English dropdown-ico

Manual Porter-Cable FM350A

15 pages 1.93 mb
Download

Go to site of 15

Summary
  • Porter-Cable FM350A - page 1

    CLIPPED HEAD FRAMING NAILER Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPOR ...

  • Porter-Cable FM350A - page 2

    2 PORTER ✦ ✦ CABLE Porter-Cable Corporation 4825 Highway 45 North Jackson, TN 38305 Date of Manufacture: ___________________________ Fecha de fabricación:, Date de fabrication: Serial No: ______________________________________ Número de serie:, Nombre d'ordre GB ENGLISH EC-DECLARA TION OF CONFORMITY We declare under our sole responsibili ...

  • Porter-Cable FM350A - page 3

    3 indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. used without the safety al ...

  • Porter-Cable FM350A - page 4

    4 Fig. 6 Fig. 5 Fig. 2 Fig. 3 Fig. 4 1. Read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS INJURY . Fig. 1. 2 . Operator and others in work area MUST wear safety glasses with side shields. These safety glasses must conform to ANSI Z87.1 requirements (approved glasses have “Z87” printed or sta ...

  • Porter-Cable FM350A - page 5

    5 9. Do not connect tool to pressure which potentially exceeds 200 PSI (13.7 BAR). 1 0 . All air line components (hoses, connectors, filters, regulators, etc.) must be rated for a maximum working pressure of at least 150 PSI (10.3 BAR) or 150% of the maximum system pressure, which ever is greater. 11. Connect tool to air supply hose with a coupling ...

  • Porter-Cable FM350A - page 6

    6 21. Remove finger from trigger when not driving fasteners. Never carry tool with finger on trigger. In “Contact Actuation Mode” tool will fire a fastener if safety is bumped while trigger is depressed. Fig. 14. 22. Do not overreach. Keep proper footing and balance at all times when using or handling the tool. 23. Fire fasteners into work surf ...

  • Porter-Cable FM350A - page 7

    7 Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS IN ...

  • Porter-Cable FM350A - page 8

    8 PREP ARING THE TOOL 1. After reading and understanding this entire manual, connect tool to air supply (Fig. 18). 2. Orient a strip of approved fasteners with points down (A) Fig. 19, align, and insert into the magazine “T” slot points first. Do not load fastener strip into magazine backwards. 3. Observe fastener icon (A) Fig. 20. Insert faste ...

  • Porter-Cable FM350A - page 9

    9 6 . Adjust directional exhaust deflector (A) Fig. 22, so that the exhaust air blast will be directed away from the operator. The exhaust deflector provides eight detented positions for directing the exhaust blast away from the operator. Grasp the deflector and rotate it to the desired position for the current application. USING THE TOOL WITH SELE ...

  • Porter-Cable FM350A - page 10

    10 Disconnect tool from air supply before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person. Clean and inspect tool daily. Carefully check for proper operation of trigger and safety mechanism. Do Not use the tool unless both the trigger and the safety mechan ...

  • Porter-Cable FM350A - page 11

    11 CLEARING A JAMMED F ASTENER Disconnect tool from air supply. 1. Remove any remaining fasteners from the nailer. A. Place finger in recess (A) Fig. 28, and depress lever to release follower mechanism. B. With follower release button (A) Fig. 28 depressed, slide follower all the way to the front of the magazine. C. Depress nail stop (B) Fig. 29, s ...

  • Porter-Cable FM350A - page 12

    12 CLEAN AND INSPECT DAIL Y Disconnect tool from air supply before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions. Such solutions can damage int ...

  • Porter-Cable FM350A - page 13

    13 TROUBLESHOOTING Disconnect tool from air supply before performing any Service Procedure. SYMPTOM PROBLEMS SOLUTIONS 1. Air leak near top of Loose screws. Tighten screws. tool or in trigger area. Worn or damaged Install Overhaul Kit. o-rings or seals. 2. Tool does nothing or Inadequate air supply. Verify adequate air supply. operates sluggishly. ...

  • Porter-Cable FM350A - page 14

    14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material ...

  • Porter-Cable FM350A - page 15

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

Manufacturer Porter-Cable Category Nail Gun

Documents that we receive from a manufacturer of a Porter-Cable FM350A can be divided into several groups. They are, among others:
- Porter-Cable technical drawings
- FM350A manuals
- Porter-Cable product data sheets
- information booklets
- or energy labels Porter-Cable FM350A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Porter-Cable FM350A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Porter-Cable FM350A, service manual, brief instructions and user manuals Porter-Cable FM350A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Porter-Cable FM350A.

Similar manuals

A complete manual for the device Porter-Cable FM350A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Porter-Cable FM350A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Porter-Cable FM350A.

A complete Porter-Cable manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Porter-Cable FM350A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Porter-Cable FM350A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Porter-Cable FM350A, that we can find in the current document
3. Tips how to use the basic functions of the device Porter-Cable FM350A - which should help us in our first steps of using Porter-Cable FM350A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Porter-Cable FM350A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Porter-Cable FM350A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Porter-Cable FM350A?

Use the form below

If you did not solve your problem by using a manual Porter-Cable FM350A, ask a question using the form below. If a user had a similar problem with Porter-Cable FM350A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)