems OL-26646-01, service manual, brief instructions and user manuals Cisco Systems OL-26646-01. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems OL-26646-01.

Similar manuals

A complete manual for the device Cisco Systems OL-26646-01, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems OL-26646-01 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems OL-26646-01.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems OL-26646-01 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems OL-26646-01, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems OL-26646-01, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems OL-26646-01 - which should help us in our first steps of using Cisco Systems OL-26646-01
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems OL-26646-01
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems OL-26646-01 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems OL-26646-01?

Use the form below

If you did not solve your problem by using a manual Cisco Systems OL-26646-01, ask a question using the form below. If a user had a similar problem with Cisco Systems OL-26646-01 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)